Linux-ARM-Kernel Archive on lore.kernel.org
 help / color / Atom feed
* [PATCH v6] arm64: dts: qcom: sc7180: Add WCN3990 WLAN module device node
@ 2020-02-04 13:18 Rakesh Pillai
  2020-02-07  6:41 ` Sibi Sankar
  2020-03-24 17:39 ` Evan Green
  0 siblings, 2 replies; 6+ messages in thread
From: Rakesh Pillai @ 2020-02-04 13:18 UTC (permalink / raw)
  To: devicetree; +Cc: linux-arm-msm, Rakesh Pillai, linux-kernel, linux-arm-kernel

Add device node for the ath10k SNOC platform driver probe
and add resources required for WCN3990 on sc7180 soc.

Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
---
 arch/arm64/boot/dts/qcom/sc7180-idp.dts |  5 +++++
 arch/arm64/boot/dts/qcom/sc7180.dtsi    | 27 +++++++++++++++++++++++++++
 2 files changed, 32 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
index 388f50a..167f68ac 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
@@ -287,6 +287,11 @@
 	vdda-pll-supply = <&vreg_l4a_0p8>;
 };
 
+&wifi {
+	status = "okay";
+	qcom,msa-fixed-perm;
+};
+
 /* PINCTRL - additions to nodes defined in sc7180.dtsi */
 
 &qspi_clk {
diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
index 8011c5f..e3e8610 100644
--- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
@@ -75,6 +75,11 @@
 			reg = <0x0 0x80900000 0x0 0x200000>;
 			no-map;
 		};
+
+		wlan_fw_mem: memory@93900000 {
+			reg = <0 0x93900000 0 0x200000>;
+			no-map;
+		};
 	};
 
 	cpus {
@@ -1490,6 +1495,28 @@
 
 			#freq-domain-cells = <1>;
 		};
+
+		wifi: wifi@18800000 {
+			compatible = "qcom,wcn3990-wifi";
+			reg = <0 0x18800000 0 0x800000>;
+			reg-names = "membase";
+			iommus = <&apps_smmu 0xc0 0x1>;
+			interrupts =
+				<GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH /* CE0 */ >,
+				<GIC_SPI 415 IRQ_TYPE_LEVEL_HIGH /* CE1 */ >,
+				<GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH /* CE2 */ >,
+				<GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH /* CE3 */ >,
+				<GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH /* CE4 */ >,
+				<GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH /* CE5 */ >,
+				<GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH /* CE6 */ >,
+				<GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH /* CE7 */ >,
+				<GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH /* CE8 */ >,
+				<GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH /* CE9 */ >,
+				<GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH /* CE10 */>,
+				<GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH /* CE11 */>;
+			memory-region = <&wlan_fw_mem>;
+			status = "disabled";
+		};
 	};
 
 	thermal-zones {
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [PATCH v6] arm64: dts: qcom: sc7180: Add WCN3990 WLAN module device node
  2020-02-04 13:18 [PATCH v6] arm64: dts: qcom: sc7180: Add WCN3990 WLAN module device node Rakesh Pillai
@ 2020-02-07  6:41 ` Sibi Sankar
  2020-03-24 17:39 ` Evan Green
  1 sibling, 0 replies; 6+ messages in thread
From: Sibi Sankar @ 2020-02-07  6:41 UTC (permalink / raw)
  To: Rakesh Pillai
  Cc: devicetree, linux-arm-msm-owner, linux-kernel, linux-arm-kernel,
	linux-arm-msm

Hey Rakesh,

On 2020-02-04 18:48, Rakesh Pillai wrote:
> Add device node for the ath10k SNOC platform driver probe
> and add resources required for WCN3990 on sc7180 soc.
> 
> Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
> ---
>  arch/arm64/boot/dts/qcom/sc7180-idp.dts |  5 +++++
>  arch/arm64/boot/dts/qcom/sc7180.dtsi    | 27 
> +++++++++++++++++++++++++++
>  2 files changed, 32 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> index 388f50a..167f68ac 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> +++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> @@ -287,6 +287,11 @@
>  	vdda-pll-supply = <&vreg_l4a_0p8>;
>  };
> 
> +&wifi {
> +	status = "okay";

I can see that wlan needs to
add the SIDs 0xc2, 0xc3 as well.
Without that I expect wlan will
not come up.

> +	qcom,msa-fixed-perm;

are you sure this is required when
used in conjunction with coreboot?

