From mboxrd@z Thu Jan 1 00:00:00 1970 From: vivek.gautam@codeaurora.org (Vivek Gautam) Date: Wed, 5 Apr 2017 18:02:38 +0530 Subject: [PATCH V7 4/4] phy: qcom-qmp: new qmp phy driver for qcom-chipsets In-Reply-To: <1491395558-16902-1-git-send-email-vivek.gautam@codeaurora.org> References: <1491395558-16902-1-git-send-email-vivek.gautam@codeaurora.org> Message-ID: <1491395558-16902-5-git-send-email-vivek.gautam@codeaurora.org> To: linux-arm-kernel@lists.infradead.org List-Id: linux-arm-kernel.lists.infradead.org Qualcomm SOCs have QMP phy controller that provides support to a number of controller, viz. PCIe, UFS, and USB. Add a new driver, based on generic phy framework, for this phy controller. Signed-off-by: Vivek Gautam Tested-by: Srinivas Kandagatla --- Changes since v6: - Rebased on phy/next and *not* including phy grouping series. Changes since v5: - Rebased on top of phy grouping series. So the driver now sits in drivers/phy/qualcomm/ - Removed instances of readl_relaxed() and writel_relaxed(), and using readl() and writel() instead. - Replaced regulator handling with regulator_bulk() apis, so that qusb2_phy_toggle_power() method is completely dropped. - Removed memory barriers from the driver. Instead, added an extra readl() over the register in qphy_setbits() and qphy_clrbits() to ensure that the write is through to the device. - Fixed nits about return statement from probe(), phy_pipe_clk_register() and qcom_qmp_phy_create(). Changes since v4: - Added provision for child nodes representing each phy lane. Each of these nodes have their own register space for tx, rx and pcs blocks. Added provision in qcom_qmp_phy_create() to iomap these address spaces. - Added list of clocks and resets that are mandatory for each phy. qcom_qmp_phy_clk_init(), and qcom_qmp_phy_reset_init() methods request this list and maintains it with qmp. The clocks and resets are then enabled/de-asserted based on this list. This list is also updated in the binding documentation. - Removed qcom_qmp_phy_xlate() method as we don't need it with #phy-cells 0. - Removed unnecessary of_match_ptr() cast for the match table, since the driver is compiled for CONFIG_OF. - Updated copyright year to 2017. Changes since v3: - Renamed 'struct qcom_qmp_phy' to 'struct qcom_qmp' and 'struct qmp_phy_desc' to 'struct qmp_phy' to avoid any confusion in distinguishing between QMP phy block and per-lane phy which is the actual phy in Linux eyes (suggested by Bjorn Andersson). - Made error labels more idiomatic. - Modified status checking for phy pcs. - Fixed power_down_delay check. - Refactored phy_pipe_clk_register() to register the pipe clock source using devm_clk_hw_register() (suggested by Stephen). - qcom_qmp_phy_xlate() function: - Removed unnecessary 'for loop'. - Added additional check for '0' or -ve args_count. - Fixed the mixed tabs and spaces in pipe_clk_src diagram. - Removed instances of memset() since we use snprintf() for the buffers. - Refactored qphy_setbits() and qphy_clrbits() a little bit to accept base address and register offset as two separate arguments. Changes since v2: - Removed selecting 'RESET_CONTROLLER' config. - Added error handling for clk_prepare_enable paths. - Removed 'ref_clk_src' handling. Driver doesn't need to request and handle this clock. - Using readl_poll_timeout() to simplify pcs ready status polling. Also fixed the polling condition for pcs block ready status: 'Common block ready status bit is set on phy init completion, while PCS block ready status bit (PHYSTATUS) is reset on phy init completion.' - Moved out the per-lane phy creation from probe() to separate function. - Registering pipe clock source as a fixed rate clock that comes out of the PLL block of QMP phy. These source clocks serve as parent to 'pipe_clks' that are requested by pcie or usb3 phys. - Using of_device_get_match_data() to get match data. - Fixed sparse warnings for 'static' and 'const'. - Using shorter variable names in structure and in functions. - Handling various comment style shortcomings. Changes since v1: - Fixed missing mutex_unlock() calls in error cases, reported by Julia Lawall. - Selecting CONFIG_RESET_CONTROLLER when this driver is enabled. - Added a boolean property to check if the phy has individual lane reset available. - Took care or EPROBE_DEFER, dev_vdbg() and other minor nits. - Removed references to non-lkml links from commit message. - Moved to use separate iomem resources for each lanes. Tx, Rx and PCS offsets per lane can now come from dt bindings. drivers/phy/Kconfig | 8 + drivers/phy/Makefile | 1 + drivers/phy/phy-qcom-qmp.c | 1153 ++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 1162 insertions(+) create mode 100644 drivers/phy/phy-qcom-qmp.c diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig index ccc9178e32cd..bb8140355608 100644 --- a/drivers/phy/Kconfig +++ b/drivers/phy/Kconfig @@ -439,6 +439,14 @@ config PHY_STIH407_USB Enable this support to enable the picoPHY device used by USB2 and USB3 controllers on