Linux-ARM-Kernel Archive on lore.kernel.org
 help / Atom feed
* [PATCH v12 0/4] Add support for the Purism Librem5 devkit
@ 2019-05-14 13:28 Angus Ainslie (Purism)
  2019-05-14 13:28 ` [PATCH v12 1/4] MAINTAINERS: add an entry for for arm64 imx devicetrees Angus Ainslie (Purism)
                   ` (3 more replies)
  0 siblings, 4 replies; 9+ messages in thread
From: Angus Ainslie (Purism) @ 2019-05-14 13:28 UTC (permalink / raw)
  To: angus.ainslie
  Cc: Mark Rutland, devicetree, Fabio Estevam, Sascha Hauer,
	Angus Ainslie \(Purism\),
	linux-kernel, Li Yang, Rob Herring, NXP Linux Team,
	Pengutronix Kernel Team, Shawn Guo, linux-arm-kernel

The Librem5 devkit is based on the imx8mq from NXP. This is a default
devicetree to boot the board to a command prompt.

Changes since v11:

Added reviewed-by tags.
Fixed subject typo.

Changes since v10:

Moved MAINTAINERS entry to "ARM/FREESCALE IMX" section

Changes since v9:

Added a MAINTAINERS entry for arm64 imx devicetree files.

Changes since v8:

Fixed license comment.
Changed regulators to all lower case.
Changed clock frequency for NXP errata e7805.
Dropped blank line.

Changes since v7:

More regulators always on for USB.
Add vbus regulator.
Drop vbat regulator.
Replace legacy "gpio-key,wakeup" with "wakeup-source".
Add vbus-supply to get rid of warning
imx8mq-usb-phy 382f0040.usb-phy: 382f0040.usb-phy supply vbus not found,
using dummy regulator

Changes since v6:

Dropped unused regulators.
Fix regulator phandles case.
Dropped extra whitespace.

Changes since v5:

Added reviewed-by tags.
Moved USB port links to USB controller node.

Changes since v4:

Compiled against linux-next next-20190415.
Added imx8mq to the arm yaml file.
Re-arrange regulator nodes to drop undefined supplies.
Additional ordering for aesthetics.
Split some long lines.
Added lots of blank lines.
Moved pinctl muxes to where they are used.
Cleaned out reg defintions from regulator nodes.

Changes since v3:

Freshly sorted and pressed nodes.
Change the backlight to an interpolated scale.
Dropped i2c2.
Dropped devkit version number to match debian MR.

Changes since v2:

Fixed incorrect phy-supply for the fsl-fec.
Dropped unused regulator property.
Fixup Makefile for linux-next.

Changes since v1:

Dropped config file.
Updated the board compatible label.
Changed node names to follow naming conventions.
Added a more complete regulator hierachy.
Removed unused nodes.
Removed unknown devices.
Fixed comment style.
Dropped undocumented properties.

Angus Ainslie (Purism) (4):
  MAINTAINERS: add an entry for for arm64 imx devicetrees
  arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit
  dt-bindings: Add an entry for Purism SPC
  dt-bindings: arm: fsl: Add the imx8mq boards

 .../devicetree/bindings/arm/fsl.yaml          |   7 +
 .../devicetree/bindings/vendor-prefixes.txt   |   1 +
 MAINTAINERS                                   |   1 +
 arch/arm64/boot/dts/freescale/Makefile        |   1 +
 .../dts/freescale/imx8mq-librem5-devkit.dts   | 821 ++++++++++++++++++
 5 files changed, 831 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts

-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 9+ messages in thread

* [PATCH v12 1/4] MAINTAINERS: add an entry for for arm64 imx devicetrees
  2019-05-14 13:28 [PATCH v12 0/4] Add support for the Purism Librem5 devkit Angus Ainslie (Purism)
@ 2019-05-14 13:28 ` Angus Ainslie (Purism)
  2019-05-22  8:30   ` Shawn Guo
  2019-05-14 13:28 ` [PATCH v12 2/4] arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit Angus Ainslie (Purism)
                   ` (2 subsequent siblings)
  3 siblings, 1 reply; 9+ messages in thread
From: Angus Ainslie (Purism) @ 2019-05-14 13:28 UTC (permalink / raw)
  To: angus.ainslie
  Cc: Mark Rutland, devicetree, Fabio Estevam, Sascha Hauer,
	Angus Ainslie \(Purism\),
	linux-kernel, Li Yang, Rob Herring, NXP Linux Team,
	Pengutronix Kernel Team, Shawn Guo, linux-arm-kernel

Add an explicit reference to imx* devicetrees

Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
---
 MAINTAINERS | 1 +
 1 file changed, 1 insertion(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index 7707c28628b9..9fc30f82ab81 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1624,6 +1624,7 @@ R:	NXP Linux Team <linux-imx@nxp.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux.git
+F:	arch/arm64/boot/dts/freescale/imx*
 N:	imx
 N:	mxs
 X:	drivers/media/i2c/
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 9+ messages in thread

