[PATCH v2 0/4] dt-bindings: Firmware node binding for ZynqMP core

[PATCH v2 0/4] dt-bindings: Firmware node binding for ZynqMP core

[Jolly Shah]

Base firmware node and clock child node binding are part of mainline kernel. This patchset adds documentation to describe rest of the firmware child node bindings. 
Complete firmware DT node example is shown below for ease of understanding:

firmware {
	zynqmp_firmware: zynqmp-firmware {
		compatible = "xlnx,zynqmp-firmware";
		method = "smc";
		#power-domain-cells = <1>;
		#reset-cells = <1>;

		zynqmp_clk: clock-controller {
			#clock-cells = <1>;
			compatible = "xlnx,zynqmp-clk";
			clocks = <&pss_ref_clk>, <&video_clk>, <&pss_alt_ref_clk>, <&aux_ref_clk>, <&gt_crx_ref_clk>;
			clock-names = "pss_ref_clk", "video_clk", "pss_alt_ref_clk","aux_ref_clk", "gt_crx_ref_clk";
		};

		zynqmp_power: zynqmp-power {
			compatible = "xlnx,zynqmp-power";
			interrupts = <0 35 4>;
		};
		
		pinctrl0: pinctrl@ff180000 {
			compatible = "xlnx,zynqmp-pinctrl";

			pinctrl_uart1_default: uart1-default {
				mux {
					groups = "uart0_4_grp";
					function = "uart0";
				};
	
				conf {
					groups = "uart0_4_grp";
					slew-rate = <SLEW_RATE_SLOW>;
					io-standard = <IO_STANDARD_LVCMOS18>;
				};
	
				conf-rx {
					pins = "MIO18";
					bias-high-impedance;
				};
	
				conf-tx {
					pins = "MIO19";
					bias-disable;
					schmitt-cmos = <PIN_INPUT_TYPE_CMOS>;
				};
			};
		};
	};
};
Nava kishore Manne (1):
  dt-bindings: reset: Add bindings for ZynqMP reset driver

Rajan Vaja (3):
  dt-bindings: power: Add ZynqMP power domain bindings
  dt-bindings: soc: Add ZynqMP PM bindings
  dt-bindings: pinctrl: Add ZynqMP pin controller bindings

 .../bindings/pinctrl/xlnx,zynqmp-pinctrl.txt       | 275 +++++++++++++++++++++
 .../bindings/power/reset/xlnx,zynqmp-power.txt     |  25 ++
 .../bindings/power/xlnx,zynqmp-genpd.txt           |  34 +++
 .../bindings/reset/xlnx,zynqmp-reset.txt           | 148 +++++++++++
 include/dt-bindings/power/xlnx-zynqmp-power.h      |  39 +++
 5 files changed, 521 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pinctrl/xlnx,zynqmp-pinctrl.txt
 create mode 100644 Documentation/devicetree/bindings/power/reset/xlnx,zynqmp-power.txt
 create mode 100644 Documentation/devicetree/bindings/power/xlnx,zynqmp-genpd.txt
 create mode 100644 Documentation/devicetree/bindings/reset/xlnx,zynqmp-reset.txt
 create mode 100644 include/dt-bindings/power/xlnx-zynqmp-power.h

-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 1/4] dt-bindings: power: Add ZynqMP power domain bindings

[Jolly Shah]

From: Rajan Vaja <rajan.vaja@xilinx.com>

Add documentation to describe ZynqMP power domain bindings.

Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
---
 .../bindings/power/xlnx,zynqmp-genpd.txt           | 34 +++++++++++++++++++
 include/dt-bindings/power/xlnx-zynqmp-power.h      | 39 ++++++++++++++++++++++
 2 files changed, 73 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/power/xlnx,zynqmp-genpd.txt
 create mode 100644 include/dt-bindings/power/xlnx-zynqmp-power.h

diff --git a/Documentation/devicetree/bindings/power/xlnx,zynqmp-genpd.txt b/Documentation/devicetree/bindings/power/xlnx,zynqmp-genpd.txt
new file mode 100644
index 0000000..3c7f237
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/xlnx,zynqmp-genpd.txt
@@ -0,0 +1,34 @@
+-----------------------------------------------------------
+Device Tree Bindings for the Xilinx Zynq MPSoC PM domains
+-----------------------------------------------------------
+The binding for zynqmp-power-controller follow the common
+generic PM domain binding[1].
+
+[1] Documentation/devicetree/bindings/power/power_domain.txt
+
+== Zynq MPSoC Generic PM Domain Node ==
+
+Required property:
+ - Below property should be in zynqmp-firmware node.
+ - #power-domain-cells:	Number of cells in a PM domain specifier. Must be 1.
+
+Power domain ID indexes are mentioned in
+include/dt-bindings/power/xlnx-zynqmp-power.h.
+
+-------
+Example
+-------
+
+firmware {
+	zynqmp_firmware: zynqmp-firmware {
+		...
+		#power-domain-cells = <1>;
+		...
+	};
+};
+
+sata {
+	...
+	power-domains = <&zynqmp_firmware 2>;
+	...
+};
diff --git a/include/dt-bindings/power/xlnx-zynqmp-power.h b/include/dt-bindings/power/xlnx-zynqmp-power.h
new file mode 100644
index 0000000..1bc9636
--- /dev/null
+++ b/include/dt-bindings/power/xlnx-zynqmp-power.h
@@ -0,0 +1,39 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ *  Copyright (C) 2018 Xilinx, Inc.
+ */
+
+#ifndef _DT_BINDINGS_ZYNQMP_POWER_H
+#define _DT_BINDINGS_ZYNQMP_POWER_H
+
+#define		PD_USB_0	0
+#define		PD_USB_1	1
+#define		PD_SATA		2
+#define		PD_SPI_0	3
+#define		PD_SPI_1	4
+#define		PD_UART_0	5
+#define		PD_UART_1	6
+#define		PD_ETH_0	7
+#define		PD_ETH_1	8
+#define		PD_ETH_2	9
+#define		PD_ETH_3	10
+#define		PD_I2C_0	11
+#define		PD_I2C_1	12
+#define		PD_DP		13
+#define		PD_GDMA		14
+#define		PD_ADMA		15
+#define		PD_TTC_0	16
+#define		PD_TTC_1	17
+#define		PD_TTC_2	18
+#define		PD_TTC_3	19
+#define		PD_SD_0		20
+#define		PD_SD_1		21
+#define		PD_NAND		22
+#define		PD_QSPI		23
+#define		PD_GPIO		24
+#define		PD_CAN_0	25
+#define		PD_CAN_1	26
+#define		PD_PCIE		27
+#define		PD_GPU		28
+
+#endif
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 1/4] dt-bindings: power: Add ZynqMP power domain bindings

[Rob Herring]

On Fri, 4 Jan 2019 13:56:19 -0800, Jolly Shah wrote:
> From: Rajan Vaja <rajan.vaja@xilinx.com>
> 
> Add documentation to describe ZynqMP power domain bindings.
> 
> Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
> Signed-off-by: Jolly Shah <jollys@xilinx.com>
> ---
>  .../bindings/power/xlnx,zynqmp-genpd.txt           | 34 +++++++++++++++++++
>  include/dt-bindings/power/xlnx-zynqmp-power.h      | 39 ++++++++++++++++++++++
>  2 files changed, 73 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/power/xlnx,zynqmp-genpd.txt
>  create mode 100644 include/dt-bindings/power/xlnx-zynqmp-power.h
> 

Reviewed-by: Rob Herring <robh@kernel.org>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 2/4] dt-bindings: soc: Add ZynqMP PM bindings

[Jolly Shah]

From: Rajan Vaja <rajan.vaja@xilinx.com>

Add documentation to describe Xilinx ZynqMP power management
bindings.

Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
---
 .../bindings/power/reset/xlnx,zynqmp-power.txt     | 25 ++++++++++++++++++++++
 1 file changed, 25 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/power/reset/xlnx,zynqmp-power.txt

diff --git a/Documentation/devicetree/bindings/power/reset/xlnx,zynqmp-power.txt b/Documentation/devicetree/bindings/power/reset/xlnx,zynqmp-power.txt
new file mode 100644
index 0000000..d366f1e
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/reset/xlnx,zynqmp-power.txt
@@ -0,0 +1,25 @@
+--------------------------------------------------------------------
+Device Tree Bindings for the Xilinx Zynq MPSoC Power Management
+--------------------------------------------------------------------
+The zynqmp-power node describes the power management configurations.
+It will control remote suspend/shutdown interfaces.
+
+Required properties:
+ - compatible:		Must contain:	"xlnx,zynqmp-power"
+ - interrupts:		Interrupt specifier
+
+-------
+Example
+-------
+
+firmware {
+	zynqmp_firmware: zynqmp-firmware {
+		compatible = "xlnx,zynqmp-firmware";
+		method = "smc";
+
+		zynqmp_power: zynqmp-power {
+			compatible = "xlnx,zynqmp-power";
+			interrupts = <0 35 4>;
+		};
+	};
+};
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 2/4] dt-bindings: soc: Add ZynqMP PM bindings

[Rob Herring]

On Fri, 4 Jan 2019 13:56:20 -0800, Jolly Shah wrote:
> From: Rajan Vaja <rajan.vaja@xilinx.com>
> 
> Add documentation to describe Xilinx ZynqMP power management
> bindings.
> 
> Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
> Signed-off-by: Jolly Shah <jollys@xilinx.com>
> ---
>  .../bindings/power/reset/xlnx,zynqmp-power.txt     | 25 ++++++++++++++++++++++
>  1 file changed, 25 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/power/reset/xlnx,zynqmp-power.txt
> 

Reviewed-by: Rob Herring <robh@kernel.org>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 3/4] dt-bindings: reset: Add bindings for ZynqMP reset driver

[Jolly Shah]

From: Nava kishore Manne <nava.manne@xilinx.com>

Add documentation to describe Xilinx ZynqMP reset driver
bindings.

Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
---
 .../bindings/reset/xlnx,zynqmp-reset.txt           | 148 +++++++++++++++++++++
 1 file changed, 148 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/reset/xlnx,zynqmp-reset.txt

diff --git a/Documentation/devicetree/bindings/reset/xlnx,zynqmp-reset.txt b/Documentation/devicetree/bindings/reset/xlnx,zynqmp-reset.txt
new file mode 100644
index 0000000..e9c1af8
--- /dev/null
+++ b/Documentation/devicetree/bindings/reset/xlnx,zynqmp-reset.txt
@@ -0,0 +1,148 @@
+--------------------------------------------------------------------------
+ =  Zynq UltraScale+ MPSoC reset driver binding =
+--------------------------------------------------------------------------
+The Zynq UltraScale+ MPSoC has several different resets.
+
+See Chapter 36 of the Zynq UltraScale+ MPSoC TRM (UG) for more information
+about zynqmp resets.
+
+Please also refer to reset.txt in this directory for common reset
+controller binding usage.
+
+Required Properties:
+- #reset-cells:	Specifies the number of cells needed to encode reset
+		line, should be 1
+
+Reset outputs:
+	0   :PCIE config reset.
+	1   :PCIE bridge block level reset (AXI interface).
+	2   :PCIE control block level,reset.
+	3   :Display Port block level reset (includes DPDMA).
+	4   :FPD WDT reset.
+	5   :AF_FM5 block level reset.
+	6   :AF_FM4 block level reset.
+	7   :AF_FM3 block level reset.
+	8   :AF_FM2 block level reset.
+	9   :AF_FM1 block level reset.
+	10  :AF_FM0 block level reset.
+	11  :GDMA block level reset.
+	12  :Pixel Processor (GPU_PP1) block level reset.
+	13  :Pixel Processor (GPU_PP0) block level reset.
+	14  :GPU block level reset.
+	15  :GT block level reset.
+	16  :Sata block level reset.
+	17  :ACPU3 power on reset.
+	18  :ACPU2 power on reset.
+	19  :ACPU1 power on reset.
+	20  :ACPU0 power on reset.
+	21  :APU L2 reset.
+	22  :ACPU3 reset.
+	23  :ACPU2 reset.
+	24  :ACPU1 reset.
+	25  :ACPU0 reset.
+	26  :DDR block level reset inside of the DDR Sub System.
+	27  :APM block level reset inside of the DDR Sub System.
+	28  :soft reset.
+	29  :GEM 0 reset.
+	30  :GEM 1 reset.
+	31  :GEM 2 reset.
+	32  :GEM 3 reset.
+	33  :qspi reset.
+	34  :uart0 reset.
+	35  :uart1 reset.
+	36  :spi0 reset.
+	37  :spi1 reset.
+	38  :sdio0 reset.
+	39  :sdio1 reset.
+	40  :can0 reset.
+	41  :can1 reset.
+	42  :i2c0 reset.
+	43  :i2c1 reset.
+	44  :ttc0 reset.
+	45  :ttc1 reset.
+	46  :ttc2 reset.
+	47  :ttc3 reset.
+	48  :swdt reset.
+	49  :nand reset.
+	50  :adma reset.
+	51  :gpio reset.
+	52  :iou_cc reset.
+	53  :timestamp reset.
+	54  :rpu_r50 reset.
+	55  :rpu r51 reset.
+	56  :rpu_amba reset.
+	57  :ocm reset.
+	58  :rpu_pge reset.
+	59  :usb0_core reset.
+	60  :usb1_core reset.
+	61  :usb0_hiber reset.
+	62  :usb1_hiber reset.
+	63  :usb0_apb reset.
+	64  :usb1_apb reset.
+	65  :ipi reset.
+	66  :apm reset.
+	67  :rtc reset.
+	68  :sysmon reset.
+	69  :afi_fm6 reset.
+	70  :lpd_swdt reset.
+	71  :fpd_reset.
+	72  :rpu_dbg1 reset.
+	73  :rpu_dbg0 reset.
+	74  :dbg_lpd reset.
+	75  :dbg_fpd reset.
+	76  :apll reset.
+	77  :dpll reset.
+	78  :vpll reset.
+	79  :iopll reset.
+	80  :rpll reset.
+	81  :gpio_pl_0 reset.
+	82  :gpio_pl_1 reset.
+	83  :gpio_pl_2 reset.
+	84  :gpio_pl_3 reset.
+	85  :gpio_pl_4 reset.
+	86  :gpio_pl_5 reset.
+	87  :gpio_pl_6 reset.
+	88  :gpio_pl_7 reset.
+	89  :gpio_pl_8 reset.
+	90  :gpio_pl_9 reset.
+	91  :gpio_pl_10 reset.
+	92  :gpio_pl_11 reset.
+	93  :gpio_pl_12 reset.
+	94  :gpio_pl_13 reset.
+	95  :gpio_pl_14 reset.
+	96  :gpio_pl_15 reset.
+	97  :gpio_pl_16 reset.
+	98  :gpio_pl_17 reset.
+	99  :gpio_pl_18 reset.
+	100 :gpio_pl_19 reset.
+	101 :gpio_pl_20 reset.
+	102 :gpio_pl_21 reset.
+	103 :gpio_pl_22 reset.
+	104 :gpio_pl_23 reset.
+	105 :gpio_pl_24 reset.
+	106 :gpio_pl_25 reset.
+	107 :gpio_pl_26 reset.
+	108 :gpio_pl_27 reset.
+	109 :gpio_pl_28 reset.
+	110 :gpio_pl_29 reset.
+	111 :gpio_pl_30 reset.
+	112 :gpio_pl_31 reset.
+	113 :rpu_ls reset.
+	114 :ps_only reset.
+	115 :pl reset.
+	116 :ps_pl0 reset
+	117 :ps_pl1 reset
+	118 :ps_pl2 reset
+	119 :ps_pl3 reset
+
+-------
+Example
+-------
+
+firmware {
+	zynqmp_firmware: zynqmp-firmware {
+		...
+		#reset-cells = <1>;
+		...
+	};
+};
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 3/4] dt-bindings: reset: Add bindings for ZynqMP reset driver

