From mboxrd@z Thu Jan 1 00:00:00 1970 From: bhe@redhat.com (Baoquan He) Date: Fri, 1 Jul 2016 15:45:05 +0800 Subject: [PATCH v20 13/14] arm64: kdump: update a kernel doc In-Reply-To: <20160701073707.GM20774@linaro.org> References: <20160630090045.GA16958@x1.redhat.com> <20160701073707.GM20774@linaro.org> Message-ID: <20160701074505.GB10467@x1.redhat.com> To: linux-arm-kernel@lists.infradead.org List-Id: linux-arm-kernel.lists.infradead.org On 07/01/16 at 04:37pm, AKASHI Takahiro wrote: > Dave, Boaquan, > > Thank you for your reviewing. > > On Thu, Jun 30, 2016 at 05:00:45PM +0800, Baoquan He wrote: > > On 06/23/16 at 05:54pm, Geoff Levand wrote: > > > From: AKASHI Takahiro > > > > > > This patch adds arch specific descriptions about kdump usage on arm64 > > > to kdump.txt. > > > > > > Signed-off-by: AKASHI Takahiro > > > --- > > > Documentation/kdump/kdump.txt | 15 ++++++++++++++- > > > 1 file changed, 14 insertions(+), 1 deletion(-) > > > > > > diff --git a/Documentation/kdump/kdump.txt b/Documentation/kdump/kdump.txt > > > index 88ff63d..5d6da09 100644 > > > --- a/Documentation/kdump/kdump.txt > > > +++ b/Documentation/kdump/kdump.txt > > > @@ -18,7 +18,7 @@ memory image to a dump file on the local disk, or across the network to > > > a remote system. > > > > > > Kdump and kexec are currently supported on the x86, x86_64, ppc64, ia64, > > > -s390x and arm architectures. > > > +s390x, arm and arm64 architectures. > > > > > > When the system kernel boots, it reserves a small section of memory for > > > the dump-capture kernel. This ensures that ongoing Direct Memory Access > > > @@ -249,6 +249,12 @@ Dump-capture kernel config options (Arch Dependent, arm) > > > > > > AUTO_ZRELADDR=y > > > > > > +Dump-capture kernel config options (Arch Dependent, arm64) > > > +---------------------------------------------------------- > > > + > > > +1) Currently, kvm will not be enabled on the dump-capture kernel even > > > + if it is configured. And here, could you say more about it? > > > + > > > Extended crashkernel syntax > > > =========================== > > > > > > @@ -305,6 +311,8 @@ Boot into System Kernel > > > kernel will automatically locate the crash kernel image within the > > > first 512MB of RAM if X is not given. > > > > > > + On arm64, use "crashkernel=Y[@X]". Note that the start address of > > ~ Why square brackets here, is it > > different than other arch? > > I want to clearly indicate that "@X" is optional, and that, when you explicitly > specify it, X must be properly aligned. > I think that "[..]" notation is quite common. Yes, I see that. Just that has been noted in "Extended crashkernel syntax" section, and adding "[]" is not consistent with other places where "crashkernel=Y at X" is referred to in this section. Just feel it's a little redundent. Anyway it's not very critical, and Dave has acked it, I am fine if you want to keep it. Thanks Baoquan > > Thanks, > -Takahiro AKASHI > > > > > Except for this, it looks good to me. > > > > Thanks > > Baoquan > > > > > + the kernel, X if explicitly specified, must be aligned to 2MiB (0x200000). > > > > > > Load the Dump-capture Kernel > > > ============================ > > > @@ -327,6 +335,8 @@ For s390x: > > > - Use image or bzImage > > > For arm: > > > - Use zImage > > > +For arm64: > > > + - Use vmlinux or Image > > > > > > If you are using a uncompressed vmlinux image then use following command > > > to load dump-capture kernel. > > > @@ -370,6 +380,9 @@ For s390x: > > > For arm: > > > "1 maxcpus=1 reset_devices" > > > > > > +For arm64: > > > + "1 maxcpus=1 reset_devices" > > > + > > > Notes on loading the dump-capture kernel: > > > > > > * By default, the ELF headers are stored in ELF64 format to support > > > -- > > > 2.5.0 > > > > > > > > > > > > _______________________________________________ > > > kexec mailing list > > > kexec at lists.infradead.org > > > http://lists.infradead.org/mailman/listinfo/kexec