> +};
> +
>  /* PINCTRL - additions to nodes defined in sc7180.dtsi */
> 
>  &qspi_clk {
> diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi
> b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> index 8011c5f..e3e8610 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> @@ -75,6 +75,11 @@
>  			reg = <0x0 0x80900000 0x0 0x200000>;
>  			no-map;
>  		};
> +
> +		wlan_fw_mem: memory@93900000 {
> +			reg = <0 0x93900000 0 0x200000>;
> +			no-map;
> +		};
>  	};
> 
>  	cpus {
> @@ -1490,6 +1495,28 @@
> 
>  			#freq-domain-cells = <1>;
>  		};
> +
> +		wifi: wifi@18800000 {
> +			compatible = "qcom,wcn3990-wifi";
> +			reg = <0 0x18800000 0 0x800000>;
> +			reg-names = "membase";
> +			iommus = <&apps_smmu 0xc0 0x1>;
> +			interrupts =
> +				<GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH /* CE0 */ >,
> +				<GIC_SPI 415 IRQ_TYPE_LEVEL_HIGH /* CE1 */ >,
> +				<GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH /* CE2 */ >,
> +				<GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH /* CE3 */ >,
> +				<GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH /* CE4 */ >,
> +				<GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH /* CE5 */ >,
> +				<GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH /* CE6 */ >,
> +				<GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH /* CE7 */ >,
> +				<GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH /* CE8 */ >,
> +				<GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH /* CE9 */ >,
> +				<GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH /* CE10 */>,
> +				<GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH /* CE11 */>;
> +			memory-region = <&wlan_fw_mem>;
> +			status = "disabled";
> +		};
>  	};
> 
>  	thermal-zones {

-- 
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project.

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [PATCH v6] arm64: dts: qcom: sc7180: Add WCN3990 WLAN module device node
  2020-02-04 13:18 [PATCH v6] arm64: dts: qcom: sc7180: Add WCN3990 WLAN module device node Rakesh Pillai
  2020-02-07  6:41 ` Sibi Sankar
@ 2020-03-24 17:39 ` Evan Green
  2020-03-25 11:04   ` pillair
  1 sibling, 1 reply; 6+ messages in thread
From: Evan Green @ 2020-03-24 17:39 UTC (permalink / raw)
  To: Rakesh Pillai
  Cc: open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS, LKML,
	linux-arm Mailing List, linux-arm-msm

Hi Rakesh,

On Tue, Feb 4, 2020 at 5:21 AM Rakesh Pillai <pillair@codeaurora.org> wrote:
>
> Add device node for the ath10k SNOC platform driver probe
> and add resources required for WCN3990 on sc7180 soc.
>
> Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>

What is the status of this? Looks like you have some feedback from
Sibi. Can you reply and spin this? Also a comment below:

> ---
>  arch/arm64/boot/dts/qcom/sc7180-idp.dts |  5 +++++
>  arch/arm64/boot/dts/qcom/sc7180.dtsi    | 27 +++++++++++++++++++++++++++
>  2 files changed, 32 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> index 388f50a..167f68ac 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> +++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> @@ -287,6 +287,11 @@
>         vdda-pll-supply = <&vreg_l4a_0p8>;
>  };
>
> +&wifi {
> +       status = "okay";
> +       qcom,msa-fixed-perm;
> +};
> +
>  /* PINCTRL - additions to nodes defined in sc7180.dtsi */
>
>  &qspi_clk {
> diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> index 8011c5f..e3e8610 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> @@ -75,6 +75,11 @@
>                         reg = <0x0 0x80900000 0x0 0x200000>;
>                         no-map;
>                 };
> +
> +               wlan_fw_mem: memory@93900000 {
> +                       reg = <0 0x93900000 0 0x200000>;
> +                       no-map;
> +               };
>         };
>
>         cpus {
> @@ -1490,6 +1495,28 @@
>
>                         #freq-domain-cells = <1>;
>                 };
> +
> +               wifi: wifi@18800000 {
> +                       compatible = "qcom,wcn3990-wifi";
> +                       reg = <0 0x18800000 0 0x800000>;
> +                       reg-names = "membase";
> +                       iommus = <&apps_smmu 0xc0 0x1>;
> +                       interrupts =
> +                               <GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH /* CE0 */ >,
> +                               <GIC_SPI 415 IRQ_TYPE_LEVEL_HIGH /* CE1 */ >,
> +                               <GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH /* CE2 */ >,
> +                               <GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH /* CE3 */ >,
> +                               <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH /* CE4 */ >,
> +                               <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH /* CE5 */ >,
> +                               <GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH /* CE6 */ >,
> +                               <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH /* CE7 */ >,
> +                               <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH /* CE8 */ >,
> +                               <GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH /* CE9 */ >,
> +                               <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH /* CE10 */>,
> +                               <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH /* CE11 */>;
> +                       memory-region = <&wlan_fw_mem>;

