From: jon.mason@broadcom.com (Jon Mason)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH V2 2/2] thermal: broadcom: add Northstar thermal driver
Date: Fri, 24 Mar 2017 10:35:36 -0400 [thread overview]
Message-ID: <20170324143535.GA31953@broadcom.com> (raw)
In-Reply-To: <20170323223045.15786-2-zajec5@gmail.com>
On Thu, Mar 23, 2017 at 11:30:45PM +0100, Rafa? Mi?ecki wrote:
> From: Rafa? Mi?ecki <rafal@milecki.pl>
>
> Northstar is a SoC family commonly used in home routers. This commit
> adds a driver for checking CPU temperature. As Northstar Plus seems to
> also have this IP block this new symbol gets ARCH_BCM_IPROC dependency.
>
> Signed-off-by: Rafa? Mi?ecki <rafal@milecki.pl>
> Signed-off-by: Jon Mason <jon.mason@broadcom.com>
> ---
> V2: Make it iProc specific as NSP can also use this driver
> Select proper symbols in config ARCH_BCM_IPROC
> Define PVTMON register bits
> Update code selecting temperature monitor mode
> Thank you Jon!
> ---
> arch/arm/mach-bcm/Kconfig | 2 +
> drivers/thermal/Kconfig | 5 ++
> drivers/thermal/Makefile | 1 +
> drivers/thermal/broadcom/Kconfig | 7 +++
> drivers/thermal/broadcom/Makefile | 1 +
> drivers/thermal/broadcom/ns-thermal.c | 98 +++++++++++++++++++++++++++++++++++
> 6 files changed, 114 insertions(+)
> create mode 100644 drivers/thermal/broadcom/Kconfig
> create mode 100644 drivers/thermal/broadcom/Makefile
> create mode 100644 drivers/thermal/broadcom/ns-thermal.c
>
> diff --git a/arch/arm/mach-bcm/Kconfig b/arch/arm/mach-bcm/Kconfig
> index a0e66d8200c5..da2bfeb8e390 100644
> --- a/arch/arm/mach-bcm/Kconfig
> +++ b/arch/arm/mach-bcm/Kconfig
> @@ -19,6 +19,8 @@ config ARCH_BCM_IPROC
> select GPIOLIB
> select ARM_AMBA
> select PINCTRL
> + select THERMAL
> + select THERMAL_OF
> help
> This enables support for systems based on Broadcom IPROC architected SoCs.
> The IPROC complex contains one or more ARM CPUs along with common
> diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
> index 776b34396144..008e173ec825 100644
> --- a/drivers/thermal/Kconfig
> +++ b/drivers/thermal/Kconfig
> @@ -392,6 +392,11 @@ config MTK_THERMAL
> Enable this option if you want to have support for thermal management
> controller present in Mediatek SoCs
>
> +menu "Broadcom thermal drivers"
> +depends on ARCH_BCM || COMPILE_TEST
> +source "drivers/thermal/broadcom/Kconfig"
> +endmenu
> +
> menu "Texas Instruments thermal drivers"
> depends on ARCH_HAS_BANDGAP || COMPILE_TEST
> depends on HAS_IOMEM
> diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
> index 7adae2029355..549d81b6363c 100644
> --- a/drivers/thermal/Makefile
> +++ b/drivers/thermal/Makefile
> @@ -27,6 +27,7 @@ thermal_sys-$(CONFIG_CLOCK_THERMAL) += clock_cooling.o
> thermal_sys-$(CONFIG_DEVFREQ_THERMAL) += devfreq_cooling.o
>
> # platform thermal drivers
> +obj-y += broadcom/
> obj-$(CONFIG_QCOM_SPMI_TEMP_ALARM) += qcom-spmi-temp-alarm.o
> obj-$(CONFIG_SPEAR_THERMAL) += spear_thermal.o
> obj-$(CONFIG_ROCKCHIP_THERMAL) += rockchip_thermal.o
> diff --git a/drivers/thermal/broadcom/Kconfig b/drivers/thermal/broadcom/Kconfig
> new file mode 100644
> index 000000000000..39b92a1f3584
> --- /dev/null
> +++ b/drivers/thermal/broadcom/Kconfig
> @@ -0,0 +1,7 @@
> +config BCM_NS_THERMAL
> + tristate "Northstar thermal driver"
> + depends on ARCH_BCM_IPROC || COMPILE_TEST
> + help
> + Northstar's DMU (Device Management Unit) block contains a thermal
> + sensor that allows checking CPU temperature. This driver provides
> + support for it.
