Hi Anand,

On Sat, Feb 9, 2019 at 6:55 PM Anand Moon <linux.amoon@gmail.com> wrote:
[...]
> > > But this dose not work setting the usb1_phy to use vbus-supply.
> > >
> > >  &usb1_phy {
> > >         status = "okay";
> > > +       vbus-supply = <&usb_vbus>;
> > >  };
> > >
> > > I am attaching a small patch for testing.
> > > [0] usbvbus.patch
> > indeed, this is not working for me either.
> > I checked my old notes at [0] -> it works for me when setting
> > "vbus-supply" at the usb controller (not the PHY).
> >
> > with the following snippet:
> >   &usb1 {
> >     status = "okay";
> >     vbus-supply = <&usb_vbus>;
> >   };
> > I get:
> > # cat /sys/kernel/debug/regulator/regulator_summary | grep -i usb
> >    c90c0000.usb                  1                                 0mA
> >     0mV     0mV
> >    c90c0000.usb                  1                                 0mA
> >     0mV     0mV
> >    USB_VBUS                      1    1      0 unknown  5000mV     0mA
> >  5000mV  5000mV
> >       c90c0000.usb               1                                 0mA
> >     0mV     0mV
> >
> > can you please try this on your board as well?
> >
> > > Here is the summary of the above patch.
> > >
> > > 1. hot-plugins of usb device is not working.
> > > 2. only cold/warm boot let the device come up.
> > > 3. not power is supplied to the usb ports.
> > > 4. no power module is registered with the regulator summary.
> > with "vbus-supply" moved to the usb1 node I get the following result:
> > 1. same: hot-plugins of usb device is not working
> > 2. different: a reboot doesn't make devices come up
> > 3. same: no power is supplied to the USB ports (in my case this causes
> > #2, but it's not clear why there's no power...)
> > 4. different: the regulator is registered with the USB controller in debugfs
> >
> Here the the logs after I applied the above changes
>
> [1] https://pastebin.com/rVa8gxNG
can you please provide the .dts patch for this log?
I can see the following message in your log:
[    1.977367] USB_VBUS: disabling

I have tried it with the attached patch, then I get:
# dmesg | grep VBUS
#
# cat /sys/kernel/debug/regulator/regulator_summary
regulator                      use open bypass  opmode voltage current
    min     max
---------------------------------------------------------------------------------------
regulator-dummy                  4    3      0 unknown     0mV     0mA
    0mV     0mV
   c90c0000.usb                  1                                 0mA
    0mV     0mV
   c90c0000.usb                  1                                 0mA
    0mV     0mV
   VCCK                          1    1      0 unknown   860mV     0mA
  860mV  1140mV
      cpu0                       0                                 0mA
  860mV   860mV
P5V0                             3    4      0 unknown  5000mV     0mA
 5000mV  5000mV
   VCC1V8                        2    2      0 unknown  1800mV     0mA
 1800mV  1800mV
      c1108680.adc               1                                 0mA
    0mV     0mV
      c1108e00.mmc               1                                 0mA
 1800mV  1950mV
   VCC3V3                        2    3      0 unknown  3300mV     0mA
 3300mV  3300mV
      c1108e00.mmc               1                                 0mA
 3300mV  3400mV
      VDD_RTC                    0    0      0 unknown   900mV     0mA
  900mV   900mV
      TFLASH_VDD                 1    1      0 unknown  3300mV     0mA
 3300mV  3300mV
         c1108c20.mmc:slot@1     1                                 0mA
 3300mV  3400mV
   DDR_VDDC                      0    0      0 unknown  1500mV     0mA
 1500mV  1500mV
   USB_VBUS                      1    1      0 unknown  5000mV     0mA
 5000mV  5000mV
      c90c0000.usb               1                                 0mA
    0mV     0mV
TF_IO                            0    1      0 unknown  3300mV     0mA
 1800mV  3300mV
   c1108c20.mmc:slot@1           0                                 0mA
    0mV     0mV

(my kernel build includes two more changes on top of Kevin's v5.1/dt
branch which add two new regulators: it enables the RTC and the SDHC
MMC controller, but these are not related to USB at all)

USB ist still not working for me, but I believe my problem is
different to yours.


Regards

Martin