* [PATCH v12 2/4] arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit
  2019-05-14 13:28 [PATCH v12 0/4] Add support for the Purism Librem5 devkit Angus Ainslie (Purism)
  2019-05-14 13:28 ` [PATCH v12 1/4] MAINTAINERS: add an entry for for arm64 imx devicetrees Angus Ainslie (Purism)
@ 2019-05-14 13:28 ` Angus Ainslie (Purism)
  2019-05-22  8:57   ` Shawn Guo
  2019-05-14 13:28 ` [PATCH v12 3/4] dt-bindings: Add an entry for Purism SPC Angus Ainslie (Purism)
  2019-05-14 13:28 ` [PATCH v12 4/4] dt-bindings: arm: fsl: Add the imx8mq boards Angus Ainslie (Purism)
  3 siblings, 1 reply; 9+ messages in thread
From: Angus Ainslie (Purism) @ 2019-05-14 13:28 UTC (permalink / raw)
  To: angus.ainslie
  Cc: Mark Rutland, devicetree, Fabio Estevam, Sascha Hauer,
	Angus Ainslie \(Purism\),
	linux-kernel, Li Yang, Rob Herring, NXP Linux Team,
	Pengutronix Kernel Team, Shawn Guo, linux-arm-kernel

This is for the development kit board for the Librem 5. The current level
of support yields a working console and is able to boot userspace from
the network or eMMC.

Additional subsystems that are active :

- Both USB ports
- SD card socket
- WiFi usdhc
- WWAN modem
- GNSS
- GPIO keys
- LEDs
- gyro
- magnetometer
- touchscreen
- pwm
- backlight
- haptic motor

Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
---
 arch/arm64/boot/dts/freescale/Makefile        |   1 +
 .../dts/freescale/imx8mq-librem5-devkit.dts   | 821 ++++++++++++++++++
 2 files changed, 822 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 0bd122f60549..c043aca66572 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -22,6 +22,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
 
