From: Neil Armstrong <narmstrong@baylibre.com>
To: Jerome Brunet <jbrunet@baylibre.com>
Cc: linux-amlogic@lists.infradead.org, linux-clk@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH 3/3] clk: meson-g12a: add PCIE PLL clocks
Date: Tue, 19 Mar 2019 10:58:44 +0100 [thread overview]
Message-ID: <9e2a4785-2bd5-c0a2-a5d7-73326b8b417f@baylibre.com> (raw)
In-Reply-To: <f160590677d4eb03c31c7cb81fbca20d8916c460.camel@baylibre.com>
On 19/03/2019 10:55, Jerome Brunet wrote:
> On Thu, 2019-03-07 at 15:14 +0100, Neil Armstrong wrote:
>> Add the PCIe reference clock feeding the USB3 + PCIE combo PHY.
>>
>> This PLL needs a very precise register sequence to permit to be locked,
>> thus using the specific clk-pll pcie ops.
>>
>> The PLL is then followed by :
>> - a fixed /2 divider
>> - a 5-bit 1-based divider
>> - a final /2 divider
>>
>> This reference clock is fixed to 100MHz, thus only a single PLL setup
>> is added.
>>
>> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
>> ---
>> drivers/clk/meson/g12a.c | 118 +++++++++++++++++++++++++++++++++++++++
>> drivers/clk/meson/g12a.h | 5 +-
>> 2 files changed, 122 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/clk/meson/g12a.c b/drivers/clk/meson/g12a.c
>> index 80a7172df2a6..d382c21a29e5 100644
>> --- a/drivers/clk/meson/g12a.c
>> +++ b/drivers/clk/meson/g12a.c
>> @@ -614,6 +614,118 @@ static struct clk_regmap g12a_hifi_pll = {
>> },
>> };
>>
>> +/*
>> + * The Meson G12A PCIE PLL is fined tuned to deliver a very precise
>> + * 100MHz reference clock for the PCIe Analog PHY, and thus requires
>> + * a strict register sequence to enable the PLL.
>> + */
>> +static const struct reg_sequence g12a_pcie_pll_init_regs[] = {
>> + { .reg = HHI_PCIE_PLL_CNTL0, .def = 0x20090496 },
>> + { .reg = HHI_PCIE_PLL_CNTL0, .def = 0x30090496 },
>> + { .reg = HHI_PCIE_PLL_CNTL1, .def = 0x00000000 },
>> + { .reg = HHI_PCIE_PLL_CNTL2, .def = 0x00001100 },
>> + { .reg = HHI_PCIE_PLL_CNTL3, .def = 0x10058e00 },
>> + { .reg = HHI_PCIE_PLL_CNTL4, .def = 0x000100c0 },
>> + { .reg = HHI_PCIE_PLL_CNTL5, .def = 0x68000048 },
>> + { .reg = HHI_PCIE_PLL_CNTL5, .def = 0x68000068, .delay_us = 20 },
>> + { .reg = HHI_PCIE_PLL_CNTL4, .def = 0x008100c0, .delay_us = 10 },
>> + { .reg = HHI_PCIE_PLL_CNTL0, .def = 0x34090496 },
>> + { .reg = HHI_PCIE_PLL_CNTL0, .def = 0x14090496, .delay_us = 10 },
>> + { .reg = HHI_PCIE_PLL_CNTL2, .def = 0x00001000 },
>> +};
>> +
>> +/* Keep a single entry table for recalc/round_rate() ops */
>> +static const struct pll_params_table g12a_pcie_pll_table[] = {
>> + PLL_PARAMS(150, 1),
>> + {0, 0},
>> +};
>> +
>> +static struct clk_regmap g12a_pcie_pll_dco = {
>> + .data = &(struct meson_clk_pll_data){
>> + .en = {
>> + .reg_off = HHI_PCIE_PLL_CNTL0,
>> + .shift = 28,
>> + .width = 1,
>> + },
>> + .m = {
>> + .reg_off = HHI_PCIE_PLL_CNTL0,
>> + .shift = 0,
>> + .width = 8,
>> + },
>> + .n = {
>> + .reg_off = HHI_PCIE_PLL_CNTL0,
>> + .shift = 10,
>> + .width = 5,
>> + },
>> + .frac = {
>> + .reg_off = HHI_PCIE_PLL_CNTL1,
>> + .shift = 0,
>> + .width = 12,
>> + },
>> + .l = {
>> + .reg_off = HHI_PCIE_PLL_CNTL0,
>> + .shift = 31,
>> + .width = 1,
>> + },
>> + .rst = {
>> + .reg_off = HHI_PCIE_PLL_CNTL0,
>> + .shift = 29,
>> + .width = 1,
>> + },
>> + .table = g12a_pcie_pll_table,
>> + .init_regs = g12a_pcie_pll_init_regs,
>> + .init_count = ARRAY_SIZE(g12a_pcie_pll_init_regs),
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "pcie_pll_dco",
>> + .ops = &meson_clk_pcie_pll_ops,
>> + .parent_names = (const char *[]){ IN_PREFIX "xtal" },
>> + .num_parents = 1,
>> + },
>> +};
>> +
>> +static struct clk_fixed_factor g12a_pcie_pll_dco_div2 = {
>> + .mult = 1,
>> + .div = 2,
>> + .hw.init = &(struct clk_init_data){
>> + .name = "pcie_pll_dco_div2",
>> + .ops = &clk_fixed_factor_ops,
>> + .parent_names = (const char *[]){ "pcie_pll_dco" },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT,
>> + },
>> +};
>> +
>> +static struct clk_regmap g12a_pcie_pll_od = {
>> + .data = &(struct clk_regmap_div_data){
>> + .offset = HHI_PCIE_PLL_CNTL0,
>> + .shift = 16,
>> + .width = 5,
>> + .flags = CLK_DIVIDER_ROUND_CLOSEST |
>> + CLK_DIVIDER_ONE_BASED |
>> + CLK_DIVIDER_ALLOW_ZERO,
>
> That's unusual !
