linux-arm-kernel.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
From: ard.biesheuvel@linaro.org (Ard Biesheuvel)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v2] arm64/efi: efistub: jump to 'stext' directly, not through the header
Date: Tue, 15 Jul 2014 12:58:06 +0200	[thread overview]
Message-ID: <1405421886-11692-1-git-send-email-ard.biesheuvel@linaro.org> (raw)

After the EFI stub has done its business, it jumps into the kernel by branching
to offset #0 of the loaded Image, which is where it expects to find the header
containing a 'branch to stext' instruction.

However, the header is not covered by any PE/COFF section, so the header may
not actually be loaded at the expected offset. So instead, jump to 'stext'
directly, which is at the base of the PE/COFF .text section, by supplying a
symbol 'stext_offset' to efi-entry.o which contains the relative offset of
stext into the Image. Also replace other open coded calculations of the same
value with a reference to 'stext_offset'

Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
---
 arch/arm64/kernel/efi-entry.S |  3 ++-
 arch/arm64/kernel/head.S      | 10 ++++++----
 2 files changed, 8 insertions(+), 5 deletions(-)

diff --git a/arch/arm64/kernel/efi-entry.S b/arch/arm64/kernel/efi-entry.S
index 619b1dd7bcde..a0016d3a17da 100644
--- a/arch/arm64/kernel/efi-entry.S
+++ b/arch/arm64/kernel/efi-entry.S
@@ -61,7 +61,8 @@ ENTRY(efi_stub_entry)
 	 */
 	mov	x20, x0		// DTB address
 	ldr	x0, [sp, #16]	// relocated _text address
-	mov	x21, x0
+	ldr	x21, =stext_offset
+	add	x21, x0, x21
 
 	/*
 	 * Flush dcache covering current runtime addresses
diff --git a/arch/arm64/kernel/head.S b/arch/arm64/kernel/head.S
index a2c1195abb7f..78ddae28b090 100644
--- a/arch/arm64/kernel/head.S
+++ b/arch/arm64/kernel/head.S
@@ -137,6 +137,8 @@ efi_head:
 #endif
 
 #ifdef CONFIG_EFI
+	.globl	stext_offset
+	.set	stext_offset, stext - efi_head
 	.align 3
 pe_header:
 	.ascii	"PE"
@@ -160,7 +162,7 @@ optional_header:
 	.long	0				// SizeOfInitializedData
 	.long	0				// SizeOfUninitializedData
 	.long	efi_stub_entry - efi_head	// AddressOfEntryPoint
-	.long	stext - efi_head		// BaseOfCode
+	.long	stext_offset			// BaseOfCode
 
 extra_header_fields:
 	.quad	0				// ImageBase
@@ -177,7 +179,7 @@ extra_header_fields:
 	.long	_edata - efi_head		// SizeOfImage
 
 	// Everything before the kernel image is considered part of the header
-	.long	stext - efi_head		// SizeOfHeaders
+	.long	stext_offset			// SizeOfHeaders
 	.long	0				// CheckSum
 	.short	0xa				// Subsystem (EFI application)
 	.short	0				// DllCharacteristics
@@ -222,9 +224,9 @@ section_table:
 	.byte	0
 	.byte	0        		// end of 0 padding of section name
 	.long	_edata - stext		// VirtualSize
-	.long	stext - efi_head	// VirtualAddress
+	.long	stext_offset		// VirtualAddress
 	.long	_edata - stext		// SizeOfRawData
-	.long	stext - efi_head	// PointerToRawData
+	.long	stext_offset		// PointerToRawData
 
 	.long	0		// PointerToRelocations (0 for executables)
 	.long	0		// PointerToLineNumbers (0 for executables)
-- 
1.8.3.2

             reply	other threads:[~2014-07-15 10:58 UTC|newest]

Thread overview: 13+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2014-07-15 10:58 Ard Biesheuvel [this message]
2014-07-16 14:51 ` [PATCH v2] arm64/efi: efistub: jump to 'stext' directly, not through the header Mark Salter
2014-07-16 15:53   ` Mark Rutland
2014-07-16 19:45     ` Mark Salter
2014-07-16 20:38       ` Ard Biesheuvel
2014-07-16 21:03         ` Mark Salter
2014-07-16 21:13           ` Ard Biesheuvel
2014-07-17 14:09             ` Mark Salter
2014-07-21 16:32               ` Ard Biesheuvel
2014-10-06 18:13               ` Ard Biesheuvel
2014-10-06 19:33                 ` Peter Jones
2014-10-07  7:49                   ` Ard Biesheuvel
2014-07-16 21:03         ` Roy Franz

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1405421886-11692-1-git-send-email-ard.biesheuvel@linaro.org \
    --to=ard.biesheuvel@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).