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-evk.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-rmb3.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-zest.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8qxp-mek.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
new file mode 100644
index 000000000000..64898daee644
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
@@ -0,0 +1,821 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2018-2019 Purism SPC
+ */
+
+/dts-v1/;
+
+#include "dt-bindings/input/input.h"
+#include "dt-bindings/usb/pd.h"
+#include "imx8mq.dtsi"
+
+/ {
+	model = "Purism Librem 5 devkit";
+	compatible = "purism,librem5-devkit", "fsl,imx8mq";
+
+	backlight_dsi: backlight-dsi {
+		compatible = "pwm-backlight";
+		/* 200 Hz for the PAM2841 */
+		pwms = <&pwm1 0 5000000>;
+		brightness-levels = <0 100>;
+		num-interpolated-steps = <100>;
+		/* Default brightness level (index into the array defined by */
+		/* the "brightness-levels" property) */
+		default-brightness-level = <0>;
+		power-supply = <&reg_22v4_p>;
+	};
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		btn1 {
+			label = "VOL_UP";
+			gpios = <&gpio4 21 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+
+		btn2 {
+			label = "VOL_DOWN";
+			gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+
+		hp_det {
+			label = "HP_DET";
+			gpios = <&gpio3 20 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+			linux,code = <KEY_HP>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_leds>;
+
+		led1 {
+			label = "LED 1";
+			gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	pmic_osc: pmic-osc {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "pmic_osc";
+	};
+
+	pwmleds {
+		compatible = "pwm-leds";
+
+		haptic {
+			label = "librem5::haptic";
+			pwms = <&pwm2 0 200000>;
+			active-low;
+			max-brightness = <255>;
+			power-supply = <&reg_3v3_p>;
+		};
+	};
+
+	reg_1v8_p: regulator-1v8-p {
+		compatible = "regulator-fixed";
+		regulator-name = "1v8_p";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&reg_pwr_en>;
+	};
+
+	reg_2v8_p: regulator-2v8-p {
+		compatible = "regulator-fixed";
+		regulator-name = "2v8_p";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		vin-supply = <&reg_pwr_en>;
+	};
+
+	reg_3v3_p: regulator-3v3-p {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3_p";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&reg_pwr_en>;
+		regulator-state-mem {
+			regulator-on-in-suspend;
+		};
+	};
+
+	reg_5v_p: regulator-5v-p {
+		compatible = "regulator-fixed";
+		regulator-name = "5v_p";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&reg_pwr_en>;
+		regulator-state-mem {
+			regulator-on-in-suspend;
+		};
+	};
+
+	reg_22v4_p: regulator-22v4-p {
+		compatible = "regulator-fixed";
+		regulator-name = "22v4_P";
+		regulator-min-microvolt = <22400000>;
+		regulator-max-microvolt = <22400000>;
+		vin-supply = <&reg_pwr_en>;
+	};
+
+	reg_pwr_en: regulator-pwr-en {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pwr_en>;
+		regulator-name = "PWR_EN";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	reg_usdhc2_vmmc: regulator-usdhc2-vmmc {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usdhc2_pwr>;
+		regulator-name = "VSD_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	wifi_pwr_en: wifi-en {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi_pwr_en>;
+		regulator-name = "WIFI_EN";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 5 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+};
+
+&clk {
+	assigned-clocks = <&clk IMX8MQ_AUDIO_PLL1>, <&clk IMX8MQ_AUDIO_PLL2>;
+	assigned-clock-rates = <786432000>, <722534400>;
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy0>;
+	fsl,magic-packet;
+	phy-supply = <&reg_3v3_p>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	pmic: pmic@4b {
+		compatible = "rohm,bd71837";
+		reg = <0x4b>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+		clocks = <&pmic_osc>;
+		clock-names = "osc";
+		clock-output-names = "pmic_clk";
+		interrupt-parent = <&gpio1>;
+		interrupts = <3 GPIO_ACTIVE_LOW>;
+		interrupt-names = "irq";
+		rohm,reset-snvs-powered;
+
+		regulators {
+
+			buck1_reg: BUCK1 {
+				regulator-name = "buck1";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <1250>;
+				rohm,dvs-run-voltage = <900000>;
+				rohm,dvs-idle-voltage = <850000>;
+				rohm,dvs-suspend-voltage = <800000>;
+			};
+
+			buck2_reg: BUCK2 {
+				regulator-name = "buck2";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <1250>;
+				rohm,dvs-run-voltage = <1000000>;
+				rohm,dvs-idle-voltage = <900000>;
+			};
+
+			buck3_reg: BUCK3 {
+				regulator-name = "buck3";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				rohm,dvs-run-voltage = <1000000>;
+			};
+
+			buck4_reg: BUCK4 {
+				regulator-name = "buck4";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				rohm,dvs-run-voltage = <1000000>;
+			};
+
+			buck5_reg: BUCK5 {
+				regulator-name = "buck5";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck6_reg: BUCK6 {
+				regulator-name = "buck6";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck7_reg: BUCK7 {
+				regulator-name = "buck7";
+				regulator-min-microvolt = <1605000>;
+				regulator-max-microvolt = <1995000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck8_reg: BUCK8 {
+				regulator-name = "buck8";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo1_reg: LDO1 {
+				regulator-name = "ldo1";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo2_reg: LDO2 {
+				regulator-name = "ldo2";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo3_reg: LDO3 {
+				regulator-name = "ldo3";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo4_reg: LDO4 {
+				regulator-name = "ldo4";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo5_reg: LDO5 {
+				regulator-name = "ldo5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			ldo6_reg: LDO6 {
+				regulator-name = "ldo6";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo7_reg: LDO7 {
+				regulator-name = "ldo7";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+
+	typec_ptn5100: usb_typec@52 {
+		compatible = "nxp,ptn5110";
+		reg = <0x52>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_typec>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+
+		connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			data-role = "dual";
+			power-role = "dual";
+			try-power-role = "sink";
+			source-pdos = <PDO_FIXED(5000, 2000,
+				PDO_FIXED_USB_COMM |
+				PDO_FIXED_DUAL_ROLE |
+				PDO_FIXED_DATA_SWAP )>;
+			sink-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM |
+				PDO_FIXED_DUAL_ROLE |
+				PDO_FIXED_DATA_SWAP )
+			     PDO_VAR(5000, 12000, 2000)>;
+			op-sink-microwatt = <10000000>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					usb_con_hs: endpoint {
+						remote-endpoint = <&typec_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					usb_con_ss: endpoint {
+						remote-endpoint = <&typec_ss>;
+					};
+				};
+			};
+		};
+	};
+
+	rtc@68 {
+		compatible = "microcrystal,rv4162";
+		reg = <0x68>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rtc>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	charger@6b { /* bq25896 */
+		compatible = "ti,bq25890";
+		reg = <0x6b>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_charger>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+		ti,battery-regulation-voltage = <4192000>; /* 4.192V */
+		ti,charge-current = <1600000>; /* 1.6 A */
+		ti,termination-current = <66000>;  /* 66mA */
+		ti,precharge-current = <1300000>; /* 1.3A */
+		ti,minimum-sys-voltage = <2750000>; /* 2.75V */
+		ti,boost-voltage = <5000000>; /* 5V */
+		ti,boost-max-current = <50000>; /* 50mA */
+	};
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	magnetometer@1e	{
+		compatible = "st,lsm9ds1-magn";
+		reg = <0x1e>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_imu>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
+		vdd-supply = <&reg_3v3_p>;
+		vddio-supply = <&reg_3v3_p>;
+	};
+
+	touchscreen@5d {
+		compatible = "goodix,gt5688";
+		reg = <0x5d>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_goodix_ts>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+		irq-gpios = <&gpio3 0 GPIO_ACTIVE_HIGH>;
+		touchscreen-size-x = <720>;
+		touchscreen-size-y = <1440>;
+		AVDD28-supply = <&reg_2v8_p>;
+		VDDIO-supply = <&reg_1v8_p>;
+	};
+};
+
+&iomuxc {
+	pinctrl_backlight: pwm1 {
+		fsl,pins = <
+		MX8MQ_IOMUXC_GPIO1_IO01_PWM1_OUT	0x6  /* DSI_BL_PWM */
+		>;
+	};
+
+	pinctrl_bt: btgrp {
+		fsl,pins = <
+		/* nBT_DISABLE */
+		MX8MQ_IOMUXC_NAND_DATA05_GPIO3_IO11             0x16
+		/* BT_HOST_WAKE */
+		MX8MQ_IOMUXC_NAND_DATA01_GPIO3_IO7              0x10
+		>;
+	};
+
+	pinctrl_charger: chargernirq {
+		fsl,pins = <
+		/* CHRG_nINT */
+		MX8MQ_IOMUXC_SAI5_MCLK_GPIO3_IO25	0x80
+		>;
+	};
+
+	pinctrl_fec1: fec1grp {
+		fsl,pins = <
+		MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC		0x3