[Rob Herring]

On Fri, Jan 04, 2019 at 01:56:21PM -0800, Jolly Shah wrote:
> From: Nava kishore Manne <nava.manne@xilinx.com>
> 
> Add documentation to describe Xilinx ZynqMP reset driver
> bindings.
> 
> Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com>
> Signed-off-by: Jolly Shah <jollys@xilinx.com>
> ---
>  .../bindings/reset/xlnx,zynqmp-reset.txt           | 148 +++++++++++++++++++++
>  1 file changed, 148 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/reset/xlnx,zynqmp-reset.txt
> 
> diff --git a/Documentation/devicetree/bindings/reset/xlnx,zynqmp-reset.txt b/Documentation/devicetree/bindings/reset/xlnx,zynqmp-reset.txt
> new file mode 100644
> index 0000000..e9c1af8
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/reset/xlnx,zynqmp-reset.txt
> @@ -0,0 +1,148 @@
> +--------------------------------------------------------------------------
> + =  Zynq UltraScale+ MPSoC reset driver binding =
> +--------------------------------------------------------------------------
> +The Zynq UltraScale+ MPSoC has several different resets.
> +
> +See Chapter 36 of the Zynq UltraScale+ MPSoC TRM (UG) for more information
> +about zynqmp resets.
> +
> +Please also refer to reset.txt in this directory for common reset
> +controller binding usage.
> +
> +Required Properties:
> +- #reset-cells:	Specifies the number of cells needed to encode reset
> +		line, should be 1
> +
> +Reset outputs:
> +	0   :PCIE config reset.
> +	1   :PCIE bridge block level reset (AXI interface).
> +	2   :PCIE control block level,reset.

Presumably, you will have a header for all these? If so, then don't 
define them here.

> +	3   :Display Port block level reset (includes DPDMA).
> +	4   :FPD WDT reset.
> +	5   :AF_FM5 block level reset.
> +	6   :AF_FM4 block level reset.
> +	7   :AF_FM3 block level reset.
> +	8   :AF_FM2 block level reset.
> +	9   :AF_FM1 block level reset.
> +	10  :AF_FM0 block level reset.
> +	11  :GDMA block level reset.
> +	12  :Pixel Processor (GPU_PP1) block level reset.
> +	13  :Pixel Processor (GPU_PP0) block level reset.
> +	14  :GPU block level reset.
> +	15  :GT block level reset.
> +	16  :Sata block level reset.
> +	17  :ACPU3 power on reset.
> +	18  :ACPU2 power on reset.
> +	19  :ACPU1 power on reset.
> +	20  :ACPU0 power on reset.
> +	21  :APU L2 reset.
> +	22  :ACPU3 reset.
> +	23  :ACPU2 reset.
> +	24  :ACPU1 reset.
> +	25  :ACPU0 reset.
> +	26  :DDR block level reset inside of the DDR Sub System.
> +	27  :APM block level reset inside of the DDR Sub System.
> +	28  :soft reset.
> +	29  :GEM 0 reset.
> +	30  :GEM 1 reset.
> +	31  :GEM 2 reset.
> +	32  :GEM 3 reset.
> +	33  :qspi reset.
> +	34  :uart0 reset.
> +	35  :uart1 reset.
> +	36  :spi0 reset.
> +	37  :spi1 reset.
> +	38  :sdio0 reset.
> +	39  :sdio1 reset.
> +	40  :can0 reset.
> +	41  :can1 reset.
> +	42  :i2c0 reset.
> +	43  :i2c1 reset.
> +	44  :ttc0 reset.
> +	45  :ttc1 reset.
> +	46  :ttc2 reset.
> +	47  :ttc3 reset.
> +	48  :swdt reset.
> +	49  :nand reset.
> +	50  :adma reset.
> +	51  :gpio reset.
> +	52  :iou_cc reset.
> +	53  :timestamp reset.
> +	54  :rpu_r50 reset.
> +	55  :rpu r51 reset.
> +	56  :rpu_amba reset.
> +	57  :ocm reset.
> +	58  :rpu_pge reset.
> +	59  :usb0_core reset.
> +	60  :usb1_core reset.
> +	61  :usb0_hiber reset.
> +	62  :usb1_hiber reset.
> +	63  :usb0_apb reset.
> +	64  :usb1_apb reset.
> +	65  :ipi reset.
> +	66  :apm reset.
> +	67  :rtc reset.
> +	68  :sysmon reset.
> +	69  :afi_fm6 reset.
> +	70  :lpd_swdt reset.
> +	71  :fpd_reset.
> +	72  :rpu_dbg1 reset.
> +	73  :rpu_dbg0 reset.
> +	74  :dbg_lpd reset.
> +	75  :dbg_fpd reset.
> +	76  :apll reset.
> +	77  :dpll reset.
> +	78  :vpll reset.
> +	79  :iopll reset.
> +	80  :rpll reset.
> +	81  :gpio_pl_0 reset.
> +	82  :gpio_pl_1 reset.
> +	83  :gpio_pl_2 reset.
> +	84  :gpio_pl_3 reset.
> +	85  :gpio_pl_4 reset.
> +	86  :gpio_pl_5 reset.
> +	87  :gpio_pl_6 reset.
> +	88  :gpio_pl_7 reset.
> +	89  :gpio_pl_8 reset.
> +	90  :gpio_pl_9 reset.
> +	91  :gpio_pl_10 reset.
> +	92  :gpio_pl_11 reset.
> +	93  :gpio_pl_12 reset.
> +	94  :gpio_pl_13 reset.
> +	95  :gpio_pl_14 reset.
> +	96  :gpio_pl_15 reset.
> +	97  :gpio_pl_16 reset.
> +	98  :gpio_pl_17 reset.
> +	99  :gpio_pl_18 reset.
> +	100 :gpio_pl_19 reset.
> +	101 :gpio_pl_20 reset.
> +	102 :gpio_pl_21 reset.
> +	103 :gpio_pl_22 reset.
> +	104 :gpio_pl_23 reset.
> +	105 :gpio_pl_24 reset.
> +	106 :gpio_pl_25 reset.
> +	107 :gpio_pl_26 reset.
> +	108 :gpio_pl_27 reset.
> +	109 :gpio_pl_28 reset.
> +	110 :gpio_pl_29 reset.
> +	111 :gpio_pl_30 reset.
> +	112 :gpio_pl_31 reset.
> +	113 :rpu_ls reset.
> +	114 :ps_only reset.
> +	115 :pl reset.
> +	116 :ps_pl0 reset
> +	117 :ps_pl1 reset
> +	118 :ps_pl2 reset
> +	119 :ps_pl3 reset
> +
> +-------
> +Example
> +-------
> +
> +firmware {
> +	zynqmp_firmware: zynqmp-firmware {
> +		...
> +		#reset-cells = <1>;
> +		...
> +	};
> +};
> -- 
> 2.7.4
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 4/4] dt-bindings: pinctrl: Add ZynqMP pin controller bindings

[Jolly Shah]

From: Rajan Vaja <rajan.vaja@xilinx.com>

Add documentation to describe Xilinx ZynqMP pin controller
bindings.

Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
---
 .../bindings/pinctrl/xlnx,zynqmp-pinctrl.txt       | 275 +++++++++++++++++++++
 1 file changed, 275 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pinctrl/xlnx,zynqmp-pinctrl.txt

diff --git a/Documentation/devicetree/bindings/pinctrl/xlnx,zynqmp-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/xlnx,zynqmp-pinctrl.txt
new file mode 100644
index 0000000..acf44a5
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/xlnx,zynqmp-pinctrl.txt
@@ -0,0 +1,275 @@
+	Binding for Xilinx ZynqMP Pinctrl
+
+Required properties:
+- compatible: "xlnx,zynqmp-pinctrl"
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+ZynqMP's pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, slew rate, etc.
+
+Each configuration node can consist of multiple nodes describing the pinmux and
+pinconf options. Those nodes can be pinmux nodes or pinconf nodes.
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Required properties for pinmux nodes are:
+ - groups: A list of pinmux groups.
+ - function: The name of a pinmux function to activate for the specified set
+   of groups.
+
+Required properties for configuration nodes:
+One of:
+ - pins: A list of pin names
+ - groups: A list of pinmux groups.
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pinmux subnode:
+ groups, function
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pinconf subnode:
+ groups, pins, bias-disable, bias-pull-up, bias-pull-down, slew-rate
+
+ Valid arguments for 'slew-rate' are 'SLEW_RATE_SLOW' and 'SLEW_RATE_FAST' to
+ select between slow and fast respectively.
+
+ Valid values for groups are:
+ ethernet0_0_grp, ethernet1_0_grp, ethernet2_0_grp,
+ ethernet3_0_grp, gemtsu0_0_grp, gemtsu0_1_grp,
+ gemtsu0_2_grp, mdio0_0_grp, mdio1_0_grp,
+ mdio1_1_grp, mdio2_0_grp, mdio3_0_grp,
+ qspi0_0_grp, qspi_ss_0_grp, qspi_fbclk_0_grp,
+ spi0_0_grp, spi0_ss_0_grp, spi0_ss_1_grp,
+ spi0_ss_2_grp, spi0_1_grp, spi0_ss_3_grp,
+ spi0_ss_4_grp, spi0_ss_5_grp, spi0_2_grp,
+ spi0_ss_6_grp, spi0_ss_7_grp, spi0_ss_8_grp,
+ spi0_3_grp, spi0_ss_9_grp, spi0_ss_10_grp,
+ spi0_ss_11_grp, spi0_4_grp, spi0_ss_12_grp,
+ spi0_ss_13_grp, spi0_ss_14_grp, spi0_5_grp,
+ spi0_ss_15_grp, spi0_ss_16_grp, spi0_ss_17_grp,
+ spi1_0_grp, spi1_ss_0_grp, spi1_ss_1_grp,
+ spi1_ss_2_grp, spi1_1_grp, spi1_ss_3_grp,
+ spi1_ss_4_grp, spi1_ss_5_grp, spi1_2_grp,
+ spi1_ss_6_grp, spi1_ss_7_grp, spi1_ss_8_grp,
+ spi1_3_grp, spi1_ss_9_grp, spi1_ss_10_grp,
+ spi1_ss_11_grp, spi1_4_grp, spi1_ss_12_grp,
+ spi1_ss_13_grp, spi1_ss_14_grp, spi1_5_grp,
+ spi1_ss_15_grp, spi1_ss_16_grp, spi1_ss_17_grp,
+ sdio0_0_grp, sdio0_1_grp, sdio0_2_grp,
+ sdio0_3_grp, sdio0_4_grp, sdio0_5_grp,
+ sdio0_6_grp, sdio0_7_grp, sdio0_8_grp,
+ sdio0_9_grp, sdio0_10_grp, sdio0_11_grp,
+ sdio0_12_grp, sdio0_13_grp, sdio0_14_grp,
+ sdio0_15_grp, sdio0_16_grp, sdio0_17_grp,
+ sdio0_18_grp, sdio0_19_grp, sdio0_20_grp,
+ sdio0_21_grp, sdio0_22_grp, sdio0_23_grp,
+ sdio0_24_grp, sdio0_25_grp, sdio0_26_grp,
+ sdio0_27_grp, sdio0_28_grp, sdio0_29_grp,
+ sdio0_30_grp, sdio0_31_grp, sdio0_32_grp,
+ sdio0_pc_0_grp, sdio0_cd_0_grp, sdio0_wp_0_grp,
+ sdio0_pc_1_grp, sdio0_cd_1_grp, sdio0_wp_1_grp,
+ sdio0_pc_2_grp, sdio0_cd_2_grp, sdio0_wp_2_grp,
+ sdio1_0_grp, sdio1_1_grp, sdio1_2_grp,
+ sdio1_3_grp, sdio1_4_grp, sdio1_5_grp,
+ sdio1_6_grp, sdio1_7_grp, sdio1_8_grp,
+ sdio1_9_grp, sdio1_10_grp, sdio1_11_grp,
+ sdio1_12_grp, sdio1_13_grp, sdio1_14_grp,
+ sdio1_15_grp, sdio1_pc_0_grp, sdio1_cd_0_grp,
+ sdio1_wp_0_grp, sdio1_pc_1_grp, sdio1_cd_1_grp,
+ sdio1_wp_1_grp, nand0_0_grp, nand0_ce_0_grp,
+ nand0_rb_0_grp, nand0_dqs_0_grp, nand0_ce_1_grp,
+ nand0_rb_1_grp, nand0_dqs_1_grp, can0_0_grp,
+ can0_1_grp, can0_2_grp, can0_3_grp,
+ can0_4_grp, can0_5_grp, can0_6_grp,
+ can0_7_grp, can0_8_grp, can0_9_grp,
+ can0_10_grp, can0_11_grp, can0_12_grp,
+ can0_13_grp, can0_14_grp, can0_15_grp,
+ can0_16_grp, can0_17_grp, can0_18_grp,
+ can1_0_grp, can1_1_grp, can1_2_grp,
+ can1_3_grp, can1_4_grp, can1_5_grp,
+ can1_6_grp, can1_7_grp, can1_8_grp,
+ can1_9_grp, can1_10_grp, can1_11_grp,
+ can1_12_grp, can1_13_grp, can1_14_grp,
+ can1_15_grp, can1_16_grp, can1_17_grp,
+ can1_18_grp, can1_19_grp, uart0_0_grp,
+ uart0_1_grp, uart0_2_grp, uart0_3_grp,
+ uart0_4_grp, uart0_5_grp, uart0_6_grp,
+ uart0_7_grp, uart0_8_grp, uart0_9_grp,
+ uart0_10_grp, uart0_11_grp, uart0_12_grp,
+ uart0_13_grp, uart0_14_grp, uart0_15_grp,
+ uart0_16_grp, uart0_17_grp, uart0_18_grp,
+ uart1_0_grp, uart1_1_grp, uart1_2_grp,
+ uart1_3_grp, uart1_4_grp, uart1_5_grp,
+ uart1_6_grp, uart1_7_grp, uart1_8_grp,
+ uart1_9_grp, uart1_10_grp, uart1_11_grp,
+ uart1_12_grp, uart1_13_grp, uart1_14_grp,
+ uart1_15_grp, uart1_16_grp, uart1_17_grp,
+ uart1_18_grp, i2c0_0_grp, i2c0_1_grp,
+ i2c0_2_grp, i2c0_3_grp, i2c0_4_grp,
+ i2c0_5_grp, i2c0_6_grp, i2c0_7_grp,
+ i2c0_8_grp, i2c0_9_grp, i2c0_10_grp,
+ i2c0_11_grp, i2c0_12_grp, i2c0_13_grp,
+ i2c0_14_grp, i2c0_15_grp, i2c0_16_grp,
+ i2c0_17_grp, i2c0_18_grp, i2c1_0_grp,
+ i2c1_1_grp, i2c1_2_grp, i2c1_3_grp,
+ i2c1_4_grp, i2c1_5_grp, i2c1_6_grp,
+ i2c1_7_grp, i2c1_8_grp, i2c1_9_grp,
+ i2c1_10_grp, i2c1_11_grp, i2c1_12_grp,
+ i2c1_13_grp, i2c1_14_grp, i2c1_15_grp,
+ i2c1_16_grp, i2c1_17_grp, i2c1_18_grp,
+ i2c1_19_grp, ttc0_clk_0_grp, ttc0_wav_0_grp,
+ ttc0_clk_1_grp, ttc0_wav_1_grp, ttc0_clk_2_grp,
+ ttc0_wav_2_grp, ttc0_clk_3_grp, ttc0_wav_3_grp,
+ ttc0_clk_4_grp, ttc0_wav_4_grp, ttc0_clk_5_grp,
+ ttc0_wav_5_grp, ttc0_clk_6_grp, ttc0_wav_6_grp,
+ ttc0_clk_7_grp, ttc0_wav_7_grp, ttc0_clk_8_grp,
+ ttc0_wav_8_grp, ttc1_clk_0_grp, ttc1_wav_0_grp,
