Linux-ARM-Kernel Archive on lore.kernel.org
 help / color / Atom feed
From: Stefan Wahren <wahrenst@gmx.net>
To: Eric Anholt <eric@anholt.net>,
	Florian Fainelli <f.fainelli@gmail.com>,
	Ray Jui <rjui@broadcom.com>,
	Scott Branden <sbranden@broadcom.com>,
	Nicolas Saenz Julienne <nsaenzjulienne@suse.de>,
	Rob Herring <robh+dt@kernel.org>,
	Mark Rutland <mark.rutland@arm.com>,
	Linus Walleij <linus.walleij@linaro.org>,
	Michael Turquette <mturquette@baylibre.com>,
	Stephen Boyd <sboyd@kernel.org>,
	Ulf Hansson <ulf.hansson@linaro.org>,
	Adrian Hunter <adrian.hunter@intel.com>,
	Mark Brown <broonie@kernel.org>
Cc: Al Cooper <alcooperx@gmail.com>,
	bcm-kernel-feedback-list@broadcom.com,
	linux-rpi-kernel@lists.infradead.org,
	linux-arm-kernel@lists.infradead.org
Subject: [PATCH RFC 10/18] pinctrl: bcm2835: bcm7211: Add support for 7211 pull-up functionality
Date: Wed, 17 Jul 2019 21:50:18 +0200
Message-ID: <1563393026-17118-11-git-send-email-wahrenst@gmx.net> (raw)
In-Reply-To: <1563393026-17118-1-git-send-email-wahrenst@gmx.net>

From: Al Cooper <alcooperx@gmail.com>

The 7211 has a new way of selecting the pull-up/pull-down setting
for a GPIO pin. The registers used for the bcm2837, GP_PUD and
GP_PUDCLKn0, are no longer connected. A new set of registers,
GP_GPIO_PUP_PDN_CNTRL_REGx must be used. This commit will add
a new compatible string "brcm,bcm7211-gpio" and the kernel
driver will use it to select which method is used to select
pull-up/pull-down.

Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
---
 drivers/pinctrl/bcm/pinctrl-bcm2835.c | 85 ++++++++++++++++++++++++++++++++---
 1 file changed, 80 insertions(+), 5 deletions(-)

diff --git a/drivers/pinctrl/bcm/pinctrl-bcm2835.c b/drivers/pinctrl/bcm/pinctrl-bcm2835.c
index 183d1ff..35d9f95 100644
--- a/drivers/pinctrl/bcm/pinctrl-bcm2835.c
+++ b/drivers/pinctrl/bcm/pinctrl-bcm2835.c
@@ -57,15 +57,26 @@
 #define GPAFEN0		0x88	/* Pin Async Falling Edge Detect */
 #define GPPUD		0x94	/* Pin Pull-up/down Enable */
 #define GPPUDCLK0	0x98	/* Pin Pull-up/down Enable Clock */
+#define GP_GPIO_PUP_PDN_CNTRL_REG0 0xe4 /* 7211 Pin Pull-up/down select */

 #define FSEL_REG(p)		(GPFSEL0 + (((p) / 10) * 4))
 #define FSEL_SHIFT(p)		(((p) % 10) * 3)
 #define GPIO_REG_OFFSET(p)	((p) / 32)
 #define GPIO_REG_SHIFT(p)	((p) % 32)

+#define PUD_7211_MASK		0x3
+#define PUD_7211_REG_OFFSET(p)	((p) / 16)
+#define PUD_7211_REG_SHIFT(p)	(((p) % 16) * 2)
+
 /* argument: bcm2835_pinconf_pull */
 #define BCM2835_PINCONF_PARAM_PULL	(PIN_CONFIG_END + 1)

+enum bcm7211_pinconf_pull {
+	BCM7211_PINCONFIG_PULL_NONE,
+	BCM7211_PINCONFIG_PULL_UP,
+	BCM7211_PINCONFIG_PULL_DOWN,
+};
+
 struct bcm2835_pinctrl {
 	struct device *dev;
 	void __iomem *base;
@@ -975,6 +986,55 @@ static const struct pinconf_ops bcm2835_pinconf_ops = {
 	.pin_config_set = bcm2835_pinconf_set,
 };