+		MX8MQ_IOMUXC_ENET_MDIO_ENET1_MDIO	0x3
+		MX8MQ_IOMUXC_ENET_TD3_ENET1_RGMII_TD3	0x1f
+		MX8MQ_IOMUXC_ENET_TD2_ENET1_RGMII_TD2	0x1f
+		MX8MQ_IOMUXC_ENET_TD1_ENET1_RGMII_TD1	0x1f
+		MX8MQ_IOMUXC_ENET_TD0_ENET1_RGMII_TD0	0x1f
+		MX8MQ_IOMUXC_ENET_RD3_ENET1_RGMII_RD3	0x91
+		MX8MQ_IOMUXC_ENET_RD2_ENET1_RGMII_RD2	0x91
+		MX8MQ_IOMUXC_ENET_RD1_ENET1_RGMII_RD1	0x91
+		MX8MQ_IOMUXC_ENET_RD0_ENET1_RGMII_RD0	0x91
+		MX8MQ_IOMUXC_ENET_TXC_ENET1_RGMII_TXC	0x1f
+		MX8MQ_IOMUXC_ENET_RXC_ENET1_RGMII_RXC	0x91
+		MX8MQ_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91
+		MX8MQ_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f
+		MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9	0x19
+		MX8MQ_IOMUXC_GPIO1_IO15_CCMSRCGPCMIX_CLKO2      0x1f
+		>;
+	};
+
+	pinctrl_goodix_ts: gt5688 {
+		fsl,pins = <
+		/* TOUCH INT */
+		MX8MQ_IOMUXC_NAND_ALE_GPIO3_IO0         0x16
+		/* TOUCH RST */
+		MX8MQ_IOMUXC_GPIO1_IO05_GPIO1_IO5	0x19
+		>;
+	};
+
+	pinctrl_gpio_leds: gpioleds {
+		fsl,pins = <
+		MX8MQ_IOMUXC_GPIO1_IO13_GPIO1_IO13	0x16
+		>;
+	};
+
+	pinctrl_gpio_keys: gpiokeys {
+		fsl,pins = <
+		MX8MQ_IOMUXC_SAI2_RXFS_GPIO4_IO21	0x16
+		MX8MQ_IOMUXC_SAI2_RXC_GPIO4_IO22	0x16
+		/* HP_DET */
+		MX8MQ_IOMUXC_SAI5_RXC_GPIO3_IO20	0x180
+		>;
+	};
+
+	pinctrl_haptic: hapticgrp {
+		fsl,pins = <
+		MX8MQ_IOMUXC_SPDIF_RX_PWM2_OUT		0xc6  /* nHAPTIC */
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+		MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL		0x4000001f
+		MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA		0x4000001f
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+		MX8MQ_IOMUXC_I2C3_SCL_I2C3_SCL		0x4000001f
+		MX8MQ_IOMUXC_I2C3_SDA_I2C3_SDA		0x4000001f
+		>;
+	};
+
+	pinctrl_imu: imugrp {
+		fsl,pins = <
+		/* IMU_INT */
+		MX8MQ_IOMUXC_SAI5_RXFS_GPIO3_IO19	0x8
+		>;
+	};
+
+	pinctrl_pmic: pmicint {
+		fsl,pins = <
+		MX8MQ_IOMUXC_GPIO1_IO03_GPIO1_IO3	0x80
+		>;
+	};
+
+	pinctrl_pwr_en: pwrengrp {
+		fsl,pins = <
+		MX8MQ_IOMUXC_GPIO1_IO08_GPIO1_IO8               0x06
+		>;
+	};
+
+	pinctrl_rtc: rtcirq {
+		fsl,pins = <
+		MX8MQ_IOMUXC_SAI3_RXC_GPIO4_IO29	0x80
+		>;
+	};
+
+	pinctrl_typec: typecgrp {
+		fsl,pins = <
+		MX8MQ_IOMUXC_NAND_DATA06_GPIO3_IO12	0x16
+		MX8MQ_IOMUXC_NAND_CE0_B_GPIO3_IO1	0x80
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+		MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX		0x49
+		MX8MQ_IOMUXC_UART1_TXD_UART1_DCE_TX		0x49
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+		MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX		0x49
+		MX8MQ_IOMUXC_UART2_RXD_UART2_DCE_RX		0x49
+		MX8MQ_IOMUXC_UART4_RXD_UART2_DCE_CTS_B		0x49
+		MX8MQ_IOMUXC_UART4_TXD_UART2_DCE_RTS_B		0x49
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+		MX8MQ_IOMUXC_UART3_RXD_UART3_DCE_RX		0x49
+		MX8MQ_IOMUXC_UART3_TXD_UART3_DCE_TX		0x49
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+		MX8MQ_IOMUXC_ECSPI2_SCLK_UART4_DCE_RX		0x49
+		MX8MQ_IOMUXC_ECSPI2_MOSI_UART4_DCE_TX		0x49
+		MX8MQ_IOMUXC_ECSPI2_MISO_UART4_DCE_CTS_B	0x49
+		MX8MQ_IOMUXC_ECSPI2_SS0_UART4_DCE_RTS_B		0x49
+		MX8MQ_IOMUXC_GPIO1_IO00_ANAMIX_REF_CLK_32K	0x49
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+		MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK			0x83
+		MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD			0xc3
+		MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0		0xc3
+		MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1		0xc3
+		MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2		0xc3
+		MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3		0xc3
+		MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4		0xc3
+		MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5		0xc3
+		MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6		0xc3
+		MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7		0xc3
+		MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x83
+		MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B		0xc1
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+		fsl,pins = <
+		MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK			0x8d
+		MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD			0xcd
+		MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0		0xcd
+		MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1		0xcd
+		MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2		0xcd
+		MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3		0xcd
+		MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4		0xcd
+		MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5		0xcd
+		MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6		0xcd
+		MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7		0xcd
+		MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x8d
+		MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B		0xc1
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+		fsl,pins = <
+		MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK			0x9f
+		MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD			0xdf
+		MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0		0xdf
+		MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1		0xdf
+		MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2		0xdf
+		MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3		0xdf
+		MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4		0xdf
+		MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5		0xdf
+		MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6		0xdf
+		MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7		0xdf
+		MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x9f
+		MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B		0xc1
+		>;
+	};
+
+	pinctrl_usdhc2_pwr: usdhc2grppwr {
+		fsl,pins = <
+		MX8MQ_IOMUXC_SD2_RESET_B_GPIO2_IO19		0x41
+		>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2grpgpio {
+		fsl,pins = <
+		/* WIFI_WAKE */
+		MX8MQ_IOMUXC_SD2_WP_GPIO2_IO20			0x80
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+		MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK			0x83
+		MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD			0xc3
+		MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0		0xc3
+		MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1		0xc3
+		MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2		0xc3
+		MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3		0xc3
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+		fsl,pins = <
+		MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK			0x8d
+		MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD			0xcd
+		MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0		0xcd
+		MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1		0xcd
+		MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2		0xcd
+		MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3		0xcd
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+		fsl,pins = <
+		MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK			0x9f
+		MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD			0xcf
+		MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0		0xcf
+		MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1		0xcf
+		MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2		0xcf
+		MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3		0xcf
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+		MX8MQ_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B	0xc6
+		>;
+	};
+
+	pinctrl_wifi_pwr_en: wifipwrengrp {
+		fsl,pins = <
+		MX8MQ_IOMUXC_NAND_CLE_GPIO3_IO5         0x06
+		>;
+	};
+
+	pinctrl_wwan: wwangrp {
+		fsl,pins = <
+		/* nWWAN_DISABLE */
+		MX8MQ_IOMUXC_NAND_CE3_B_GPIO3_IO4	0x09
+		/* nWoWWAN */
+		MX8MQ_IOMUXC_NAND_DATA02_GPIO3_IO8	0x80
+		/* WWAN_RESET */
+		MX8MQ_IOMUXC_NAND_DATA03_GPIO3_IO9	0x19
+		>;
+	};
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_backlight>;
+	status = "okay";
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_haptic>;
+	status = "okay";
+};
+
+&uart1 { /* console */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart3 { /* GNSS */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&uart4 { /* BT */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>, <&pinctrl_bt>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usb3_phy0 {
+	status = "okay";
+};
+
+&usb3_phy1 {
+	vbus-supply = <&reg_5v_p>;
+	status = "okay";
+};
+
+&usb_dwc3_0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	dr_mode = "otg";
+	status = "okay";
+
+	port@0 {
+		reg = <0>;
+
+		typec_hs: endpoint {
+			remote-endpoint = <&usb_con_hs>;
+		};
+	};
+
+	port@1 {
+		reg = <1>;
+
+		typec_ss: endpoint {
+			remote-endpoint = <&usb_con_ss>;
+		};
+	};
+};
+
+&usb_dwc3_1 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	power-supply = <&wifi_pwr_en>;
+	non-removable;
+	disable-wp;
+	cap-sdio-irq;
+	keep-power-in-suspend;
+	wakeup-source;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 9+ messages in thread

