linux-arm-kernel.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
From: zyw@rock-chips.com (Chris Zhong)
To: linux-arm-kernel@lists.infradead.org
Subject: [v5 PATCH 2/5] Documentation: bindings: add dt doc for Rockchip USB Type-C PHY
Date: Tue, 12 Jul 2016 23:09:45 +0800	[thread overview]
Message-ID: <1468336188-565-3-git-send-email-zyw@rock-chips.com> (raw)
In-Reply-To: <1468336188-565-1-git-send-email-zyw@rock-chips.com>

This patch adds a binding that describes the Rockchip USB Type-C PHY
for rk3399

Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>

---

Changes in v5: None
Changes in v4:
- add a #phy-cells node

Changes in v3:
- use compatible: rockchip,rk3399-typec-phy
- use dashes instead of underscores.

Changes in v2:
- add some registers description

Changes in v1:
- add extcon node description
- move the registers in phy driver
- remove the suffix of reset

 .../devicetree/bindings/phy/phy-rockchip-typec.txt | 77 ++++++++++++++++++++++
 1 file changed, 77 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt

diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt b/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt
new file mode 100644
index 0000000..b1c6ef3f
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt
@@ -0,0 +1,77 @@
+* ROCKCHIP type-c PHY
+---------------------
+
+Required properties:
+ - compatible : must be "rockchip,rk3399-typec-phy"
+ - reg: Address and length of the usb phy control register set
+ - rockchip,grf : phandle to the syscon managing the "general
+   register files"
+ - clocks : phandle + clock specifier for the phy clocks
+ - clock-names : string, clock name, must be "tcpdcore", "tcpdphy-ref";
+ - resets : a list of phandle + reset specifier pairs
+ - reset-names : string reset name, must be:
+		 "uphy", "uphy-pipe", "uphy-tcphy"
+ - extcon : extcon specifier for the Power Delivery
+ - #phy-cells: must be 0. See ./phy-bindings.txt for details.
+
+Note, there are 2 type-c phys for RK3399, and they are almost identical, except
+these registers(description below), every register node contains 3 sections:
+offset, enable bit, write mask bit.
+ - rockchip,typec-conn-dir : the register of type-c connector direction,
+   for type-c phy0, it must be <0xe580 0 16>;
+   for type-c phy1, it must be <0xe58c 0 16>;
+ - rockchip,usb3tousb2-en : the register of type-c force usb3 to usb2 enable
+   control.
+   for type-c phy0, it must be <0xe580 3 19>;
+   for type-c phy1, it must be <0xe58c 3 19>;
+ - rockchip,external-psm : the register of type-c phy external psm clock
+   selection.
+   for type-c phy0, it must be <0xe588 14 30>;
+   for type-c phy1, it must be <0xe594 14 30>;
+ - rockchip,pipe-status : the register of type-c phy pipe status.
+   for type-c phy0, it must be <0xe5c0 0 0>;
+   for type-c phy1, it must be <0xe5c0 16 16>;
+ - rockchip,uphy-dp-sel : the register of type-c phy selection for DP
+   for type-c phy0, it must be <0x6268 19 19>;
+   for type-c phy1, it must be <0x6268 3 19>;
+
+Example:
+	tcphy0: phy at ff7c0000 {
+		compatible = "rockchip,rk3399-typec-phy";
+		reg = <0x0 0xff7c0000 0x0 0x40000>;
+		rockchip,grf = <&grf>;
+		#phy-cells = <0>;
+		extcon = <&fusb0>;
+		clocks = <&cru SCLK_UPHY0_TCPDCORE>,
+			 <&cru SCLK_UPHY0_TCPDPHY_REF>;
+		clock-names = "tcpdcore", "tcpdphy-ref";
+		resets = <&cru SRST_UPHY0>,
+			 <&cru SRST_UPHY0_PIPE_L00>,
+			 <&cru SRST_P_UPHY0_TCPHY>;
+		reset-names = "uphy", "uphy-pipe", "uphy-tcphy";
+		rockchip,typec-conn-dir = <0xe580 0 16>;
+		rockchip,usb3tousb2-en = <0xe580 3 19>;
+		rockchip,external-psm = <0xe588 14 30>;
+		rockchip,pipe-status = <0xe5c0 0 0>;
+		rockchip,uphy-dp-sel = <0x6268 19 19>;
+	};
+
+	tcphy1: phy at ff800000 {
+		compatible = "rockchip,rk3399-typec-phy";
+		reg = <0x0 0xff800000 0x0 0x40000>;
+		rockchip,grf = <&grf>;
+		#phy-cells = <0>;
+		extcon = <&fusb1>;
+		clocks = <&cru SCLK_UPHY1_TCPDCORE>,
+			 <&cru SCLK_UPHY1_TCPDPHY_REF>;
+		clock-names = "tcpdcore", "tcpdphy-ref";
+		resets = <&cru SRST_UPHY1>,
+		         <&cru SRST_UPHY1_PIPE_L00>,
+			 <&cru SRST_P_UPHY1_TCPHY>;
+		reset-names = "uphy", "uphy-pipe", "uphy-tcphy";
+		rockchip,typec-conn-dir = <0xe58c 0 16>;
+		rockchip,usb3tousb2-en = <0xe58c 3 19>;
+		rockchip,external-psm = <0xe594 14 30>;
+		rockchip,pipe-status = <0xe5c0 16 16>;
+		rockchip,uphy-dp-sel = <0x6268 3 19>;
+	};
-- 
2.6.3

  reply	other threads:[~2016-07-12 15:09 UTC|newest]

Thread overview: 11+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2016-07-12 15:09 [v5 PATCH 0/5] Rockchip Type-C and DisplayPort driver Chris Zhong
2016-07-12 15:09 ` Chris Zhong [this message]
2016-07-12 15:09 ` [v5 PATCH 3/5] phy: Add USB Type-C PHY driver for rk3399 Chris Zhong
2016-07-12 15:09 ` [v5 PATCH 4/5] Documentation: bindings: add dt documentation for cdn DP controller Chris Zhong
2016-07-12 15:09 ` [v5 PATCH 5/5] drm/rockchip: cdn-dp: add cdn DP support for rk3399 Chris Zhong
2016-07-13 13:59   ` Sean Paul
2016-07-14  3:08     ` Chris Zhong
2016-07-14 14:02       ` Sean Paul
2016-07-15  5:52         ` [v5.1 " Chris Zhong
2016-07-15  8:18         ` [v5.2 " Chris Zhong
2016-07-19 16:44           ` Sean Paul

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1468336188-565-3-git-send-email-zyw@rock-chips.com \
    --to=zyw@rock-chips.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).