[PATCH] Revert "ARM: bcm283x: Switch V3D over to using the PM driver instead of firmware."

[PATCH] Revert "ARM: bcm283x: Switch V3D over to using the PM driver instead of firmware."

[Stefan Wahren]

Since release of the new BCM2835 PM driver there has been several reports
of V3D probing issues. This is caused by timeouts during powering-up the
GRAFX PM domain:

  bcm2835-power: Timeout waiting for grafx power OK

I was able to reproduce this reliable on my Raspberry Pi 3B+ after setting
force_turbo=1 in the firmware configuration. Since there are no issues
using the firmware PM driver with the same setup, there must be an issue
in the BCM2835 PM driver.

Unfortunately there hasn't been much progress in identifying the root cause
since June (mostly in the lack of documentation), so i decided to switch
back until the issue in the BCM2835 PM driver is fixed.

Link: https://github.com/raspberrypi/linux/issues/3046
Fixes: e1dc2b2e1bef (" ARM: bcm283x: Switch V3D over to using the PM driver instead of firmware.")
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
---
 arch/arm/boot/dts/bcm2835-rpi.dtsi | 4 ++++
 arch/arm/boot/dts/bcm283x.dtsi     | 4 +---
 2 files changed, 5 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/bcm2835-rpi.dtsi b/arch/arm/boot/dts/bcm2835-rpi.dtsi
index 6c6a7f6..b909e3b 100644
--- a/arch/arm/boot/dts/bcm2835-rpi.dtsi
+++ b/arch/arm/boot/dts/bcm2835-rpi.dtsi
@@ -67,6 +67,10 @@
 	power-domains = <&power RPI_POWER_DOMAIN_USB>;
 };

+&v3d {
+	power-domains = <&power RPI_POWER_DOMAIN_V3D>;
+};
+
 &vec {
 	power-domains = <&power RPI_POWER_DOMAIN_VEC>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
index 2d191fc..b238567 100644
--- a/arch/arm/boot/dts/bcm283x.dtsi
+++ b/arch/arm/boot/dts/bcm283x.dtsi
@@ -3,7 +3,6 @@
 #include <dt-bindings/clock/bcm2835-aux.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/soc/bcm2835-pm.h>

 /* firmware-provided startup stubs live here, where the secondary CPUs are
  * spinning.
@@ -121,7 +120,7 @@
 			#interrupt-cells = <2>;
 		};

-		pm: watchdog@7e100000 {
+		watchdog@7e100000 {
 			compatible = "brcm,bcm2835-pm", "brcm,bcm2835-pm-wdt";
 			#power-domain-cells = <1>;
 			#reset-cells = <1>;
@@ -641,7 +640,6 @@
 			compatible = "brcm,bcm2835-v3d";
 			reg = <0x7ec00000 0x1000>;
 			interrupts = <1 10>;
-			power-domains = <&pm BCM2835_POWER_DOMAIN_GRAFX_V3D>;
 		};

 		vc4: gpu {
--
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH] Revert "ARM: bcm283x: Switch V3D over to using the PM driver instead of firmware."

[Eric Anholt]

[-- Attachment #1.1: Type: text/plain, Size: 1190 bytes --]

Stefan Wahren <wahrenst@gmx.net> writes:

> Since release of the new BCM2835 PM driver there has been several reports
> of V3D probing issues. This is caused by timeouts during powering-up the
> GRAFX PM domain:
>
>   bcm2835-power: Timeout waiting for grafx power OK
>
> I was able to reproduce this reliable on my Raspberry Pi 3B+ after setting
> force_turbo=1 in the firmware configuration. Since there are no issues
> using the firmware PM driver with the same setup, there must be an issue
> in the BCM2835 PM driver.
>
> Unfortunately there hasn't been much progress in identifying the root cause
> since June (mostly in the lack of documentation), so i decided to switch
> back until the issue in the BCM2835 PM driver is fixed.
>
> Link: https://github.com/raspberrypi/linux/issues/3046
> Fixes: e1dc2b2e1bef (" ARM: bcm283x: Switch V3D over to using the PM driver instead of firmware.")
> Cc: stable@vger.kernel.org
> Signed-off-by: Stefan Wahren <wahrenst@gmx.net>

Acked-by: Eric Anholt <eric@anholt.net>

I wish someone with firmware source had the time to look into why using
open source drivers to drive this hardware was failing, but I don't have
that time or code any more.

[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 832 bytes --]

[-- Attachment #2: Type: text/plain, Size: 176 bytes --]

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH] Revert "ARM: bcm283x: Switch V3D over to using the PM driver instead of firmware."

