Re: [PATCH v2 3/3] clk: meson: a1: add support for Amlogic A1 clock driver

[Jerome Brunet <jbrunet@baylibre.com>]

On Fri 25 Oct 2019 at 13:32, Jian Hu <jian.hu@amlogic.com> wrote:

> Hi, Jerome
>
> Thanks for your review
>
> On 2019/10/21 19:41, Jerome Brunet wrote:
>>
>> On Fri 18 Oct 2019 at 09:14, Jian Hu <jian.hu@amlogic.com> wrote:
>>
>>> The Amlogic A1 clock includes three drivers:
>>> peripheral clocks, pll clocks, CPU clocks.
>>> sys pll and CPU clocks will be sent in next patch.
>>>
>>> Unlike the previous series, there is no EE/AO domain
>>> in A1 CLK controllers.
>>>
>>> Signed-off-by: Jian Hu <jian.hu@amlogic.com>
>>> ---
>>>   drivers/clk/meson/Kconfig  |   10 +
>>>   drivers/clk/meson/Makefile |    1 +
>>>   drivers/clk/meson/a1-pll.c |  345 +++++++
>>>   drivers/clk/meson/a1-pll.h |   56 ++
>>>   drivers/clk/meson/a1.c     | 2264 ++++++++++++++++++++++++++++++++++++++++++++
>>>   drivers/clk/meson/a1.h     |  120 +++
>>>   6 files changed, 2796 insertions(+)
>>>   create mode 100644 drivers/clk/meson/a1-pll.c
>>>   create mode 100644 drivers/clk/meson/a1-pll.h
>>>   create mode 100644 drivers/clk/meson/a1.c
>>>   create mode 100644 drivers/clk/meson/a1.h
>>
>> In the next version, one
> OK, I will send a1 peripheral and pll driver in two patch.
>>
>>>
>>> diff --git a/drivers/clk/meson/Kconfig b/drivers/clk/meson/Kconfig
>>> index dabeb43..c2809b2 100644
>>> --- a/drivers/clk/meson/Kconfig
>>> +++ b/drivers/clk/meson/Kconfig
>>> @@ -93,6 +93,16 @@ config COMMON_CLK_AXG_AUDIO
>>>   	  Support for the audio clock controller on AmLogic A113D devices,
>>>   	  aka axg, Say Y if you want audio subsystem to work.
>>>   +config COMMON_CLK_A1
>>> +	bool
>>> +	depends on ARCH_MESON
>>> +	select COMMON_CLK_MESON_REGMAP
>>> +	select COMMON_CLK_MESON_DUALDIV
>>> +	select COMMON_CLK_MESON_PLL
>>> +	help
>>> +	  Support for the clock controller on Amlogic A113L device,
>>> +	  aka a1. Say Y if you want peripherals to work.
>>> +
>>>   config COMMON_CLK_G12A
>>>   	bool
>>>   	depends on ARCH_MESON
>>> diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
>>> index 3939f21..28cbae1 100644
>>> --- a/drivers/clk/meson/Makefile
>>> +++ b/drivers/clk/meson/Makefile
>>> @@ -16,6 +16,7 @@ obj-$(CONFIG_COMMON_CLK_MESON_VID_PLL_DIV) += vid-pll-div.o
>>>     obj-$(CONFIG_COMMON_CLK_AXG) += axg.o axg-aoclk.o
>>>   obj-$(CONFIG_COMMON_CLK_AXG_AUDIO) += axg-audio.o
>>> +obj-$(CONFIG_COMMON_CLK_A1) += a1-pll.o a1.o
>>
>> So far, all the controller had there own option, I don't see why it
>> should be different here.
>>
> OK, I will add the other option CONFIG_COMMON_CLK_A1_PLL for pll driver
>>>   obj-$(CONFIG_COMMON_CLK_GXBB) += gxbb.o gxbb-aoclk.o
>>>   obj-$(CONFIG_COMMON_CLK_G12A) += g12a.o g12a-aoclk.o
>>>   obj-$(CONFIG_COMMON_CLK_MESON8B) += meson8b.o
>>> diff --git a/drivers/clk/meson/a1-pll.c b/drivers/clk/meson/a1-pll.c
>>> new file mode 100644
>>> index 0000000..486d964
>>> --- /dev/null
>>> +++ b/drivers/clk/meson/a1-pll.c
>>> @@ -0,0 +1,345 @@
>>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>>> +/*
>>> + * Copyright (c) 2019 Amlogic, Inc. All rights reserved.
>>> + * Author: Jian Hu <jian.hu@amlogic.com>
>>> + */
>>> +
>>> +#include <linux/platform_device.h>
>>
>> Hum ... looks like some things are missing here
>>
>> #include <linux/of_device.h>
>> #include <linux/clk-provider.h>
>>
>> ?
> #1
> There is <linux/clk-provider.h> in meson-eeclk.h file,
>
> and for A1 driver(a1.c/a1-pll.c) the head file is not requied.
>
> #2
> For A1 driver, the file "linux/of_device.h" is not required.
> It is required by meson-eeclk.c in fact.

You are using what is provided by these headers directly in this file
If meson-eeclk ever changes, your driver breaks