* [PATCH v12 3/4] dt-bindings: Add an entry for Purism SPC
  2019-05-14 13:28 [PATCH v12 0/4] Add support for the Purism Librem5 devkit Angus Ainslie (Purism)
  2019-05-14 13:28 ` [PATCH v12 1/4] MAINTAINERS: add an entry for for arm64 imx devicetrees Angus Ainslie (Purism)
  2019-05-14 13:28 ` [PATCH v12 2/4] arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit Angus Ainslie (Purism)
@ 2019-05-14 13:28 ` Angus Ainslie (Purism)
  2019-05-17  2:31   ` Rob Herring
  2019-05-14 13:28 ` [PATCH v12 4/4] dt-bindings: arm: fsl: Add the imx8mq boards Angus Ainslie (Purism)
  3 siblings, 1 reply; 9+ messages in thread
From: Angus Ainslie (Purism) @ 2019-05-14 13:28 UTC (permalink / raw)
  To: angus.ainslie
  Cc: Mark Rutland, devicetree, Fabio Estevam, Sascha Hauer,
	Angus Ainslie \(Purism\),
	linux-kernel, Li Yang, Rob Herring, NXP Linux Team,
	Pengutronix Kernel Team, Shawn Guo, linux-arm-kernel

Add an entry for Purism, SPC

Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index e9034a6c003a..64bb1fa1a4d5 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -333,6 +333,7 @@ poslab	Poslab Technology Co., Ltd.
 powervr	PowerVR (deprecated, use img)
 probox2	PROBOX2 (by W2COMP Co., Ltd.)
 pulsedlight	PulsedLight, Inc
+purism	Purism, SPC
 qca	Qualcomm Atheros, Inc.
 qcom	Qualcomm Technologies, Inc
 qemu	QEMU, a generic and open source machine emulator and virtualizer
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 9+ messages in thread