> Ods have always been power of two divider so far. I suppose you have noticed
> and checked this as well ?
>
Yes, I've checked and validated it. Without CLK_DIVIDER_ONE_BASED,
the divider is off by 1. And CLK_DIVIDER_ALLOW_ZERO since at reset,
0 is the default register value.
> That being said, the doc seems to imply that the global post divider will
> divide by 36, which seems difficult to reach with powers of two.
>
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "pcie_pll_od",
>> + .ops = &clk_regmap_divider_ops,
>> + .parent_names = (const char *[]){ "pcie_pll_dco_div2" },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT,
>> + },
>> +};
>> +
>> +static struct clk_fixed_factor g12a_pcie_pll = {
>> + .mult = 1,
>> + .div = 2,
>> + .hw.init = &(struct clk_init_data){
>> + .name = "pcie_pll_pll",
>> + .ops = &clk_fixed_factor_ops,
>> + .parent_names = (const char *[]){ "pcie_pll_od" },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT,
>> + },
>> +};
>> +
>> static struct clk_regmap g12a_hdmi_pll_dco = {
>> .data = &(struct meson_clk_pll_data){
>> .en = {
>> @@ -2499,6 +2611,10 @@ static struct clk_hw_onecell_data g12a_hw_onecell_data = {
>> [CLKID_CPU_CLK_AXI] = &g12a_cpu_clk_axi.hw,
>> [CLKID_CPU_CLK_TRACE_DIV] = &g12a_cpu_clk_trace_div.hw,
>> [CLKID_CPU_CLK_TRACE] = &g12a_cpu_clk_trace.hw,
>> + [CLKID_PCIE_PLL_DCO] = &g12a_pcie_pll_dco.hw,
>> + [CLKID_PCIE_PLL_DCO_DIV2] = &g12a_pcie_pll_dco_div2.hw,
>> + [CLKID_PCIE_PLL_OD] = &g12a_pcie_pll_od.hw,
>> + [CLKID_PCIE_PLL] = &g12a_pcie_pll.hw,
>> [NR_CLKS] = NULL,
>> },
>> .num = NR_CLKS,
>> @@ -2685,6 +2801,8 @@ static struct clk_regmap *const g12a_clk_regmaps[] = {
>> &g12a_cpu_clk_axi,
>> &g12a_cpu_clk_trace_div,
>> &g12a_cpu_clk_trace,
>> + &g12a_pcie_pll_od,
>> + &g12a_pcie_pll_dco,
>> };
>>
>> static const struct meson_eeclkc_data g12a_clkc_data = {
>> diff --git a/drivers/clk/meson/g12a.h b/drivers/clk/meson/g12a.h
>> index 70aa469ca1cf..1393a09730a6 100644
>> --- a/drivers/clk/meson/g12a.h
>> +++ b/drivers/clk/meson/g12a.h
>> @@ -186,8 +186,11 @@
>> #define CLKID_CPU_CLK_AXI 195
>> #define CLKID_CPU_CLK_TRACE_DIV 196
>> #define CLKID_CPU_CLK_TRACE 197
>> +#define CLKID_PCIE_PLL_DCO 198
>> +#define CLKID_PCIE_PLL_DCO_DIV2 199
>> +#define CLKID_PCIE_PLL_OD 200
>>
>> -#define NR_CLKS 198
>> +#define NR_CLKS 202
>>
>> /* include the CLKIDs that have been made part of the DT binding */
>> #include <dt-bindings/clock/g12a-clkc.h>
>
>
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
next prev parent reply other threads:[~2019-03-19 9:59 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-03-07 14:14 [PATCH 0/3] clk: meson: add support for PCIE PLL Neil Armstrong
2019-03-07 14:14 ` [PATCH 1/3] clk: meson-pll: add reduced specific clk_ops for G12A PCIe PLL Neil Armstrong
2019-03-07 14:14 ` [PATCH 2/3] dt-bindings: clk: g12a-clkc: add PCIE PLL clock ID Neil Armstrong
2019-03-27 23:47 ` Rob Herring
2019-03-07 14:14 ` [PATCH 3/3] clk: meson-g12a: add PCIE PLL clocks Neil Armstrong
2019-03-19 9:55 ` Jerome Brunet
2019-03-19 9:58 ` Neil Armstrong [this message]
2019-03-19 10:01 ` [PATCH 0/3] clk: meson: add support for PCIE PLL Jerome Brunet
2019-03-19 20:23 ` Neil Armstrong
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=9e2a4785-2bd5-c0a2-a5d7-73326b8b417f@baylibre.com \
--to=narmstrong@baylibre.com \
--cc=jbrunet@baylibre.com \
--cc=linux-amlogic@lists.infradead.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).