>>
>>> +#include "clk-pll.h"
>>> +#include "meson-eeclk.h"
>>> +#include "a1-pll.h"
>>
>> Alphanumeric order please
>>
> OK, I will change it in the next version.
>
>>> +
>>> +static struct clk_regmap a1_fixed_pll_dco = {
>>> +	.data = &(struct meson_clk_pll_data){
>>> +		.en = {
>>> +			.reg_off = ANACTRL_FIXPLL_CTRL0,
>>> +			.shift   = 28,
>>> +			.width   = 1,
>>> +		},
>>> +		.m = {
>>> +			.reg_off = ANACTRL_FIXPLL_CTRL0,
>>> +			.shift   = 0,
>>> +			.width   = 8,
>>> +		},
>>> +		.n = {
>>> +			.reg_off = ANACTRL_FIXPLL_CTRL0,
>>> +			.shift   = 10,
>>> +			.width   = 5,
>>> +		},
>>> +		.frac = {
>>> +			.reg_off = ANACTRL_FIXPLL_CTRL1,
>>> +			.shift   = 0,
>>> +			.width   = 19,
>>> +		},
>>> +		.l = {
>>> +			.reg_off = ANACTRL_FIXPLL_CTRL0,
>>> +			.shift   = 31,
>>> +			.width   = 1,
>>> +		},
>>> +		.rst = {
>>> +			.reg_off = ANACTRL_FIXPLL_CTRL0,
>>> +			.shift   = 29,
>>> +			.width   = 1,
>>> +		},
>>> +	},
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "fixed_pll_dco",
>>> +		.ops = &meson_clk_pll_ro_ops,
>>> +		.parent_data = &(const struct clk_parent_data){
>>> +			.fw_name = "xtal_fixpll",
>>> +			.name = "xtal_fixpll",
>>> +		},
>>> +		.num_parents = 1,
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_fixed_pll = {
>>> +	.data = &(struct clk_regmap_gate_data){
>>> +		.offset = ANACTRL_FIXPLL_CTRL0,
>>> +		.bit_idx = 20,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data) {
>>> +		.name = "fixed_pll",
>>> +		.ops = &clk_regmap_gate_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_fixed_pll_dco.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +		/*
>>> +		 * This clock is fclk_div2/3/4's parent,
>>> +		 * However, fclk_div2/3/5 feeds AXI/APB/DDR.
>>
>> is it fclk_div2/3/4 or fclk_div2/3/5 ?
>>
>>> +		 * It is required by the platform to operate correctly.
>>> +		 * Until the following condition are met, we need this clock to
>>> +		 * be marked as critical:
>>> +		 * a) Mark the clock used by a firmware resource, if possible
>>> +		 * b) CCF has a clock hand-off mechanism to make the sure the
>>> +		 *    clock stays on until the proper driver comes along
>>> +		 */
>>
>> Don't blindly copy/paste comments from other drivers. There is no driver
>> for the devices you are mentionning so the end of the comment is
>> confusing. The 3 first lines were enough
>>
> OK, I will remove the confusing comments
>
>>> +		.flags = CLK_IS_CRITICAL,
>>
>>>From your comment, I understand that some child are critical, not this
>> particular (or at least, not directly). So this can be removed AFAICT
>>
>> You should even need CLK_IGNORE_UNUSED for this one since the clock will
>> already be enabled before the late_init() kicks in
>>
> OK, I will replace it as CLK_IGNORE_UNUSED.
>>> +	},
>>> +};
>>> +
>>> +static const struct pll_mult_range a1_hifi_pll_mult_range = {
>>> +	.min = 32,
>>> +	.max = 64,
>>> +};
>>> +
>>> +static const struct reg_sequence a1_hifi_init_regs[] = {
>>> +	{ .reg = ANACTRL_HIFIPLL_CTRL1, .def = 0x01800000 },
>>> +	{ .reg = ANACTRL_HIFIPLL_CTRL2, .def = 0x00001100 },
>>> +	{ .reg = ANACTRL_HIFIPLL_CTRL3, .def = 0x100a1100 },
>>> +	{ .reg = ANACTRL_HIFIPLL_CTRL4, .def = 0x00302000 },
>>> +	{ .reg = ANACTRL_HIFIPLL_CTRL0, .def = 0x01f18440 },
>>> +	{ .reg = ANACTRL_HIFIPLL_CTRL0, .def = 0x11f18440, .delay_us = 10 },
>>> +	{ .reg = ANACTRL_HIFIPLL_CTRL0, .def = 0x15f18440, .delay_us = 40 },
>>> +	{ .reg = ANACTRL_HIFIPLL_CTRL2, .def = 0x00001140 },
>>> +	{ .reg = ANACTRL_HIFIPLL_CTRL2, .def = 0x00001100 },
>>> +};
>>> +
>>> +static struct clk_regmap a1_hifi_pll = {
>>> +	.data = &(struct meson_clk_pll_data){
>>> +		.en = {
>>> +			.reg_off = ANACTRL_HIFIPLL_CTRL0,
>>> +			.shift   = 28,
>>> +			.width   = 1,
>>> +		},
>>> +		.m = {
>>> +			.reg_off = ANACTRL_HIFIPLL_CTRL0,
>>> +			.shift   = 0,
>>> +			.width   = 8,
>>> +		},
>>> +		.n = {
>>> +			.reg_off = ANACTRL_HIFIPLL_CTRL0,
>>> +			.shift   = 10,
>>> +			.width   = 5,
>>> +		},
>>> +		.frac = {
>>> +			.reg_off = ANACTRL_HIFIPLL_CTRL1,
>>> +			.shift   = 0,
>>> +			.width   = 19,
>>> +		},
>>> +		.l = {
>>> +			.reg_off = ANACTRL_HIFIPLL_STS,
>>> +			.shift   = 31,
>>> +			.width   = 1,
>>> +		},
>>> +		.range = &a1_hifi_pll_mult_range,
>>> +		.init_regs = a1_hifi_init_regs,
>>> +		.init_count = ARRAY_SIZE(a1_hifi_init_regs),
>>> +		.strict_sequence = true,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "hifi_pll",
>>> +		.ops = &meson_clk_pll_ops,
>>> +		.parent_data = &(const struct clk_parent_data){
>>> +			.fw_name = "xtal_fixpll",
>>> +			.name = "xtal_fixpll",
>>
>> Both should provided when a controller transition from the old way of
>> describing parent to the new way. This is a new controller so it does
>> not apply.
> I do not understand why it does not apply, could you explain more?

Your driver is new, it is not something old transitioning from global
name to clock in DT !

>
> The xtal_fixpll clock is registered in another peripheral driver, If do not
> desribe the "name" member in parent_data, "fw_name" does not work because
> it has not been registered. the hifi_pll parent will be null in
> /sys/kernel/debug/clk/hifi_pll/clk_parent.
>
> HIFI PLL will be a orphan clock, but its parent should be xtal_fixpll.

There will be an orphan yes, temporarily, until both controllers are up.
Once both controller are up, the clock will be reparented if necessary.

>
> So both of "fw_name" of "name" should be described.