+ ttc1_clk_1_grp, ttc1_wav_1_grp, ttc1_clk_2_grp,
+ ttc1_wav_2_grp, ttc1_clk_3_grp, ttc1_wav_3_grp,
+ ttc1_clk_4_grp, ttc1_wav_4_grp, ttc1_clk_5_grp,
+ ttc1_wav_5_grp, ttc1_clk_6_grp, ttc1_wav_6_grp,
+ ttc1_clk_7_grp, ttc1_wav_7_grp, ttc1_clk_8_grp,
+ ttc1_wav_8_grp, ttc2_clk_0_grp, ttc2_wav_0_grp,
+ ttc2_clk_1_grp, ttc2_wav_1_grp, ttc2_clk_2_grp,
+ ttc2_wav_2_grp, ttc2_clk_3_grp, ttc2_wav_3_grp,
+ ttc2_clk_4_grp, ttc2_wav_4_grp, ttc2_clk_5_grp,
+ ttc2_wav_5_grp, ttc2_clk_6_grp, ttc2_wav_6_grp,
+ ttc2_clk_7_grp, ttc2_wav_7_grp, ttc2_clk_8_grp,
+ ttc2_wav_8_grp, ttc3_clk_0_grp, ttc3_wav_0_grp,
+ ttc3_clk_1_grp, ttc3_wav_1_grp, ttc3_clk_2_grp,
+ ttc3_wav_2_grp, ttc3_clk_3_grp, ttc3_wav_3_grp,
+ ttc3_clk_4_grp, ttc3_wav_4_grp, ttc3_clk_5_grp,
+ ttc3_wav_5_grp, ttc3_clk_6_grp, ttc3_wav_6_grp,
+ ttc3_clk_7_grp, ttc3_wav_7_grp, ttc3_clk_8_grp,
+ ttc3_wav_8_grp, swdt0_clk_0_grp, swdt0_rst_0_grp,
+ swdt0_clk_1_grp, swdt0_rst_1_grp, swdt0_clk_2_grp,
+ swdt0_rst_2_grp, swdt0_clk_3_grp, swdt0_rst_3_grp,
+ swdt0_clk_4_grp, swdt0_rst_4_grp, swdt0_clk_5_grp,
+ swdt0_rst_5_grp, swdt0_clk_6_grp, swdt0_rst_6_grp,
+ swdt0_clk_7_grp, swdt0_rst_7_grp, swdt0_clk_8_grp,
+ swdt0_rst_8_grp, swdt0_clk_9_grp, swdt0_rst_9_grp,
+ swdt0_clk_10_grp, swdt0_rst_10_grp, swdt0_clk_11_grp,
+ swdt0_rst_11_grp, swdt0_clk_12_grp, swdt0_rst_12_grp,
+ swdt1_clk_0_grp, swdt1_rst_0_grp, swdt1_clk_1_grp,
+ swdt1_rst_1_grp, swdt1_clk_2_grp, swdt1_rst_2_grp,
+ swdt1_clk_3_grp, swdt1_rst_3_grp, swdt1_clk_4_grp,
+ swdt1_rst_4_grp, swdt1_clk_5_grp, swdt1_rst_5_grp,
+ swdt1_clk_6_grp, swdt1_rst_6_grp, swdt1_clk_7_grp,
+ swdt1_rst_7_grp, swdt1_clk_8_grp, swdt1_rst_8_grp,
+ swdt1_clk_9_grp, swdt1_rst_9_grp, swdt1_clk_10_grp,
+ swdt1_rst_10_grp, swdt1_clk_11_grp, swdt1_rst_11_grp,
+ swdt1_clk_12_grp, swdt1_rst_12_grp, gpio0_0_grp,
+ gpio0_1_grp, gpio0_2_grp, gpio0_3_grp,
+ gpio0_4_grp, gpio0_5_grp, gpio0_6_grp,
+ gpio0_7_grp, gpio0_8_grp, gpio0_9_grp,
+ gpio0_10_grp, gpio0_11_grp, gpio0_12_grp,
+ gpio0_13_grp, gpio0_14_grp, gpio0_15_grp,
+ gpio0_16_grp, gpio0_17_grp, gpio0_18_grp,
+ gpio0_19_grp, gpio0_20_grp, gpio0_21_grp,
+ gpio0_22_grp, gpio0_23_grp, gpio0_24_grp,
+ gpio0_25_grp, gpio0_26_grp, gpio0_27_grp,
+ gpio0_28_grp, gpio0_29_grp, gpio0_30_grp,
+ gpio0_31_grp, gpio0_32_grp, gpio0_33_grp,
+ gpio0_34_grp, gpio0_35_grp, gpio0_36_grp,
+ gpio0_37_grp, gpio0_38_grp, gpio0_39_grp,
+ gpio0_40_grp, gpio0_41_grp, gpio0_42_grp,
+ gpio0_43_grp, gpio0_44_grp, gpio0_45_grp,
+ gpio0_46_grp, gpio0_47_grp, gpio0_48_grp,
+ gpio0_49_grp, gpio0_50_grp, gpio0_51_grp,
+ gpio0_52_grp, gpio0_53_grp, gpio0_54_grp,
+ gpio0_55_grp, gpio0_56_grp, gpio0_57_grp,
+ gpio0_58_grp, gpio0_59_grp, gpio0_60_grp,
+ gpio0_61_grp, gpio0_62_grp, gpio0_63_grp,
+ gpio0_64_grp, gpio0_65_grp, gpio0_66_grp,
+ gpio0_67_grp, gpio0_68_grp, gpio0_69_grp,
+ gpio0_70_grp, gpio0_71_grp, gpio0_72_grp,
+ gpio0_73_grp, gpio0_74_grp, gpio0_75_grp,
+ gpio0_76_grp, gpio0_77_grp, usb0_0_grp,
+ usb1_0_grp, pmu0_0_grp, pmu0_1_grp,
+ pmu0_2_grp, pmu0_3_grp, pmu0_4_grp,
+ pmu0_5_grp, pmu0_6_grp, pmu0_7_grp,
+ pmu0_8_grp, pmu0_9_grp, pmu0_10_grp,
+ pmu0_11_grp, pcie0_0_grp, pcie0_1_grp,
+ pcie0_2_grp, pcie0_3_grp, pcie0_4_grp,
+ pcie0_5_grp, pcie0_6_grp, pcie0_7_grp,
+ csu0_0_grp, csu0_1_grp, csu0_2_grp,
+ csu0_3_grp, csu0_4_grp, csu0_5_grp,
+ csu0_6_grp, csu0_7_grp, csu0_8_grp,
+ csu0_9_grp, csu0_10_grp, csu0_11_grp,
+ dpaux0_0_grp, dpaux0_1_grp, dpaux0_2_grp,
+ dpaux0_3_grp, pjtag0_0_grp, pjtag0_1_grp,
+ pjtag0_2_grp, pjtag0_3_grp, pjtag0_4_grp,
+ pjtag0_5_grp, trace0_0_grp, trace0_clk_0_grp,
+ trace0_1_grp, trace0_clk_1_grp, trace0_2_grp,
+ trace0_clk_2_grp, testscan0_0_grp
+
+ Valid values for pins are:
+   MIO0 - MIO77
+
+ Valid values for function are:
+   ethernet0, ethernet1, ethernet2, ethernet3, gemtsu0, usb0, usb1, mdio0,
+   mdio1, mdio2, mdio3, qspi0, qspi_fbclk, qspi_ss, spi0, spi1, spi0_ss,
+   spi1_ss, sdio0, sdio0_pc, sdio0_wp, sdio0_cd, sdio1, sdio1_pc, sdio1_wp,
+   sdio1_cd, nand0, nand0_ce, nand0_rb, nand0_dqs, can0, can1, uart0, uart1,
+   i2c0, i2c1, ttc0_clk, ttc0_wav, ttc1_clk, ttc1_wav, ttc2_clk, ttc2_wav,
+   ttc3_clk, ttc3_wav, swdt0_clk, swdt0_rst, swdt1_clk, swdt1_rst, gpio0, pmu0,
+   pcie0, csu0, dpaux0, pjtag0, trace0, trace0_clk, testscan0
+
+The following driver-specific properties as defined here are valid to specify in
+a pin configuration subnode:
+ - io-standard: Configure the pin to use the selected IO standard. Valid
+   arguments are 'IO_STANDARD_LVCMOS33' and 'IO_STANDARD_LVCMOS18'.
+ - schmitt-cmos: Selects either Schmitt or CMOS input for MIO pins. Valid
+   arguments are 'PIN_INPUT_TYPE_SCHMITT' and 'PIN_INPUT_TYPE_CMOS'.
+
+Example:
+
+firmware {
+	zynqmp_firmware: zynqmp-firmware {
+		compatible = "xlnx,zynqmp-firmware";
+		method = "smc";
+
+		pinctrl0: pinctrl@ff180000 {
+			compatible = "xlnx,zynqmp-pinctrl";
+
+			pinctrl_uart1_default: uart1-default {
+				mux {
+					groups = "uart0_4_grp";
+					function = "uart0";
+				};
+
+				conf {
+					groups = "uart0_4_grp";
+					slew-rate = <SLEW_RATE_SLOW>;
+					io-standard = <IO_STANDARD_LVCMOS18>;
+				};
+
+				conf-rx {
+					pins = "MIO18";
+					bias-high-impedance;
+				};
+
+				conf-tx {
+					pins = "MIO19";
+					bias-disable;
+					schmitt-cmos = <PIN_INPUT_TYPE_CMOS>;
+				};
+			};
+		};
+	};
+};
+
+uart1 {
+	...
+        pinctrl-names = "default";
+        pinctrl-0 = <&pinctrl_uart1_default>;
+	...
+
+};
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 4/4] dt-bindings: pinctrl: Add ZynqMP pin controller bindings