* [PATCH v12 4/4] dt-bindings: arm: fsl: Add the imx8mq boards
  2019-05-14 13:28 [PATCH v12 0/4] Add support for the Purism Librem5 devkit Angus Ainslie (Purism)
                   ` (2 preceding siblings ...)
  2019-05-14 13:28 ` [PATCH v12 3/4] dt-bindings: Add an entry for Purism SPC Angus Ainslie (Purism)
@ 2019-05-14 13:28 ` Angus Ainslie (Purism)
  3 siblings, 0 replies; 9+ messages in thread
From: Angus Ainslie (Purism) @ 2019-05-14 13:28 UTC (permalink / raw)
  To: angus.ainslie
  Cc: Mark Rutland, devicetree, Fabio Estevam, Sascha Hauer,
	Angus Ainslie \(Purism\),
	linux-kernel, Li Yang, Rob Herring, NXP Linux Team,
	Pengutronix Kernel Team, Shawn Guo, linux-arm-kernel

Add an entry for imx8mq based boards

Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/arm/fsl.yaml | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 407138ebc0d0..41364b127200 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -177,6 +177,13 @@ properties:
               - fsl,imx8mm-evk            # i.MX8MM EVK Board
           - const: fsl,imx8mm
 
+      - description: i.MX8MQ based Boards
+        items:
+          - enum:
+              - fsl,imx8mq-evk            # i.MX8MQ EVK Board
+              - purism,librem5-devkit     # Purism Librem5 devkit
+          - const: fsl,imx8mq
+
       - description: i.MX8QXP based Boards
         items:
           - enum:
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 9+ messages in thread

* Re: [PATCH v12 3/4] dt-bindings: Add an entry for Purism SPC
  2019-05-14 13:28 ` [PATCH v12 3/4] dt-bindings: Add an entry for Purism SPC Angus Ainslie (Purism)
@ 2019-05-17  2:31   ` Rob Herring
  0 siblings, 0 replies; 9+ messages in thread
From: Rob Herring @ 2019-05-17  2:31 UTC (permalink / raw)
  To: Angus Ainslie (Purism)
  Cc: Mark Rutland, devicetree, Fabio Estevam, Sascha Hauer,
	linux-kernel, Li Yang, NXP Linux Team, Pengutronix Kernel Team,
	angus.ainslie, Shawn Guo,
	moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE

On Tue, May 14, 2019 at 8:28 AM Angus Ainslie (Purism) <angus@akkea.ca> wrote:
>
> Add an entry for Purism, SPC
>
> Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
> Reviewed-by: Rob Herring <robh@kernel.org>
> ---
>  Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
>  1 file changed, 1 insertion(+)

I've converted this file to json-schema as of v5.2-rc1. See commit
8122de54602e. Sorry, but you will have to rework this patch.


Rob

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 9+ messages in thread

* Re: [PATCH v12 1/4] MAINTAINERS: add an entry for for arm64 imx devicetrees
  2019-05-14 13:28 ` [PATCH v12 1/4] MAINTAINERS: add an entry for for arm64 imx devicetrees Angus Ainslie (Purism)
@ 2019-05-22  8:30   ` Shawn Guo
  2019-05-22 13:46     ` Angus Ainslie
  0 siblings, 1 reply; 9+ messages in thread
From: Shawn Guo @ 2019-05-22  8:30 UTC (permalink / raw)
  To: Angus Ainslie (Purism)
  Cc: Mark Rutland, devicetree, Sascha Hauer, linux-kernel, Li Yang,
	Rob Herring, NXP Linux Team, Pengutronix Kernel Team,
	angus.ainslie, Fabio Estevam, linux-arm-kernel

On Tue, May 14, 2019 at 06:28:19AM -0700, Angus Ainslie (Purism) wrote:
> Add an explicit reference to imx* devicetrees
> 
> Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
> Reviewed-by: Fabio Estevam <festevam@gmail.com>
> ---
>  MAINTAINERS | 1 +
>  1 file changed, 1 insertion(+)
> 
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 7707c28628b9..9fc30f82ab81 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -1624,6 +1624,7 @@ R:	NXP Linux Team <linux-imx@nxp.com>
>  L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
>  S:	Maintained
>  T:	git git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux.git
> +F:	arch/arm64/boot/dts/freescale/imx*

This is partially reverting commit da8b7f0fb02b ("MAINTAINERS: add all
files matching "imx" and "mxs" to the IMX entry").  I'm not sure that we
want it.