No

>
>>
>> Same for the other occurences.
>>
>> Also, I think you meant xtal_hifipll
> Yes,I will correct it.
>>
>>> +		},
>>> +		.num_parents = 1,
>>> +	},
>>> +};
>>> +
>>> +static struct clk_fixed_factor a1_fclk_div2_div = {
>>> +	.mult = 1,
>>> +	.div = 2,
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "fclk_div2_div",
>>> +		.ops = &clk_fixed_factor_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_fixed_pll.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_fclk_div2 = {
>>> +	.data = &(struct clk_regmap_gate_data){
>>> +		.offset = ANACTRL_FIXPLL_CTRL0,
>>> +		.bit_idx = 21,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "fclk_div2",
>>> +		.ops = &clk_regmap_gate_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_fclk_div2_div.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +		/*
>>> +		 * This clock is used by DDR clock in BL2 firmware
>>> +		 * and is required by the platform to operate correctly.
>>> +		 * Until the following condition are met, we need this clock to
>>> +		 * be marked as critical:
>>> +		 * a) Mark the clock used by a firmware resource, if possible
>>> +		 * b) CCF has a clock hand-off mechanism to make the sure the
>>> +		 *    clock stays on until the proper driver comes along
>>> +		 */
>>> +		.flags = CLK_IS_CRITICAL,
>>> +	},
>>> +};
>>> +
>>> +static struct clk_fixed_factor a1_fclk_div3_div = {
>>> +	.mult = 1,
>>> +	.div = 3,
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "fclk_div3_div",
>>> +		.ops = &clk_fixed_factor_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_fixed_pll.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_fclk_div3 = {
>>> +	.data = &(struct clk_regmap_gate_data){
>>> +		.offset = ANACTRL_FIXPLL_CTRL0,
>>> +		.bit_idx = 22,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "fclk_div3",
>>> +		.ops = &clk_regmap_gate_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_fclk_div3_div.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +		/*
>>> +		 * This clock is used by APB bus which setted in Romcode
>>> +		 * and is required by the platform to operate correctly.
>>> +		 * Until the following condition are met, we need this clock to
>>> +		 * be marked as critical:
>>> +		 * a) Mark the clock used by a firmware resource, if possible
>>> +		 * b) CCF has a clock hand-off mechanism to make the sure the
>>> +		 *    clock stays on until the proper driver comes along
>>> +		 */
>>> +		.flags = CLK_IS_CRITICAL,
>>> +	},
>>> +};
>>> +
>>> +static struct clk_fixed_factor a1_fclk_div5_div = {
>>> +	.mult = 1,
>>> +	.div = 5,
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "fclk_div5_div",
>>> +		.ops = &clk_fixed_factor_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_fixed_pll.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_fclk_div5 = {
>>> +	.data = &(struct clk_regmap_gate_data){
>>> +		.offset = ANACTRL_FIXPLL_CTRL0,
>>> +		.bit_idx = 23,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "fclk_div5",
>>> +		.ops = &clk_regmap_gate_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_fclk_div5_div.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +		/*
>>> +		 * This clock is used by AXI bus which setted in Romcode
>>> +		 * and is required by the platform to operate correctly.
>>> +		 * Until the following condition are met, we need this clock to
>>> +		 * be marked as critical:
>>> +		 * a) Mark the clock used by a firmware resource, if possible
>>> +		 * b) CCF has a clock hand-off mechanism to make the sure the
>>> +		 *    clock stays on until the proper driver comes along
>>> +		 */
>>> +		.flags = CLK_IS_CRITICAL,
>>> +	},
>>> +};
>>> +
>>> +static struct clk_fixed_factor a1_fclk_div7_div = {
>>> +	.mult = 1,
>>> +	.div = 7,
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "fclk_div7_div",
>>> +		.ops = &clk_fixed_factor_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_fixed_pll.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_fclk_div7 = {
>>> +	.data = &(struct clk_regmap_gate_data){
>>> +		.offset = ANACTRL_FIXPLL_CTRL0,
>>> +		.bit_idx = 24,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "fclk_div7",
>>> +		.ops = &clk_regmap_gate_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_fclk_div7_div.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +	},
>>> +};
>>> +
>>> +/* Array of all clocks provided by this provider */
>>> +static struct clk_hw_onecell_data a1_pll_hw_onecell_data = {
>>> +	.hws = {
>>> +		[CLKID_FIXED_PLL_DCO]		= &a1_fixed_pll_dco.hw,
>>> +		[CLKID_FIXED_PLL]		= &a1_fixed_pll.hw,
>>> +		[CLKID_HIFI_PLL]		= &a1_hifi_pll.hw,
>>> +		[CLKID_FCLK_DIV2]		= &a1_fclk_div2.hw,
>>> +		[CLKID_FCLK_DIV3]		= &a1_fclk_div3.hw,
>>> +		[CLKID_FCLK_DIV5]		= &a1_fclk_div5.hw,
>>> +		[CLKID_FCLK_DIV7]		= &a1_fclk_div7.hw,
>>> +		[CLKID_FCLK_DIV2_DIV]		= &a1_fclk_div2_div.hw,
>>> +		[CLKID_FCLK_DIV3_DIV]		= &a1_fclk_div3_div.hw,
>>> +		[CLKID_FCLK_DIV5_DIV]		= &a1_fclk_div5_div.hw,
>>> +		[CLKID_FCLK_DIV7_DIV]		= &a1_fclk_div7_div.hw,
>>> +		[NR_PLL_CLKS]			= NULL,
>>> +	},
>>> +	.num = NR_PLL_CLKS,
>>> +};
>>> +
>>> +static struct clk_regmap *const a1_pll_regmaps[] = {
>>> +	&a1_fixed_pll_dco,
>>> +	&a1_fixed_pll,
>>> +	&a1_hifi_pll,
>>> +	&a1_fclk_div2,
>>> +	&a1_fclk_div3,
>>> +	&a1_fclk_div5,
>>> +	&a1_fclk_div7,
>>> +};
>>> +
>>> +static int meson_a1_pll_probe(struct platform_device *pdev)
>>> +{
>>> +	int ret;
>>> +
>>> +	ret = meson_eeclkc_probe(pdev);
>>> +	if (ret)
>>> +		return ret;
>>> +
>>> +	return 0;
>>> +}
>>
>> This function is useless.
>>
> OK, I will use meson_eeclkc_probe derectly.
>>> +
>>> +static const struct meson_eeclkc_data a1_pll_data = {
>>> +		.regmap_clks = a1_pll_regmaps,
>>> +		.regmap_clk_num = ARRAY_SIZE(a1_pll_regmaps),
>>> +		.hw_onecell_data = &a1_pll_hw_onecell_data,
>>> +};
>>> +static const struct of_device_id clkc_match_table[] = {
>>> +	{
>>> +		.compatible = "amlogic,a1-pll-clkc",
>>> +		.data = &a1_pll_data
>>> +	},
>>> +	{ /* sentinel */ }
>>
>> Nitpick: don't need to write this, just write the line like this
>>
> OK, remove it.
>> ' }, {}'
>>
>>> +};
>>> +
>>> +static struct platform_driver a1_driver = {
>>> +	.probe		= meson_a1_pll_probe,
>>> +	.driver		= {
>>> +		.name	= "a1-pll-clkc",
>>> +		.of_match_table = clkc_match_table,
>>> +	},
>>> +};
>>> +
>>> +builtin_platform_driver(a1_driver);
>>> diff --git a/drivers/clk/meson/a1-pll.h b/drivers/clk/meson/a1-pll.h
>>> new file mode 100644
>>> index 0000000..99ee2a9
>>> --- /dev/null
>>> +++ b/drivers/clk/meson/a1-pll.h
>>> @@ -0,0 +1,56 @@
>>> +/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
>>> +/*
>>> + * Copyright (c) 2019 Amlogic, Inc. All rights reserved.
