From: Sricharan R <sricharan@codeaurora.org>
To: agross@kernel.org, devicetree@vger.kernel.org,
linus.walleij@linaro.org, linux-arm-kernel@lists.infradead.org,
linux-arm-msm@vger.kernel.org, linux-gpio@vger.kernel.org,
linux-kernel@vger.kernel.org, linux-soc@vger.kernel.org,
robh+dt@kernel.org, sivaprak@codeaurora.org,
sricharan@codeaurora.org
Subject: [PATCH V5 0/5] Add minimal boot support for IPQ6018
Date: Thu, 16 Jan 2020 13:14:56 +0530 [thread overview]
Message-ID: <1579160701-32408-1-git-send-email-sricharan@codeaurora.org> (raw)
The IPQ6018 is Qualcomm\u2019s 802.11ax SoC for Routers,
Gateways and Access Points.
This series adds minimal board boot support for ipq6018-cp01 board.
[V5]
* Addressed review comments in pinctrl bindings from Rob.
* Ran make dt_binding_check with modified patch.
* Added fixed rate clocks in gcc clock controller node.
* Patch 4 arm64: dts: Add ipq6018 SoC and CP01 board support has build
dependency with,
https://lkml.org/lkml/2020/1/9/84
[v4]
* Addressed review comments in pinctrl bindings from Rob.
* Ran make dt_binding_check and no issues was reported.
* Deleted absahu email id from patch 4, since its bouncing now.
* Patch 4 arm64: dts: Add ipq6018 SoC and CP01 board support has build
dependency with,
https://lkml.org/lkml/2020/1/9/84
[V3]
* Removed clock driver and bindings from this patch series, and added them
as a different series.
* Removed qpic_padN from pinctrl driver.
* Addressed review comments in dts, and added the remaining fixed clocks their
* Fixed review comments in pinctrl bindings
[v2]
* Splitted dt bindings and driver into different patches. Added missing bindings
and some style changes.
* Added ipq6018 schema
* Addressed review comments for gcc clock bindings.
* Removed all clk critical flags, removed 1/1 factor clocks, moved to new
way of specifying clk parents, and addressed other review comments.
* Sorted nodes based on address, name, label. Removed unused clock nodes,
Addressed other review comments.
Sricharan R (5):
dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings
pinctrl: qcom: Add ipq6018 pinctrl driver
dt-bindings: qcom: Add ipq6018 bindings
arm64: dts: Add ipq6018 SoC and CP01 board support
arm64: defconfig: Enable qcom ipq6018 clock and pinctrl
Documentation/devicetree/bindings/arm/qcom.yaml | 8 +
.../bindings/pinctrl/qcom,ipq6018-pinctrl.yaml | 174 +++
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts | 30 +
arch/arm64/boot/dts/qcom/ipq6018.dtsi | 263 +++++
arch/arm64/configs/defconfig | 3 +
drivers/pinctrl/qcom/Kconfig | 10 +
drivers/pinctrl/qcom/Makefile | 1 +
drivers/pinctrl/qcom/pinctrl-ipq6018.c | 1107 ++++++++++++++++++++
9 files changed, 1597 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
create mode 100644 arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
create mode 100644 arch/arm64/boot/dts/qcom/ipq6018.dtsi
create mode 100644 drivers/pinctrl/qcom/pinctrl-ipq6018.c
--
1.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next reply other threads:[~2020-01-16 7:45 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-01-16 7:44 Sricharan R [this message]
2020-01-16 7:44 ` [PATCH V5 1/5] dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings Sricharan R
2020-01-17 16:01 ` Rob Herring
2020-01-19 13:15 ` Sricharan R
2020-01-16 7:44 ` [PATCH V5 2/5] pinctrl: qcom: Add ipq6018 pinctrl driver Sricharan R
2020-01-16 7:44 ` [PATCH V5 3/5] dt-bindings: qcom: Add ipq6018 bindings Sricharan R
2020-01-16 7:45 ` [PATCH V5 4/5] arm64: dts: Add ipq6018 SoC and CP01 board support Sricharan R
2020-01-16 7:45 ` [PATCH V5 5/5] arm64: defconfig: Enable qcom ipq6018 clock and pinctrl Sricharan R
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1579160701-32408-1-git-send-email-sricharan@codeaurora.org \
--to=sricharan@codeaurora.org \
--cc=agross@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-soc@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=sivaprak@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).