The clocks are missing:

clocks = <&rpmhcc RPMH_RF_CLK2>;
clock-names = "cxo_ref_clk_pin";

> +                       status = "disabled";
> +               };
>         };
>
>         thermal-zones {
> --
> 2.7.4
>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 6+ messages in thread

* RE: [PATCH v6] arm64: dts: qcom: sc7180: Add WCN3990 WLAN module device node
  2020-03-24 17:39 ` Evan Green
@ 2020-03-25 11:04   ` pillair
  2020-03-25 16:03     ` Evan Green
  0 siblings, 1 reply; 6+ messages in thread
From: pillair @ 2020-03-25 11:04 UTC (permalink / raw)
  To: 'Evan Green'
  Cc: 'open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE
	BINDINGS', 'LKML', 'linux-arm Mailing List',
	'linux-arm-msm'

Hi Evan,

I will send out a v7 for this patchset.
Since I have to configure the S2 SIDs, it is dependent on below ath10k patchset.
https://patchwork.kernel.org/project/linux-wireless/list/?series=261367

Thanks,
Rakesh Pillai.

> -----Original Message-----
> From: Evan Green <evgreen@chromium.org>
> Sent: Tuesday, March 24, 2020 11:10 PM
> To: Rakesh Pillai <pillair@codeaurora.org>
> Cc: open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS
> <devicetree@vger.kernel.org>; linux-arm Mailing List <linux-arm-
> kernel@lists.infradead.org>; LKML <linux-kernel@vger.kernel.org>; linux-
> arm-msm <linux-arm-msm@vger.kernel.org>
> Subject: Re: [PATCH v6] arm64: dts: qcom: sc7180: Add WCN3990 WLAN
> module device node
> 
> Hi Rakesh,
> 
> On Tue, Feb 4, 2020 at 5:21 AM Rakesh Pillai <pillair@codeaurora.org> wrote:
> >
> > Add device node for the ath10k SNOC platform driver probe
> > and add resources required for WCN3990 on sc7180 soc.
> >
> > Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
> 
> What is the status of this? Looks like you have some feedback from
> Sibi. Can you reply and spin this? Also a comment below:
> 
> > ---
> >  arch/arm64/boot/dts/qcom/sc7180-idp.dts |  5 +++++
> >  arch/arm64/boot/dts/qcom/sc7180.dtsi    | 27
> +++++++++++++++++++++++++++
> >  2 files changed, 32 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> > index 388f50a..167f68ac 100644
> > --- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> > +++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> > @@ -287,6 +287,11 @@
> >         vdda-pll-supply = <&vreg_l4a_0p8>;
> >  };
> >
> > +&wifi {
> > +       status = "okay";
> > +       qcom,msa-fixed-perm;
> > +};
> > +
> >  /* PINCTRL - additions to nodes defined in sc7180.dtsi */
> >
> >  &qspi_clk {
> > diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi
> b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> > index 8011c5f..e3e8610 100644
> > --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> > @@ -75,6 +75,11 @@
> >                         reg = <0x0 0x80900000 0x0 0x200000>;
> >                         no-map;
> >                 };
> > +
> > +               wlan_fw_mem: memory@93900000 {
> > +                       reg = <0 0x93900000 0 0x200000>;
> > +                       no-map;
> > +               };
> >         };
> >
> >         cpus {
> > @@ -1490,6 +1495,28 @@
> >
> >                         #freq-domain-cells = <1>;
> >                 };
> > +
> > +               wifi: wifi@18800000 {
> > +                       compatible = "qcom,wcn3990-wifi";
> > +                       reg = <0 0x18800000 0 0x800000>;
> > +                       reg-names = "membase";
> > +                       iommus = <&apps_smmu 0xc0 0x1>;
> > +                       interrupts =
> > +                               <GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH /* CE0 */ >,
> > +                               <GIC_SPI 415 IRQ_TYPE_LEVEL_HIGH /* CE1 */ >,
> > +                               <GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH /* CE2 */ >,
> > +                               <GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH /* CE3 */ >,
> > +                               <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH /* CE4 */ >,
> > +                               <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH /* CE5 */ >,
> > +                               <GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH /* CE6 */ >,
> > +                               <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH /* CE7 */ >,
> > +                               <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH /* CE8 */ >,
> > +                               <GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH /* CE9 */ >,
> > +                               <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH /* CE10 */>,
> > +                               <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH /* CE11 */>;
> > +                       memory-region = <&wlan_fw_mem>;
> 
> The clocks are missing:
> 
> clocks = <&rpmhcc RPMH_RF_CLK2>;
> clock-names = "cxo_ref_clk_pin";
> 
> > +                       status = "disabled";
> > +               };
> >         };
> >
> >         thermal-zones {
> > --
> > 2.7.4
> >

