[PATCH 2/2] memory: omap-gpmc: Add Kconfig option for debug

[tony@atomide.com (Tony Lindgren)]

* Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com> [160101 03:29]:
> Hi Tony,
> 
> On 21.05.2015 00:21, Tony Lindgren wrote:
> >We support decoding the bootloader values if DEBUG is defined.
> >But we also need to change the struct omap_hwmod flags to have
> >HWMOD_INIT_NO_RESET to avoid the GPMC being reset during the
> >boot. Otherwise just the default timings will be displayed
> >instead of the bootloader configured timings.
> >
> >This also allows us to clean up the various GPMC related
> >hwmod flags. For debugging, we only need HWMOD_INIT_NO_RESET,
> >and HWMOD_INIT_NO_IDLE is not needed.
> >
> >Cc: Brian Hutchinson <b.hutchman@gmail.com>
> >Cc: Paul Walmsley <paul@pwsan.com>
> >Cc: Roger Quadros <rogerq@ti.com>
> >Signed-off-by: Tony Lindgren <tony@atomide.com>
> >---
> >  arch/arm/mach-omap2/omap_hwmod.h                        |  6 ++++++
> >  arch/arm/mach-omap2/omap_hwmod_2xxx_ipblock_data.c      | 12 ++----------
> >  arch/arm/mach-omap2/omap_hwmod_33xx_43xx_ipblock_data.c |  3 ++-
> >  arch/arm/mach-omap2/omap_hwmod_3xxx_data.c              | 12 ++----------
> >  arch/arm/mach-omap2/omap_hwmod_44xx_data.c              | 11 ++---------
> >  arch/arm/mach-omap2/omap_hwmod_7xx_data.c               |  4 ++--
> >  arch/arm/mach-omap2/omap_hwmod_81xx_data.c              |  2 ++
> >  drivers/memory/Kconfig                                  |  8 ++++++++
> >  drivers/memory/omap-gpmc.c                              |  6 +++---
> >  9 files changed, 29 insertions(+), 35 deletions(-)
> >
> 
> 1. Happy new year :)

Same to you :)

> 2. It was a while I tested upstream on N900 but I had some spare time during
> the holidays to play, so I tried to boot 4.4-rc6 with Maemo 5. To my
> surprise, after that try, Maemo 5 rootfs, which is located on onenand became
> irreversibly corrupted. I bisected the tree to the $subject commit and after
> restoring HWMOD_INIT_NO_RESET in omap3xxx_gpmc_hwmod flags, the problem was
> solved. It seems that GPMC is either incorrectly or incompletely setup by
> the kernel, leading to failed onenand reads/writes and whatnot.
> Unfortunately, what I have here is a release device, so I am unable to
> capture any logs through the serial port. BTW keep in mind that rootfs
> corruption happens as soon as a boot is attempted, even after a freshly
> flashed rootfs.

Oh crap, sorry to hear that :(

Care to boot with CONFIG_OMAP_GPMC_DEBUG=y and post the gpmc related dmesg
output? The dmesg timings with CONFIG_OMAP_GPMC_DEBUG enabled should be
compared against omap3-n900.dts gpmc timings. And if you don't see the whole
dmesg after booting, you may need to also increase CONFIG_LOG_BUF_SHIFT.
Meanwhile, I'll try to also produce it here.

Chances are we have bad or incomplete timings in the n900 :(

Regards,

Tony