STMicroelectronics STiH407 SoC families. +config PHY_QCOM_QMP + tristate "Qualcomm QMP PHY Driver" + depends on OF && (ARCH_QCOM || COMPILE_TEST) + select GENERIC_PHY + help + Enable this to support the QMP PHY transceiver that is used + with controllers such as PCIe, UFS, and USB on Qualcomm chips. + config PHY_QCOM_QUSB2 tristate "Qualcomm QUSB2 PHY Driver" depends on OF && (ARCH_QCOM || COMPILE_TEST) diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile index 0375c6a32697..5347e6feb292 100644 --- a/drivers/phy/Makefile +++ b/drivers/phy/Makefile @@ -50,6 +50,7 @@ obj-$(CONFIG_PHY_ST_SPEAR1310_MIPHY) += phy-spear1310-miphy.o obj-$(CONFIG_PHY_ST_SPEAR1340_MIPHY) += phy-spear1340-miphy.o obj-$(CONFIG_PHY_XGENE) += phy-xgene.o obj-$(CONFIG_PHY_STIH407_USB) += phy-stih407-usb.o +obj-$(CONFIG_PHY_QCOM_QMP) += phy-qcom-qmp.o obj-$(CONFIG_PHY_QCOM_QUSB2) += phy-qcom-qusb2.o obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs.o obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs-qmp-20nm.o diff --git a/drivers/phy/phy-qcom-qmp.c b/drivers/phy/phy-qcom-qmp.c new file mode 100644 index 000000000000..153b6252b189 --- /dev/null +++ b/drivers/phy/phy-qcom-qmp.c @@ -0,0 +1,1153 @@ +/* + * Copyright (c) 2017, The Linux Foundation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include + +/* QMP PHY QSERDES COM registers */ +#define QSERDES_COM_BG_TIMER 0x00c +#define QSERDES_COM_SSC_EN_CENTER 0x010 +#define QSERDES_COM_SSC_ADJ_PER1 0x014 +#define QSERDES_COM_SSC_ADJ_PER2 0x018 +#define QSERDES_COM_SSC_PER1 0x01c +#define QSERDES_COM_SSC_PER2 0x020 +#define QSERDES_COM_SSC_STEP_SIZE1 0x024 +#define QSERDES_COM_SSC_STEP_SIZE2 0x028 +#define QSERDES_COM_BIAS_EN_CLKBUFLR_EN 0x034 +#define QSERDES_COM_CLK_ENABLE1 0x038 +#define QSERDES_COM_SYS_CLK_CTRL 0x03c +#define QSERDES_COM_SYSCLK_BUF_ENABLE 0x040 +#define QSERDES_COM_PLL_IVCO 0x048 +#define QSERDES_COM_LOCK_CMP1_MODE0 0x04c +#define QSERDES_COM_LOCK_CMP2_MODE0 0x050 +#define QSERDES_COM_LOCK_CMP3_MODE0 0x054 +#define QSERDES_COM_LOCK_CMP1_MODE1 0x058 +#define QSERDES_COM_LOCK_CMP2_MODE1 0x05c +#define QSERDES_COM_LOCK_CMP3_MODE1 0x060 +#define QSERDES_COM_BG_TRIM 0x070 +#define QSERDES_COM_CLK_EP_DIV 0x074 +#define QSERDES_COM_CP_CTRL_MODE0 0x078 +#define QSERDES_COM_CP_CTRL_MODE1 0x07c +#define QSERDES_COM_PLL_RCTRL_MODE0 0x084 +#define QSERDES_COM_PLL_RCTRL_MODE1 0x088 +#define QSERDES_COM_PLL_CCTRL_MODE0 0x090 +#define QSERDES_COM_PLL_CCTRL_MODE1 0x094 +#define QSERDES_COM_SYSCLK_EN_SEL 0x0ac +#define QSERDES_COM_RESETSM_CNTRL 0x0b4 +#define QSERDES_COM_RESTRIM_CTRL 0x0bc +#define QSERDES_COM_RESCODE_DIV_NUM 0x0c4 +#define QSERDES_COM_LOCK_CMP_EN 0x0c8 +#define QSERDES_COM_LOCK_CMP_CFG 0x0cc +#define QSERDES_COM_DEC_START_MODE0 0x0d0 +#define QSERDES_COM_DEC_START_MODE1 0x0d4 +#define QSERDES_COM_DIV_FRAC_START1_MODE0 0x0dc +#define QSERDES_COM_DIV_FRAC_START2_MODE0 0x0e0 +#define QSERDES_COM_DIV_FRAC_START3_MODE0 0x0e4 +#define QSERDES_COM_DIV_FRAC_START1_MODE1 0x0e8 +#define QSERDES_COM_DIV_FRAC_START2_MODE1 0x0ec +#define QSERDES_COM_DIV_FRAC_START3_MODE1 0x0f0 +#define QSERDES_COM_INTEGLOOP_GAIN0_MODE0 0x108 +#define QSERDES_COM_INTEGLOOP_GAIN1_MODE0 0x10c +#define QSERDES_COM_INTEGLOOP_GAIN0_MODE1 0x110 +#define QSERDES_COM_INTEGLOOP_GAIN1_MODE1 0x114 +#define QSERDES_COM_VCO_TUNE_CTRL 0x124 +#define QSERDES_COM_VCO_TUNE_MAP 0x128 +#define QSERDES_COM_VCO_TUNE1_MODE0 0x12c +#define QSERDES_COM_VCO_TUNE2_MODE0 0x130 +#define QSERDES_COM_VCO_TUNE1_MODE1 0x134 +#define QSERDES_COM_VCO_TUNE2_MODE1 0x138 +#define QSERDES_COM_VCO_TUNE_TIMER1 0x144 +#define QSERDES_COM_VCO_TUNE_TIMER2 0x148 +#define QSERDES_COM_BG_CTRL 0x170 +#define QSERDES_COM_CLK_SELECT 0x174 +#define QSERDES_COM_HSCLK_SEL 0x178 +#define QSERDES_COM_CORECLK_DIV 0x184 +#define QSERDES_COM_CORE_CLK_EN 0x18c +#define QSERDES_COM_C_READY_STATUS 0x190 +#define QSERDES_COM_CMN_CONFIG 0x194 +#define QSERDES_COM_SVS_MODE_CLK_SEL 0x19c +#define QSERDES_COM_DEBUG_BUS0 0x1a0 +#define QSERDES_COM_DEBUG_BUS1 0x1a4 +#define QSERDES_COM_DEBUG_BUS2 0x1a8 +#define QSERDES_COM_DEBUG_BUS3 0x1ac +#define QSERDES_COM_DEBUG_BUS_SEL 0x1b0 +#define QSERDES_COM_CORECLK_DIV_MODE1 0x1bc + +/* QMP PHY TX registers */ +#define QSERDES_TX_RES_CODE_LANE_OFFSET 0x054 +#define QSERDES_TX_DEBUG_BUS_SEL 0x064 +#define QSERDES_TX_HIGHZ_TRANSCEIVEREN_BIAS_DRVR_EN 0x068 +#define QSERDES_TX_LANE_MODE 0x094 +#define QSERDES_TX_RCV_DETECT_LVL_2 0x0ac + +/* QMP PHY RX registers */ +#define QSERDES_RX_UCDR_SO_GAIN_HALF 0x010 +#define QSERDES_RX_UCDR_SO_GAIN 0x01c +#define QSERDES_RX_UCDR_FASTLOCK_FO_GAIN 0x040 +#define QSERDES_RX_UCDR_SO_SATURATION_AND_ENABLE 0x048 +#define QSERDES_RX_RX_TERM_BW 0x090 +#define QSERDES_RX_RX_EQ_GAIN1_LSB 0x0c4 +#define QSERDES_RX_RX_EQ_GAIN1_MSB 0x0c8 +#define QSERDES_RX_RX_EQ_GAIN2_LSB 0x0cc +#define QSERDES_RX_RX_EQ_GAIN2_MSB 0x0d0 +#define QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2 0x0d8 +#define QSERDES_RX_RX_EQU_ADAPTOR_CNTRL3 0x0dc +#define QSERDES_RX_RX_EQU_ADAPTOR_CNTRL4 0x0e0 +#define QSERDES_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1 0x108 +#define QSERDES_RX_RX_OFFSET_ADAPTOR_CNTRL2 0x10c +#define QSERDES_RX_SIGDET_ENABLES 0x110 +#define QSERDES_RX_SIGDET_CNTRL 0x114 +#define QSERDES_RX_SIGDET_LVL 0x118 +#define QSERDES_RX_SIGDET_DEGLITCH_CNTRL 0x11c +#define QSERDES_RX_RX_BAND 0x120 +#define QSERDES_RX_RX_INTERFACE_MODE 0x12c + +/* QMP PHY PCS registers */ +#define QPHY_POWER_DOWN_CONTROL 0x04 +#define QPHY_TXDEEMPH_M6DB_V0 0x24 +#define QPHY_TXDEEMPH_M3P5DB_V0 0x28 +#define QPHY_ENDPOINT_REFCLK_DRIVE 0x54 +#define QPHY_RX_IDLE_DTCT_CNTRL 0x58 +#define QPHY_POWER_STATE_CONFIG1 0x60 +#define QPHY_POWER_STATE_CONFIG2 0x64 +#define QPHY_POWER_STATE_CONFIG4 0x6c +#define QPHY_LOCK_DETECT_CONFIG1 0x80 +#define QPHY_LOCK_DETECT_CONFIG2 0x84 +#define QPHY_LOCK_DETECT_CONFIG3 0x88 +#define QPHY_PWRUP_RESET_DLY_TIME_AUXCLK 0xa0 +#define QPHY_LP_WAKEUP_DLY_TIME_AUXCLK 0xa4 + +/* QPHY_SW_RESET bit */ +#define SW_RESET BIT(0) +/* QPHY_POWER_DOWN_CONTROL */ +#define SW_PWRDN BIT(0) +#define REFCLK_DRV_DSBL BIT(1) +/* QPHY_START_CONTROL bits */ +#define SERDES_START BIT(0) +#define PCS_START BIT(1) +#define PLL_READY_GATE_EN BIT(3) +/* QPHY_PCS_STATUS bit */ +#define PHYSTATUS BIT(6) +/* QPHY_COM_PCS_READY_STATUS bit */ +#define PCS_READY BIT(0) + +#define PHY_INIT_COMPLETE_TIMEOUT 1000 +#define POWER_DOWN_DELAY_US_MIN 10 +#define POWER_DOWN_DELAY_US_MAX 11 + +#define MAX_PROP_NAME 32 + +struct qmp_phy_init_tbl { + unsigned int offset; + unsigned int val; + /* + * register part of layout ? + * if yes, then offset gives index in the reg-layout + */ + int in_layout; +}; +#define QMP_PHY_INIT_CFG(o, v) \ + { \ + .offset = o, \ + .val = v, \ + } +#define QMP_PHY_INIT_CFG_L(o, v) \ + { \ + .offset = o, \ + .val = v, \ + .in_layout = 1, \ + } + +/* set of registers with offsets different per-PHY */ +enum qphy_reg_layout { + /* Common block control registers */ + QPHY_COM_SW_RESET, + QPHY_COM_POWER_DOWN_CONTROL, + QPHY_COM_START_CONTROL, + QPHY_COM_PCS_READY_STATUS, + /* PCS registers */ + QPHY_PLL_LOCK_CHK_DLY_TIME, + QPHY_FLL_CNTRL1, + QPHY_FLL_CNTRL2, + QPHY_FLL_CNT_VAL_L, + QPHY_FLL_CNT_VAL_H_TOL, + QPHY_FLL_MAN_CODE, + QPHY_SW_RESET, + QPHY_START_CTRL, + QPHY_PCS_READY_STATUS, +}; + +static const unsigned int pciephy_regs_layout[] = { + [QPHY_COM_SW_RESET] = 0x400, + [QPHY_COM_POWER_DOWN_CONTROL] = 0x404, + [QPHY_COM_START_CONTROL] = 0x408, + [QPHY_COM_PCS_READY_STATUS] = 0x448, + [QPHY_PLL_LOCK_CHK_DLY_TIME] = 0xa8, + [QPHY_FLL_CNTRL1] = 0xc4, + [QPHY_FLL_CNTRL2] = 0xc8, + [QPHY_FLL_CNT_VAL_L] = 0xcc, + [QPHY_FLL_CNT_VAL_H_TOL] = 0xd0, + [QPHY_FLL_MAN_CODE] = 0xd4, + [QPHY_SW_RESET] = 0x00, + [QPHY_START_CTRL] = 0x08, + [QPHY_PCS_READY_STATUS] = 0x174, +}; + +static const unsigned int usb3phy_regs_layout[] = { + [QPHY_FLL_CNTRL1] = 0xc0, + [QPHY_FLL_CNTRL2] = 0xc4, + [QPHY_FLL_CNT_VAL_L] = 0xc8, + [QPHY_FLL_CNT_VAL_H_TOL] = 0xcc, + [QPHY_FLL_MAN_CODE] = 0xd0, + [QPHY_SW_RESET] = 0x00, + [QPHY_START_CTRL] = 0x08, + [QPHY_PCS_READY_STATUS] = 0x17c, +}; + +static const struct qmp_phy_init_tbl msm8996_pcie_serdes_tbl[] = { + QMP_PHY_INIT_CFG(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x1c), + QMP_PHY_INIT_CFG(QSERDES_COM_CLK_ENABLE1, 0x10), + QMP_PHY_INIT_CFG(QSERDES_COM_CLK_SELECT, 0x33), + QMP_PHY_INIT_CFG(QSERDES_COM_CMN_CONFIG, 0x06), + QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP_EN, 0x42), + QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_MAP, 0x00), + QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_TIMER1, 0xff), + QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_TIMER2, 0x1f), + QMP_PHY_INIT_CFG(QSERDES_COM_HSCLK_SEL, 0x01), + QMP_PHY_INIT_CFG(QSERDES_COM_SVS_MODE_CLK_SEL, 0x01), + QMP_PHY_INIT_CFG(QSERDES_COM_CORE_CLK_EN, 0x00), + QMP_PHY_INIT_CFG(QSERDES_COM_CORECLK_DIV, 0x0a), + QMP_PHY_INIT_CFG(QSERDES_COM_BG_TIMER, 0x09), + QMP_PHY_INIT_CFG(QSERDES_COM_DEC_START_MODE0, 0x82), + QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START3_MODE0, 0x03), + QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START2_MODE0, 0x55), + QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START1_MODE0, 0x55), + QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP3_MODE0, 0x00), + QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP2_MODE0, 0x1a), + QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP1_MODE0, 0x0a), + QMP_PHY_INIT_CFG(QSERDES_COM_CLK_SELECT, 0x33), + QMP_PHY_INIT_CFG(QSERDES_COM_SYS_CLK_CTRL, 0x02), + QMP_PHY_INIT_CFG(QSERDES_COM_SYSCLK_BUF_ENABLE, 0x1f), + QMP_PHY_INIT_CFG(QSERDES_COM_SYSCLK_EN_SEL, 0x04), + QMP_PHY_INIT_CFG(QSERDES_COM_CP_CTRL_MODE0, 0x0b), + QMP_PHY_INIT_CFG(QSERDES_COM_PLL_RCTRL_MODE0, 0x16), + QMP_PHY_INIT_CFG(QSERDES_COM_PLL_CCTRL_MODE0, 0x28), + QMP_PHY_INIT_CFG(QSERDES_COM_INTEGLOOP_GAIN1_MODE0, 0x00), + QMP_PHY_INIT_CFG(QSERDES_COM_INTEGLOOP_GAIN0_MODE0, 0x80), + QMP_PHY_INIT_CFG(QSERDES_COM_SSC_EN_CENTER, 0x01), + QMP_PHY_INIT_CFG(QSERDES_COM_SSC_PER1, 0x31), + QMP_PHY_INIT_CFG(QSERDES_COM_SSC_PER2, 