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [PATCH v6] arm64: dts: qcom: sc7180: Add WCN3990 WLAN module device node
  2020-03-25 11:04   ` pillair
@ 2020-03-25 16:03     ` Evan Green
  2020-03-26 11:23       ` pillair
  0 siblings, 1 reply; 6+ messages in thread
From: Evan Green @ 2020-03-25 16:03 UTC (permalink / raw)
  To: pillair
  Cc: open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS, LKML,
	linux-arm Mailing List, linux-arm-msm

On Wed, Mar 25, 2020 at 4:05 AM <pillair@codeaurora.org> wrote:
>
> Hi Evan,
>
> I will send out a v7 for this patchset.
> Since I have to configure the S2 SIDs, it is dependent on below ath10k patchset.
> https://patchwork.kernel.org/project/linux-wireless/list/?series=261367

Ah, right. Thanks for the info, I'll check out that series as well.
-Evan

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 6+ messages in thread

* RE: [PATCH v6] arm64: dts: qcom: sc7180: Add WCN3990 WLAN module device node
  2020-03-25 16:03     ` Evan Green
@ 2020-03-26 11:23       ` pillair
  0 siblings, 0 replies; 6+ messages in thread
From: pillair @ 2020-03-26 11:23 UTC (permalink / raw)
  To: 'Evan Green'
  Cc: 'open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE
	BINDINGS', 'LKML', 'linux-arm Mailing List',
	'linux-arm-msm'

Hi Evan,

I have sent out the v7 patch by marking a dependency on the below mentioned series
https://patchwork.kernel.org/project/linux-wireless/list/?series=261367 

> The clocks are missing:
> clocks = <&rpmhcc RPMH_RF_CLK2>;
> clock-names = "cxo_ref_clk_pin";
These clocks are optional and were required for older firmware.
It's not needed now.

Thanks,
Rakesh Pillai

> -----Original Message-----
> From: Evan Green <evgreen@chromium.org>
> Sent: Wednesday, March 25, 2020 9:34 PM
> To: pillair@codeaurora.org
> Cc: open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS
> <devicetree@vger.kernel.org>; linux-arm Mailing List <linux-arm-
> kernel@lists.infradead.org>; LKML <linux-kernel@vger.kernel.org>; linux-
> arm-msm <linux-arm-msm@vger.kernel.org>
> Subject: Re: [PATCH v6] arm64: dts: qcom: sc7180: Add WCN3990 WLAN
> module device node
> 
> On Wed, Mar 25, 2020 at 4:05 AM <pillair@codeaurora.org> wrote:
> >
> > Hi Evan,
> >
> > I will send out a v7 for this patchset.
> > Since I have to configure the S2 SIDs, it is dependent on below ath10k
> patchset.
> > https://patchwork.kernel.org/project/linux-wireless/list/?series=261367
> 
> Ah, right. Thanks for the info, I'll check out that series as well.
> -Evan

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 6+ messages in thread

end of thread, back to index

Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-02-04 13:18 [PATCH v6] arm64: dts: qcom: sc7180: Add WCN3990 WLAN module device node Rakesh Pillai
2020-02-07  6:41 ` Sibi Sankar
2020-03-24 17:39 ` Evan Green
2020-03-25 11:04   ` pillair
2020-03-25 16:03     ` Evan Green
2020-03-26 11:23       ` pillair

Linux-ARM-Kernel Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-arm-kernel/0 linux-arm-kernel/git/0.git
	git clone --mirror https://lore.kernel.org/linux-arm-kernel/1 linux-arm-kernel/git/1.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-arm-kernel linux-arm-kernel/ https://lore.kernel.org/linux-arm-kernel \
		linux-arm-kernel@lists.infradead.org
	public-inbox-index linux-arm-kernel

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.infradead.lists.linux-arm-kernel


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git