From: Manish Narani <manish.narani@xilinx.com>
To: ulf.hansson@linaro.org, robh+dt@kernel.org, mark.rutland@arm.com,
adrian.hunter@intel.com, michal.simek@xilinx.com,
jolly.shah@xilinx.com, nava.manne@xilinx.com,
rajan.vaja@xilinx.com, manish.narani@xilinx.com
Cc: devicetree@vger.kernel.org, linux-mmc@vger.kernel.org,
linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org, git@xilinx.com
Subject: [PATCH v5 4/8] dt-bindings: mmc: Add optional generic properties for mmc
Date: Fri, 1 Nov 2019 11:35:49 +0530 [thread overview]
Message-ID: <1572588353-110682-5-git-send-email-manish.narani@xilinx.com> (raw)
In-Reply-To: <1572588353-110682-1-git-send-email-manish.narani@xilinx.com>
Add optional properties for mmc hosts which are used to set clk delays
for different speed modes in the controller.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
---
.../bindings/mmc/mmc-controller.yaml | 92 +++++++++++++++++++
1 file changed, 92 insertions(+)
diff --git a/Documentation/devicetree/bindings/mmc/mmc-controller.yaml b/Documentation/devicetree/bindings/mmc/mmc-controller.yaml
index 080754e0ef35..87a83d966851 100644
--- a/Documentation/devicetree/bindings/mmc/mmc-controller.yaml
+++ b/Documentation/devicetree/bindings/mmc/mmc-controller.yaml
@@ -212,6 +212,98 @@ properties:
description:
eMMC HS400 enhanced strobe mode is supported
+ # Below mentioned are the clock (phase) delays which are to be configured
+ # in the controller while switching to particular speed mode. The range
+ # of values are 0 to 359 degrees.
+
+ clk-phase-legacy:
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ - minimum: 0
+ - maximum: 359
+ description:
+ Input/Output Clock Delay pair in degrees for Legacy Mode.
+
+ clk-phase-mmc-hs:
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ - minimum: 0
+ - maximum: 359
+ description:
+ Input/Output Clock Delay pair degrees for MMC HS.
+
+ clk-phase-sd-hs:
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ - minimum: 0
+ - maximum: 359
+ description:
+ Input/Output Clock Delay pair in degrees for SD HS.
+
+ clk-phase-uhs-sdr12:
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ - minimum: 0
+ - maximum: 359
+ description:
+ Input/Output Clock Delay pair in degrees for SDR12.
+
+ clk-phase-uhs-sdr25:
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ - minimum: 0
+ - maximum: 359
+ description:
+ Input/Output Clock Delay pair in degrees for SDR25.
+
+ clk-phase-uhs-sdr50:
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ - minimum: 0
+ - maximum: 359
+ description:
+ Input/Output Clock Delay pair in degrees for SDR50.
+
+ clk-phase-uhs-sdr104:
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ - minimum: 0
+ - maximum: 359
+ description:
+ Input/Output Clock Delay pair in degrees for SDR104.
+
+ clk-phase-uhs-ddr50:
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ - minimum: 0
+ - maximum: 359
+ description:
+ Input/Output Clock Delay pair in degrees for SD DDR50.
+
+ clk-phase-mmc-ddr52:
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ - minimum: 0
+ - maximum: 359
+ description:
+ Input/Output Clock Delay pair in degrees for MMC DDR52.
+
+ clk-phase-mmc-hs200:
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ - minimum: 0
+ - maximum: 359
+ description:
+ Input/Output Clock Delay pair in degrees for MMC HS200.
+
+ clk-phase-mmc-hs400:
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ - minimum: 0
+ - maximum: 359
+ description:
+ Input/Output Clock Delay pair in degrees for MMC HS400.
+
dsr:
allOf:
- $ref: /schemas/types.yaml#/definitions/uint32
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2019-11-01 6:07 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-11-01 6:05 [PATCH v5 0/8] Arasan SDHCI enhancements and ZynqMP Tap Delays Handling Manish Narani
2019-11-01 6:05 ` [PATCH v5 1/8] mmc: sdhci-of-arasan: Separate out clk related data to another structure Manish Narani
2019-11-01 6:05 ` [PATCH v5 2/8] dt-bindings: mmc: arasan: Update Documentation for the input clock Manish Narani
2019-11-01 6:05 ` [PATCH v5 3/8] mmc: sdhci-of-arasan: Add sampling clock for a phy to use Manish Narani
2019-11-01 6:05 ` Manish Narani [this message]
2019-11-04 23:14 ` [PATCH v5 4/8] dt-bindings: mmc: Add optional generic properties for mmc Rob Herring
2019-11-11 10:07 ` Manish Narani
2019-11-18 3:55 ` Manish Narani
2019-11-18 14:44 ` Rob Herring
2019-11-01 6:05 ` [PATCH v5 5/8] mmc: sdhci-of-arasan: Add support to set clock phase delays for SD Manish Narani
2019-11-01 6:05 ` [PATCH v5 6/8] firmware: xilinx: Add SDIO Tap Delay nodes Manish Narani
2019-11-01 6:05 ` [PATCH v5 7/8] dt-bindings: mmc: arasan: Document 'xlnx, zynqmp-8.9a' controller Manish Narani
2019-11-01 6:05 ` [PATCH v5 8/8] mmc: sdhci-of-arasan: Add support for ZynqMP Platform Tap Delays Setup Manish Narani
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1572588353-110682-5-git-send-email-manish.narani@xilinx.com \
--to=manish.narani@xilinx.com \
--cc=adrian.hunter@intel.com \
--cc=devicetree@vger.kernel.org \
--cc=git@xilinx.com \
--cc=jolly.shah@xilinx.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=michal.simek@xilinx.com \
--cc=nava.manne@xilinx.com \
--cc=rajan.vaja@xilinx.com \
--cc=robh+dt@kernel.org \
--cc=ulf.hansson@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).