From: Maxime Chevallier <maxime.chevallier@bootlin.com>
To: davem@davemloft.net
Cc: Andrew Lunn <andrew@lunn.ch>,
Florian Fainelli <f.fainelli@gmail.com>,
mw@semihalf.com, Antoine Tenart <antoine.tenart@bootlin.com>,
netdev@vger.kernel.org, gregory.clement@bootlin.com,
linux-kernel@vger.kernel.org,
Maxime Chevallier <maxime.chevallier@bootlin.com>,
nadavh@marvell.com, thomas.petazzoni@bootlin.com,
miquel.raynal@bootlin.com, Russell King <linux@armlinux.org.uk>,
stefanc@marvell.com, linux-arm-kernel@lists.infradead.org,
Heiner Kallweit <hkallweit1@gmail.com>
Subject: [PATCH net-next 7/7] net: phy: marvell10g: add support for the 88x2110 PHY
Date: Thu, 21 Feb 2019 10:51:28 +0100 [thread overview]
Message-ID: <20190221095128.28188-8-maxime.chevallier@bootlin.com> (raw)
In-Reply-To: <20190221095128.28188-1-maxime.chevallier@bootlin.com>
This patch adds support for the 88x2110 PHY, which is similar to the
already supported 88x3310 PHY without the SFP interface.
It supports 10/100/1000BASET along with 2.5GBASET, 5GBASET and 10GBASET,
with the same interface modes that are used by the 3310.
This PHY don't have the same issue as the 88x3310 regarding 2.5/5G
abilities, and correctly follows the 802.3bz standard to list the
supported abilities.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Suggested-by: Antoine Tenart <antoine.tenart@bootlin.com>
---
drivers/net/phy/marvell10g.c | 13 +++++++++++++
include/linux/marvell_phy.h | 1 +
2 files changed, 14 insertions(+)
diff --git a/drivers/net/phy/marvell10g.c b/drivers/net/phy/marvell10g.c
index c48669d50653..bac199b7540f 100644
--- a/drivers/net/phy/marvell10g.c
+++ b/drivers/net/phy/marvell10g.c
@@ -490,12 +490,25 @@ static struct phy_driver mv3310_drivers[] = {
.aneg_done = mv3310_aneg_done,
.read_status = mv3310_read_status,
},
+ {
+ .phy_id = MARVELL_PHY_ID_88E2110,
+ .phy_id_mask = MARVELL_PHY_ID_MASK,
+ .name = "mv88x2110",
+ .features = PHY_10GBIT_FEATURES,
+ .probe = mv3310_probe,
+ .soft_reset = gen10g_no_soft_reset,
+ .config_init = mv3310_config_init,
+ .config_aneg = mv3310_config_aneg,
+ .aneg_done = mv3310_aneg_done,
+ .read_status = mv3310_read_status,
+ },
};
module_phy_driver(mv3310_drivers);
static struct mdio_device_id __maybe_unused mv3310_tbl[] = {
{ MARVELL_PHY_ID_88X3310, MARVELL_PHY_ID_MASK },
+ { MARVELL_PHY_ID_88E2110, MARVELL_PHY_ID_MASK },
{ },
};
MODULE_DEVICE_TABLE(mdio, mv3310_tbl);
diff --git a/include/linux/marvell_phy.h b/include/linux/marvell_phy.h
index 70c17345e118..73d04743a2bb 100644
--- a/include/linux/marvell_phy.h
+++ b/include/linux/marvell_phy.h
@@ -21,6 +21,7 @@
#define MARVELL_PHY_ID_88E1545 0x01410ea0
#define MARVELL_PHY_ID_88E3016 0x01410e60
#define MARVELL_PHY_ID_88X3310 0x002b09a0
+#define MARVELL_PHY_ID_88E2110 0x002b09b0
/* The MV88e6390 Ethernet switch contains embedded PHYs. These PHYs do
* not have a model ID. So the switch driver traps reads to the ID2
--
2.19.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2019-02-21 9:53 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-02-21 9:51 [PATCH net-next 0/7] net: phy: marvell10g: Add 2.5GBaseT Maxime Chevallier
2019-02-21 9:51 ` [PATCH net-next 1/7] net: phy: marvell10g: Use get_features to get the PHY abilities Maxime Chevallier
2019-02-21 10:22 ` Russell King - ARM Linux admin
2019-02-21 10:31 ` Maxime Chevallier
2019-02-22 18:42 ` Heiner Kallweit
2019-02-22 20:45 ` Maxime Chevallier
2019-02-21 9:51 ` [PATCH net-next 2/7] net: phy: marvell10g: Use linkmode_set_bit helper instead of __set_bit Maxime Chevallier
2019-02-21 9:51 ` [PATCH net-next 3/7] net: phy: marvell10g: Use 2500BASEX when using 2.5GBASET Maxime Chevallier
2019-02-21 9:51 ` [PATCH net-next 4/7] net: phy: marvell10g: Use a #define for 88X3310 family id Maxime Chevallier
2019-02-21 9:51 ` [PATCH net-next 5/7] net: phy: marvell10g: Force reading of 2.5/5G Maxime Chevallier
2019-02-21 9:51 ` [PATCH net-next 6/7] net: mvpp2: Add 2.5GBaseT support Maxime Chevallier
2019-02-21 9:51 ` Maxime Chevallier [this message]
-- strict thread matches above, loose matches on Subject: below --
2019-01-18 15:23 [PATCH net-next 0/7] net: phy: Add support for 2.5GBASET PHYs Maxime Chevallier
2019-01-18 15:23 ` [PATCH net-next 7/7] net: phy: marvell10g: add support for the 88x2110 PHY Maxime Chevallier
2019-01-20 19:10 ` Andrew Lunn
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190221095128.28188-8-maxime.chevallier@bootlin.com \
--to=maxime.chevallier@bootlin.com \
--cc=andrew@lunn.ch \
--cc=antoine.tenart@bootlin.com \
--cc=davem@davemloft.net \
--cc=f.fainelli@gmail.com \
--cc=gregory.clement@bootlin.com \
--cc=hkallweit1@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=miquel.raynal@bootlin.com \
--cc=mw@semihalf.com \
--cc=nadavh@marvell.com \
--cc=netdev@vger.kernel.org \
--cc=stefanc@marvell.com \
--cc=thomas.petazzoni@bootlin.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).