>>> + */
>>> +
>>> +#ifndef __A1_PLL_H
>>> +#define __A1_PLL_H
>>> +
>>> +/* PLL register offset */
>>> +#define ANACTRL_FIXPLL_CTRL0		0x80
>>> +#define ANACTRL_FIXPLL_CTRL1		0x84
>>> +#define ANACTRL_FIXPLL_CTRL2		0x88
>>> +#define ANACTRL_FIXPLL_CTRL3		0x8c
>>> +#define ANACTRL_FIXPLL_CTRL4		0x90
>>> +#define ANACTRL_FIXPLL_STS		0x94
>>> +#define ANACTRL_SYSPLL_CTRL0		0x100
>>> +#define ANACTRL_SYSPLL_CTRL1		0x104
>>> +#define ANACTRL_SYSPLL_CTRL2		0x108
>>> +#define ANACTRL_SYSPLL_CTRL3		0x10c
>>> +#define ANACTRL_SYSPLL_CTRL4		0x110
>>> +#define ANACTRL_SYSPLL_STS		0x114
>>> +#define ANACTRL_HIFIPLL_CTRL0		0x140
>>> +#define ANACTRL_HIFIPLL_CTRL1		0x144
>>> +#define ANACTRL_HIFIPLL_CTRL2		0x148
>>> +#define ANACTRL_HIFIPLL_CTRL3		0x14c
>>> +#define ANACTRL_HIFIPLL_CTRL4		0x150
>>> +#define ANACTRL_HIFIPLL_STS		0x154
>>> +#define ANACTRL_AUDDDS_CTRL0		0x180
>>> +#define ANACTRL_AUDDDS_CTRL1		0x184
>>> +#define ANACTRL_AUDDDS_CTRL2		0x188
>>> +#define ANACTRL_AUDDDS_CTRL3		0x18c
>>> +#define ANACTRL_AUDDDS_CTRL4		0x190
>>> +#define ANACTRL_AUDDDS_STS		0x194
>>> +#define ANACTRL_MISCTOP_CTRL0		0x1c0
>>> +#define ANACTRL_POR_CNTL		0x208
>>> +
>>> +/*
>>> + * CLKID index values
>>> + *
>>> + * These indices are entirely contrived and do not map onto the hardware.
>>> + * It has now been decided to expose everything by default in the DT header:
>>> + * include/dt-bindings/clock/a1-pll-clkc.h. Only the clocks ids we don't want
>>> + * to expose, such as the internal muxes and dividers of composite clocks,
>>> + * will remain defined here.
>>> + */
>>> +#define CLKID_FIXED_PLL_DCO		0
>>> +#define CLKID_FCLK_DIV2_DIV		2
>>> +#define CLKID_FCLK_DIV3_DIV		3
>>> +#define CLKID_FCLK_DIV5_DIV		4
>>> +#define CLKID_FCLK_DIV7_DIV		5
>>> +#define NR_PLL_CLKS			11
>>> +
>>> +/* include the CLKIDs that have been made part of the DT binding */
>>> +#include <dt-bindings/clock/a1-pll-clkc.h>
>>> +
>>> +#endif /* __A1_PLL_H */
>>> diff --git a/drivers/clk/meson/a1.c b/drivers/clk/meson/a1.c
>>> new file mode 100644
>>> index 0000000..86a4733
>>> --- /dev/null
>>> +++ b/drivers/clk/meson/a1.c
>>> @@ -0,0 +1,2264 @@
>>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>>> +/*
>>> + * Copyright (c) 2019 Amlogic, Inc. All rights reserved.
>>> + * Author: Jian Hu <jian.hu@amlogic.com>
>>> + */
>>> +
>>> +#include <linux/platform_device.h>
>>> +#include "clk-pll.h"
>>> +#include "clk-dualdiv.h"
>>> +#include "meson-eeclk.h"
>>> +#include "a1.h"
>>
>> Same as above
> OK, I will change the order.
> In fact, the clk-pll.h is not used in the current driver.
> I will remove it.
>>
>>> +
>>> +/* PLLs clock in gates, its parent is xtal */
>>> +static struct clk_regmap a1_xtal_clktree = {
>>> +	.data = &(struct clk_regmap_gate_data){
>>> +		.offset = SYS_OSCIN_CTRL,
>>> +		.bit_idx = 0,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data) {
>>> +		.name = "xtal_clktree",
>>> +		.ops = &clk_regmap_gate_ro_ops,
>>> +		.parent_data = &(const struct clk_parent_data) {
>>> +			.fw_name = "xtal",
>>> +		},
>>> +		.num_parents = 1,
>>> +		/*
>>> +		 * switch for xtal clock
>>> +		 * Linux should not change it at runtime
>>> +		 */
>>
>> Comment not useful: it uses the Ro ops
>>
> OK,  remove the comments
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_xtal_fixpll = {
>>> +	.data = &(struct clk_regmap_gate_data){
>>> +		.offset = SYS_OSCIN_CTRL,
>>> +		.bit_idx = 1,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data) {
>>> +		.name = "xtal_fixpll",
>>> +		.ops = &clk_regmap_gate_ops,
>>> +		.parent_data = &(const struct clk_parent_data) {
>>> +			.fw_name = "xtal",
>>> +		},
>>> +		.num_parents = 1,
>>> +		.flags = CLK_IS_CRITICAL,
>>> +		/*
>>> +		 * it feeds DDR,AXI,APB bus
>>> +		 * Linux should not change it at runtime
>>> +		 */
>>
>> Again, the child are critical, not directly this clock from your
>> comment.
>>
>> Remove CRITICAL, put RO is linux is not supposed to touch it.
>>
> repace as clk_regmap_gate_ro_ops
>>> +	},
>>> +};
>>> +
>
> [ ... ]
>
>>> +
>>> +/* dsp a clk */
>>> +static u32 mux_table_dsp_ab[] = { 0, 1, 2, 3, 4, 7 };
>>> +static const struct clk_parent_data dsp_ab_clk_parent_data[] = {
>>> +	{ .fw_name = "xtal", },
>>> +	{ .fw_name = "fclk_div2", },
>>> +	{ .fw_name = "fclk_div3", },
>>> +	{ .fw_name = "fclk_div5", },
>>> +	{ .fw_name = "hifi_pll", },
>>> +	{ .hw = &a1_rtc_clk.hw },
>>> +};
>>> +
>>> +static struct clk_regmap a1_dspa_a_sel = {
>>> +	.data = &(struct clk_regmap_mux_data){
>>> +		.offset = DSPA_CLK_CTRL0,
>>> +		.mask = 0x7,
>>> +		.shift = 10,
>>> +		.table = mux_table_dsp_ab,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "dspa_a_sel",
>>> +		.ops = &clk_regmap_mux_ops,
>>> +		.parent_data = dsp_ab_clk_parent_data,
>>> +		.num_parents = ARRAY_SIZE(dsp_ab_clk_parent_data),
>>
>> .flags = CLK_SET_RATE_PARENT ?
> Yes, I miss the flag.
>>
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_dspa_a_div = {
>>> +	.data = &(struct clk_regmap_div_data){
>>> +		.offset = DSPA_CLK_CTRL0,
>>> +		.shift = 0,
>>> +		.width = 10,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "dspa_a_div",
>>> +		.ops = &clk_regmap_divider_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_dspa_a_sel.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +		.flags = CLK_SET_RATE_PARENT,
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_dspa_a = {
>>> +	.data = &(struct clk_regmap_gate_data){
>>> +		.offset = DSPA_CLK_CTRL0,
>>> +		.bit_idx = 13,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data) {
>>> +		.name = "dspa_a",
>>> +		.ops = &clk_regmap_gate_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_dspa_a_div.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +		.flags = CLK_SET_RATE_PARENT,
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_dspa_b_sel = {
>>> +	.data = &(struct clk_regmap_mux_data){
>>> +		.offset = DSPA_CLK_CTRL0,
>>> +		.mask = 0x7,
>>> +		.shift = 26,
>>> +		.table = mux_table_dsp_ab,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "dspa_b_sel",
>>> +		.ops = &clk_regmap_mux_ops,
>>> +		.parent_data = dsp_ab_clk_parent_data,
>>> +		.num_parents = ARRAY_SIZE(dsp_ab_clk_parent_data),
>>
>> .flags = CLK_SET_RATE_PARENT ?
>>
> Yes, I will add it.
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_dspa_b_div = {
>>> +	.data = &(struct clk_regmap_div_data){
>>> +		.offset = DSPA_CLK_CTRL0,
>>> +		.shift = 16,
>>> +		.width = 10,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "dspa_b_div",
>>> +		.ops = &clk_regmap_divider_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_dspa_b_sel.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +		.flags = CLK_SET_RATE_PARENT,
