On Fri, Mar 15, 2019 at 02:32:55PM +0100, Paul Kocialkowski wrote:
> Hi,
> 
> On Fri, 2019-03-15 at 18:38 +0530, Jagan Teki wrote:
> > Some display panels would come up with a non-DSI output which
> > can have an option to connect DSI interface by means of bridge
> > convertor.
> > 
> > This DSI to non-DSI bridge convertor would require a bridge
> > driver that would communicate the DSI controller for bridge
> > functionalities.
> > 
> > So, add support for bridge functionalities in Allwinner DSI
> > controller.
> 
> See a few comments below.
> 
> > Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> > ---
> >  drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c | 65 +++++++++++++++++++-------
> >  drivers/gpu/drm/sun4i/sun6i_mipi_dsi.h |  1 +
> >  2 files changed, 49 insertions(+), 17 deletions(-)
> > 
> > diff --git a/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c b/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c
> > index 0960b96b62cc..64d74313b842 100644
> > --- a/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c
> > +++ b/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c
> > @@ -781,6 +781,9 @@ static void sun6i_dsi_encoder_enable(struct drm_encoder *encoder)
> >  	if (!IS_ERR(dsi->panel))
> >  		drm_panel_prepare(dsi->panel);
> >  
> > +	if (!IS_ERR(dsi->bridge))
> > +		drm_bridge_pre_enable(dsi->bridge);
> > +
> >  	/*
> >  	 * FIXME: This should be moved after the switch to HS mode.
> >  	 *
> > @@ -796,6 +799,9 @@ static void sun6i_dsi_encoder_enable(struct drm_encoder *encoder)
> >  	if (!IS_ERR(dsi->panel))
> >  		drm_panel_enable(dsi->panel);
> >  
> > +	if (!IS_ERR(dsi->bridge))
> > +		drm_bridge_enable(dsi->bridge);
> > +
> >  	sun6i_dsi_start(dsi, DSI_START_HSC);
> >  
> >  	udelay(1000);
> > @@ -812,6 +818,9 @@ static void sun6i_dsi_encoder_disable(struct drm_encoder *encoder)
> >  	if (!IS_ERR(dsi->panel)) {
> >  		drm_panel_disable(dsi->panel);
> >  		drm_panel_unprepare(dsi->panel);
> > +	} else if (!IS_ERR(dsi->bridge)) {
> > +		drm_bridge_disable(dsi->bridge);
> > +		drm_bridge_post_disable(dsi->bridge);
> >  	}
> >  
> >  	phy_power_off(dsi->dphy);
> > @@ -973,11 +982,16 @@ static int sun6i_dsi_attach(struct mipi_dsi_host *host,
> >  	struct sun6i_dsi *dsi = host_to_sun6i_dsi(host);
> >  
> >  	dsi->device = device;
> > -	dsi->panel = of_drm_find_panel(device->dev.of_node);
> > -	if (IS_ERR(dsi->panel))
> > -		return PTR_ERR(dsi->panel);
> >  
> > -	dev_info(host->dev, "Attached device %s\n", device->name);
> > +	dsi->bridge = of_drm_find_bridge(device->dev.of_node);
> > +	if (!dsi->bridge) {
> 
> You are using IS_ERR to check that the bridge is alive in the changes
> above, but switch to checking that it's non-NULL at this point.
> 
> Are both guaranteed to be interchangeable?

They aren't. Any ERR_PTR will be !NULL

> > +		dsi->panel = of_drm_find_panel(device->dev.of_node);
> > +		if (IS_ERR(dsi->panel))
> > +			return PTR_ERR(dsi->panel);
> > +	}
> 
> You should probably use drm_of_find_panel_or_bridge instead of
> duplicating the logic here.

Or we can even use the drm_panel_bridge_add to simplify things.

Maxime

-- 
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com