Linux-ARM-Kernel Archive on lore.kernel.org
 help / color / Atom feed
From: Peng Fan <peng.fan@nxp.com>
To: "srinivas.kandagatla@linaro.org" <srinivas.kandagatla@linaro.org>,
	"robh+dt@kernel.org" <robh+dt@kernel.org>,
	"shawnguo@kernel.org" <shawnguo@kernel.org>,
	"s.hauer@pengutronix.de" <s.hauer@pengutronix.de>,
	"festevam@gmail.com" <festevam@gmail.com>
Cc: "devicetree@vger.kernel.org" <devicetree@vger.kernel.org>,
	Peng Fan <peng.fan@nxp.com>,
	"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>,
	dl-linux-imx <linux-imx@nxp.com>,
	Pengutronix Kernel Team <kernel@pengutronix.de>,
	"van.freenix@gmail.com" <van.freenix@gmail.com>,
	"linux-arm-kernel@lists.infradead.org"
	<linux-arm-kernel@lists.infradead.org>
Subject: [PATCH V3 RESEND 2/4] nvmem: imx: add i.MX8 nvmem driver
Date: Wed, 22 May 2019 01:46:58 +0000
Message-ID: <20190522020040.30283-2-peng.fan@nxp.com> (raw)
In-Reply-To: <20190522020040.30283-1-peng.fan@nxp.com>

This patch adds i.MX8 nvmem ocotp driver to access fuse via
RPC to i.MX8 system controller.

Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---

V3:
 Use imx_sc_msg_misc_fuse_read for req/resp
 Drop uneccessary check
 Drop the unnecessary type conversion
 Minor fixes according to v2 comments

V2:
 Add "scu" or "SCU", Add imx_sc_misc_otp_fuse_read, minor fixes

 drivers/nvmem/Kconfig         |   7 ++
 drivers/nvmem/Makefile        |   2 +
 drivers/nvmem/imx-ocotp-scu.c | 161 ++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 170 insertions(+)
 create mode 100644 drivers/nvmem/imx-ocotp-scu.c

diff --git a/drivers/nvmem/Kconfig b/drivers/nvmem/Kconfig
index 530d570724c9..79afe44195a1 100644
--- a/drivers/nvmem/Kconfig
+++ b/drivers/nvmem/Kconfig
@@ -36,6 +36,13 @@ config NVMEM_IMX_OCOTP
 	  This driver can also be built as a module. If so, the module
 	  will be called nvmem-imx-ocotp.
 