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_dspa_b = {
>>> +	.data = &(struct clk_regmap_gate_data){
>>> +		.offset = DSPA_CLK_CTRL0,
>>> +		.bit_idx = 29,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data) {
>>> +		.name = "dspa_b",
>>> +		.ops = &clk_regmap_gate_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_dspa_b_div.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +		.flags = CLK_SET_RATE_PARENT,
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_dspa_sel = {
>>> +	.data = &(struct clk_regmap_mux_data){
>>> +		.offset = DSPA_CLK_CTRL0,
>>> +		.mask = 0x1,
>>> +		.shift = 15,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "dspa_sel",
>>> +		.ops = &clk_regmap_mux_ops,
>>> +		.parent_data = (const struct clk_parent_data []) {
>>> +			{ .hw = &a1_dspa_a.hw },
>>> +			{ .hw = &a1_dspa_b.hw },
>>> +		},
>>> +		.num_parents = 2,
>>> +		.flags = CLK_SET_RATE_PARENT,
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_dspa_en_dspa = {
>>> +	.data = &(struct clk_regmap_gate_data){
>>> +		.offset = DSPA_CLK_EN,
>>> +		.bit_idx = 1,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data) {
>>> +		.name = "dspa_en_dspa",
>>> +		.ops = &clk_regmap_gate_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_dspa_sel.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +		.flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>>
>> Why do you need CLK_IGNORE_UNUSED ?
>>
> I should remove it
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_dspa_en_nic = {
>>> +	.data = &(struct clk_regmap_gate_data){
>>> +		.offset = DSPA_CLK_EN,
>>> +		.bit_idx = 0,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data) {
>>> +		.name = "dspa_en_nic",
>>> +		.ops = &clk_regmap_gate_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_dspa_sel.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +		.flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>>
>> Why do you need CLK_IGNORE_UNUSED ?
>>
> I should remove it
>>> +	},
>>> +};
>>> +
>>
>> Same question and remarks applies to DSP B
>>
> got it
>>> +/* dsp b clk */
>>> +static struct clk_regmap a1_dspb_a_sel = {
>>> +	.data = &(struct clk_regmap_mux_data){
>>> +		.offset = DSPB_CLK_CTRL0,
>>> +		.mask = 0x7,
>>> +		.shift = 10,
>>> +		.table = mux_table_dsp_ab,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "dspb_a_sel",
>>> +		.ops = &clk_regmap_mux_ops,
>>> +		.parent_data = dsp_ab_clk_parent_data,
>>> +		.num_parents = ARRAY_SIZE(dsp_ab_clk_parent_data),
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_dspb_a_div = {
>>> +	.data = &(struct clk_regmap_div_data){
>>> +		.offset = DSPB_CLK_CTRL0,
>>> +		.shift = 0,
>>> +		.width = 10,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "dspb_a_div",
>>> +		.ops = &clk_regmap_divider_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_dspb_a_sel.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +		.flags = CLK_SET_RATE_PARENT,
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_dspb_a = {
>>> +	.data = &(struct clk_regmap_gate_data){
>>> +		.offset = DSPB_CLK_CTRL0,
>>> +		.bit_idx = 13,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data) {
>>> +		.name = "dspb_a",
>>> +		.ops = &clk_regmap_gate_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_dspb_a_div.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +		.flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_dspb_b_sel = {
>>> +	.data = &(struct clk_regmap_mux_data){
>>> +		.offset = DSPB_CLK_CTRL0,
>>> +		.mask = 0x7,
>>> +		.shift = 26,
>>> +		.table = mux_table_dsp_ab,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "dspb_b_sel",
>>> +		.ops = &clk_regmap_mux_ops,
>>> +		.parent_data = dsp_ab_clk_parent_data,
>>> +		.num_parents = ARRAY_SIZE(dsp_ab_clk_parent_data),
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_dspb_b_div = {
>>> +	.data = &(struct clk_regmap_div_data){
>>> +		.offset = DSPB_CLK_CTRL0,
>>> +		.shift = 16,
>>> +		.width = 10,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "dspb_b_div",
>>> +		.ops = &clk_regmap_divider_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_dspb_b_sel.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +		.flags = CLK_SET_RATE_PARENT,
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_dspb_b = {
>>> +	.data = &(struct clk_regmap_gate_data){
>>> +		.offset = DSPB_CLK_CTRL0,
>>> +		.bit_idx = 29,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data) {
>>> +		.name = "dspb_b",
>>> +		.ops = &clk_regmap_gate_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_dspb_b_div.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +		.flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_dspb_sel = {
>>> +	.data = &(struct clk_regmap_mux_data){
>>> +		.offset = DSPB_CLK_CTRL0,
>>> +		.mask = 0x1,
>>> +		.shift = 15,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "dspb_sel",
>>> +		.ops = &clk_regmap_mux_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_dspb_a.hw, &a1_dspb_b.hw,
>>> +		},
>>> +		.num_parents = 2,
>>> +		.flags = CLK_SET_RATE_PARENT,
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_dspb_en_dspb = {
>>> +	.data = &(struct clk_regmap_gate_data){
>>> +		.offset = DSPB_CLK_EN,
>>> +		.bit_idx = 1,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data) {
>>> +		.name = "dspb_en_dspb",
>>> +		.ops = &clk_regmap_gate_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_dspb_sel.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +		.flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_dspb_en_nic = {
>>> +	.data = &(struct clk_regmap_gate_data){
>>> +		.offset = DSPB_CLK_EN,
>>> +		.bit_idx = 0,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data) {
>>> +		.name = "dspb_en_nic",
>>> +		.ops = &clk_regmap_gate_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_dspb_sel.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +		.flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>>> +	},
>>> +};
>>> +
>>> +/* 12M/24M clock */
>>> +static struct clk_regmap a1_24m = {
>>> +	.data = &(struct clk_regmap_gate_data){
>>> +		.offset = CLK12_24_CTRL,
>>> +		.bit_idx = 11,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data) {
>>> +		.name = "24m",
>>> +		.ops = &clk_regmap_gate_ops,
>>> +		.parent_data = &(const struct clk_parent_data) {
>>> +			.fw_name = "xtal",
>>> +		},
>>> +		.num_parents = 1,
>>> +	},
>>> +};
>>> +
>
> [ ... ]
>
>>> +static struct clk_regmap a1_saradc_sel = {
>>> +	.data = &(struct clk_regmap_mux_data){
>>> +		.offset = SAR_ADC_CLK_CTRL,
>>> +		.mask = 0x1,
