From mboxrd@z Thu Jan  1 00:00:00 1970
From: lorenzo.pieralisi@arm.com (Lorenzo Pieralisi)
Date: Tue, 7 Oct 2014 15:47:50 +0100
Subject: [RFC 2/4] PCI: generic: Add support for ARM64 and MSI(x)
In-Reply-To: <3659934.boXsmm8jcn@wuerfel>
References: <1411937610-22125-1-git-send-email-suravee.suthikulpanit@amd.com>
 <3256560.C0cZnIlnAv@wuerfel>
 <20141007120659.GA30590@e102568-lin.cambridge.arm.com>
 <3659934.boXsmm8jcn@wuerfel>
Message-ID: <20141007144750.GB30590@e102568-lin.cambridge.arm.com>
To: linux-arm-kernel@lists.infradead.org
List-Id: linux-arm-kernel.lists.infradead.org

On Tue, Oct 07, 2014 at 02:52:27PM +0100, Arnd Bergmann wrote:
> On Tuesday 07 October 2014 13:06:59 Lorenzo Pieralisi wrote:
> > On Wed, Oct 01, 2014 at 10:38:45AM +0100, Arnd Bergmann wrote:
> > 
> > [...]
> > 
> > > pci_mmap_page_range could either get generalized some more in an attempt
> > > to have a __weak default implementation that works on ARM, or it could
> > > be changed to lose the dependency on pci_sys_data instead. In either
> > > case, the change would involve using the generic pci_host_bridge_window
> > > list.
> > 
> > On ARM pci_mmap_page_range requires pci_sys_data to retrieve its
> > mem_offset parameter. I had a look, and I do not understand *why*
> > it is required in that function, so I am asking. That function
> > is basically used to map PCI resources to userspace, IIUC, through
> > /proc or /sysfs file mappings. As far as I understand those mappings
> > expect VMA pgoff to be the CPU address when files representing resources
> > are mmapped from /proc and 0 when mmapped from /sys (I mean from
> > userspace, then VMA pgoff should be updated by the kernel to map the
> > resource).
> 
> Applying the mem_offset is certainly the more intuitive way, since
> that lets you read the PCI BAR values from a device and access the
> device with the appropriate offsets.

Ok, but I am referring to this snippet (drivers/pci/pci-sysfs.c):

/* pci_mmap_page_range() expects the same kind of entry as coming
 * from /proc/bus/pci/ which is a "user visible" value. If this is
 * different from the resource itself, arch will do necessary fixup.
 */
pci_resource_to_user(pdev, i, res, &start, &end);

--> Here start represents a CPU physical address, if pci_resource_to_user()
    does not fix it up, correct ?

vma->vm_pgoff += start >> PAGE_SHIFT;

[...]

return pci_mmap_page_range(...);

pci_mmap_page_range() applies (mem_offset >> PAGE_SHIFT) to pgoff in the
ARM implemention.

Is not there a mismatch here on platforms where mem_offset != 0 ?

> > Question is: why pci_mmap_page_range() should apply an additional
> > shift to the VMA pgoff based on pci_sys_data.mem_offset, which represents
> > the offset from cpu->bus offset. I do not understand that. PowerPC
> > does not seem to apply that fix-up (in PowerPC __pci_mmap_make_offset there
> > is commented out code which prevents the pci_mem_offset shift to be
> > applied). I think it all boils down to what the userspace interface is
> > expecting when the memory areas are mmapped, if anyone has comments on
> > this that is appreciated.
> 
> The important part is certainly that whatever transformation is done
> by pci_resource_to_user() gets undone by __pci_mmap_make_offset().

Exactly, it does not seem to be the case above, that's why I asked.

> In case of PowerPC and Microblaze, the mem_offset handling is commented
> out in both, to work around X11 trying to use the same values on
> /dev/mem. However, they do have the respective fixup for io_offset.
> 
> sparc applies the offset in both places for both io_offset and mem_offset.
> xtensa applies only io_offset in __pci_mmap_make_offset but neither
>   in pci_resource_to_user. This probably works because the mem_offset is
>   always zero there.
> mips applies a different fixup (for 36-bit addressing), but not the
>   mem_offset.
> 
> Every other architecture applies no offset here, neither in __pci_mmap_make_offset/pci_mmap_page_range nor in pci_resource_to_user
> 
> The only hint I could find for how the ARM version came to be is
> from the historic kernel tree git log for linux-2.5.42, which added
> the current code as
> 
>     2002/10/13 11:05:47+01:00 rmk
>     [ARM] Update pcibios_enable_device, supply pci_mmap_page_range()
>     Update pcibios_enable_device to only enable requested resources,
>     mainly for IDE.  Supply a pci_mmap_page_range() function to allow
>     user space to mmap PCI regions.
> 
> At that point, only two platforms had a nonzero mem_offset:
> footbridge/dc21285 and integrator/pci_v3. Both were using VGA,
> and presumably used this to make X work. (rmk might remember
> details).

I think that, as I mentioned, it boils down to what the userspace
interface (proc/sys and they seem to differ) is supposed to be passed
from userspace processes upon mmap.

> The code at the time matched what powerpc and sparc did, but then
> both implemented pci_resource_to_user() in order for libpciaccess
> to work correctly (bcea1db16b for sparc, 463ce0e103f for powerpc),
> and later powerpc changed it again to not apply the offset in
> pci_resource_to_user or pci_mmap_page_range in 396a1a5832ae.

I will keep investigating, thank you for your help, any further comments
appreciated.

Lorenzo