0x01), + QMP_PHY_INIT_CFG(QSERDES_COM_SSC_ADJ_PER1, 0x02), + QMP_PHY_INIT_CFG(QSERDES_COM_SSC_ADJ_PER2, 0x00), + QMP_PHY_INIT_CFG(QSERDES_COM_SSC_STEP_SIZE1, 0x2f), + QMP_PHY_INIT_CFG(QSERDES_COM_SSC_STEP_SIZE2, 0x19), + QMP_PHY_INIT_CFG(QSERDES_COM_RESCODE_DIV_NUM, 0x15), + QMP_PHY_INIT_CFG(QSERDES_COM_BG_TRIM, 0x0f), + QMP_PHY_INIT_CFG(QSERDES_COM_PLL_IVCO, 0x0f), + QMP_PHY_INIT_CFG(QSERDES_COM_CLK_EP_DIV, 0x19), + QMP_PHY_INIT_CFG(QSERDES_COM_CLK_ENABLE1, 0x10), + QMP_PHY_INIT_CFG(QSERDES_COM_HSCLK_SEL, 0x00), + QMP_PHY_INIT_CFG(QSERDES_COM_RESCODE_DIV_NUM, 0x40), +}; + +static const struct qmp_phy_init_tbl msm8996_pcie_tx_tbl[] = { + QMP_PHY_INIT_CFG(QSERDES_TX_HIGHZ_TRANSCEIVEREN_BIAS_DRVR_EN, 0x45), + QMP_PHY_INIT_CFG(QSERDES_TX_LANE_MODE, 0x06), +}; + +static const struct qmp_phy_init_tbl msm8996_pcie_rx_tbl[] = { + QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_ENABLES, 0x1c), + QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2, 0x01), + QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL3, 0x00), + QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL4, 0xdb), + QMP_PHY_INIT_CFG(QSERDES_RX_RX_BAND, 0x18), + QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SO_GAIN, 0x04), + QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SO_GAIN_HALF, 0x04), + QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x4b), + QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_DEGLITCH_CNTRL, 0x14), + QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_LVL, 0x19), +}; + +static const struct qmp_phy_init_tbl msm8996_pcie_pcs_tbl[] = { + QMP_PHY_INIT_CFG(QPHY_RX_IDLE_DTCT_CNTRL, 0x4c), + QMP_PHY_INIT_CFG(QPHY_PWRUP_RESET_DLY_TIME_AUXCLK, 0x00), + QMP_PHY_INIT_CFG(QPHY_LP_WAKEUP_DLY_TIME_AUXCLK, 0x01), + + QMP_PHY_INIT_CFG_L(QPHY_PLL_LOCK_CHK_DLY_TIME, 0x05), + + QMP_PHY_INIT_CFG(QPHY_ENDPOINT_REFCLK_DRIVE, 0x05), + QMP_PHY_INIT_CFG(QPHY_POWER_DOWN_CONTROL, 0x02), + QMP_PHY_INIT_CFG(QPHY_POWER_STATE_CONFIG4, 0x00), + QMP_PHY_INIT_CFG(QPHY_POWER_STATE_CONFIG1, 0xa3), + QMP_PHY_INIT_CFG(QPHY_TXDEEMPH_M3P5DB_V0, 0x0e), +}; + +static const struct qmp_phy_init_tbl msm8996_usb3_serdes_tbl[] = { + QMP_PHY_INIT_CFG(QSERDES_COM_SYSCLK_EN_SEL, 0x14), + QMP_PHY_INIT_CFG(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x08), + QMP_PHY_INIT_CFG(QSERDES_COM_CLK_SELECT, 0x30), + QMP_PHY_INIT_CFG(QSERDES_COM_CMN_CONFIG, 0x06), + QMP_PHY_INIT_CFG(QSERDES_COM_SVS_MODE_CLK_SEL, 0x01), + QMP_PHY_INIT_CFG(QSERDES_COM_HSCLK_SEL, 0x00), + QMP_PHY_INIT_CFG(QSERDES_COM_BG_TRIM, 0x0f), + QMP_PHY_INIT_CFG(QSERDES_COM_PLL_IVCO, 0x0f), + QMP_PHY_INIT_CFG(QSERDES_COM_SYS_CLK_CTRL, 0x04), + /* PLL and Loop filter settings */ + QMP_PHY_INIT_CFG(QSERDES_COM_DEC_START_MODE0, 0x82), + QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START1_MODE0, 0x55), + QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START2_MODE0, 0x55), + QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START3_MODE0, 0x03), + QMP_PHY_INIT_CFG(QSERDES_COM_CP_CTRL_MODE0, 0x0b), + QMP_PHY_INIT_CFG(QSERDES_COM_PLL_RCTRL_MODE0, 0x16), + QMP_PHY_INIT_CFG(QSERDES_COM_PLL_CCTRL_MODE0, 0x28), + QMP_PHY_INIT_CFG(QSERDES_COM_INTEGLOOP_GAIN0_MODE0, 0x80), + QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_CTRL, 0x00), + QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP1_MODE0, 0x15), + QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP2_MODE0, 0x34), + QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP3_MODE0, 0x00), + QMP_PHY_INIT_CFG(QSERDES_COM_CORE_CLK_EN, 0x00), + QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP_CFG, 0x00), + QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_MAP, 0x00), + QMP_PHY_INIT_CFG(QSERDES_COM_BG_TIMER, 0x0a), + /* SSC settings */ + QMP_PHY_INIT_CFG(QSERDES_COM_SSC_EN_CENTER, 0x01), + QMP_PHY_INIT_CFG(QSERDES_COM_SSC_PER1, 0x31), + QMP_PHY_INIT_CFG(QSERDES_COM_SSC_PER2, 0x01), + QMP_PHY_INIT_CFG(QSERDES_COM_SSC_ADJ_PER1, 0x00), + QMP_PHY_INIT_CFG(QSERDES_COM_SSC_ADJ_PER2, 0x00), + QMP_PHY_INIT_CFG(QSERDES_COM_SSC_STEP_SIZE1, 0xde), + QMP_PHY_INIT_CFG(QSERDES_COM_SSC_STEP_SIZE2, 0x07), +}; + +static const struct qmp_phy_init_tbl msm8996_usb3_tx_tbl[] = { + QMP_PHY_INIT_CFG(QSERDES_TX_HIGHZ_TRANSCEIVEREN_BIAS_DRVR_EN, 0x45), + QMP_PHY_INIT_CFG(QSERDES_TX_RCV_DETECT_LVL_2, 0x12), + QMP_PHY_INIT_CFG(QSERDES_TX_LANE_MODE, 0x06), +}; + +static const struct qmp_phy_init_tbl msm8996_usb3_rx_tbl[] = { + QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_FASTLOCK_FO_GAIN, 0x0b), + QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SO_GAIN, 0x04), + QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2, 0x02), + QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL3, 0x4c), + QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL4, 0xbb), + QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x77), + QMP_PHY_INIT_CFG(QSERDES_RX_RX_OFFSET_ADAPTOR_CNTRL2, 0x80), + QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_CNTRL, 0x03), + QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_LVL, 