>>> +		.shift = 9,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "saradc_sel",
>>> +		.ops = &clk_regmap_mux_ops,
>>> +		.parent_data = (const struct clk_parent_data []) {
>>> +			{ .fw_name = "xtal", },
>>> +			{ .hw = &a1_sys_clk.hw, },
>>> +		},
>>> +		.num_parents = 2,
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_saradc_div = {
>>> +	.data = &(struct clk_regmap_div_data){
>>> +		.offset = SAR_ADC_CLK_CTRL,
>>> +		.shift = 0,
>>> +		.width = 8,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "saradc_div",
>>> +		.ops = &clk_regmap_divider_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_saradc_sel.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +		.flags = CLK_SET_RATE_PARENT,
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_saradc_clk = {
>>> +	.data = &(struct clk_regmap_gate_data){
>>> +		.offset = SAR_ADC_CLK_CTRL,
>>> +		.bit_idx = 8,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data) {
>>> +		.name = "saradc_clk",
>>> +		.ops = &clk_regmap_gate_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_saradc_div.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +		.flags = CLK_SET_RATE_PARENT,
>>> +	},
>>> +};
>>> +
>>> +/* pwm a/b/c/d parent data */
>>> +static const struct clk_parent_data pwm_parent_data[] = {
>>> +	{ .fw_name = "xtal", },
>>> +	{ .hw = &a1_sys_clk.hw },
>>> +};
>>
>> Looks like the same as SAR ADC
>>
> OK, I will describe it like SAR ADC for pwm a/b/c/d
>>> +
>>> +/* pwm a clk */
>>> +static struct clk_regmap a1_pwm_a_sel = {
>>> +	.data = &(struct clk_regmap_mux_data){
>>> +		.offset = PWM_CLK_AB_CTRL,
>>> +		.mask = 0x1,
>>> +		.shift = 9,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "pwm_a_sel",
>>> +		.ops = &clk_regmap_mux_ops,
>>> +		.parent_data = pwm_parent_data,
>>> +		.num_parents = ARRAY_SIZE(pwm_parent_data),
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_pwm_a_div = {
>>> +	.data = &(struct clk_regmap_div_data){
>>> +		.offset = PWM_CLK_AB_CTRL,
>>> +		.shift = 0,
>>> +		.width = 8,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "pwm_a_div",
>>> +		.ops = &clk_regmap_divider_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_pwm_a_sel.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +		.flags = CLK_SET_RATE_PARENT,
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_pwm_a = {
>>> +	.data = &(struct clk_regmap_gate_data){
>>> +		.offset = PWM_CLK_AB_CTRL,
>>> +		.bit_idx = 8,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data) {
>>> +		.name = "pwm_a",
>>> +		.ops = &clk_regmap_gate_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_pwm_a_div.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +		/*
>>> +		 * The CPU working voltage is controlled by pwm_a
>>> +		 * in BL2 firmware. add the CLK_IGNORE_UNUSED flag
>>> +		 * to avoid changing at runtime.
>>                                      ^ it
>>
>>> +		 * and is required by the platform to operate correctly.
>>                     "blabla. And" is strange
>>
>>> +		 * Until the following condition are met, we need this clock to
>>> +		 * be marked as critical:
>>> +		 * a) Mark the clock used by a firmware resource, if possible
>>> +		 * b) CCF has a clock hand-off mechanism to make the sure the
>>> +		 *    clock stays on until the proper driver comes along
>>> +		 */
>>> +		.flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>>
>> This only skips the late_init() disable of unused clocks
>>
>> Be aware that this is not fool-proof. If at any time a driver enable
>> then disable the clock, the clock will be disable and I guess your
>> platform will die if this provides the CPU voltage.
> OK, CLK_IS_CRITICAL is better.
>>
>>> +	},
>>> +};
>>> +
>>> +/* pwm b clk */
>>> +static struct clk_regmap a1_pwm_b_sel = {
>>> +	.data = &(struct clk_regmap_mux_data){
>>> +		.offset = PWM_CLK_AB_CTRL,
>>> +		.mask = 0x1,
>>> +		.shift = 25,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "pwm_b_sel",
>>> +		.ops = &clk_regmap_mux_ops,
>>> +		.parent_data = pwm_parent_data,
>>> +		.num_parents = ARRAY_SIZE(pwm_parent_data),
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_pwm_b_div = {
>>> +	.data = &(struct clk_regmap_div_data){
>>> +		.offset = PWM_CLK_AB_CTRL,
>>> +		.shift = 16,
>>> +		.width = 8,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "pwm_b_div",
>>> +		.ops = &clk_regmap_divider_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_pwm_b_sel.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +		.flags = CLK_SET_RATE_PARENT,
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_pwm_b = {
>>> +	.data = &(struct clk_regmap_gate_data){
>>> +		.offset = PWM_CLK_AB_CTRL,
>>> +		.bit_idx = 24,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data) {
>>> +		.name = "pwm_b",
>>> +		.ops = &clk_regmap_gate_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_pwm_b_div.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +		.flags = CLK_SET_RATE_PARENT,
>>> +	},
>>> +};
>>> +
>>> +/* pwm c clk */
>>> +static struct clk_regmap a1_pwm_c_sel = {
>>> +	.data = &(struct clk_regmap_mux_data){
>>> +		.offset = PWM_CLK_CD_CTRL,
>>> +		.mask = 0x1,
>>> +		.shift = 9,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "pwm_c_sel",
>>> +		.ops = &clk_regmap_mux_ops,
>>> +		.parent_data = pwm_parent_data,
>>> +		.num_parents = ARRAY_SIZE(pwm_parent_data),
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_pwm_c_div = {
>>> +	.data = &(struct clk_regmap_div_data){
>>> +		.offset = PWM_CLK_CD_CTRL,
>>> +		.shift = 0,
>>> +		.width = 8,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "pwm_c_div",
>>> +		.ops = &clk_regmap_divider_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_pwm_c_sel.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +		.flags = CLK_SET_RATE_PARENT,
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_pwm_c = {
>>> +	.data = &(struct clk_regmap_gate_data){
>>> +		.offset = PWM_CLK_CD_CTRL,
>>> +		.bit_idx = 8,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data) {
>>> +		.name = "pwm_c",
>>> +		.ops = &clk_regmap_gate_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_pwm_c_div.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +		.flags = CLK_SET_RATE_PARENT,
>>> +	},
>>> +};
>>> +
>>> +/* pwm d clk */
>>> +static struct clk_regmap a1_pwm_d_sel = {
>>> +	.data = &(struct clk_regmap_mux_data){
>>> +		.offset = PWM_CLK_CD_CTRL,
>>> +		.mask = 0x1,
>>> +		.shift = 25,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "pwm_d_sel",
>>> +		.ops = &clk_regmap_mux_ops,
>>> +		.parent_data = pwm_parent_data,
>>> +		.num_parents = ARRAY_SIZE(pwm_parent_data),
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_pwm_d_div = {
