Re: [PATCH v2 2/3] pinctrl: meson-a1: add pinctrl driver for Meson A1 Soc

[Neil Armstrong <narmstrong@baylibre.com>]

Hi,

On 08/10/2019 13:09, Qianggui Song wrote:
> Add pinctrl driver for Meson A1 Soc which share the same register layout of
> pinmux with previous Meson-G12A, however there is difference for gpio
> and pin config register in A1.The main difference is that registers before A1
> are grouped by function while those of A1 are by bank. The new register layout
> is as below:
> 
> /* first bank */	      /* addr */
> - P_PADCTRL_GPIOP_I         base + 0x00 << 2
> - P_PADCTRL_GPIOP_O         base + 0x01 << 2
> - P_PADCTRL_GPIOP_OEN       base + 0x02 << 2
> - P_PADCTRL_GPIOP_PULL_EN   base + 0x03 << 2
> - P_PADCTRL_GPIOP_PULL_UP   base + 0x04 << 2
> - P_PADCTRL_GPIOP_DS        base + 0x05 << 2
> 
> /* second bank */
> - P_PADCTRL_GPIOB_I         base + 0x10 << 2
> - P_PADCTRL_GPIOB_O         base + 0x11 << 2
> - P_PADCTRL_GPIOB_OEN       base + 0x12 << 2
> - P_PADCTRL_GPIOB_PULL_EN   base + 0x13 << 2
> - P_PADCTRL_GPIOB_PULL_UP   base + 0x14 << 2
> - P_PADCTRL_GPIOB_DS        base + 0x15 << 2
> 
> Each bank contains at least 6 registers to be configured, if one bank has
> more than 16 gpios, an extra P_PADCTRL_GPIO[X]_DS_EXT is included. Between
> two adjacent P_PADCTRL_GPIO[X]_I, there is an offset 0x10, that is to say,
> for third bank, the offsets will be 0x20,0x21,0x22,0x23,0x24,0x25 according
> to above register layout.For privous chips, registers are grouped
> according to their functions while registers of A1 are according to bank.
> 
> Current Meson pinctrl driver can cover such change by using base address of
> GPIO as that of drive-strength. While simply giving reg_ds = reg_pullen
> make wrong value to reg_ds for Socs that do not support drive-strength like
> AXG.To make things simple, add an extra dt parser function for a1 or later chip
> and remain the old dt parser function for old Socs.
> 
> Also note that there is no AO bank in A1.
> 
> Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
> ---
>  drivers/pinctrl/meson/Kconfig            |   6 +
>  drivers/pinctrl/meson/Makefile           |   1 +
>  drivers/pinctrl/meson/pinctrl-meson-a1.c | 942 +++++++++++++++++++++++++++++++
>  drivers/pinctrl/meson/pinctrl-meson.c    |  16 +-
>  drivers/pinctrl/meson/pinctrl-meson.h    |   5 +
>  5 files changed, 969 insertions(+), 1 deletion(-)
>  create mode 100644 drivers/pinctrl/meson/pinctrl-meson-a1.c
> 

[...]

> --- a/drivers/pinctrl/meson/pinctrl-meson.c
> +++ b/drivers/pinctrl/meson/pinctrl-meson.c
> @@ -695,6 +695,17 @@ static int meson_pinctrl_parse_dt(struct meson_pinctrl *pc,
>  	return 0;
>  }
>  
> +int meson_pinctrl_parse_dt_extra(struct meson_pinctrl *pc,
> +				 struct device_node *node)
> +{
> +	int ret;
> +
> +	ret = meson_pinctrl_parse_dt(pc, node);
> +	pc->reg_ds = pc->reg_pullen;
> +
> +	return ret;
> +}
> +
>  int meson_pinctrl_probe(struct platform_device *pdev)
>  {
>  	struct device *dev = &pdev->dev;
> @@ -708,7 +719,10 @@ int meson_pinctrl_probe(struct platform_device *pdev)
>  	pc->dev = dev;
>  	pc->data = (struct meson_pinctrl_data *) of_device_get_match_data(dev);
>  
> -	ret = meson_pinctrl_parse_dt(pc, dev->of_node);
> +	if (pc->data->parse_dt)
> +		ret = pc->data->parse_dt(pc, dev->of_node);
> +	else
> +		ret = meson_pinctrl_parse_dt(pc, dev->of_node);
>  	if (ret)
>  		return ret;
>  
> diff --git a/drivers/pinctrl/meson/pinctrl-meson.h b/drivers/pinctrl/meson/pinctrl-meson.h
> index c696f3241a36..ca29efd90aac 100644
> --- a/drivers/pinctrl/meson/pinctrl-meson.h
> +++ b/drivers/pinctrl/meson/pinctrl-meson.h
> @@ -11,6 +11,7 @@
>  #include <linux/regmap.h>
>  #include <linux/types.h>
>  
> +struct meson_pinctrl;
>  /**
>   * struct meson_pmx_group - a pinmux group
>   *
> @@ -114,6 +115,7 @@ struct meson_pinctrl_data {
>  	unsigned int num_banks;
>  	const struct pinmux_ops *pmx_ops;
>  	void *pmx_data;
> +	int (*parse_dt) (struct meson_pinctrl *pc, struct device_node *node);
>  };
>  
>  struct meson_pinctrl {
> @@ -171,3 +173,6 @@ int meson_pmx_get_groups(struct pinctrl_dev *pcdev,
>  
>  /* Common probe function */
>  int meson_pinctrl_probe(struct platform_device *pdev);
> +/* Extra dt parser function for register layout grouped by bank */
> +int meson_pinctrl_parse_dt_extra(struct meson_pinctrl *pc,
> +				 struct device_node *node);
> 

I think you should add this parse_dt callback in a separate patch.

Neil

_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic