From: Yoshihiro Kaneko <ykaneko0929@gmail.com>
To: linux-renesas-soc@vger.kernel.org
Cc: Magnus Damm <magnus.damm@gmail.com>,
Simon Horman <horms@verge.net.au>,
Geert Uytterhoeven <geert@linux-m68k.org>,
linux-arm-kernel@lists.infradead.org
Subject: [PATCH/RFT] arm: dts: renesas: r7s9210-rza2mevb: sort nodes of rza2mevb board
Date: Fri, 17 May 2019 23:43:07 +0900 [thread overview]
Message-ID: <1558104187-2842-1-git-send-email-ykaneko0929@gmail.com> (raw)
This patch sorts the nodes of arch/arm/boot/dts/r7s9210-rza2mevb.dts.
* Sort subnodes of root ("/") node alphabetically
* Sort following top-level nodes alphabetically
* Sort subnodes of pinctrl alphabetically
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
---
This patch is based on the devel branch of Simon Horman's renesas tree.
arch/arm/boot/dts/r7s9210-rza2mevb.dts | 92 +++++++++++++++++-----------------
1 file changed, 46 insertions(+), 46 deletions(-)
diff --git a/arch/arm/boot/dts/r7s9210-rza2mevb.dts b/arch/arm/boot/dts/r7s9210-rza2mevb.dts
index fa44e35..71808ce 100644
--- a/arch/arm/boot/dts/r7s9210-rza2mevb.dts
+++ b/arch/arm/boot/dts/r7s9210-rza2mevb.dts
@@ -26,11 +26,6 @@
stdout-path = "serial0:115200n8";
};
- memory@40000000 {
- device_type = "memory";
- reg = <0x40000000 0x00800000>; /* HyperRAM */
- };
-
lbsc {
#address-cells = <1>;
#size-cells = <1>;
@@ -46,6 +41,33 @@
gpios = <&pinctrl RZA2_PIN(PORTC, 1) GPIO_ACTIVE_HIGH>;
};
};
+
+ memory@40000000 {
+ device_type = "memory";
+ reg = <0x40000000 0x00800000>; /* HyperRAM */
+ };
+};
+
+ðer0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <ð0_pins>;
+ status = "okay";
+ renesas,no-ether-link;
+ phy-handle = <&phy0>;
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+};
+
+ðer1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <ð1_pins>;
+ status = "okay";
+ renesas,no-ether-link;
+ phy-handle = <&phy1>;
+ phy1: ethernet-phy@1 {
+ reg = <0>;
+ };
};
/* EXTAL */
@@ -53,23 +75,16 @@
clock-frequency = <24000000>; /* 24MHz */
};
-/* RTC_X1 */
-&rtc_x1_clk {
- clock-frequency = <32768>;
+/* High resolution System tick timers */
+&ostm0 {
+ status = "okay";
};
-/* USB_X1 */
-&usb_x1_clk {
- clock-frequency = <48000000>;
+&ostm1 {
+ status = "okay";
};
&pinctrl {
- /* Serial Console */
- scif4_pins: serial4 {
- pinmux = <RZA2_PINMUX(PORT9, 0, 4)>, /* TxD4 */
- <RZA2_PINMUX(PORT9, 1, 4)>; /* RxD4 */
- };
-
eth0_pins: eth0 {
pinmux = <RZA2_PINMUX(PORTE, 0, 7)>, /* REF50CK0 */
<RZA2_PINMUX(PORT6, 1, 7)>, /* RMMI0_TXDEN */
@@ -98,6 +113,12 @@
<RZA2_PINMUX(PORTL, 1, 5)>; /* IRQ5 */
};
+ /* Serial Console */
+ scif4_pins: serial4 {
+ pinmux = <RZA2_PINMUX(PORT9, 0, 4)>, /* TxD4 */
+ <RZA2_PINMUX(PORT9, 1, 4)>; /* RxD4 */
+ };
+
sdhi0_pins: sdhi0 {
pinmux = <RZA2_PINMUX(PORT5, 0, 3)>, /* SD0_CD */
<RZA2_PINMUX(PORT5, 1, 3)>; /* SD0_WP */
@@ -109,13 +130,9 @@
};
};
-/* High resolution System tick timers */
-&ostm0 {
- status = "okay";
-};
-
-&ostm1 {
- status = "okay";
+/* RTC_X1 */
+&rtc_x1_clk {
+ clock-frequency = <32768>;
};
/* Serial Console */
@@ -126,28 +143,6 @@
status = "okay";
};
-ðer0 {
- pinctrl-names = "default";
- pinctrl-0 = <ð0_pins>;
- status = "okay";
- renesas,no-ether-link;
- phy-handle = <&phy0>;
- phy0: ethernet-phy@0 {
- reg = <0>;
- };
-};
-
-ðer1 {
- pinctrl-names = "default";
- pinctrl-0 = <ð1_pins>;
- status = "okay";
- renesas,no-ether-link;
- phy-handle = <&phy1>;
- phy1: ethernet-phy@1 {
- reg = <0>;
- };
-};
-
&sdhi0 {
pinctrl-names = "default";
pinctrl-0 = <&sdhi0_pins>;
@@ -161,3 +156,8 @@
bus-width = <4>;
status = "okay";
};
+
+/* USB_X1 */
+&usb_x1_clk {
+ clock-frequency = <48000000>;
+};
--
1.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next reply other threads:[~2019-05-17 14:43 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-05-17 14:43 Yoshihiro Kaneko [this message]
2019-05-28 8:08 ` [PATCH/RFT] arm: dts: renesas: r7s9210-rza2mevb: sort nodes of rza2mevb board Geert Uytterhoeven
2019-05-29 10:22 ` Simon Horman
2019-05-29 10:32 ` Simon Horman
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1558104187-2842-1-git-send-email-ykaneko0929@gmail.com \
--to=ykaneko0929@gmail.com \
--cc=geert@linux-m68k.org \
--cc=horms@verge.net.au \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-renesas-soc@vger.kernel.org \
--cc=magnus.damm@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).