From mboxrd@z Thu Jan 1 00:00:00 1970 From: shawn.guo@linaro.org (Shawn Guo) Date: Tue, 3 Mar 2015 09:05:32 +0800 Subject: [PATCH 2/2] ARM: dts: imx6: add support for technexion toucan board In-Reply-To: <1424457195-8796-2-git-send-email-m.grzeschik@pengutronix.de> References: <1424457195-8796-1-git-send-email-m.grzeschik@pengutronix.de> <1424457195-8796-2-git-send-email-m.grzeschik@pengutronix.de> Message-ID: <20150303010530.GA20455@dragon> To: linux-arm-kernel@lists.infradead.org List-Id: linux-arm-kernel.lists.infradead.org On Fri, Feb 20, 2015 at 07:33:15PM +0100, Michael Grzeschik wrote: > This patch adds the second user of the edm1 module. > > Signed-off-by: Michael Grzeschik > --- > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/imx6dl-toucan.dts | 203 ++++++++++++++++++++++++++++++++++++ > 2 files changed, 204 insertions(+) > create mode 100644 arch/arm/boot/dts/imx6dl-toucan.dts > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index 91bd5bd..bea96c8 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -234,6 +234,7 @@ dtb-$(CONFIG_ARCH_MXC) += \ > imx6dl-tx6dl-comtft.dtb \ > imx6dl-tx6u-801x.dtb \ > imx6dl-tx6u-811x.dtb \ > + imx6dl-toucan.dtb \ 'o' goes before 'x' in alphabet table. > imx6dl-wandboard.dtb \ > imx6dl-wandboard-revb1.dtb \ > imx6q-arm2.dtb \ > diff --git a/arch/arm/boot/dts/imx6dl-toucan.dts b/arch/arm/boot/dts/imx6dl-toucan.dts > new file mode 100644 > index 0000000..c801774 > --- /dev/null > +++ b/arch/arm/boot/dts/imx6dl-toucan.dts > @@ -0,0 +1,203 @@ > +/* > + * Copyright 2015 Michael Grzeschik , Pengutronix > + * > + * The code contained herein is licensed under the GNU General Public > + * License. You may obtain a copy of the GNU General Public License > + * Version 2 or later at the following locations: > + * > + * http://www.opensource.org/licenses/gpl-license.html > + * http://www.gnu.org/copyleft/gpl.html > + */ > +/dts-v1/; > + > +#include "imx6dl.dtsi" > +#include "imx6qdl-edm1.dtsi" > +#include > + > +/ { > + model = "Technexion Toucan"; > + compatible = "technexion,toucan", "fsl,imx6dl"; > + > + memory { > + reg = <0x10000000 0x40000000>; > + }; > + > + regulators { > + compatible = "simple-bus"; > + #address-cells = <1>; > + #size-cells = <0>; > + > + reg_usbotg_vbus: regulator at 0 { > + compatible = "regulator-fixed"; > + reg = <7>; 'reg' value should match @unit-address. > + regulator-name = "usbotg_vbus"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + pinctrl-names = "default"; > + gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + }; > + > + reg_2p5v: regulator at 1 { > + compatible = "regulator-fixed"; > + reg = <0>; > + regulator-name = "2P5V"; > + regulator-min-microvolt = <2500000>; > + regulator-max-microvolt = <2500000>; > + regulator-always-on; > + }; > + > + reg_3p3v: regulator at 2 { > + compatible = "regulator-fixed"; > + reg = <1>; > + regulator-name = "3P3V"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + }; > + > + sound { > + compatible = "fsl,imx6-toucan-sgtl5000", > + "fsl,imx-audio-sgtl5000"; > + model = "imx6-toucan-sgtl5000"; > + ssi-controller = <&ssi1>; > + audio-codec = <&codec>; > + audio-routing = > + "MIC_IN", "Mic Jack", > + "Mic Jack", "Mic Bias", > + "Headphone Jack", "HP_OUT"; > + mux-int-port = <1>; > + mux-ext-port = <3>; > + }; Can generic simple-audio-card be used instead? > +}; > + > +&iomuxc { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_hog>; > + > + imx6qdl-toucan { > + pinctrl_hog: hoggrp { > + fsl,pins = < > + MX6QDL_PAD_CSI0_DAT19__GPIO6_IO05 0x0b0b0 > + MX6QDL_PAD_CSI0_DAT16__GPIO6_IO02 0x0b0b0 > + MX6QDL_PAD_CSI0_DAT18__GPIO6_IO04 0x0b0b0 > + MX6QDL_PAD_EIM_D27__GPIO3_IO27 0x0b0b0 > + MX6QDL_PAD_EIM_D26__GPIO3_IO26 0x0b0b0 > + MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0x0b0b0 > + MX6QDL_PAD_CSI0_DAT17__GPIO6_IO03 0x0b0b0 > + MX6QDL_PAD_ENET_RX_ER__GPIO1_IO24 0x0b0b0 > + MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x0b0b0 > + MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x0b0b0 > + MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x17059 > + >; > + }; > + }; > +}; > + > +&fec { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_enet>; > + phy-mode = "rgmii"; > + phy-reset-gpios = <&gpio3 29 GPIO_ACTIVE_LOW>; > + interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>, > + <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>; > + status = "okay"; > +}; > + > +&audmux { Please sort these nodes alphabetically in label name. Shawn > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_audmux>; > + status = "okay"; > +}; > + > +&usbh1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usbh1>; > + dr_mode = "host"; > + disable-over-current; > + status = "okay"; > +}; > + > +&usbotg { > + vbus-supply = <®_usbotg_vbus>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usbotg>; > + dr_mode = "peripheral"; > + disable-over-current; > + status = "okay"; > +}; > + > +&can1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_flexcan1>; > + status = "okay"; > +}; > + > +&can2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_flexcan2>; > + status = "okay"; > +}; > + > +&ssi1 { > + status = "okay"; > +}; > + > +&hdmi { > + ddc-i2c-bus = <&i2c1>; > + status = "okay"; > +}; > + > +&i2c1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c1>; > + clock-frequency = <400000>; > + status = "okay"; > +}; > + > +&i2c2 { > + clock-frequency = <100000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c2>; > + status = "okay"; > + > + codec: sgtl5000 at 0a { > + compatible = "fsl,sgtl5000"; > + reg = <0x0a>; > + clocks = <&clks 201>; > + VDDA-supply = <®_2p5v>; > + VDDIO-supply = <®_3p3v>; > + }; > +}; > + > +&uart1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart1 &pinctrl_uart1_rtscts>; > + status = "okay"; > +}; > + > +&uart2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart2 &pinctrl_uart2_rtscts>; > + status = "okay"; > +}; > + > +&usdhc1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usdhc1>; > + bus-width = <4>; > + no-1-8-v; > + cd-gpios = <&gpio1 2 0>; > + fsl,wp-controller; > + status = "okay"; > +}; > + > +&usdhc3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usdhc3>; > + bus-width = <4>; > + no-1-8-v; > + fsl,wp-controller; > + status = "okay"; > +}; > -- > 2.1.4 >