> diff --git a/drivers/thermal/broadcom/Makefile b/drivers/thermal/broadcom/Makefile
> new file mode 100644
> index 000000000000..059df9a0ed69
> --- /dev/null
> +++ b/drivers/thermal/broadcom/Makefile
> @@ -0,0 +1 @@
> +obj-$(CONFIG_BCM_NS_THERMAL) += ns-thermal.o
> diff --git a/drivers/thermal/broadcom/ns-thermal.c b/drivers/thermal/broadcom/ns-thermal.c
> new file mode 100644
> index 000000000000..acf3a4de62a4
> --- /dev/null
> +++ b/drivers/thermal/broadcom/ns-thermal.c
> @@ -0,0 +1,98 @@
> +/*
> + * Copyright (C) 2017 Rafa? Mi?ecki <rafal@milecki.pl>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#include <linux/module.h>
> +#include <linux/of_address.h>
> +#include <linux/platform_device.h>
> +#include <linux/thermal.h>
> +
> +#define PVTMON_CONTROL0 0x00
> +#define PVTMON_CONTROL0_SEL_MASK 0x0000000e
> +#define PVTMON_CONTROL0_SEL_TEMP_MONITOR 0x00000000
> +#define PVTMON_CONTROL0_SEL_TEST_MODE 0x0000000e
> +#define PVTMON_STATUS 0x08
> +
> +struct ns_thermal {
> + void __iomem *pvtmon;
> +};
> +
> +static int ns_thermal_get_temp(void *data, int *temp)
> +{
> + struct ns_thermal *ns_thermal = data;
> + u32 val;
> +
> + val = readl(ns_thermal->pvtmon + PVTMON_CONTROL0);
> + if ((val & PVTMON_CONTROL0_SEL_MASK) != PVTMON_CONTROL0_SEL_TEMP_MONITOR) {
> + val &= ~PVTMON_CONTROL0_SEL_MASK;
> + val |= PVTMON_CONTROL0_SEL_TEMP_MONITOR;
I think this is slightly confusing here. If this was off, ORing in 0
will not enable it. I think we need to flip the #define to make it
PVTMON_CONTROL0_SEL_TEMP_MONITOR_DISABLE (or a less crappy name).
then use this line here to toggle it. Something like
val &= ~PVTMON_CONTROL0_SEL_TEMP_MONITOR_DISABLE;
Thanks,
Jon
> + writel(val, ns_thermal->pvtmon + PVTMON_CONTROL0);
> + }
> +
> + val = readl(ns_thermal->pvtmon + PVTMON_STATUS);
> + *temp = (418 - (val * 5556 / 10000)) * 1000;
> +
> + return 0;
> +}
> +
> +const struct thermal_zone_of_device_ops ns_thermal_ops = {
> + .get_temp = ns_thermal_get_temp,
> +};
> +
> +static int ns_thermal_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct ns_thermal *ns_thermal;
> + struct thermal_zone_device *tzd;
> +
> + ns_thermal = devm_kzalloc(dev, sizeof(*ns_thermal), GFP_KERNEL);
> + if (!ns_thermal)
> + return -ENOMEM;
> +
> + ns_thermal->pvtmon = of_iomap(dev_of_node(dev), 0);
> + if (WARN_ON(!ns_thermal->pvtmon))
> + return -ENOENT;
> +
> + tzd = devm_thermal_zone_of_sensor_register(dev, 0, ns_thermal,
> + &ns_thermal_ops);
> + if (IS_ERR(tzd)) {
> + iounmap(ns_thermal->pvtmon);
> + return PTR_ERR(tzd);
> + }
> +
> + platform_set_drvdata(pdev, ns_thermal);
> +
> + return 0;
> +}
> +
> +static int ns_thermal_remove(struct platform_device *pdev)
> +{
> + struct ns_thermal *ns_thermal = platform_get_drvdata(pdev);
> +
> + iounmap(ns_thermal->pvtmon);
> +
> + return 0;
> +}
> +
> +static const struct of_device_id ns_thermal_of_match[] = {
> + { .compatible = "brcm,ns-thermal", },
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, ns_thermal_of_match);
> +
> +static struct platform_driver ns_thermal_driver = {
> + .probe = ns_thermal_probe,
> + .remove = ns_thermal_remove,
> + .driver = {
> + .name = "ns-thermal",
> + .of_match_table = ns_thermal_of_match,
> + },
> +};
> +module_platform_driver(ns_thermal_driver);
> +
> +MODULE_DESCRIPTION("Northstar thermal driver");
> +MODULE_LICENSE("GPL v2");
> --
> 2.11.0
>
next prev parent reply other threads:[~2017-03-24 14:35 UTC|newest]
Thread overview: 31+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <20170318155632.18099-1-zajec5@gmail.com>
2017-03-23 22:30 ` [PATCH V2 1/2] dt-bindings: thermal: add support for Broadcom's Northstar thermal Rafał Miłecki
2017-03-23 22:30 ` [PATCH V2 2/2] thermal: broadcom: add Northstar thermal driver Rafał Miłecki
2017-03-24 14:35 ` Jon Mason [this message]
2017-03-31 7:03 ` Rafał Miłecki
2017-03-31 14:23 ` Jon Mason
2017-03-31 14:49 ` Rafał Miłecki
2017-03-31 17:29 ` Jon Mason
2017-03-31 3:15 ` Eduardo Valentin
2017-03-31 7:08 ` Rafał Miłecki
2017-03-31 3:17 ` [PATCH V2 1/2] dt-bindings: thermal: add support for Broadcom's Northstar thermal Eduardo Valentin
2017-03-31 7:31 ` [PATCH V3 " Rafał Miłecki
2017-03-31 7:31 ` [PATCH V3 2/2] thermal: broadcom: add Northstar thermal driver Rafał Miłecki
2017-03-31 20:11 ` [PATCH V4 1/2] dt-bindings: thermal: add support for Broadcom's Northstar thermal Rafał Miłecki
2017-03-31 20:11 ` [PATCH V4 2/2] thermal: broadcom: add Northstar thermal driver Rafał Miłecki
2017-04-01 19:54 ` Eduardo Valentin
2017-04-01 20:20 ` Florian Fainelli
2017-04-01 21:41 ` Rafał Miłecki
2017-04-01 19:51 ` [PATCH V4 1/2] dt-bindings: thermal: add support for Broadcom's Northstar thermal Eduardo Valentin
2017-04-01 21:50 ` Rafał Miłecki
2017-04-02 4:13 ` Eduardo Valentin
2017-04-03 3:07 ` Jon Mason
2017-04-03 14:54 ` Jon Mason
2017-04-03 14:57 ` Rafał Miłecki
2017-04-03 15:48 ` [PATCH V5 " Rafał Miłecki
2017-04-03 15:48 ` [PATCH V5 2/2] thermal: broadcom: add Northstar thermal driver Rafał Miłecki
2017-04-07 4:42 ` Eduardo Valentin
2017-04-14 12:16 ` Rafał Miłecki
2017-04-14 15:16 ` Eduardo Valentin
2017-04-14 15:19 ` Rafał Miłecki
2017-04-17 20:09 ` Stefan Wahren
2017-04-10 15:00 ` [PATCH V5 1/2] dt-bindings: thermal: add support for Broadcom's Northstar thermal Rob Herring
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20170324143535.GA31953@broadcom.com \
--to=jon.mason@broadcom.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).