+static int bcm7211_pinconf_set(struct pinctrl_dev *pctldev,
+			       unsigned int pin, unsigned long *configs,
+			       unsigned int num_configs)
+{
+	struct bcm2835_pinctrl *pc = pinctrl_dev_get_drvdata(pctldev);
+	u32 param, arg;
+	u32 shifter;
+	u32 value;
+	u32 off;
+	int i;
+
+	for (i = 0; i < num_configs; i++) {
+		param = pinconf_to_config_param(configs[i]);
+		if (param != BCM2835_PINCONF_PARAM_PULL)
+			return -EINVAL;
+		arg = pinconf_to_config_argument(configs[i]);
+
+		/* convert to 7211 value */
+		switch (arg) {
+		case PIN_CONFIG_BIAS_DISABLE:
+			arg = BCM7211_PINCONFIG_PULL_NONE;
+			break;
+		case PIN_CONFIG_BIAS_PULL_DOWN:
+			arg = BCM7211_PINCONFIG_PULL_DOWN;
+			break;
+		case PIN_CONFIG_BIAS_PULL_UP:
+			arg = BCM7211_PINCONFIG_PULL_UP;
+			break;
+		}
+
+		off = PUD_7211_REG_OFFSET(pin);
+		shifter = PUD_7211_REG_SHIFT(pin);
+
+		value = bcm2835_gpio_rd(pc, GP_GPIO_PUP_PDN_CNTRL_REG0 +
+					(off * 4));
+		value &= ~(PUD_7211_MASK << shifter);
+		value |= (arg << shifter);
+		bcm2835_gpio_wr(pc, GP_GPIO_PUP_PDN_CNTRL_REG0 + (off * 4),
+				value);
+	} /* for each config */
+
+	return 0;
+}
+
+static const struct pinconf_ops bcm7211_pinconf_ops = {
+	.pin_config_get = bcm2835_pinconf_get,
+	.pin_config_set = bcm7211_pinconf_set,
+};
+
 static struct pinctrl_desc bcm2835_pinctrl_desc = {
 	.name = MODULE_NAME,
 	.pins = bcm2835_gpio_pins,
@@ -990,6 +1050,18 @@ static struct pinctrl_gpio_range bcm2835_pinctrl_gpio_range = {
 	.npins = BCM2835_NUM_GPIOS,
 };

+static const struct of_device_id bcm2835_pinctrl_match[] = {
+	{
+		.compatible = "brcm,bcm2835-gpio",
+		.data = &bcm2835_pinconf_ops,
+	},
+	{
+		.compatible = "brcm,bcm7211-gpio",
+		.data = &bcm7211_pinconf_ops,
+	},
+	{}
+};
+
 static int bcm2835_pinctrl_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -997,6 +1069,8 @@ static int bcm2835_pinctrl_probe(struct platform_device *pdev)
 	struct bcm2835_pinctrl *pc;
 	struct resource iomem;
 	int err, i;
+	const struct of_device_id *match;
+
 	BUILD_BUG_ON(ARRAY_SIZE(bcm2835_gpio_pins) != BCM2835_NUM_GPIOS);
 	BUILD_BUG_ON(ARRAY_SIZE(bcm2835_gpio_groups) != BCM2835_NUM_GPIOS);

@@ -1073,6 +1147,12 @@ static int bcm2835_pinctrl_probe(struct platform_device *pdev)
 					     bcm2835_gpio_irq_handler);
 	}

+	match = of_match_node(bcm2835_pinctrl_match, pdev->dev.of_node);
+	if (match) {
+		bcm2835_pinctrl_desc.confops =
+			(const struct pinconf_ops *)match->data;
+	}
+
 	pc->pctl_dev = devm_pinctrl_register(dev, &bcm2835_pinctrl_desc, pc);
 	if (IS_ERR(pc->pctl_dev)) {
 		gpiochip_remove(&pc->gpio_chip);
@@ -1087,11 +1167,6 @@ static int bcm2835_pinctrl_probe(struct platform_device *pdev)
 	return 0;
 }

-static const struct of_device_id bcm2835_pinctrl_match[] = {
-	{ .compatible = "brcm,bcm2835-gpio" },
-	{}
-};
-
 static struct platform_driver bcm2835_pinctrl_driver = {
 	.probe = bcm2835_pinctrl_probe,
 	.driver = {
--
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

  parent reply index

Thread overview: 32+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-07-17 19:50 [PATCH RFC 00/18] ARM: Add minimal Raspberry Pi 4 support Stefan Wahren
2019-07-17 19:50 ` [PATCH RFC 01/18] ARM: bcm283x: Reduce register ranges for UART, SPI and I2C Stefan Wahren
2019-07-17 19:50 ` [PATCH RFC 02/18] ARM: bcm2835: DMA can only address 1GB Stefan Wahren
2019-07-17 19:50 ` [PATCH RFC 03/18] ARM: dts: bcm283x: Move BCM2835/6/7 specific to bcm2835-common.dtsi Stefan Wahren
2019-07-17 19:50 ` [PATCH RFC 04/18] ARM: dts: bcm283x: Define MMC interfaces at board level Stefan Wahren
2019-07-17 19:50 ` [PATCH RFC 05/18] ARM: dts: bcm283x: Define memory " Stefan Wahren
2019-07-17 19:50 ` [PATCH RFC 06/18] dt-bindings: bcm2835-cprman: Add bcm2838 support Stefan Wahren
2019-07-17 19:50 ` [PATCH RFC 07/18] clk: bcm2835: Add BCM2838_CLOCK_EMMC2 support Stefan Wahren
2019-07-18  8:47   ` Matthias Brugger
2019-07-18 16:51     ` Florian Fainelli
2019-07-18 18:37       ` Eric Anholt
2019-07-19 16:40         ` Stefan Wahren
2019-07-19 19:49           ` Eric Anholt
2019-07-17 19:50 ` [PATCH RFC 08/18] dt-bindings: sdhci-iproc: Add brcm,bcm2838-emmc2 Stefan Wahren
2019-07-17 19:50 ` [PATCH RFC 09/18] mmc: sdhci-iproc: Add support for emmc2 of the BCM2838 Stefan Wahren
2019-07-18  8:34   ` Matthias Brugger
2019-07-18 16:40     ` Florian Fainelli
2019-07-18 16:48       ` Matthias Brugger
2019-07-18 16:52         ` Florian Fainelli
2019-07-18 17:46         ` Stefan Wahren
2019-07-18 18:09         ` Stefan Wahren
2019-07-18 18:19           ` Andrei Gherzan
2019-07-17 19:50 ` Stefan Wahren [this message]
2019-08-02 22:05   ` [PATCH RFC 10/18] pinctrl: bcm2835: bcm7211: Add support for 7211 pull-up functionality Linus Walleij
2019-07-17 19:50 ` [PATCH RFC 11/18] pinctrl: bcm2835: Fix BCM7211 pinconf handling Stefan Wahren
2019-08-02 22:06   ` Linus Walleij
2019-07-17 19:50 ` [PATCH RFC 12/18] dt-bindings: pinctrl: bcm2835: Add brcm, bcm2838 compatible Stefan Wahren
2019-07-17 19:50 ` [PATCH RFC 13/18] pinctrl: bcm2835: Add BCM2838 support Stefan Wahren
2019-08-02 22:08   ` Linus Walleij
2019-07-18 18:45 ` [PATCH RFC 00/18] ARM: Add minimal Raspberry Pi 4 support Eric Anholt
2019-07-18 18:58   ` Florian Fainelli
2019-07-19 13:18   ` Nicolas Saenz Julienne

Reply instructions:

You may reply publically to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1563393026-17118-11-git-send-email-wahrenst@gmx.net \
    --to=wahrenst@gmx.net \
    --cc=adrian.hunter@intel.com \
    --cc=alcooperx@gmail.com \
    --cc=bcm-kernel-feedback-list@broadcom.com \
    --cc=broonie@kernel.org \
    --cc=eric@anholt.net \
    --cc=f.fainelli@gmail.com \
    --cc=linus.walleij@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-rpi-kernel@lists.infradead.org \
    --cc=mark.rutland@arm.com \
    --cc=mturquette@baylibre.com \
    --cc=nsaenzjulienne@suse.de \
    --cc=rjui@broadcom.com \
    --cc=robh+dt@kernel.org \
    --cc=sboyd@kernel.org \
    --cc=sbranden@broadcom.com \
    --cc=ulf.hansson@linaro.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-ARM-Kernel Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-arm-kernel/0 linux-arm-kernel/git/0.git
	git clone --mirror https://lore.kernel.org/linux-arm-kernel/1 linux-arm-kernel/git/1.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-arm-kernel linux-arm-kernel/ https://lore.kernel.org/linux-arm-kernel \
		linux-arm-kernel@lists.infradead.org
	public-inbox-index linux-arm-kernel

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.infradead.lists.linux-arm-kernel


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git