Linux-ARM-Kernel Archive on lore.kernel.org
 help / color / Atom feed
From: Anson.Huang@nxp.com
To: robh+dt@kernel.org, mark.rutland@arm.com, shawnguo@kernel.org,
	s.hauer@pengutronix.de, kernel@pengutronix.de,
	festevam@gmail.com, mturquette@baylibre.com, sboyd@kernel.org,
	rjw@rjwysocki.net, viresh.kumar@linaro.org,
	leonard.crestez@nxp.com, abel.vesa@nxp.com,
	devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org, linux-clk@vger.kernel.org,
	linux-pm@vger.kernel.org
Cc: Linux-imx@nxp.com
Subject: [PATCH 2/6] arm64: dts: imx8mn-ddr4-evk: Add rohm, bd71847 PMIC support
Date: Thu, 15 Aug 2019 06:59:39 -0400
Message-ID: <1565866783-19672-2-git-send-email-Anson.Huang@nxp.com> (raw)
In-Reply-To: <1565866783-19672-1-git-send-email-Anson.Huang@nxp.com>

From: Anson Huang <Anson.Huang@nxp.com>

On i.MX8MN DDR4 EVK board, there is a rohm,bd71847 PMIC
on i2c1 bus, enable it.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
 arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts | 109 ++++++++++++++++++++++
 1 file changed, 109 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts b/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
index 5fce5b1..10ebf77 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
@@ -57,6 +57,12 @@
 		>;
 	};
 
+	pinctrl_pmic: pmicirq {
+		fsl,pins = <
+			MX8MN_IOMUXC_GPIO1_IO03_GPIO1_IO3	0x41
+		>;
+	};
+
 	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmc {
 		fsl,pins = <
 			MX8MN_IOMUXC_SD2_RESET_B_GPIO2_IO19	0x41
@@ -194,6 +200,109 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
+
+	pmic@4b {
+		compatible = "rohm,bd71847";
+		reg = <0x4b>;
+		pinctrl-0 = <&pinctrl_pmic>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <3 GPIO_ACTIVE_LOW>;
+		rohm,reset-snvs-powered;
+
+		regulators {
+			buck1_reg: BUCK1 {
+				regulator-name = "BUCK1";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <1250>;
+			};
+
+			buck2_reg: BUCK2 {
+				regulator-name = "BUCK2";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <1250>;
+			};
+
+			buck3_reg: BUCK3 {
+				// BUCK5 in datasheet
+				regulator-name = "BUCK3";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1350000>;
+			};
+
+			buck4_reg: BUCK4 {
+				// BUCK6 in datasheet
+				regulator-name = "BUCK4";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck5_reg: BUCK5 {
+				// BUCK7 in datasheet
+				regulator-name = "BUCK5";
+				regulator-min-microvolt = <1605000>;
+				regulator-max-microvolt = <1995000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck6_reg: BUCK6 {
+				// BUCK8 in datasheet
+				regulator-name = "BUCK6";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo1_reg: LDO1 {
+				regulator-name = "LDO1";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo2_reg: LDO2 {
+				regulator-name = "LDO2";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo3_reg: LDO3 {
+				regulator-name = "LDO3";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo4_reg: LDO4 {
+				regulator-name = "LDO4";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo6_reg: LDO6 {
+				regulator-name = "LDO6";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
 };
 
 &snvs_pwrkey {
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

  reply index

Thread overview: 11+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-08-15 10:59 [PATCH 1/6] arm64: dts: imx8mn-ddr4-evk: Add i2c1 support Anson.Huang
2019-08-15 10:59 ` Anson.Huang [this message]
2019-08-15 10:59 ` [PATCH 3/6] cpufreq: Use imx-cpufreq-dt for i.MX8MN's speed grading Anson.Huang
2019-08-15 10:59 ` [PATCH 4/6] cpufreq: imx-cpufreq-dt: Add i.MX8MN support Anson.Huang
2019-08-15 10:59 ` [PATCH 5/6] clk: imx8mn: Add necessary frequency support for ARM PLL table Anson.Huang
2019-08-17  3:52   ` Stephen Boyd
2019-08-17 22:22     ` Anson Huang
2019-08-18  1:11       ` Stephen Boyd
2019-08-18  6:19         ` Anson Huang
2019-08-15 10:59 ` [PATCH 6/6] arm64: dts: imx8mn: Add cpu-freq support Anson.Huang
2019-08-15 14:12 ` [PATCH 1/6] arm64: dts: imx8mn-ddr4-evk: Add i2c1 support Leonard Crestez

Reply instructions:

You may reply publically to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1565866783-19672-2-git-send-email-Anson.Huang@nxp.com \
    --to=anson.huang@nxp.com \
    --cc=Linux-imx@nxp.com \
    --cc=abel.vesa@nxp.com \
    --cc=devicetree@vger.kernel.org \
    --cc=festevam@gmail.com \
    --cc=kernel@pengutronix.de \
    --cc=leonard.crestez@nxp.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-clk@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-pm@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=mturquette@baylibre.com \
    --cc=rjw@rjwysocki.net \
    --cc=robh+dt@kernel.org \
    --cc=s.hauer@pengutronix.de \
    --cc=sboyd@kernel.org \
    --cc=shawnguo@kernel.org \
    --cc=viresh.kumar@linaro.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-ARM-Kernel Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-arm-kernel/0 linux-arm-kernel/git/0.git
	git clone --mirror https://lore.kernel.org/linux-arm-kernel/1 linux-arm-kernel/git/1.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-arm-kernel linux-arm-kernel/ https://lore.kernel.org/linux-arm-kernel \
		linux-arm-kernel@lists.infradead.org
	public-inbox-index linux-arm-kernel

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.infradead.lists.linux-arm-kernel


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git