[Rob Herring]

On Fri, Jan 04, 2019 at 01:56:22PM -0800, Jolly Shah wrote:
> From: Rajan Vaja <rajan.vaja@xilinx.com>
> 
> Add documentation to describe Xilinx ZynqMP pin controller
> bindings.
> 
> Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
> Signed-off-by: Jolly Shah <jollys@xilinx.com>
> ---
>  .../bindings/pinctrl/xlnx,zynqmp-pinctrl.txt       | 275 +++++++++++++++++++++
>  1 file changed, 275 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/pinctrl/xlnx,zynqmp-pinctrl.txt
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/xlnx,zynqmp-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/xlnx,zynqmp-pinctrl.txt
> new file mode 100644
> index 0000000..acf44a5
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/xlnx,zynqmp-pinctrl.txt
> @@ -0,0 +1,275 @@
> +	Binding for Xilinx ZynqMP Pinctrl
> +
> +Required properties:
> +- compatible: "xlnx,zynqmp-pinctrl"
> +
> +Please refer to pinctrl-bindings.txt in this directory for details of the
> +common pinctrl bindings used by client devices, including the meaning of the
> +phrase "pin configuration node".
> +
> +ZynqMP's pin configuration nodes act as a container for an arbitrary number of
> +subnodes. Each of these subnodes represents some desired configuration for a
> +pin, a group, or a list of pins or groups. This configuration can include the
> +mux function to select on those pin(s)/group(s), and various pin configuration
> +parameters, such as pull-up, slew rate, etc.
> +
> +Each configuration node can consist of multiple nodes describing the pinmux and
> +pinconf options. Those nodes can be pinmux nodes or pinconf nodes.
> +
> +The name of each subnode is not important; all subnodes should be enumerated
> +and processed purely based on their content.
> +
> +Required properties for pinmux nodes are:
> + - groups: A list of pinmux groups.
> + - function: The name of a pinmux function to activate for the specified set
> +   of groups.
> +
> +Required properties for configuration nodes:
> +One of:
> + - pins: A list of pin names
> + - groups: A list of pinmux groups.
> +
> +The following generic properties as defined in pinctrl-bindings.txt are valid
> +to specify in a pinmux subnode:
> + groups, function
> +
> +The following generic properties as defined in pinctrl-bindings.txt are valid
> +to specify in a pinconf subnode:
> + groups, pins, bias-disable, bias-pull-up, bias-pull-down, slew-rate
> +
> + Valid arguments for 'slew-rate' are 'SLEW_RATE_SLOW' and 'SLEW_RATE_FAST' to
> + select between slow and fast respectively.
> +
> + Valid values for groups are:
> + ethernet0_0_grp, ethernet1_0_grp, ethernet2_0_grp,
> + ethernet3_0_grp, gemtsu0_0_grp, gemtsu0_1_grp,
> + gemtsu0_2_grp, mdio0_0_grp, mdio1_0_grp,
> + mdio1_1_grp, mdio2_0_grp, mdio3_0_grp,
> + qspi0_0_grp, qspi_ss_0_grp, qspi_fbclk_0_grp,
> + spi0_0_grp, spi0_ss_0_grp, spi0_ss_1_grp,
> + spi0_ss_2_grp, spi0_1_grp, spi0_ss_3_grp,
> + spi0_ss_4_grp, spi0_ss_5_grp, spi0_2_grp,
> + spi0_ss_6_grp, spi0_ss_7_grp, spi0_ss_8_grp,
> + spi0_3_grp, spi0_ss_9_grp, spi0_ss_10_grp,
> + spi0_ss_11_grp, spi0_4_grp, spi0_ss_12_grp,
> + spi0_ss_13_grp, spi0_ss_14_grp, spi0_5_grp,
> + spi0_ss_15_grp, spi0_ss_16_grp, spi0_ss_17_grp,
> + spi1_0_grp, spi1_ss_0_grp, spi1_ss_1_grp,
> + spi1_ss_2_grp, spi1_1_grp, spi1_ss_3_grp,
> + spi1_ss_4_grp, spi1_ss_5_grp, spi1_2_grp,
> + spi1_ss_6_grp, spi1_ss_7_grp, spi1_ss_8_grp,
> + spi1_3_grp, spi1_ss_9_grp, spi1_ss_10_grp,
> + spi1_ss_11_grp, spi1_4_grp, spi1_ss_12_grp,
> + spi1_ss_13_grp, spi1_ss_14_grp, spi1_5_grp,
> + spi1_ss_15_grp, spi1_ss_16_grp, spi1_ss_17_grp,
> + sdio0_0_grp, sdio0_1_grp, sdio0_2_grp,
> + sdio0_3_grp, sdio0_4_grp, sdio0_5_grp,
> + sdio0_6_grp, sdio0_7_grp, sdio0_8_grp,
> + sdio0_9_grp, sdio0_10_grp, sdio0_11_grp,
> + sdio0_12_grp, sdio0_13_grp, sdio0_14_grp,
> + sdio0_15_grp, sdio0_16_grp, sdio0_17_grp,
> + sdio0_18_grp, sdio0_19_grp, sdio0_20_grp,
> + sdio0_21_grp, sdio0_22_grp, sdio0_23_grp,
> + sdio0_24_grp, sdio0_25_grp, sdio0_26_grp,
> + sdio0_27_grp, sdio0_28_grp, sdio0_29_grp,
> + sdio0_30_grp, sdio0_31_grp, sdio0_32_grp,
> + sdio0_pc_0_grp, sdio0_cd_0_grp, sdio0_wp_0_grp,
> + sdio0_pc_1_grp, sdio0_cd_1_grp, sdio0_wp_1_grp,
