From: Olivier Moysan <olivier.moysan@st.com>
To: <linux-stm32@st-md-mailman.stormreply.com>,
<alexandre.torgue@st.com>, <robh@kernel.org>,
<mark.rutland@arm.com>, <devicetree@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>, <olivier.moysan@st.com>
Subject: [PATCH] ARM: dts: stm32: add audio codec support on stm32mp157a-dk1 board
Date: Fri, 5 Jul 2019 13:53:00 +0200 [thread overview]
Message-ID: <1562327580-19647-1-git-send-email-olivier.moysan@st.com> (raw)
Add support of Cirrus cs42l51 audio codec on stm32mp157a-dk1 board.
Configuration overview:
- SAI2A is the CPU interface used for the codec audio playback
- SAI2B is the CPU interface used for the codec audio record
- SAI2A is configured as a clock provider for the audio codec
- SAI2A&B are configured as slave of the audio codec
- SAI2A&B share the same interface of the audio codec
Note:
In master mode, cs42l51 audio codec provides a bitclock
at 64 x FS, regardless of data width. This means that
slot width is always 32 bits.
Set slot width to 32 bits and slot number to 2
in SAI2A&B endpoint nodes, to match this constraint.
dai-tdm-slot-num and dai-tdm-slot-width properties are used here,
assuming that i2s is a special case of tdm, where slot number is 2.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
---
arch/arm/boot/dts/stm32mp157a-dk1.dts | 89 +++++++++++++++++++++++++++++++++++
1 file changed, 89 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp157a-dk1.dts b/arch/arm/boot/dts/stm32mp157a-dk1.dts
index f3f0e37aad4d..0f5b3c77153d 100644
--- a/arch/arm/boot/dts/stm32mp157a-dk1.dts
+++ b/arch/arm/boot/dts/stm32mp157a-dk1.dts
@@ -48,6 +48,17 @@
default-state = "off";
};
};
+
+ sound {
+ compatible = "audio-graph-card";
+ label = "STM32MP1-DK";
+ routing =
+ "Playback" , "MCLK",
+ "Capture" , "MCLK",
+ "MICL" , "Mic Bias";
+ dais = <&sai2a_port &sai2b_port>;
+ status = "okay";
+ };
};
&cec {
@@ -116,6 +127,39 @@
};
};
};
+
+ cs42l51: cs42l51@4a {
+ compatible = "cirrus,cs42l51";
+ reg = <0x4a>;
+ #sound-dai-cells = <0>;
+ VL-supply = <&v3v3>;
+ VD-supply = <&v1v8_audio>;
+ VA-supply = <&v1v8_audio>;
+ VAHP-supply = <&v1v8_audio>;
+ reset-gpios = <&gpiog 9 GPIO_ACTIVE_LOW>;
+ clocks = <&sai2a>;
+ clock-names = "MCLK";
+ status = "okay";
+
+ cs42l51_port: port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cs42l51_tx_endpoint: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&sai2a_endpoint>;
+ frame-master;
+ bitclock-master;
+ };
+
+ cs42l51_rx_endpoint: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&sai2b_endpoint>;
+ frame-master;
+ bitclock-master;
+ };
+ };
+ };
};
&i2c4 {
@@ -297,6 +341,51 @@
status = "okay";
};
+&sai2 {
+ clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
+ clock-names = "pclk", "x8k", "x11k";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sai2a_pins_a>, <&sai2b_pins_b>;
+ pinctrl-1 = <&sai2a_sleep_pins_a>, <&sai2b_sleep_pins_b>;
+ status = "okay";
+
+ sai2a: audio-controller@4400b004 {
+ #clock-cells = <0>;
+ dma-names = "tx";
+ clocks = <&rcc SAI2_K>;
+ clock-names = "sai_ck";
+ status = "okay";
+
+ sai2a_port: port {
+ sai2a_endpoint: endpoint {
+ remote-endpoint = <&cs42l51_tx_endpoint>;
+ format = "i2s";
+ mclk-fs = <256>;
+ dai-tdm-slot-num = <2>;
+ dai-tdm-slot-width = <32>;
+ };
+ };
+ };
+
+ sai2b: audio-controller@4400b024 {
+ dma-names = "rx";
+ st,sync = <&sai2a 2>;
+ clocks = <&rcc SAI2_K>, <&sai2a>;
+ clock-names = "sai_ck", "MCLK";
+ status = "okay";
+
+ sai2b_port: port {
+ sai2b_endpoint: endpoint {
+ remote-endpoint = <&cs42l51_rx_endpoint>;
+ format = "i2s";
+ mclk-fs = <256>;
+ dai-tdm-slot-num = <2>;
+ dai-tdm-slot-width = <32>;
+ };
+ };
+ };
+};
+
&sdmmc1 {
pinctrl-names = "default", "opendrain", "sleep";
pinctrl-0 = <&sdmmc1_b4_pins_a>;
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next reply other threads:[~2019-07-05 14:03 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-07-05 11:53 Olivier Moysan [this message]
2019-07-24 16:40 ` [PATCH] ARM: dts: stm32: add audio codec support on stm32mp157a-dk1 board Alexandre Torgue
2019-07-25 9:41 ` Olivier MOYSAN
2019-07-29 7:23 ` Alexandre Torgue
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1562327580-19647-1-git-send-email-olivier.moysan@st.com \
--to=olivier.moysan@st.com \
--cc=alexandre.torgue@st.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-stm32@st-md-mailman.stormreply.com \
--cc=mark.rutland@arm.com \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).