[Florian Fainelli]

On 9/8/19 8:44 AM, Stefan Wahren wrote:
> Since release of the new BCM2835 PM driver there has been several reports
> of V3D probing issues. This is caused by timeouts during powering-up the
> GRAFX PM domain:
> 
>   bcm2835-power: Timeout waiting for grafx power OK
> 
> I was able to reproduce this reliable on my Raspberry Pi 3B+ after setting
> force_turbo=1 in the firmware configuration. Since there are no issues
> using the firmware PM driver with the same setup, there must be an issue
> in the BCM2835 PM driver.
> 
> Unfortunately there hasn't been much progress in identifying the root cause
> since June (mostly in the lack of documentation), so i decided to switch
> back until the issue in the BCM2835 PM driver is fixed.
> 
> Link: https://github.com/raspberrypi/linux/issues/3046
> Fixes: e1dc2b2e1bef (" ARM: bcm283x: Switch V3D over to using the PM driver instead of firmware.")
> Cc: stable@vger.kernel.org
> Signed-off-by: Stefan Wahren <wahrenst@gmx.net>

Do you want me to pick up this change directly, or would you want to
issue a pull request for 5.4-rcX with other fixes?
-- 
Florian

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH] Revert "ARM: bcm283x: Switch V3D over to using the PM driver instead of firmware."

[Stefan Wahren]

Hi Florian,

Am 20.09.19 um 19:52 schrieb Florian Fainelli:
> On 9/8/19 8:44 AM, Stefan Wahren wrote:
>> Since release of the new BCM2835 PM driver there has been several reports
>> of V3D probing issues. This is caused by timeouts during powering-up the
>> GRAFX PM domain:
>>
>>   bcm2835-power: Timeout waiting for grafx power OK
>>
>> I was able to reproduce this reliable on my Raspberry Pi 3B+ after setting
>> force_turbo=1 in the firmware configuration. Since there are no issues
>> using the firmware PM driver with the same setup, there must be an issue
>> in the BCM2835 PM driver.
>>
>> Unfortunately there hasn't been much progress in identifying the root cause
>> since June (mostly in the lack of documentation), so i decided to switch
>> back until the issue in the BCM2835 PM driver is fixed.
>>
>> Link: https://github.com/raspberrypi/linux/issues/3046
>> Fixes: e1dc2b2e1bef (" ARM: bcm283x: Switch V3D over to using the PM driver instead of firmware.")
>> Cc: stable@vger.kernel.org
>> Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
> Do you want me to pick up this change directly, or would you want to
> issue a pull request for 5.4-rcX with other fixes?

there aren't any other fixes, please pick up this directly.

Thanks

Stefan


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH] Revert "ARM: bcm283x: Switch V3D over to using the PM driver instead of firmware."

[Florian Fainelli]

On 9/8/2019 8:44 AM, Stefan Wahren wrote:
> Since release of the new BCM2835 PM driver there has been several reports
> of V3D probing issues. This is caused by timeouts during powering-up the
> GRAFX PM domain:
> 
>   bcm2835-power: Timeout waiting for grafx power OK
> 
> I was able to reproduce this reliable on my Raspberry Pi 3B+ after setting
> force_turbo=1 in the firmware configuration. Since there are no issues
> using the firmware PM driver with the same setup, there must be an issue
> in the BCM2835 PM driver.
> 
> Unfortunately there hasn't been much progress in identifying the root cause
> since June (mostly in the lack of documentation), so i decided to switch
> back until the issue in the BCM2835 PM driver is fixed.
> 
> Link: https://github.com/raspberrypi/linux/issues/3046
> Fixes: e1dc2b2e1bef (" ARM: bcm283x: Switch V3D over to using the PM driver instead of firmware.")
> Cc: stable@vger.kernel.org
> Signed-off-by: Stefan Wahren <wahrenst@gmx.net>

Applied to devicetree/fixes, thanks!
-- 
Florian

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH] Revert "ARM: bcm283x: Switch V3D over to using the PM driver instead of firmware."