>>> +	.data = &(struct clk_regmap_div_data){
>>> +		.offset = PWM_CLK_CD_CTRL,
>>> +		.shift = 16,
>>> +		.width = 8,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "pwm_d_div",
>>> +		.ops = &clk_regmap_divider_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_pwm_d_sel.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +		.flags = CLK_SET_RATE_PARENT,
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_pwm_d = {
>>> +	.data = &(struct clk_regmap_gate_data){
>>> +		.offset = PWM_CLK_CD_CTRL,
>>> +		.bit_idx = 24,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data) {
>>> +		.name = "pwm_d",
>>> +		.ops = &clk_regmap_gate_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_pwm_d_div.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +		.flags = CLK_SET_RATE_PARENT,
>>> +	},
>>> +};
>>> +
>>> +static const struct clk_parent_data pwm_ef_parent_data[] = {
>>> +	{ .fw_name = "xtal", },
>>> +	{ .hw = &a1_sys_clk.hw },
>>> +	{ .fw_name = "fclk_div5", },
>>> +	{ .hw = &a1_rtc_clk.hw },
>>> +};
>>> +
>>> +/* pwm e clk */
>>> +static struct clk_regmap a1_pwm_e_sel = {
>>> +	.data = &(struct clk_regmap_mux_data){
>>> +		.offset = PWM_CLK_EF_CTRL,
>>> +		.mask = 0x3,
>>> +		.shift = 9,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "pwm_e_sel",
>>> +		.ops = &clk_regmap_mux_ops,
>>> +		.parent_data = pwm_ef_parent_data,
>>> +		.num_parents = ARRAY_SIZE(pwm_ef_parent_data),
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_pwm_e_div = {
>>> +	.data = &(struct clk_regmap_div_data){
>>> +		.offset = PWM_CLK_EF_CTRL,
>>> +		.shift = 0,
>>> +		.width = 8,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "pwm_e_div",
>>> +		.ops = &clk_regmap_divider_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_pwm_e_sel.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +		.flags = CLK_SET_RATE_PARENT,
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_pwm_e = {
>>> +	.data = &(struct clk_regmap_gate_data){
>>> +		.offset = PWM_CLK_EF_CTRL,
>>> +		.bit_idx = 8,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data) {
>>> +		.name = "pwm_e",
>>> +		.ops = &clk_regmap_gate_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_pwm_e_div.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +		.flags = CLK_SET_RATE_PARENT,
>>> +	},
>>> +};
>>> +
>>> +/* pwm f clk */
>>> +static struct clk_regmap a1_pwm_f_sel = {
>>> +	.data = &(struct clk_regmap_mux_data){
>>> +		.offset = PWM_CLK_EF_CTRL,
>>> +		.mask = 0x3,
>>> +		.shift = 25,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "pwm_f_sel",
>>> +		.ops = &clk_regmap_mux_ops,
>>> +		.parent_data = pwm_ef_parent_data,
>>> +		.num_parents = ARRAY_SIZE(pwm_ef_parent_data),
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_pwm_f_div = {
>>> +	.data = &(struct clk_regmap_div_data){
>>> +		.offset = PWM_CLK_EF_CTRL,
>>> +		.shift = 16,
>>> +		.width = 8,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "pwm_f_div",
>>> +		.ops = &clk_regmap_divider_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_pwm_f_sel.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +		.flags = CLK_SET_RATE_PARENT,
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_pwm_f = {
>>> +	.data = &(struct clk_regmap_gate_data){
>>> +		.offset = PWM_CLK_EF_CTRL,
>>> +		.bit_idx = 24,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data) {
>>> +		.name = "pwm_f",
>>> +		.ops = &clk_regmap_gate_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_pwm_f_div.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +		.flags = CLK_SET_RATE_PARENT,
>>> +	},
>>> +};
>>> +
>
> [ ... ]
>
>>> +
>>> +/* dmc clk */
>>> +static struct clk_regmap a1_dmc_sel = {
>>> +	.data = &(struct clk_regmap_mux_data){
>>> +		.offset = DMC_CLK_CTRL,
>>> +		.mask = 0x3,
>>> +		.shift = 9,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "dmc_sel",
>>> +		.ops = &clk_regmap_mux_ops,
>>> +		.parent_data = sd_emmc_parents,
>>> +		.num_parents = 4,
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_dmc_div = {
>>> +	.data = &(struct clk_regmap_div_data){
>>> +		.offset = DMC_CLK_CTRL,
>>> +		.shift = 0,
>>> +		.width = 8,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "dmc_div",
>>> +		.ops = &clk_regmap_divider_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_dmc_sel.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +		.flags = CLK_SET_RATE_PARENT,
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_dmc_sel2 = {
>>> +	.data = &(struct clk_regmap_mux_data){
>>> +		.offset = DMC_CLK_CTRL,
>>> +		.mask = 0x1,
>>> +		.shift = 15,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data){
>>> +		.name = "dmc_sel2",
>>> +		.ops = &clk_regmap_mux_ops,
>>> +		.parent_data = (const struct clk_parent_data []) {
>>> +			{ .hw = &a1_dmc_div.hw },
>>> +			{ .fw_name = "xtal", },
>>> +		},
>>> +		.num_parents = 2,
>>> +		.flags = CLK_SET_RATE_PARENT,
>>> +	},
>>> +};
>>> +
>>> +static struct clk_regmap a1_dmc = {
>>> +	.data = &(struct clk_regmap_gate_data){
>>> +		.offset = DMC_CLK_CTRL,
>>> +		.bit_idx = 8,
>>> +	},
>>> +	.hw.init = &(struct clk_init_data) {
>>> +		.name = "dmc",
>>> +		.ops = &clk_regmap_gate_ops,
>>> +		.parent_hws = (const struct clk_hw *[]) {
>>> +			&a1_dmc_sel2.hw
>>> +		},
>>> +		.num_parents = 1,
>>> +		/*
>>> +		 * This clock is used by DDR clock which setted in BL2
>>> +		 * and is required by the platform to operate correctly.
>>> +		 * Until the following condition are met, we need this clock to
>>> +		 * be marked as critical:
>>> +		 * a) Mark the clock used by a firmware resource, if possible
>>> +		 * b) CCF has a clock hand-off mechanism to make the sure the
>>> +		 *    clock stays on until the proper driver comes along
>>> +		 */
>>> +		.flags = CLK_SET_RATE_PARENT | CLK_IS_CRITICAL,
>>> +	},
>>> +};
>>
>> Should you put all this DMC stuff in RO until you got a driver for it ?
> OK, replace as clk_regmap_gate_ro_ops
>>
> [ ... ]
>>> +
>>> +static int meson_a1_periphs_probe(struct platform_device *pdev)
>>> +{
>>> +	int ret;
>>> +
>>> +	ret = meson_eeclkc_probe(pdev);
>>> +	if (ret)
>>> +		return ret;
>>> +
>>> +	return 0;
>>> +}
>>
>> Again this function is function is useless and it makes me wonder if you
>> should really be using meson_eeclkc_probe()
>>
>> This makes you use syscon which is not correct unless you have a good
>> reason ?
>>
> If it can not use the meson_eeclkc_probe(), I will realize a probe function
> which is mostly duplicate with meson_eeclkc_probe() except
> "syscon_node_to_regmap"
>
> Maybe another common probe function and a new file are required for A1
> three drivers? （include the CPU clock driver）