> + sdio0_pc_2_grp, sdio0_cd_2_grp, sdio0_wp_2_grp,
> + sdio1_0_grp, sdio1_1_grp, sdio1_2_grp,
> + sdio1_3_grp, sdio1_4_grp, sdio1_5_grp,
> + sdio1_6_grp, sdio1_7_grp, sdio1_8_grp,
> + sdio1_9_grp, sdio1_10_grp, sdio1_11_grp,
> + sdio1_12_grp, sdio1_13_grp, sdio1_14_grp,
> + sdio1_15_grp, sdio1_pc_0_grp, sdio1_cd_0_grp,
> + sdio1_wp_0_grp, sdio1_pc_1_grp, sdio1_cd_1_grp,
> + sdio1_wp_1_grp, nand0_0_grp, nand0_ce_0_grp,
> + nand0_rb_0_grp, nand0_dqs_0_grp, nand0_ce_1_grp,
> + nand0_rb_1_grp, nand0_dqs_1_grp, can0_0_grp,
> + can0_1_grp, can0_2_grp, can0_3_grp,
> + can0_4_grp, can0_5_grp, can0_6_grp,
> + can0_7_grp, can0_8_grp, can0_9_grp,
> + can0_10_grp, can0_11_grp, can0_12_grp,
> + can0_13_grp, can0_14_grp, can0_15_grp,
> + can0_16_grp, can0_17_grp, can0_18_grp,
> + can1_0_grp, can1_1_grp, can1_2_grp,
> + can1_3_grp, can1_4_grp, can1_5_grp,
> + can1_6_grp, can1_7_grp, can1_8_grp,
> + can1_9_grp, can1_10_grp, can1_11_grp,
> + can1_12_grp, can1_13_grp, can1_14_grp,
> + can1_15_grp, can1_16_grp, can1_17_grp,
> + can1_18_grp, can1_19_grp, uart0_0_grp,
> + uart0_1_grp, uart0_2_grp, uart0_3_grp,
> + uart0_4_grp, uart0_5_grp, uart0_6_grp,
> + uart0_7_grp, uart0_8_grp, uart0_9_grp,
> + uart0_10_grp, uart0_11_grp, uart0_12_grp,
> + uart0_13_grp, uart0_14_grp, uart0_15_grp,
> + uart0_16_grp, uart0_17_grp, uart0_18_grp,
> + uart1_0_grp, uart1_1_grp, uart1_2_grp,
> + uart1_3_grp, uart1_4_grp, uart1_5_grp,
> + uart1_6_grp, uart1_7_grp, uart1_8_grp,
> + uart1_9_grp, uart1_10_grp, uart1_11_grp,
> + uart1_12_grp, uart1_13_grp, uart1_14_grp,
> + uart1_15_grp, uart1_16_grp, uart1_17_grp,
> + uart1_18_grp, i2c0_0_grp, i2c0_1_grp,
> + i2c0_2_grp, i2c0_3_grp, i2c0_4_grp,
> + i2c0_5_grp, i2c0_6_grp, i2c0_7_grp,
> + i2c0_8_grp, i2c0_9_grp, i2c0_10_grp,
> + i2c0_11_grp, i2c0_12_grp, i2c0_13_grp,
> + i2c0_14_grp, i2c0_15_grp, i2c0_16_grp,
> + i2c0_17_grp, i2c0_18_grp, i2c1_0_grp,
> + i2c1_1_grp, i2c1_2_grp, i2c1_3_grp,
> + i2c1_4_grp, i2c1_5_grp, i2c1_6_grp,
> + i2c1_7_grp, i2c1_8_grp, i2c1_9_grp,
> + i2c1_10_grp, i2c1_11_grp, i2c1_12_grp,
> + i2c1_13_grp, i2c1_14_grp, i2c1_15_grp,
> + i2c1_16_grp, i2c1_17_grp, i2c1_18_grp,
> + i2c1_19_grp, ttc0_clk_0_grp, ttc0_wav_0_grp,
> + ttc0_clk_1_grp, ttc0_wav_1_grp, ttc0_clk_2_grp,
> + ttc0_wav_2_grp, ttc0_clk_3_grp, ttc0_wav_3_grp,
> + ttc0_clk_4_grp, ttc0_wav_4_grp, ttc0_clk_5_grp,
> + ttc0_wav_5_grp, ttc0_clk_6_grp, ttc0_wav_6_grp,
> + ttc0_clk_7_grp, ttc0_wav_7_grp, ttc0_clk_8_grp,
> + ttc0_wav_8_grp, ttc1_clk_0_grp, ttc1_wav_0_grp,
> + ttc1_clk_1_grp, ttc1_wav_1_grp, ttc1_clk_2_grp,
> + ttc1_wav_2_grp, ttc1_clk_3_grp, ttc1_wav_3_grp,
> + ttc1_clk_4_grp, ttc1_wav_4_grp, ttc1_clk_5_grp,
> + ttc1_wav_5_grp, ttc1_clk_6_grp, ttc1_wav_6_grp,
> + ttc1_clk_7_grp, ttc1_wav_7_grp, ttc1_clk_8_grp,
> + ttc1_wav_8_grp, ttc2_clk_0_grp, ttc2_wav_0_grp,
> + ttc2_clk_1_grp, ttc2_wav_1_grp, ttc2_clk_2_grp,
> + ttc2_wav_2_grp, ttc2_clk_3_grp, ttc2_wav_3_grp,
> + ttc2_clk_4_grp, ttc2_wav_4_grp, ttc2_clk_5_grp,
> + ttc2_wav_5_grp, ttc2_clk_6_grp, ttc2_wav_6_grp,
> + ttc2_clk_7_grp, ttc2_wav_7_grp, ttc2_clk_8_grp,
> + ttc2_wav_8_grp, ttc3_clk_0_grp, ttc3_wav_0_grp,
> + ttc3_clk_1_grp, ttc3_wav_1_grp, ttc3_clk_2_grp,
> + ttc3_wav_2_grp, ttc3_clk_3_grp, ttc3_wav_3_grp,
> + ttc3_clk_4_grp, ttc3_wav_4_grp, ttc3_clk_5_grp,
> + ttc3_wav_5_grp, ttc3_clk_6_grp, ttc3_wav_6_grp,
> + ttc3_clk_7_grp, ttc3_wav_7_grp, ttc3_clk_8_grp,
> + ttc3_wav_8_grp, swdt0_clk_0_grp, swdt0_rst_0_grp,
> + swdt0_clk_1_grp, swdt0_rst_1_grp, swdt0_clk_2_grp,
> + swdt0_rst_2_grp, swdt0_clk_3_grp, swdt0_rst_3_grp,
> + swdt0_clk_4_grp, swdt0_rst_4_grp, swdt0_clk_5_grp,
> + swdt0_rst_5_grp, swdt0_clk_6_grp, swdt0_rst_6_grp,
> + swdt0_clk_7_grp, swdt0_rst_7_grp, swdt0_clk_8_grp,
> + swdt0_rst_8_grp, swdt0_clk_9_grp, swdt0_rst_9_grp,
> + swdt0_clk_10_grp, swdt0_rst_10_grp, swdt0_clk_11_grp,
> + swdt0_rst_11_grp, swdt0_clk_12_grp, swdt0_rst_12_grp,
> + swdt1_clk_0_grp, swdt1_rst_0_grp, swdt1_clk_1_grp,
> + swdt1_rst_1_grp, swdt1_clk_2_grp, swdt1_rst_2_grp,
> + swdt1_clk_3_grp, swdt1_rst_3_grp, swdt1_clk_4_grp,
> + swdt1_rst_4_grp, swdt1_clk_5_grp, swdt1_rst_5_grp,
> + swdt1_clk_6_grp, swdt1_rst_6_grp, swdt1_clk_7_grp,
> + swdt1_rst_7_grp, swdt1_clk_8_grp, swdt1_rst_8_grp,