[Stefan Wahren]

Hi Florian,

Am 23.09.19 um 20:56 schrieb Florian Fainelli:
>
> On 9/8/2019 8:44 AM, Stefan Wahren wrote:
>> Since release of the new BCM2835 PM driver there has been several reports
>> of V3D probing issues. This is caused by timeouts during powering-up the
>> GRAFX PM domain:
>>
>>   bcm2835-power: Timeout waiting for grafx power OK
>>
>> I was able to reproduce this reliable on my Raspberry Pi 3B+ after setting
>> force_turbo=1 in the firmware configuration. Since there are no issues
>> using the firmware PM driver with the same setup, there must be an issue
>> in the BCM2835 PM driver.
>>
>> Unfortunately there hasn't been much progress in identifying the root cause
>> since June (mostly in the lack of documentation), so i decided to switch
>> back until the issue in the BCM2835 PM driver is fixed.
>>
>> Link: https://github.com/raspberrypi/linux/issues/3046
>> Fixes: e1dc2b2e1bef (" ARM: bcm283x: Switch V3D over to using the PM driver instead of firmware.")
>> Cc: stable@vger.kernel.org
>> Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
> Applied to devicetree/fixes, thanks!

i noticed that X hangs with recent Raspbian and Linux 5.4-rc2 after this
revert has been applied.

Is there a chance to drop the revert?

Stefan


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH] Revert "ARM: bcm283x: Switch V3D over to using the PM driver instead of firmware."

[Florian Fainelli]

On 10/9/19 2:33 PM, Stefan Wahren wrote:
> Hi Florian,
> 
> Am 23.09.19 um 20:56 schrieb Florian Fainelli:
>>
>> On 9/8/2019 8:44 AM, Stefan Wahren wrote:
>>> Since release of the new BCM2835 PM driver there has been several reports
>>> of V3D probing issues. This is caused by timeouts during powering-up the
>>> GRAFX PM domain:
>>>
>>>   bcm2835-power: Timeout waiting for grafx power OK
>>>
>>> I was able to reproduce this reliable on my Raspberry Pi 3B+ after setting
>>> force_turbo=1 in the firmware configuration. Since there are no issues
>>> using the firmware PM driver with the same setup, there must be an issue
>>> in the BCM2835 PM driver.
>>>
>>> Unfortunately there hasn't been much progress in identifying the root cause
>>> since June (mostly in the lack of documentation), so i decided to switch
>>> back until the issue in the BCM2835 PM driver is fixed.
>>>
>>> Link: https://github.com/raspberrypi/linux/issues/3046
>>> Fixes: e1dc2b2e1bef (" ARM: bcm283x: Switch V3D over to using the PM driver instead of firmware.")
>>> Cc: stable@vger.kernel.org
>>> Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
>> Applied to devicetree/fixes, thanks!
> 
> i noticed that X hangs with recent Raspbian and Linux 5.4-rc2 after this
> revert has been applied.
> 
> Is there a chance to drop the revert?

I have not sent anything yet as I wanted to get some testing done on
other platforms, so yes, I can definitively drop that particular changes
from devicetree/fixes and not send it for a 5.4-rc3 pull request. Does
that work for you?
-- 
Florian

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH] Revert "ARM: bcm283x: Switch V3D over to using the PM driver instead of firmware."

[Stefan Wahren]

On 09.10.19 23:42, Florian Fainelli wrote:
> On 10/9/19 2:33 PM, Stefan Wahren wrote:
>> Hi Florian,
>>
>> Am 23.09.19 um 20:56 schrieb Florian Fainelli:
>>> On 9/8/2019 8:44 AM, Stefan Wahren wrote:
>>>> Since release of the new BCM2835 PM driver there has been several reports
>>>> of V3D probing issues. This is caused by timeouts during powering-up the
>>>> GRAFX PM domain:
>>>>
>>>>   bcm2835-power: Timeout waiting for grafx power OK
>>>>
>>>> I was able to reproduce this reliable on my Raspberry Pi 3B+ after setting
>>>> force_turbo=1 in the firmware configuration. Since there are no issues
>>>> using the firmware PM driver with the same setup, there must be an issue
>>>> in the BCM2835 PM driver.
>>>>
>>>> Unfortunately there hasn't been much progress in identifying the root cause
>>>> since June (mostly in the lack of documentation), so i decided to switch
>>>> back until the issue in the BCM2835 PM driver is fixed.
>>>>
>>>> Link: https://github.com/raspberrypi/linux/issues/3046
>>>> Fixes: e1dc2b2e1bef (" ARM: bcm283x: Switch V3D over to using the PM driver instead of firmware.")
>>>> Cc: stable@vger.kernel.org
>>>> Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
>>> Applied to devicetree/fixes, thanks!
>> i noticed that X hangs with recent Raspbian and Linux 5.4-rc2 after this
>> revert has been applied.
>>
>> Is there a chance to drop the revert?
> I have not sent anything yet as I wanted to get some testing done on
> other platforms, so yes, I can definitively drop that particular changes
> from devicetree/fixes and not send it for a 5.4-rc3 pull request. Does
> that work for you?

Yes, definitely

Thanks Stefan


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel