From: Li Jun <jun.li@nxp.com>
To: heikki.krogerus@linux.intel.com, robh+dt@kernel.org, shawnguo@kernel.org
Cc: gregkh@linuxfoundation.org, linux@roeck-us.net,
linux-usb@vger.kernel.org, linux-imx@nxp.com, jun.li@nxp.com,
devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org
Subject: [PATCH 4/4] arm64: dts: imx8mp-evk: enable usb0 with typec connector
Date: Wed, 19 May 2021 15:14:50 +0800 [thread overview]
Message-ID: <1621408490-23811-5-git-send-email-jun.li@nxp.com> (raw)
In-Reply-To: <1621408490-23811-1-git-send-email-jun.li@nxp.com>
The first usb port on imx8mp evk board has typec connector,
it has dual data role and dual power role with power delivery
support.
Signed-off-by: Li Jun <jun.li@nxp.com>
---
arch/arm64/boot/dts/freescale/imx8mp-evk.dts | 110 +++++++++++++++++++
1 file changed, 110 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-evk.dts b/arch/arm64/boot/dts/freescale/imx8mp-evk.dts
index 2c28e589677e..c69514910eb9 100644
--- a/arch/arm64/boot/dts/freescale/imx8mp-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mp-evk.dts
@@ -5,6 +5,7 @@
/dts-v1/;
+#include <dt-bindings/usb/pd.h>
#include "imx8mp.dtsi"
/ {
@@ -65,6 +66,22 @@ reg_usdhc2_vmmc: regulator-usdhc2 {
gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
+
+ mux: mux-controller {
+ compatible = "gpio-mux";
+ #mux-control-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_typec_mux>;
+ mux-gpios = <&gpio4 20 GPIO_ACTIVE_HIGH>,
+ <&gpio2 20 GPIO_ACTIVE_HIGH>;
+ idle-state = <2>;
+
+ port {
+ usb3_data_ss: endpoint {
+ remote-endpoint = <&typec_con_ss>;
+ };
+ };
+ };
};
&flexcan1 {
@@ -104,6 +121,56 @@ ethphy1: ethernet-phy@1 {
};
};
+&i2c2 {
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+
+ ptn5110: tcpc@50 {
+ compatible = "nxp,ptn5110";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_typec>;
+ reg = <0x50>;
+ interrupt-parent = <&gpio4>;
+ interrupts = <19 8>;
+
+ port {
+ typec_dr_sw: endpoint {
+ remote-endpoint = <&usb3_drd_sw>;
+ };
+ };
+
+ usb_con: connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ power-role = "dual";
+ data-role = "dual";
+ try-power-role = "sink";
+ source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+ sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
+ PDO_VAR(5000, 20000, 3000)>;
+ op-sink-microwatt = <15000000>;
+ self-powered;
+ mux-controls = <&mux>;
+ mux-control-names = "typec-orientation-switch";
+ mux-control-switch-states = <2>, <0>, <1>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@1 {
+ reg = <1>;
+ typec_con_ss: endpoint {
+ remote-endpoint = <&usb3_data_ss>;
+ };
+ };
+ };
+ };
+ };
+};
+
&i2c3 {
clock-frequency = <400000>;
pinctrl-names = "default";
@@ -137,6 +204,29 @@ &usb3_1 {
status = "okay";
};
+&usb3_phy0 {
+ status = "okay";
+};
+
+&usb3_0 {
+ status = "okay";
+};
+
+&usb_dwc3_0 {
+ dr_mode = "otg";
+ hnp-disable;
+ srp-disable;
+ adp-disable;
+ usb-role-switch;
+ status = "okay";
+
+ port {
+ usb3_drd_sw: endpoint {
+ remote-endpoint = <&typec_dr_sw>;
+ };
+ };
+};
+
&usb_dwc3_1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usb1_vbus>;
@@ -229,6 +319,13 @@ MX8MP_IOMUXC_NAND_READY_B__GPIO3_IO16 0x19
>;
};
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL 0x400001c3
+ MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA 0x400001c3
+ >;
+ };
+
pinctrl_i2c3: i2c3grp {
fsl,pins = <
MX8MP_IOMUXC_I2C3_SCL__I2C3_SCL 0x400001c3
@@ -242,6 +339,19 @@ MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19 0x41
>;
};
+ pinctrl_typec: typec1grp {
+ fsl,pins = <
+ MX8MP_IOMUXC_SAI1_TXD7__GPIO4_IO19 0x1c4
+ >;
+ };
+
+ pinctrl_typec_mux: typec1muxgrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_SAI1_MCLK__GPIO4_IO20 0x16
+ MX8MP_IOMUXC_SD2_WP__GPIO2_IO20 0x16
+ >;
+ };
+
pinctrl_uart2: uart2grp {
fsl,pins = <
MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX 0x49
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
prev parent reply other threads:[~2021-05-19 7:34 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-05-19 7:14 [PATCH 0/4] typec switch via mux controller Li Jun
2021-05-19 7:14 ` [PATCH 1/4] dt-bindings: connector: Add typec orientation switch properties Li Jun
2021-05-21 1:30 ` Rob Herring
2021-05-25 11:48 ` Jun Li
2021-05-19 7:14 ` [PATCH 2/4] usb: typec: use typec cap fwnode's of_node for typec port Li Jun
2021-05-20 12:38 ` Heikki Krogerus
2021-05-19 7:14 ` [PATCH 3/4] usb: typec: add typec orientation switch support via mux controller Li Jun
2021-05-20 12:33 ` Heikki Krogerus
2021-05-21 8:37 ` Heikki Krogerus
2021-05-25 11:46 ` Jun Li
2021-05-26 9:16 ` Heikki Krogerus
2021-05-31 11:58 ` Jun Li
2021-05-21 13:02 ` Jun Li
2021-05-19 7:14 ` Li Jun [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1621408490-23811-5-git-send-email-jun.li@nxp.com \
--to=jun.li@nxp.com \
--cc=devicetree@vger.kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=heikki.krogerus@linux.intel.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-imx@nxp.com \
--cc=linux-usb@vger.kernel.org \
--cc=linux@roeck-us.net \
--cc=robh+dt@kernel.org \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).