Maybe

>
> Or using meson_eeclkc_probe is more easier?

It is not question of easiness, but correctness.

>
>> Is there anything but clocks and resets in these register region ?
> No, there is only clocks in the register region.
> the same does the PLL register region.

Then there is no reason to use syscon for those drivers

>>
>>> +
>>> +static const struct meson_eeclkc_data a1_periphs_data = {
>>> +		.regmap_clks = a1_periphs_regmaps,
>>> +		.regmap_clk_num = ARRAY_SIZE(a1_periphs_regmaps),
>>> +		.hw_onecell_data = &a1_periphs_hw_onecell_data,
>>> +};
>>> +static const struct of_device_id clkc_match_table[] = {
>>> +	{
>>> +		.compatible = "amlogic,a1-periphs-clkc",
>>> +		.data = &a1_periphs_data
>>> +	},
>>> +	{ /* sentinel */ }
>>> +};
>>> +
>>> +static struct platform_driver a1_driver = {
>>> +	.probe		= meson_a1_periphs_probe,
>>> +	.driver		= {
>>> +		.name	= "a1-periphs-clkc",
>>> +		.of_match_table = clkc_match_table,
>>> +	},
>>> +};
>>> +
>>> +builtin_platform_driver(a1_driver);
>>> diff --git a/drivers/clk/meson/a1.h b/drivers/clk/meson/a1.h
>>> new file mode 100644
>>> index 0000000..1ae5e04
>>> --- /dev/null
>>> +++ b/drivers/clk/meson/a1.h
>>> @@ -0,0 +1,120 @@
>>> +/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
>>> +/*
>>> + * Copyright (c) 2019 Amlogic, Inc. All rights reserved.
>>> + */
>>> +
>>> +#ifndef __A1_H
>>> +#define __A1_H
>>> +
>>> +/* peripheral clock controller register offset */
>>> +#define SYS_OSCIN_CTRL			0x0
>>> +#define RTC_BY_OSCIN_CTRL0		0x4
>>> +#define RTC_BY_OSCIN_CTRL1		0x8
>>> +#define RTC_CTRL			0xc
>>> +#define SYS_CLK_CTRL0			0x10
>>> +#define AXI_CLK_CTRL0			0x14
>>> +#define SYS_CLK_EN0			0x1c
>>> +#define SYS_CLK_EN1			0x20
>>> +#define AXI_CLK_EN			0x24
>>> +#define DSPA_CLK_EN			0x28
>>> +#define DSPB_CLK_EN			0x2c
>>> +#define DSPA_CLK_CTRL0			0x30
>>> +#define DSPB_CLK_CTRL0			0x34
>>> +#define CLK12_24_CTRL			0x38
>>> +#define GEN_CLK_CTRL			0x3c
>>> +#define TIMESTAMP_CTRL0			0x40
>>> +#define TIMESTAMP_CTRL1			0x44
>>> +#define TIMESTAMP_CTRL2			0x48
>>> +#define TIMESTAMP_VAL0			0x4c
>>> +#define TIMESTAMP_VAL1			0x50
>>> +#define TIMEBASE_CTRL0			0x54
>>> +#define TIMEBASE_CTRL1			0x58
>>> +#define SAR_ADC_CLK_CTRL		0xc0
>>> +#define PWM_CLK_AB_CTRL			0xc4
>>> +#define PWM_CLK_CD_CTRL			0xc8
>>> +#define PWM_CLK_EF_CTRL			0xcc
>>> +#define SPICC_CLK_CTRL			0xd0
>>> +#define TS_CLK_CTRL			0xd4
>>> +#define SPIFC_CLK_CTRL			0xd8
>>> +#define USB_BUSCLK_CTRL			0xdc
>>> +#define SD_EMMC_CLK_CTRL		0xe0
>>> +#define CECA_CLK_CTRL0			0xe4
>>> +#define CECA_CLK_CTRL1			0xe8
>>> +#define CECB_CLK_CTRL0			0xec
>>> +#define CECB_CLK_CTRL1			0xf0
>>> +#define PSRAM_CLK_CTRL			0xf4
>>> +#define DMC_CLK_CTRL			0xf8
>>> +#define FCLK_DIV1_SEL			0xfc
>>> +#define TST_CTRL			0x100
>>> +
>>> +#define CLKID_XTAL_CLKTREE		0
>>> +#define CLKID_SYS_A_SEL			89
>>> +#define CLKID_SYS_A_DIV			90
>>> +#define CLKID_SYS_A			91
>>> +#define CLKID_SYS_B_SEL			92
>>> +#define CLKID_SYS_B_DIV			93
>>> +#define CLKID_SYS_B			94
>>> +#define CLKID_DSPA_A_SEL		95
>>> +#define CLKID_DSPA_A_DIV		96
>>> +#define CLKID_DSPA_A			97
>>> +#define CLKID_DSPA_B_SEL		98
>>> +#define CLKID_DSPA_B_DIV		99
>>> +#define CLKID_DSPA_B			100
>>> +#define CLKID_DSPB_A_SEL		101
>>> +#define CLKID_DSPB_A_DIV		102
>>> +#define CLKID_DSPB_A			103
>>> +#define CLKID_DSPB_B_SEL		104
>>> +#define CLKID_DSPB_B_DIV		105
>>> +#define CLKID_DSPB_B			106
>>> +#define CLKID_RTC_32K_CLKIN		107
>>> +#define CLKID_RTC_32K_DIV		108
>>> +#define CLKID_RTC_32K_XTAL		109
>>> +#define CLKID_RTC_32K_SEL		110
>>> +#define CLKID_CECB_32K_CLKIN		111
>>> +#define CLKID_CECB_32K_DIV		112
>>> +#define CLKID_CECB_32K_SEL_PRE		113
>>> +#define CLKID_CECB_32K_SEL		114
>>> +#define CLKID_CECA_32K_CLKIN		115
>>> +#define CLKID_CECA_32K_DIV		116
>>> +#define CLKID_CECA_32K_SEL_PRE		117
>>> +#define CLKID_CECA_32K_SEL		118
>>> +#define CLKID_DIV2_PRE			119
>>> +#define CLKID_24M_DIV2			120
>>> +#define CLKID_GEN_SEL			121
>>> +#define CLKID_GEN_DIV			122
>>> +#define CLKID_SARADC_DIV		123
>>> +#define CLKID_PWM_A_SEL			124
>>> +#define CLKID_PWM_A_DIV			125
>>> +#define CLKID_PWM_B_SEL			126
>>> +#define CLKID_PWM_B_DIV			127
>>> +#define CLKID_PWM_C_SEL			128
>>> +#define CLKID_PWM_C_DIV			129
>>> +#define CLKID_PWM_D_SEL			130
>>> +#define CLKID_PWM_D_DIV			131
>>> +#define CLKID_PWM_E_SEL			132
>>> +#define CLKID_PWM_E_DIV			133
>>> +#define CLKID_PWM_F_SEL			134
>>> +#define CLKID_PWM_F_DIV			135
>>> +#define CLKID_SPICC_SEL			136
>>> +#define CLKID_SPICC_DIV			137
>>> +#define CLKID_SPICC_SEL2		138
>>> +#define CLKID_TS_DIV			139
>>> +#define CLKID_SPIFC_SEL			140
>>> +#define CLKID_SPIFC_DIV			141
>>> +#define CLKID_SPIFC_SEL2		142
>>> +#define CLKID_USB_BUS_SEL		143
>>> +#define CLKID_USB_BUS_DIV		144
>>> +#define CLKID_SD_EMMC_SEL		145
>>> +#define CLKID_SD_EMMC_DIV		146
>>> +#define CLKID_SD_EMMC_SEL2		147
>>> +#define CLKID_PSRAM_SEL			148
>>> +#define CLKID_PSRAM_DIV			149
>>> +#define CLKID_PSRAM_SEL2		150
>>> +#define CLKID_DMC_SEL			151
>>> +#define CLKID_DMC_DIV			152
>>> +#define CLKID_DMC_SEL2			153
>>> +#define NR_CLKS				154
>>> +
>>> +#include <dt-bindings/clock/a1-clkc.h>
>>> +
>>> +#endif /* __A1_H */
>>
>> .
>>


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel