From: bigeasy@linutronix.de (Sebastian Andrzej Siewior)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 05/18] tty: serial: 8250_core: read only RX if there is something in the FIFO
Date: Fri, 5 Sep 2014 21:02:40 +0200 [thread overview]
Message-ID: <1409943773-7874-6-git-send-email-bigeasy@linutronix.de> (raw)
In-Reply-To: <1409943773-7874-1-git-send-email-bigeasy@linutronix.de>
The serial8250_do_startup() function unconditionally clears the
interrupts and for that it reads from the RX-FIFO without checking if
there is a byte in the FIFO or not. This works fine on OMAP4+ HW like
AM335x or DRA7.
OMAP3630 ES1.1 (which means probably all OMAP3 and earlier) does not like
this:
|Unhandled fault: external abort on non-linefetch (0x1028) at 0xfb020000
|Internal error: : 1028 [#1] ARM
|Modules linked in:
|CPU: 0 PID: 1 Comm: swapper Not tainted 3.16.0-00022-g7edcb57-dirty #1213
|task: de0572c0 ti: de058000 task.ti: de058000
|PC is at mem32_serial_in+0xc/0x1c
|LR is at serial8250_do_startup+0x220/0x85c
|Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
|Control: 10c5387d Table: 80004019 DAC: 00000015
|[<c03051d4>] (mem32_serial_in) from [<c0307fe8>] (serial8250_do_startup+0x220/0x85c)
|[<c0307fe8>] (serial8250_do_startup) from [<c0309e00>] (omap_8250_startup+0x5c/0xe0)
|[<c0309e00>] (omap_8250_startup) from [<c030863c>] (serial8250_startup+0x18/0x2c)
|[<c030863c>] (serial8250_startup) from [<c030394c>] (uart_startup+0x78/0x1d8)
|[<c030394c>] (uart_startup) from [<c0304678>] (uart_open+0xe8/0x114)
|[<c0304678>] (uart_open) from [<c02e9e10>] (tty_open+0x1a8/0x5a4)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
---
drivers/tty/serial/8250/8250_core.c | 11 ++++++-----
1 file changed, 6 insertions(+), 5 deletions(-)
diff --git a/drivers/tty/serial/8250/8250_core.c b/drivers/tty/serial/8250/8250_core.c
index f9dd20ebab52..eaab8974a456 100644
--- a/drivers/tty/serial/8250/8250_core.c
+++ b/drivers/tty/serial/8250/8250_core.c
@@ -2086,8 +2086,8 @@ int serial8250_do_startup(struct uart_port *port)
/*
* Clear the interrupt registers.
*/
- serial_port_in(port, UART_LSR);
- serial_port_in(port, UART_RX);
+ if (serial_port_in(port, UART_LSR) & UART_LSR_DR)
+ serial_port_in(port, UART_RX);
serial_port_in(port, UART_IIR);
serial_port_in(port, UART_MSR);
@@ -2248,8 +2248,8 @@ int serial8250_do_startup(struct uart_port *port)
* saved flags to avoid getting false values from polling
* routines or the previous session.
*/
- serial_port_in(port, UART_LSR);
- serial_port_in(port, UART_RX);
+ if (serial_port_in(port, UART_LSR) & UART_LSR_DR)
+ serial_port_in(port, UART_RX);
serial_port_in(port, UART_IIR);
serial_port_in(port, UART_MSR);
up->lsr_saved_flags = 0;
@@ -2342,7 +2342,8 @@ void serial8250_do_shutdown(struct uart_port *port)
* Read data port to reset things, and then unlink from
* the IRQ chain.
*/
- serial_port_in(port, UART_RX);
+ if (serial_port_in(port, UART_LSR) & UART_LSR_DR)
+ serial_port_in(port, UART_RX);
serial8250_rpm_put(up);
del_timer_sync(&up->timer);
--
2.1.0
next prev parent reply other threads:[~2014-09-05 19:02 UTC|newest]
Thread overview: 35+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-09-05 19:02 [PATCH v8 00/18] 8250-core based serial driver for OMAP + DMA Sebastian Andrzej Siewior
2014-09-05 19:02 ` [PATCH 01/18] tty: serial: 8250_core: provide a function to export uart_8250_port Sebastian Andrzej Siewior
2014-09-05 19:02 ` [PATCH 02/18] tty: serial: 8250_core: allow to overwrite & export serial8250_startup() Sebastian Andrzej Siewior
2014-09-05 19:02 ` [PATCH 03/18] tty: serial: 8250_core: allow to set ->throttle / ->unthrottle callbacks Sebastian Andrzej Siewior
2014-09-08 23:33 ` Greg Kroah-Hartman
2014-09-09 0:41 ` Tony Lindgren
2014-09-05 19:02 ` [PATCH 04/18] tty: serial: 8250_core: add run time pm Sebastian Andrzej Siewior
2014-09-05 19:02 ` Sebastian Andrzej Siewior [this message]
2014-09-05 19:02 ` [PATCH 06/18] tty: serial: 8250_core: user the ->line argument as a hint in serial8250_find_match_or_unused() Sebastian Andrzej Siewior
2014-09-05 19:02 ` [PATCH 07/18] tty: serial: 8250_core: remove UART_IER_RDI in serial8250_stop_rx() Sebastian Andrzej Siewior
2014-09-05 19:02 ` [PATCH 08/18] tty: serial: Add 8250-core based omap driver Sebastian Andrzej Siewior
2014-09-08 16:39 ` Tony Lindgren
2014-09-05 19:02 ` [PATCH 09/18] tty: serial: 8250_dma: handle error on TX submit Sebastian Andrzej Siewior
2014-09-05 19:02 ` [PATCH 10/18] tty: serial: 8250_dma: enqueue RX dma again on completion Sebastian Andrzej Siewior
2014-09-05 19:02 ` [PATCH 11/18] tty: serial: 8250_dma: Add a TX trigger workaround for AM33xx Sebastian Andrzej Siewior
2014-09-08 16:41 ` Tony Lindgren
2014-09-08 16:45 ` Sebastian Andrzej Siewior
2014-09-05 19:02 ` [PATCH 12/18] tty: serial: 8250_dma: optimize the xmit path due to UART_BUG_DMA_TX Sebastian Andrzej Siewior
2014-09-05 19:02 ` [PATCH 13/18] tty: serial: 8250_dma: keep own book keeping about RX transfers Sebastian Andrzej Siewior
2014-09-05 19:02 ` [PATCH 14/18] tty: serial: 8250_dma: handle the when UART response while DMA remains idle Sebastian Andrzej Siewior
2014-09-05 19:02 ` [PATCH 15/18] tty: serial: 8250_dma: add pm runtime Sebastian Andrzej Siewior
2014-09-05 19:02 ` [PATCH 16/18] arm: dts: am33xx: add DMA properties for UART Sebastian Andrzej Siewior
2014-09-05 19:02 ` [PATCH 17/18] arm: dts: dra7: " Sebastian Andrzej Siewior
2014-09-05 19:02 ` [PATCH 18/18] tty: serial: 8250: omap: add dma support Sebastian Andrzej Siewior
2014-09-08 14:46 ` [PATCH v8 00/18] 8250-core based serial driver for OMAP + DMA Frans Klaver
2014-09-08 15:15 ` Sebastian Andrzej Siewior
2014-09-08 16:33 ` Sebastian Andrzej Siewior
2014-09-08 18:25 ` Frans Klaver
2014-09-08 18:33 ` Frans Klaver
2014-09-09 19:41 ` Sebastian Andrzej Siewior
2014-09-10 14:15 ` Frans Klaver
2014-09-10 16:56 ` Sebastian Andrzej Siewior
2014-09-08 17:40 ` Tony Lindgren
2014-09-08 17:55 ` Tony Lindgren
2014-09-09 7:33 ` Sebastian Andrzej Siewior
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1409943773-7874-6-git-send-email-bigeasy@linutronix.de \
--to=bigeasy@linutronix.de \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).