> + swdt1_clk_9_grp, swdt1_rst_9_grp, swdt1_clk_10_grp,
> + swdt1_rst_10_grp, swdt1_clk_11_grp, swdt1_rst_11_grp,
> + swdt1_clk_12_grp, swdt1_rst_12_grp, gpio0_0_grp,
> + gpio0_1_grp, gpio0_2_grp, gpio0_3_grp,
> + gpio0_4_grp, gpio0_5_grp, gpio0_6_grp,
> + gpio0_7_grp, gpio0_8_grp, gpio0_9_grp,
> + gpio0_10_grp, gpio0_11_grp, gpio0_12_grp,
> + gpio0_13_grp, gpio0_14_grp, gpio0_15_grp,
> + gpio0_16_grp, gpio0_17_grp, gpio0_18_grp,
> + gpio0_19_grp, gpio0_20_grp, gpio0_21_grp,
> + gpio0_22_grp, gpio0_23_grp, gpio0_24_grp,
> + gpio0_25_grp, gpio0_26_grp, gpio0_27_grp,
> + gpio0_28_grp, gpio0_29_grp, gpio0_30_grp,
> + gpio0_31_grp, gpio0_32_grp, gpio0_33_grp,
> + gpio0_34_grp, gpio0_35_grp, gpio0_36_grp,
> + gpio0_37_grp, gpio0_38_grp, gpio0_39_grp,
> + gpio0_40_grp, gpio0_41_grp, gpio0_42_grp,
> + gpio0_43_grp, gpio0_44_grp, gpio0_45_grp,
> + gpio0_46_grp, gpio0_47_grp, gpio0_48_grp,
> + gpio0_49_grp, gpio0_50_grp, gpio0_51_grp,
> + gpio0_52_grp, gpio0_53_grp, gpio0_54_grp,
> + gpio0_55_grp, gpio0_56_grp, gpio0_57_grp,
> + gpio0_58_grp, gpio0_59_grp, gpio0_60_grp,
> + gpio0_61_grp, gpio0_62_grp, gpio0_63_grp,
> + gpio0_64_grp, gpio0_65_grp, gpio0_66_grp,
> + gpio0_67_grp, gpio0_68_grp, gpio0_69_grp,
> + gpio0_70_grp, gpio0_71_grp, gpio0_72_grp,
> + gpio0_73_grp, gpio0_74_grp, gpio0_75_grp,
> + gpio0_76_grp, gpio0_77_grp, usb0_0_grp,
> + usb1_0_grp, pmu0_0_grp, pmu0_1_grp,
> + pmu0_2_grp, pmu0_3_grp, pmu0_4_grp,
> + pmu0_5_grp, pmu0_6_grp, pmu0_7_grp,
> + pmu0_8_grp, pmu0_9_grp, pmu0_10_grp,
> + pmu0_11_grp, pcie0_0_grp, pcie0_1_grp,
> + pcie0_2_grp, pcie0_3_grp, pcie0_4_grp,
> + pcie0_5_grp, pcie0_6_grp, pcie0_7_grp,
> + csu0_0_grp, csu0_1_grp, csu0_2_grp,
> + csu0_3_grp, csu0_4_grp, csu0_5_grp,
> + csu0_6_grp, csu0_7_grp, csu0_8_grp,
> + csu0_9_grp, csu0_10_grp, csu0_11_grp,
> + dpaux0_0_grp, dpaux0_1_grp, dpaux0_2_grp,
> + dpaux0_3_grp, pjtag0_0_grp, pjtag0_1_grp,
> + pjtag0_2_grp, pjtag0_3_grp, pjtag0_4_grp,
> + pjtag0_5_grp, trace0_0_grp, trace0_clk_0_grp,
> + trace0_1_grp, trace0_clk_1_grp, trace0_2_grp,
> + trace0_clk_2_grp, testscan0_0_grp
> +
> + Valid values for pins are:
> +   MIO0 - MIO77
> +
> + Valid values for function are:
> +   ethernet0, ethernet1, ethernet2, ethernet3, gemtsu0, usb0, usb1, mdio0,
> +   mdio1, mdio2, mdio3, qspi0, qspi_fbclk, qspi_ss, spi0, spi1, spi0_ss,
> +   spi1_ss, sdio0, sdio0_pc, sdio0_wp, sdio0_cd, sdio1, sdio1_pc, sdio1_wp,
> +   sdio1_cd, nand0, nand0_ce, nand0_rb, nand0_dqs, can0, can1, uart0, uart1,
> +   i2c0, i2c1, ttc0_clk, ttc0_wav, ttc1_clk, ttc1_wav, ttc2_clk, ttc2_wav,
> +   ttc3_clk, ttc3_wav, swdt0_clk, swdt0_rst, swdt1_clk, swdt1_rst, gpio0, pmu0,
> +   pcie0, csu0, dpaux0, pjtag0, trace0, trace0_clk, testscan0
> +
> +The following driver-specific properties as defined here are valid to specify in
> +a pin configuration subnode:
> + - io-standard: Configure the pin to use the selected IO standard. Valid
> +   arguments are 'IO_STANDARD_LVCMOS33' and 'IO_STANDARD_LVCMOS18'.
> + - schmitt-cmos: Selects either Schmitt or CMOS input for MIO pins. Valid
> +   arguments are 'PIN_INPUT_TYPE_SCHMITT' and 'PIN_INPUT_TYPE_CMOS'.
> +
> +Example:
> +
> +firmware {
> +	zynqmp_firmware: zynqmp-firmware {
> +		compatible = "xlnx,zynqmp-firmware";
> +		method = "smc";
> +
> +		pinctrl0: pinctrl@ff180000 {

The address here should be dropped.

Otherwise, looks fine.

Reviewed-by: Rob Herring <robh@kernel.org>

> +			compatible = "xlnx,zynqmp-pinctrl";
> +
> +			pinctrl_uart1_default: uart1-default {
> +				mux {
> +					groups = "uart0_4_grp";
> +					function = "uart0";
> +				};
> +
> +				conf {
> +					groups = "uart0_4_grp";
> +					slew-rate = <SLEW_RATE_SLOW>;
> +					io-standard = <IO_STANDARD_LVCMOS18>;
> +				};
> +
> +				conf-rx {
> +					pins = "MIO18";
> +					bias-high-impedance;
> +				};
> +
> +				conf-tx {
> +					pins = "MIO19";
> +					bias-disable;
> +					schmitt-cmos = <PIN_INPUT_TYPE_CMOS>;
> +				};
> +			};
> +		};
> +	};
> +};
> +
> +uart1 {
> +	...
> +        pinctrl-names = "default";
> +        pinctrl-0 = <&pinctrl_uart1_default>;
> +	...
> +
> +};
> -- 
> 2.7.4
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel