Linux-ARM-Kernel Archive on lore.kernel.org
 help / color / Atom feed
From: Neil Armstrong <narmstrong@baylibre.com>
To: khilman@baylibre.com
Cc: linux-amlogic@lists.infradead.org, linux-kernel@vger.kernel.org,
	linux-arm-kernel@lists.infradead.org,
	Neil Armstrong <narmstrong@baylibre.com>
Subject: [PATCH v3 3/3] arm64: dts: meson: Add minimal support for Odroid-N2
Date: Tue, 21 May 2019 17:19:52 +0200
Message-ID: <20190521151952.2779-4-narmstrong@baylibre.com> (raw)
In-Reply-To: <20190521151952.2779-1-narmstrong@baylibre.com>

This patch adds basic support for :
- Amlogic G12B, which is very similar to G12A
- The HardKernel Odroid-N2 based on the S922X SoC

The Amlogic G12B SoC is very similar with the G12A SoC, sharing
most of the features and architecture, but with these differences :
- The first CPU cluster only has 2xCortex-A53 instead of 4
- G12B has a second cluster of 4xCortex-A73
- Both cluster can achieve 2GHz instead of 1,8GHz for G12A
- CPU Clock architecture is difference, thus needing a different
  compatible to handle this slight difference
- Supports a MIPI CSI input
- Embeds a Mali-G52 instead of a Mali-G31, but integration is the same

Actual support is done in the same way as for the GXM support, including
the G12A dtsi and redefining the CPU clusters.
Unlike GXM, the first cluster is different, thus needing to remove
the last 2 cpu nodes of the first cluster.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
Martin,

I added MMC, SDCard and Network support, so I removed your Reviewed-by.

Neil

 arch/arm64/boot/dts/amlogic/Makefile          |   1 +
 .../boot/dts/amlogic/meson-g12b-odroid-n2.dts | 286 ++++++++++++++++++
 arch/arm64/boot/dts/amlogic/meson-g12b.dtsi   |  82 +++++
 3 files changed, 369 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b.dtsi

diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index e129c03ced14..07b861fe5fa5 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -3,6 +3,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nanopi-k2.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nexbox-a95x.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-odroidc2.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts
new file mode 100644
index 000000000000..904a47b8a4e7
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts
@@ -0,0 +1,286 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include "meson-g12b.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+
+/ {
+	compatible = "hardkernel,odroid-n2", "amlogic,g12b";
+	model = "Hardkernel ODROID-N2";
+
+	aliases {
+		serial0 = &uart_AO;
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		blue {
+			label = "n2:blue";
+			gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	tflash_vdd: regulator-tflash_vdd {
+		compatible = "regulator-fixed";
+
+		regulator-name = "TFLASH_VDD";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&gpio_ao GPIOAO_8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	tf_io: gpio-regulator-tf_io {
+		compatible = "regulator-gpio";
+
+		regulator-name = "TF_IO";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>;
+		gpios-states = <0>;
+
+		states = <3300000 0
+			  1800000 1>;
+	};
+
+	flash_1v8: regulator-flash_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "FLASH_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_3v3>;
+		regulator-always-on;
+	};
+
+	main_12v: regulator-main_12v {
+		compatible = "regulator-fixed";
+		regulator-name = "12V";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+	};
+
+	vcc_5v: regulator-vcc_5v {
+		compatible = "regulator-fixed";
+		regulator-name = "5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	vcc_1v8: regulator-vcc_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_3v3>;
+		regulator-always-on;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+		/* FIXME: actually controlled by VDDCPU_B_EN */
+	};
+
+	hub_5v: regulator-hub_5v {
+		compatible = "regulator-fixed";
+		regulator-name = "HUB_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc_5v>;
+
+		gpio = <&gpio GPIOH_5 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	usb_pwr_en: regulator-usb_pwr_en {
+		compatible = "regulator-fixed";
+		regulator-name = "USB_PWR_EN";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&hub_5v>;
+
+		gpio = <&gpio GPIOH_6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vddao_1v8: regulator-vddao_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&main_12v>;
+		regulator-always-on;
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_tx_tmds_out>;
+			};
+		};
+	};
+};
+
+&cec_AO {
+	pinctrl-0 = <&cec_ao_a_h_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&cecb_AO {
+	pinctrl-0 = <&cec_ao_b_h_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&ext_mdio {
+	external_phy: ethernet-phy@0 {
+		/* Realtek RTL8211F (0x001cc916) */	
+		reg = <0>;
+		max-speed = <1000>;
+		eee-broken-1000t;
+	};
+};
+
+&ethmac {
+	pinctrl-0 = <&eth_pins>, <&eth_rgmii_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	phy-mode = "rgmii";
+	phy-handle = <&external_phy>;
+	amlogic,tx-delay-ns = <2>;
+};
+
+&gpio {
+	/*
+	 * WARNING: The USB Hub on the Odroid-N2 needs a reset signal
+	 * to be turned high in order to be detected by the USB Controller
+	 * This signal should be handled by a USB specific power sequence
+	 * in order to reset the Hub when USB bus is powered down.
+	 */
+	usb-hub {
+		gpio-hog;
+		gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "usb-hub-reset";
+	};
+};
+
+&hdmi_tx {
+	status = "okay";
+	pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+	pinctrl-names = "default";
+	hdmi-supply = <&vcc_5v>;
+};
+
+&hdmi_tx_tmds_port {
+	hdmi_tx_tmds_out: endpoint {
+		remote-endpoint = <&hdmi_connector_in>;
+	};
+};
+
+&ir {
+	status = "okay";
+	pinctrl-0 = <&remote_input_ao_pins>;
+	pinctrl-names = "default";
+};
+
+/* SD card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_c_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <50000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&tflash_vdd>;
+	vqmmc-supply = <&tf_io>;
+
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	max-frequency = <200000000>;
+	disable-wp;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&flash_1v8>;
+};
+
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&usb {
+	status = "okay";
+};
+
+&usb2_phy0 {
+	phy-supply = <&usb_pwr_en>;
+};
+
+&usb2_phy1 {
+	phy-supply = <&vcc_5v>;
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi
new file mode 100644
index 000000000000..0359539ba884
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi
@@ -0,0 +1,82 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#include "meson-g12a.dtsi"
+
+/ {
+	compatible = "amlogic,g12b";
+
+	cpus {
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+
+				core1 {
+					cpu = <&cpu1>;
+				};
+			};
+
+			cluster1 {
+				core0 {
+					cpu = <&cpu100>;
+				};
+
+				core1 {
+					cpu = <&cpu101>;
+				};
+
+				core2 {
+					cpu = <&cpu102>;
+				};
+
+				core3 {
+					cpu = <&cpu103>;
+				};
+			};
+		};
+
+		/delete-node/ cpu@2;
+		/delete-node/ cpu@3;
+
+		cpu100: cpu@100 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a73", "arm,armv8";
+			reg = <0x0 0x100>;
+			enable-method = "psci";
+			next-level-cache = <&l2>;
+		};
+
+		cpu101: cpu@101 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a73", "arm,armv8";
+			reg = <0x0 0x101>;
+			enable-method = "psci";
+			next-level-cache = <&l2>;
+		};
+
+		cpu102: cpu@102 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a73", "arm,armv8";
+			reg = <0x0 0x102>;
+			enable-method = "psci";
+			next-level-cache = <&l2>;
+		};
+
+		cpu103: cpu@103 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a73", "arm,armv8";
+			reg = <0x0 0x103>;
+			enable-method = "psci";
+			next-level-cache = <&l2>;
+		};
+	};
+};
+
+&clkc {
+	compatible = "amlogic,g12b-clkc";
+};
-- 
2.21.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

  parent reply index

Thread overview: 11+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-05-21 15:19 [PATCH v3 0/3] arm64: Add initial " Neil Armstrong
2019-05-21 15:19 ` [PATCH v3 1/3] dt-bindings: arm: amlogic: add G12B bindings Neil Armstrong
2019-05-21 17:27   ` Martin Blumenstingl
2019-05-21 15:19 ` [PATCH v3 2/3] dt-bindings: arm: amlogic: add Odroid-N2 binding Neil Armstrong
2019-05-21 15:26   ` Rob Herring
2019-05-21 17:26   ` Martin Blumenstingl
2019-05-21 15:19 ` Neil Armstrong [this message]
2019-05-21 16:11   ` [PATCH v3 3/3] arm64: dts: meson: Add minimal support for Odroid-N2 Robin Murphy
2019-05-22  7:59     ` Neil Armstrong
2019-05-21 18:01   ` Martin Blumenstingl
2019-05-22  8:19     ` Neil Armstrong

Reply instructions:

You may reply publically to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20190521151952.2779-4-narmstrong@baylibre.com \
    --to=narmstrong@baylibre.com \
    --cc=khilman@baylibre.com \
    --cc=linux-amlogic@lists.infradead.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-ARM-Kernel Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-arm-kernel/0 linux-arm-kernel/git/0.git
	git clone --mirror https://lore.kernel.org/linux-arm-kernel/1 linux-arm-kernel/git/1.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-arm-kernel linux-arm-kernel/ https://lore.kernel.org/linux-arm-kernel \
		linux-arm-kernel@lists.infradead.org infradead-linux-arm-kernel@archiver.kernel.org
	public-inbox-index linux-arm-kernel


Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.infradead.lists.linux-arm-kernel


AGPL code for this site: git clone https://public-inbox.org/ public-inbox