0x18), + QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_DEGLITCH_CNTRL, 0x16), +}; + +static const struct qmp_phy_init_tbl msm8996_usb3_pcs_tbl[] = { + /* FLL settings */ + QMP_PHY_INIT_CFG_L(QPHY_FLL_CNTRL2, 0x03), + QMP_PHY_INIT_CFG_L(QPHY_FLL_CNTRL1, 0x02), + QMP_PHY_INIT_CFG_L(QPHY_FLL_CNT_VAL_L, 0x09), + QMP_PHY_INIT_CFG_L(QPHY_FLL_CNT_VAL_H_TOL, 0x42), + QMP_PHY_INIT_CFG_L(QPHY_FLL_MAN_CODE, 0x85), + + /* Lock Det settings */ + QMP_PHY_INIT_CFG(QPHY_LOCK_DETECT_CONFIG1, 0xd1), + QMP_PHY_INIT_CFG(QPHY_LOCK_DETECT_CONFIG2, 0x1f), + QMP_PHY_INIT_CFG(QPHY_LOCK_DETECT_CONFIG3, 0x47), + QMP_PHY_INIT_CFG(QPHY_POWER_STATE_CONFIG2, 0x08), +}; + +/* struct qmp_phy_cfg - per-PHY initialization config */ +struct qmp_phy_cfg { + /* phy-type - PCIE/UFS/USB */ + unsigned int type; + /* number of lanes provided by phy */ + int nlanes; + + /* Init sequence for PHY blocks - serdes, tx, rx, pcs */ + const struct qmp_phy_init_tbl *serdes_tbl; + int serdes_tbl_num; + const struct qmp_phy_init_tbl *tx_tbl; + int tx_tbl_num; + const struct qmp_phy_init_tbl *rx_tbl; + int rx_tbl_num; + const struct qmp_phy_init_tbl *pcs_tbl; + int pcs_tbl_num; + + /* clock ids to be requested */ + const char * const *clk_list; + int num_clks; + /* resets to be requested */ + const char * const *reset_list; + int num_resets; + /* regulators to be requested */ + const char * const *vreg_list; + int num_vregs; + + /* array of registers with different offsets */ + const unsigned int *regs; + + unsigned int start_ctrl; + unsigned int pwrdn_ctrl; + unsigned int mask_pcs_ready; + unsigned int mask_com_pcs_ready; + + /* true, if PHY has a separate PHY_COM control block */ + bool has_phy_com_ctrl; + /* true, if PHY has a reset for individual lanes */ + bool has_lane_rst; + /* true, if PHY needs delay after POWER_DOWN */ + bool has_pwrdn_delay; + /* power_down delay in usec */ + int pwrdn_delay_min; + int pwrdn_delay_max; +}; + +/** + * struct qmp_phy - per-lane phy descriptor + * + * @phy: generic phy + * @tx: iomapped memory space for lane's tx + * @rx: iomapped memory space for lane's rx + * @pcs: iomapped memory space for lane's pcs + * @pipe_clk: pipe lock + * @index: lane index + * @qmp: QMP phy to which this lane belongs + * @lane_rst: lane's reset controller + */ +struct qmp_phy { + struct phy *phy; + void __iomem *tx; + void __iomem *rx; + void __iomem *pcs; + struct clk *pipe_clk; + unsigned int index; + struct qcom_qmp *qmp; + struct reset_control *lane_rst; +}; + +/** + * struct qcom_qmp - structure holding QMP phy block attributes + * + * @dev: device + * @serdes: iomapped memory space for phy's serdes + * + * @clks: array of clocks required by phy + * @resets: array of resets required by phy + * @vregs: regulator supplies bulk data + * + * @cfg: phy specific configuration + * @phys: array of per-lane phy descriptors + * @phy_mutex: mutex lock for PHY common block initialization + * @init_count: phy common block initialization count + */ +struct qcom_qmp { + struct device *dev; + void __iomem *serdes; + + struct clk **clks; + struct reset_control **resets; + struct regulator_bulk_data *vregs; + + const struct qmp_phy_cfg *cfg; + struct qmp_phy **phys; + + struct mutex phy_mutex; + int init_count; +}; + +static inline void qphy_setbits(void __iomem *base, u32 offset, u32 val) +{ + u32 reg; + + reg = readl(base + offset); + reg |= val; + writel(reg, base + offset); + + /* ensure that above write is through */ + readl(base + offset); +} + +static inline void qphy_clrbits(void __iomem *base, u32 offset, u32 val) +{ + u32 reg; + + reg = readl(base + offset); + reg &= ~val; + writel(reg, base + offset); + + /* ensure that above write is through */ + readl(base + offset); +} + +/* list of clocks required by phy */ +static const char * const msm8996_phy_clk_l[] = { + "aux", "cfg_ahb", "ref", +}; + +/* list of resets */ +static const char * const msm8996_pciephy_reset_l[] = { + "phy", "common", "cfg", +}; + +static const char * const msm8996_usb3phy_reset_l[] = { + "phy", "common", +}; + +/* list of regulators */ +static const char * const msm8996_phy_vreg_l[] = { + "vdda-phy", "vdda-pll", +}; + +static const struct qmp_phy_cfg msm8996_pciephy_cfg = { + .type = PHY_TYPE_PCIE, + .nlanes = 3, + + .serdes_tbl = msm8996_pcie_serdes_tbl, + .serdes_tbl_num = ARRAY_SIZE(msm8996_pcie_serdes_tbl), + .tx_tbl = msm8996_pcie_tx_tbl, + .tx_tbl_num = ARRAY_SIZE(msm8996_pcie_tx_tbl), + .rx_tbl = msm8996_pcie_rx_tbl, + .rx_tbl_num = ARRAY_SIZE(msm8996_pcie_rx_tbl), + .pcs_tbl = msm8996_pcie_pcs_tbl, + .pcs_tbl_num = ARRAY_SIZE(msm8996_pcie_pcs_tbl), + .clk_list = msm8996_phy_clk_l, + .num_clks = ARRAY_SIZE(msm8996_phy_clk_l), + .reset_list = msm8996_pciephy_reset_l, + .num_resets = ARRAY_SIZE(msm8996_pciephy_reset_l), + .vreg_list = msm8996_phy_vreg_l, + .num_vregs = ARRAY_SIZE(msm8996_phy_vreg_l), + .regs = pciephy_regs_layout, + + .start_ctrl = PCS_START | PLL_READY_GATE_EN, + .pwrdn_ctrl = SW_PWRDN | REFCLK_DRV_DSBL, + .mask_com_pcs_ready = PCS_READY, + + .has_phy_com_ctrl = true, + .has_lane_rst = true, + .has_pwrdn_delay = true, + .pwrdn_delay_min = POWER_DOWN_DELAY_US_MIN, + .pwrdn_delay_max = POWER_DOWN_DELAY_US_MAX, +}; + +static const struct qmp_phy_cfg msm8996_usb3phy_cfg = { + .type = PHY_TYPE_USB3, + .nlanes = 1, + + .serdes_tbl = msm8996_usb3_serdes_tbl, + .serdes_tbl_num = ARRAY_SIZE(msm8996_usb3_serdes_tbl), + .tx_tbl = msm8996_usb3_tx_tbl, + .tx_tbl_num = ARRAY_SIZE(msm8996_usb3_tx_tbl), + .rx_tbl = msm8996_usb3_rx_tbl, + .rx_tbl_num = ARRAY_SIZE(msm8996_usb3_rx_tbl), + .pcs_tbl = msm8996_usb3_pcs_tbl, + .pcs_tbl_num = ARRAY_SIZE(msm8996_usb3_pcs_tbl), + .clk_list = msm8996_phy_clk_l, + .num_clks = ARRAY_SIZE(msm8996_phy_clk_l), + .reset_list = msm8996_usb3phy_reset_l, + .num_resets = ARRAY_SIZE(msm8996_usb3phy_reset_l), + .vreg_list = msm8996_phy_vreg_l, + .num_vregs = ARRAY_SIZE(msm8996_phy_vreg_l), + .regs = usb3phy_regs_layout, + + .start_ctrl = SERDES_START | PCS_START, + .pwrdn_ctrl = SW_PWRDN, + .mask_pcs_ready = PHYSTATUS, +}; + +static void qcom_qmp_phy_configure(void __iomem *base, + const unsigned int *regs, + const struct qmp_phy_init_tbl tbl[], + int num) +{ + int i; + const struct qmp_phy_init_tbl *t = tbl; + + if (!t) + return; + + for (i = 0; i < num; i++, t++) { + if (t->in_layout) + writel(t->val, base + regs[t->offset]); + else + writel(t->val, base + t->offset); + } +} + +static int qcom_qmp_phy_poweron(struct phy *phy) +{ + struct qmp_phy *qphy = phy_get_drvdata(phy); + struct qcom_qmp *qmp = qphy->qmp; + int num = qmp->cfg->num_vregs; + int ret; + + dev_vdbg(&phy->dev, "Powering on QMP phy\n"); + + /* turn on regulator supplies */ + ret = regulator_bulk_enable(num, qmp->vregs); + if (ret) { + dev_err(qmp->dev, "failed to enable regulators, err=%d\n", ret); + return ret; + } + + ret = clk_prepare_enable(qphy->pipe_clk); + if (ret) { + dev_err(qmp->dev, "pipe_clk enable failed, err=%d\n", ret); + regulator_bulk_disable(num, qmp->vregs); + return ret; + } + + return 0; +} + +static int qcom_qmp_phy_poweroff(struct phy *phy) +{ + struct qmp_phy *qphy = phy_get_drvdata(phy); + struct qcom_qmp *qmp = qphy->qmp; + + clk_disable_unprepare(qphy->pipe_clk); + + regulator_bulk_disable(qmp->cfg->num_vregs, qmp->vregs); + + return 0; +} + +static int qcom_qmp_phy_com_init(struct qcom_qmp *qmp) +{ + const struct qmp_phy_cfg *cfg = qmp->cfg; + void __iomem *serdes = qmp->serdes; + int ret, i; + + mutex_lock(&qmp->phy_mutex); + if (qmp->init_count++) { + mutex_unlock(&qmp->phy_mutex); + return 0; + } + + for (i = 0; i < cfg->num_resets; i++) { + ret = reset_control_deassert(qmp->resets[i]); + if (ret) { + dev_err(qmp->dev, "%s reset deassert failed\n", + qmp->cfg->reset_list[i]); + while (--i >= 0) + reset_control_assert(qmp->resets[i]); + goto err_rst; + } + } + + if (cfg->has_phy_com_ctrl) + qphy_setbits(serdes, cfg->regs[QPHY_COM_POWER_DOWN_CONTROL], + SW_PWRDN); + + /* Serdes configuration */ + qcom_qmp_phy_configure(serdes, cfg->regs, cfg->serdes_tbl, + cfg->serdes_tbl_num); + + if (cfg->has_phy_com_ctrl) { + void __iomem *status; + unsigned int mask, val; + + qphy_clrbits(serdes, cfg->regs[QPHY_COM_SW_RESET], + SW_RESET); + qphy_setbits(serdes, cfg->regs[QPHY_COM_START_CONTROL], + SERDES_START | PCS_START); + + status = serdes + cfg->regs[QPHY_COM_PCS_READY_STATUS]; + mask = cfg->mask_com_pcs_ready; + + ret = readl_poll_timeout(status, val, (val & mask), 10, + PHY_INIT_COMPLETE_TIMEOUT); + if (ret) { + dev_err(qmp->dev, + "phy common block init timed-out\n"); + goto err_com_init; + } + } + + mutex_unlock(&qmp->phy_mutex); + + return 0; + +err_com_init: + while (--i >= 0) + reset_control_assert(qmp->resets[i]); +err_rst: + mutex_unlock(&qmp->phy_mutex); + return ret; +} + +static int qcom_qmp_phy_com_exit(struct qcom_qmp *qmp) +{ + const struct qmp_phy_cfg *cfg = qmp->cfg; + void __iomem *serdes = qmp->serdes; + int i = cfg->num_resets; + + mutex_lock(&qmp->phy_mutex); + if (--qmp->init_count) { + mutex_unlock(&qmp->phy_mutex); + return 0; + } + + if (cfg->has_phy_com_ctrl) { + qphy_setbits(serdes, cfg->regs[QPHY_COM_START_CONTROL], + SERDES_START | PCS_START); + qphy_clrbits(serdes, cfg->regs[QPHY_COM_SW_RESET], + SW_RESET); + qphy_setbits(serdes, cfg->regs[QPHY_COM_POWER_DOWN_CONTROL], + SW_PWRDN); + } + + while (--i >= 0) + reset_control_assert(qmp->resets[i]); + + mutex_unlock(&qmp->phy_mutex); + + return 0; +} + +/* PHY Initialization */ +static int qcom_qmp_phy_init(struct phy *phy) +{ + struct qmp_phy *qphy = phy_get_drvdata(phy); + struct qcom_qmp *qmp = qphy->qmp; + const struct qmp_phy_cfg *cfg = qmp->cfg; + void __iomem *tx = qphy->tx; + void __iomem *rx = qphy->rx; + void __iomem *pcs = qphy->pcs; + void __iomem *status; + unsigned int mask, val; + int ret, i; + + dev_vdbg(qmp->dev, "Initializing QMP phy\n"); + + for (i = 0; i < qmp->cfg->num_clks; i++) { + ret = clk_prepare_enable(qmp->clks[i]); + if (ret) { + dev_err(qmp->dev, "failed to enable %s clk, err=%d\n", + qmp->cfg->clk_list[i], ret); + while (--i >= 0) + clk_disable_unprepare(qmp->clks[i]); + } + } + + ret = qcom_qmp_phy_com_init(qmp); + if (ret) + goto err_com_init; + + if (cfg->has_lane_rst) { + ret = reset_control_deassert(qphy->lane_rst); + if (ret) { + dev_err(qmp->dev, "lane%d reset deassert failed\n", + qphy->index); + goto err_lane_rst; + } + } + + /* Tx, Rx, and PCS configurations */ + qcom_qmp_phy_configure(tx, cfg->regs, cfg->tx_tbl, cfg->tx_tbl_num); + qcom_qmp_phy_configure(rx, cfg->regs, cfg->rx_tbl, cfg->rx_tbl_num); + qcom_qmp_phy_configure(pcs, cfg->regs, cfg->pcs_tbl, cfg->pcs_tbl_num); + + /* + * Pull out PHY from POWER DOWN state. + * This is active low enable signal to power-down PHY. + */ + qphy_setbits(pcs, QPHY_POWER_DOWN_CONTROL, cfg->pwrdn_ctrl); + + if (cfg->has_pwrdn_delay) + usleep_range(cfg->pwrdn_delay_min, cfg->pwrdn_delay_max); + + /* start SerDes and Phy-Coding-Sublayer */ + qphy_setbits(pcs, cfg->regs[QPHY_START_CTRL], cfg->start_ctrl); + + /* Pull PHY out of reset state */ + qphy_clrbits(pcs, cfg->regs[QPHY_SW_RESET], SW_RESET); + + status = pcs + cfg->regs[QPHY_PCS_READY_STATUS]; + mask = cfg->mask_pcs_ready; + + ret = readl_poll_timeout(status, val, !(val & mask), 1, + PHY_INIT_COMPLETE_TIMEOUT); + if (ret) { + dev_err(qmp->dev, "phy initialization timed-out\n"); + goto err_pcs_ready; + } + + return ret; + +err_pcs_ready: + if (cfg->has_lane_rst) + reset_control_assert(qphy->lane_rst); +err_lane_rst: + qcom_qmp_phy_com_exit(qmp); +err_com_init: + while (--i >= 0) + clk_disable_unprepare(qmp->clks[i]); + + return ret; +} + +static int qcom_qmp_phy_exit(struct phy *phy) +{ + struct qmp_phy *qphy = phy_get_drvdata(phy); + struct qcom_qmp *qmp = qphy->qmp; + const struct qmp_phy_cfg *cfg = qmp->cfg; + int i = cfg->num_clks; + + /* PHY reset */ + qphy_setbits(qphy->pcs, cfg->regs[QPHY_SW_RESET], SW_RESET); + + /* stop SerDes and Phy-Coding-Sublayer */ + qphy_clrbits(qphy->pcs, cfg->regs[QPHY_START_CTRL], cfg->start_ctrl); + + /* Put PHY into POWER DOWN state: active low */ + qphy_clrbits(qphy->pcs, QPHY_POWER_DOWN_CONTROL, + cfg->pwrdn_ctrl); + + if (cfg->has_lane_rst) + reset_control_assert(qphy->lane_rst); + + qcom_qmp_phy_com_exit(qmp); + + while (--i >= 0) + clk_disable_unprepare(qmp->clks[i]); + + return 0; +} + +static int qcom_qmp_phy_vreg_init(struct device *dev) +{ + struct qcom_qmp *qmp = dev_get_drvdata(dev); + int num = qmp->cfg->num_vregs; + int i; + + qmp->vregs = devm_kcalloc(dev, num, sizeof(qmp->vregs), GFP_KERNEL); + if (!qmp->vregs) + return -ENOMEM; + + for (i = 0; i < num; i++) + qmp->vregs[i].supply = qmp->cfg->vreg_list[i]; + + return devm_regulator_bulk_get(dev, num, qmp->vregs); +} + +static int qcom_qmp_phy_reset_init(struct device *dev) +{ + struct qcom_qmp *qmp = dev_get_drvdata(dev); + int i; + + qmp->resets = devm_kcalloc(dev, qmp->cfg->num_resets, + sizeof(*qmp->resets), GFP_KERNEL); + if (!qmp->resets) + return -ENOMEM; + + for (i = 0; i < qmp->cfg->num_resets; i++) { + struct reset_control *rst; + const char *name = qmp->cfg->reset_list[i]; + + rst = devm_reset_control_get(dev, name); + if (IS_ERR(rst)) { + dev_err(dev, "failed to get %s reset\n", name); + return PTR_ERR(rst); + } + qmp->resets[i] = rst; + } + + return 0; +} + +static int qcom_qmp_phy_clk_init(struct device *dev) +{ + struct qcom_qmp *qmp = dev_get_drvdata(dev); + int ret, i; + + qmp->clks = devm_kcalloc(dev, qmp->cfg->num_clks, + sizeof(*qmp->clks), GFP_KERNEL); + if (!qmp->clks) + return -ENOMEM; + + for (i = 0; i < qmp->cfg->num_clks; i++) { + struct clk *_clk; + const char *name = qmp->cfg->clk_list[i]; + + _clk = devm_clk_get(dev, name); + if (IS_ERR(_clk)) { + ret = PTR_ERR(_clk); + if (ret != -EPROBE_DEFER) + dev_err(dev, "failed to get %s clk, %d\n", + name, ret); + return ret; + } + qmp->clks[i] = _clk; + } + + return 0; +} + +/* + * Register a fixed rate pipe clock. + * + * The _pipe_clksrc generated by PHY goes to the GCC that gate + * controls it. The _pipe_clk coming out of the GCC is requested + * by the PHY driver for its operations. + * We register the _pipe_clksrc here. The gcc driver takes care + * of assigning this _pipe_clksrc as parent to _pipe_clk. + * Below picture shows this relationship. + * + * +---------------+ + * | PHY block |<<---------------------------------------+ + * | | | + * | +-------+ | +-----+ | + * I/P---^-->| PLL |---^--->pipe_clksrc--->| GCC |--->pipe_clk---+ + * clk | +-------+ | +-----+ + * +---------------+ + */ +static int phy_pipe_clk_register(struct qcom_qmp *qmp, int id) +{ + char name[24]; + struct clk_fixed_rate *fixed; + struct clk_init_data init = { }; + + switch (qmp->cfg->type) { + case PHY_TYPE_USB3: + snprintf(name, sizeof(name), "usb3_phy_pipe_clk_src"); + break; + case PHY_TYPE_PCIE: + snprintf(name, sizeof(name), "pcie_%d_pipe_clk_src", id); + break; + default: + /* not all phys register pipe clocks, so return success */ + return 0; + } + + fixed = devm_kzalloc(qmp->dev, sizeof(*fixed), GFP_KERNEL); + if (!fixed) + return -ENOMEM; + + init.name = name; + init.ops = &clk_fixed_rate_ops; + + /* controllers using QMP phys use 125MHz pipe clock interface */ + fixed->fixed_rate = 125000000; + fixed->hw.init = &init; + + return devm_clk_hw_register(qmp->dev, &fixed->hw); +} + +static const struct phy_ops qcom_qmp_phy_gen_ops = { + .init = qcom_qmp_phy_init, + .exit = qcom_qmp_phy_exit, + .power_on = qcom_qmp_phy_poweron, + .power_off = qcom_qmp_phy_poweroff, + .owner = THIS_MODULE, +}; + +static +int qcom_qmp_phy_create(struct device *dev, struct device_node *np, int id) +{ + struct qcom_qmp *qmp = dev_get_drvdata(dev); + struct phy *generic_phy; + struct qmp_phy *qphy; + char prop_name[MAX_PROP_NAME]; + int ret; + + qphy = devm_kzalloc(dev, sizeof(*qphy), GFP_KERNEL); + if (!qphy) + return -ENOMEM; + + /* + * Get memory resources for each phy lane: + * Resources are indexed as: tx -> 0; rx -> 1; pcs -> 2. + */ + qphy->tx = of_iomap(np, 0); + if (IS_ERR(qphy->tx)) + return PTR_ERR(qphy->tx); + + qphy->rx = of_iomap(np, 1); + if (IS_ERR(qphy->rx)) + return PTR_ERR(qphy->rx); + + qphy->pcs = of_iomap(np, 2); + if (IS_ERR(qphy->pcs)) + return PTR_ERR(qphy->pcs); + + /* + * Get PHY's Pipe clock, if any. USB3 and PCIe are PIPE3 + * based phys, so they essentially have pipe clock. So, + * we return error in case phy is USB3 or PIPE type. + * Otherwise, we initialize pipe clock to NULL for + * all phys that don't need this. + */ + snprintf(prop_name, sizeof(prop_name), "pipe%d", id); + qphy->pipe_clk = of_clk_get_by_name(np, prop_name); + if (IS_ERR(qphy->pipe_clk)) { + if (qmp->cfg->type == PHY_TYPE_PCIE || + qmp->cfg->type == PHY_TYPE_USB3) { + ret = PTR_ERR(qphy->pipe_clk); + if (ret != -EPROBE_DEFER) + dev_err(dev, + "failed to get lane%d pipe_clk, %d\n", + id, ret); + return ret; + } + qphy->pipe_clk = NULL; + } + + /* Get lane reset, if any */ + if (qmp->cfg->has_lane_rst) { + snprintf(prop_name, sizeof(prop_name), "lane%d", id); + qphy->lane_rst = of_reset_control_get(np, prop_name); + if (IS_ERR(qphy->lane_rst)) { + dev_err(dev, "failed to get lane%d reset\n", id); + return PTR_ERR(qphy->lane_rst); + } + } + + generic_phy = devm_phy_create(dev, np, &qcom_qmp_phy_gen_ops); + if (IS_ERR(generic_phy)) { + ret = PTR_ERR(generic_phy); + dev_err(dev, "failed to create qphy %d\n", ret); + return ret; + } + + qphy->phy = generic_phy; + qphy->index = id; + qphy->qmp = qmp; + qmp->phys[id] = qphy; + phy_set_drvdata(generic_phy, qphy); + + return 0; +} + +static const struct of_device_id qcom_qmp_phy_of_match_table[] = { + { + .compatible = "qcom,msm8996-qmp-pcie-phy", + .data = &msm8996_pciephy_cfg, + }, { + .compatible = "qcom,msm8996-qmp-usb3-phy", + .data = &msm8996_usb3phy_cfg, + }, + { }, +}; +MODULE_DEVICE_TABLE(of, qcom_qmp_phy_of_match_table); + +static int qcom_qmp_phy_probe(struct platform_device *pdev) +{ + struct qcom_qmp *qmp; + struct device *dev = &pdev->dev; + struct resource *res; + struct device_node *child; + struct phy_provider *phy_provider; + void __iomem *base; + int num, id; + int ret; + + qmp = devm_kzalloc(dev, sizeof(*qmp), GFP_KERNEL); + if (!qmp) + return -ENOMEM; + + qmp->dev = dev; + dev_set_drvdata(dev, qmp); + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + base = devm_ioremap_resource(dev, res); + if (IS_ERR(base)) + return PTR_ERR(base); + + /* per PHY serdes; usually located at base address */ + qmp->serdes = base; + + mutex_init(&qmp->phy_mutex); + + /* Get the specific init parameters of QMP phy */ + qmp->cfg = of_device_get_match_data(dev); + + ret = qcom_qmp_phy_clk_init(dev); + if (ret) + return ret; + + ret = qcom_qmp_phy_reset_init(dev); + if (ret) + return ret; + + ret = qcom_qmp_phy_vreg_init(dev); + if (ret) { + dev_err(dev, "failed to get regulator supplies\n"); + return ret; + } + + num = of_get_available_child_count(dev->of_node); + /* do we have a rogue child node ? */ + if (num > qmp->cfg->nlanes) + return -EINVAL; + + qmp->phys = devm_kcalloc(dev, num, sizeof(*qmp->phys), GFP_KERNEL); + if (!qmp->phys) + return -ENOMEM; + + id = 0; + for_each_available_child_of_node(dev->of_node, child) { + /* Create per-lane phy */ + ret = qcom_qmp_phy_create(dev, child, id); + if (ret) { + dev_err(dev, "failed to create lane%d phy, %d\n", + id, ret); + return ret; + } + + /* + * Register the pipe clock provided by phy. + * See function description to see details of this pipe clock. + */ + ret = phy_pipe_clk_register(qmp, id); + if (ret) { + dev_err(qmp->dev, + "failed to register pipe clock source\n"); + return ret; + } + id++; + } + + phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate); + if (!IS_ERR(phy_provider)) + dev_info(dev, "Registered Qcom-QMP phy\n"); + + return PTR_ERR_OR_ZERO(phy_provider); +} + +static struct platform_driver qcom_qmp_phy_driver = { + .probe = qcom_qmp_phy_probe, + .driver = { + .name = "qcom-qmp-phy", + .of_match_table = qcom_qmp_phy_of_match_table, + }, +}; + +module_platform_driver(qcom_qmp_phy_driver); + +MODULE_AUTHOR("Vivek Gautam "); +MODULE_DESCRIPTION("Qualcomm QMP PHY driver"); +MODULE_LICENSE("GPL v2"); -- The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project