+config NVMEM_IMX_OCOTP_SCU
+	tristate "i.MX8 SCU On-Chip OTP Controller support"
+	depends on IMX_SCU
+	help
+	  This is a driver for the SCU On-Chip OTP Controller (OCOTP)
+	  available on i.MX8 SoCs.
+
 config NVMEM_LPC18XX_EEPROM
 	tristate "NXP LPC18XX EEPROM Memory Support"
 	depends on ARCH_LPC18XX || COMPILE_TEST
diff --git a/drivers/nvmem/Makefile b/drivers/nvmem/Makefile
index 2ece8ffffdda..30d653d34e57 100644
--- a/drivers/nvmem/Makefile
+++ b/drivers/nvmem/Makefile
@@ -13,6 +13,8 @@ obj-$(CONFIG_NVMEM_IMX_IIM)	+= nvmem-imx-iim.o
 nvmem-imx-iim-y			:= imx-iim.o
 obj-$(CONFIG_NVMEM_IMX_OCOTP)	+= nvmem-imx-ocotp.o
 nvmem-imx-ocotp-y		:= imx-ocotp.o
+obj-$(CONFIG_NVMEM_IMX_OCOTP_SCU)	+= nvmem-imx-ocotp-scu.o
+nvmem-imx-ocotp-scu-y		:= imx-ocotp-scu.o
 obj-$(CONFIG_NVMEM_LPC18XX_EEPROM)	+= nvmem_lpc18xx_eeprom.o
 nvmem_lpc18xx_eeprom-y	:= lpc18xx_eeprom.o
 obj-$(CONFIG_NVMEM_LPC18XX_OTP)	+= nvmem_lpc18xx_otp.o
diff --git a/drivers/nvmem/imx-ocotp-scu.c b/drivers/nvmem/imx-ocotp-scu.c
new file mode 100644
index 000000000000..d9dc482ecb2f
--- /dev/null
+++ b/drivers/nvmem/imx-ocotp-scu.c
@@ -0,0 +1,161 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * i.MX8 OCOTP fusebox driver
+ *
+ * Copyright 2019 NXP
+ *
+ * Peng Fan <peng.fan@nxp.com>
+ */
+
+#include <linux/firmware/imx/sci.h>
+#include <linux/module.h>
+#include <linux/nvmem-provider.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+enum ocotp_devtype {
+	IMX8QXP,
+};
+
+struct ocotp_devtype_data {
+	int devtype;
+	int nregs;
+};
+
+struct ocotp_priv {
+	struct device *dev;
+	const struct ocotp_devtype_data *data;
+	struct imx_sc_ipc *nvmem_ipc;
+};
+
+struct imx_sc_msg_misc_fuse_read {
+	struct imx_sc_rpc_msg hdr;
+	u32 word;
+} __packed;
+
+static struct ocotp_devtype_data imx8qxp_data = {
+	.devtype = IMX8QXP,
+	.nregs = 800,
+};
+
+static int imx_sc_misc_otp_fuse_read(struct imx_sc_ipc *ipc, u32 word,
+				     u32 *val)
+{
+	struct imx_sc_msg_misc_fuse_read msg;
+	struct imx_sc_rpc_msg *hdr = &msg.hdr;
+	int ret;
+
+	hdr->ver = IMX_SC_RPC_VERSION;
+	hdr->svc = IMX_SC_RPC_SVC_MISC;
+	hdr->func = IMX_SC_MISC_FUNC_OTP_FUSE_READ;
+	hdr->size = 2;
+
+	msg.word = word;
+
+	ret = imx_scu_call_rpc(ipc, &msg, true);
+	if (ret)
+		return ret;
+
+	*val = msg.word;
+
+	return 0;
+}
+
+static int imx_scu_ocotp_read(void *context, unsigned int offset,
+			      void *val, size_t bytes)
+{
+	struct ocotp_priv *priv = context;
+	u32 count, index, num_bytes;
+	u32 *buf;
+	void *p;
+	int i, ret;
+
+	index = offset >> 2;
+	num_bytes = round_up((offset % 4) + bytes, 4);
+	count = num_bytes >> 2;
+
+	if (count > (priv->data->nregs - index))
+		count = priv->data->nregs - index;
+
+	p = kzalloc(num_bytes, GFP_KERNEL);
+	if (!p)
+		return -ENOMEM;
+
+	buf = p;
+
+	for (i = index; i < (index + count); i++) {
+		if (priv->data->devtype == IMX8QXP) {
+			if ((i > 271) && (i < 544)) {
+				*buf++ = 0;
+				continue;
+			}
+		}
+
+		ret = imx_sc_misc_otp_fuse_read(priv->nvmem_ipc, i, buf);
+		if (ret) {
+			kfree(p);
+			return ret;
+		}
+		buf++;
+	}
+
+	memcpy(val, (u8 *)p + offset % 4, bytes);
+
+	kfree(p);
+
+	return 0;
+}
+
+static struct nvmem_config imx_scu_ocotp_nvmem_config = {
+	.name = "imx-scu-ocotp",
+	.read_only = true,
+	.word_size = 4,
+	.stride = 1,
+	.owner = THIS_MODULE,
+	.reg_read = imx_scu_ocotp_read,
+};
+
+static const struct of_device_id imx_scu_ocotp_dt_ids[] = {
+	{ .compatible = "fsl,imx8qxp-scu-ocotp", (void *)&imx8qxp_data },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, imx_scu_ocotp_dt_ids);
+
+static int imx_scu_ocotp_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct ocotp_priv *priv;
+	struct nvmem_device *nvmem;
+	int ret;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	ret = imx_scu_get_handle(&priv->nvmem_ipc);
+	if (ret)
+		return ret;
+
+	priv->data = of_device_get_match_data(dev);
+	priv->dev = dev;
+	imx_scu_ocotp_nvmem_config.size = 4 * priv->data->nregs;
+	imx_scu_ocotp_nvmem_config.dev = dev;
+	imx_scu_ocotp_nvmem_config.priv = priv;
+	nvmem = devm_nvmem_register(dev, &imx_scu_ocotp_nvmem_config);
+
+	return PTR_ERR_OR_ZERO(nvmem);
+}
+
+static struct platform_driver imx_scu_ocotp_driver = {
+	.probe	= imx_scu_ocotp_probe,
+	.driver = {
+		.name	= "imx_scu_ocotp",
+		.of_match_table = imx_scu_ocotp_dt_ids,
+	},
+};
+module_platform_driver(imx_scu_ocotp_driver);
+
+MODULE_AUTHOR("Peng Fan <peng.fan@nxp.com>");
+MODULE_DESCRIPTION("i.MX8 SCU OCOTP fuse box driver");
+MODULE_LICENSE("GPL v2");
-- 
2.16.4

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

  reply index

Thread overview: 7+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-05-22  1:46 [PATCH V3 RESEND 1/4] dt-bindings: fsl: scu: add ocotp binding Peng Fan
2019-05-22  1:46 ` Peng Fan [this message]
2019-05-23  8:47   ` [PATCH V3 RESEND 2/4] nvmem: imx: add i.MX8 nvmem driver Srinivas Kandagatla
2019-05-22  1:47 ` [PATCH V3 RESEND 3/4] defconfig: arm64: enable i.MX8 SCU octop driver Peng Fan
2019-05-23 12:52   ` Shawn Guo
2019-05-24  6:48     ` Peng Fan
2019-05-22  1:47 ` [PATCH V3 RESEND 4/4] arm64: dts: imx: add i.MX8QXP ocotp support Peng Fan

Reply instructions:

You may reply publically to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20190522020040.30283-2-peng.fan@nxp.com \
    --to=peng.fan@nxp.com \
    --cc=devicetree@vger.kernel.org \
    --cc=festevam@gmail.com \
    --cc=kernel@pengutronix.de \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-imx@nxp.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=robh+dt@kernel.org \
    --cc=s.hauer@pengutronix.de \
    --cc=shawnguo@kernel.org \
    --cc=srinivas.kandagatla@linaro.org \
    --cc=van.freenix@gmail.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-ARM-Kernel Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-arm-kernel/0 linux-arm-kernel/git/0.git
	git clone --mirror https://lore.kernel.org/linux-arm-kernel/1 linux-arm-kernel/git/1.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-arm-kernel linux-arm-kernel/ https://lore.kernel.org/linux-arm-kernel \
		linux-arm-kernel@lists.infradead.org infradead-linux-arm-kernel@archiver.kernel.org
	public-inbox-index linux-arm-kernel


Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.infradead.lists.linux-arm-kernel


AGPL code for this site: git clone https://public-inbox.org/ public-inbox