Shawn

>  N:	imx
>  N:	mxs
>  X:	drivers/media/i2c/
> -- 
> 2.17.1
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 9+ messages in thread

* Re: [PATCH v12 2/4] arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit
  2019-05-14 13:28 ` [PATCH v12 2/4] arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit Angus Ainslie (Purism)
@ 2019-05-22  8:57   ` Shawn Guo
  0 siblings, 0 replies; 9+ messages in thread
From: Shawn Guo @ 2019-05-22  8:57 UTC (permalink / raw)
  To: Angus Ainslie (Purism)
  Cc: Mark Rutland, devicetree, Sascha Hauer, linux-kernel, Li Yang,
	Rob Herring, NXP Linux Team, Pengutronix Kernel Team,
	angus.ainslie, Fabio Estevam, linux-arm-kernel

On Tue, May 14, 2019 at 06:28:20AM -0700, Angus Ainslie (Purism) wrote:
> This is for the development kit board for the Librem 5. The current level
> of support yields a working console and is able to boot userspace from
> the network or eMMC.
> 
> Additional subsystems that are active :
> 
> - Both USB ports
> - SD card socket
> - WiFi usdhc
> - WWAN modem
> - GNSS
> - GPIO keys
> - LEDs
> - gyro
> - magnetometer
> - touchscreen
> - pwm
> - backlight
> - haptic motor
> 
> Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
> Reviewed-by: Fabio Estevam <festevam@gmail.com>
> ---
>  arch/arm64/boot/dts/freescale/Makefile        |   1 +
>  .../dts/freescale/imx8mq-librem5-devkit.dts   | 821 ++++++++++++++++++
>  2 files changed, 822 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
> 
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index 0bd122f60549..c043aca66572 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -22,6 +22,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
>  
>  dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mq-evk.dtb
> +dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-rmb3.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-zest.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8qxp-mek.dtb
> diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
> new file mode 100644
> index 000000000000..64898daee644
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
> @@ -0,0 +1,821 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright 2018-2019 Purism SPC
> + */
> +
> +/dts-v1/;
> +
> +#include "dt-bindings/input/input.h"
> +#include "dt-bindings/usb/pd.h"
> +#include "imx8mq.dtsi"
> +
> +/ {
> +	model = "Purism Librem 5 devkit";
> +	compatible = "purism,librem5-devkit", "fsl,imx8mq";
> +
> +	backlight_dsi: backlight-dsi {
> +		compatible = "pwm-backlight";
> +		/* 200 Hz for the PAM2841 */
> +		pwms = <&pwm1 0 5000000>;
> +		brightness-levels = <0 100>;
> +		num-interpolated-steps = <100>;
> +		/* Default brightness level (index into the array defined by */
> +		/* the "brightness-levels" property) */
> +		default-brightness-level = <0>;
> +		power-supply = <&reg_22v4_p>;
> +	};
> +
> +	chosen {
> +		stdout-path = &uart1;
> +	};
> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_gpio_keys>;
> +
> +		btn1 {
> +			label = "VOL_UP";
> +			gpios = <&gpio4 21 GPIO_ACTIVE_LOW>;
> +			wakeup-source;
> +			linux,code = <KEY_VOLUMEUP>;
> +		};
> +
> +		btn2 {
> +			label = "VOL_DOWN";
> +			gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
> +			wakeup-source;
> +			linux,code = <KEY_VOLUMEDOWN>;
> +		};
> +
> +		hp_det {

We prefer to use hyphen than underscore in node name.

> +			label = "HP_DET";
> +			gpios = <&gpio3 20 GPIO_ACTIVE_LOW>;
> +			wakeup-source;
> +			linux,code = <KEY_HP>;
> +		};
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_gpio_leds>;
> +
> +		led1 {
> +			label = "LED 1";
> +			gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
> +			default-state = "off";
> +		};
> +	};
> +
> +	pmic_osc: pmic-osc {

clock-xxx as node name for fixed clock.

> +		compatible = "fixed-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <32768>;
> +		clock-output-names = "pmic_osc";
> +	};
> +
> +	pwmleds {
> +		compatible = "pwm-leds";
> +
> +		haptic {
> +			label = "librem5::haptic";
> +			pwms = <&pwm2 0 200000>;
> +			active-low;
> +			max-brightness = <255>;
> +			power-supply = <&reg_3v3_p>;

I do not see that 'power-supply' is a pwm led property in
bindings/leds/leds-pwm.txt.  Is it something missed from bindings doc or
that shouldn't be here?

> +		};
> +	};
> +
> +	reg_1v8_p: regulator-1v8-p {
> +		compatible = "regulator-fixed";
> +		regulator-name = "1v8_p";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +		vin-supply = <&reg_pwr_en>;
> +	};
> +
> +	reg_2v8_p: regulator-2v8-p {
> +		compatible = "regulator-fixed";
> +		regulator-name = "2v8_p";
> +		regulator-min-microvolt = <2800000>;
> +		regulator-max-microvolt = <2800000>;
> +		vin-supply = <&reg_pwr_en>;
> +	};
> +
> +	reg_3v3_p: regulator-3v3-p {
> +		compatible = "regulator-fixed";
> +		regulator-name = "3v3_p";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		vin-supply = <&reg_pwr_en>;
> +		regulator-state-mem {
> +			regulator-on-in-suspend;
> +		};
> +	};
> +
> +	reg_5v_p: regulator-5v-p {
> +		compatible = "regulator-fixed";
> +		regulator-name = "5v_p";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		vin-supply = <&reg_pwr_en>;

Please have a newline between property list and child node.

> +		regulator-state-mem {
> +			regulator-on-in-suspend;
> +		};
> +	};
> +
> +	reg_22v4_p: regulator-22v4-p {
> +		compatible = "regulator-fixed";
> +		regulator-name = "22v4_P";
> +		regulator-min-microvolt = <22400000>;
> +		regulator-max-microvolt = <22400000>;
> +		vin-supply = <&reg_pwr_en>;
> +	};
> +
> +	reg_pwr_en: regulator-pwr-en {
> +		compatible = "regulator-fixed";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_pwr_en>;
> +		regulator-name = "PWR_EN";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpio = <&gpio1 8 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +		regulator-always-on;
> +	};
> +
> +	reg_usdhc2_vmmc: regulator-usdhc2-vmmc {
> +		compatible = "regulator-fixed";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_usdhc2_pwr>;
> +		regulator-name = "VSD_3V3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +		regulator-always-on;
> +	};
> +
> +	wifi_pwr_en: wifi-en {

regulator-wifi-en

> +		compatible = "regulator-fixed";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_wifi_pwr_en>;
> +		regulator-name = "WIFI_EN";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpio = <&gpio3 5 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +		regulator-always-on;
> +	};
> +};
> +
> +&clk {
> +	assigned-clocks = <&clk IMX8MQ_AUDIO_PLL1>, <&clk IMX8MQ_AUDIO_PLL2>;
> +	assigned-clock-rates = <786432000>, <722534400>;
> +};
> +
> +&fec1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_fec1>;
> +	phy-mode = "rgmii-id";
> +	phy-handle = <&ethphy0>;
> +	fsl,magic-packet;
> +	phy-supply = <&reg_3v3_p>;
> +	status = "okay";
> +
> +	mdio {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		ethphy0: ethernet-phy@1 {
> +			compatible = "ethernet-phy-ieee802.3-c22";
> +			reg = <1>;
> +		};
> +	};
> +};
> +
> +&i2c1 {
> +	clock-frequency = <100000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c1>;
> +	status = "okay";
> +
> +	pmic: pmic@4b {
> +		compatible = "rohm,bd71837";
> +		reg = <0x4b>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_pmic>;
> +		clocks = <&pmic_osc>;
> +		clock-names = "osc";
> +		clock-output-names = "pmic_clk";
> +		interrupt-parent = <&gpio1>;
> +		interrupts = <3 GPIO_ACTIVE_LOW>;
> +		interrupt-names = "irq";
> +		rohm,reset-snvs-powered;
> +
> +		regulators {
> +

Unnecessary newline.

> +			buck1_reg: BUCK1 {
> +				regulator-name = "buck1";
> +				regulator-min-microvolt = <700000>;
> +				regulator-max-microvolt = <1300000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +				regulator-ramp-delay = <1250>;
> +				rohm,dvs-run-voltage = <900000>;
> +				rohm,dvs-idle-voltage = <850000>;
> +				rohm,dvs-suspend-voltage = <800000>;
> +			};
> +
> +			buck2_reg: BUCK2 {
> +				regulator-name = "buck2";
> +				regulator-min-microvolt = <700000>;
> +				regulator-max-microvolt = <1300000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +				regulator-ramp-delay = <1250>;
> +				rohm,dvs-run-voltage = <1000000>;
> +				rohm,dvs-idle-voltage = <900000>;
> +			};
> +
> +			buck3_reg: BUCK3 {
> +				regulator-name = "buck3";
> +				regulator-min-microvolt = <700000>;
> +				regulator-max-microvolt = <1300000>;
> +				rohm,dvs-run-voltage = <1000000>;
> +			};
> +
> +			buck4_reg: BUCK4 {
> +				regulator-name = "buck4";
> +				regulator-min-microvolt = <700000>;
> +				regulator-max-microvolt = <1300000>;
> +				rohm,dvs-run-voltage = <1000000>;
> +			};
> +
> +			buck5_reg: BUCK5 {
> +				regulator-name = "buck5";
> +				regulator-min-microvolt = <700000>;
> +				regulator-max-microvolt = <1350000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			buck6_reg: BUCK6 {
> +				regulator-name = "buck6";
> +				regulator-min-microvolt = <3000000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			buck7_reg: BUCK7 {
> +				regulator-name = "buck7";
> +				regulator-min-microvolt = <1605000>;
> +				regulator-max-microvolt = <1995000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			buck8_reg: BUCK8 {
> +				regulator-name = "buck8";
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <1400000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			ldo1_reg: LDO1 {
> +				regulator-name = "ldo1";
> +				regulator-min-microvolt = <3000000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			ldo2_reg: LDO2 {
> +				regulator-name = "ldo2";
> +				regulator-min-microvolt = <900000>;
> +				regulator-max-microvolt = <900000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			ldo3_reg: LDO3 {
> +				regulator-name = "ldo3";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			ldo4_reg: LDO4 {
> +				regulator-name = "ldo4";
> +				regulator-min-microvolt = <900000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			ldo5_reg: LDO5 {
> +				regulator-name = "ldo5";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <3300000>;
> +			};
> +
> +			ldo6_reg: LDO6 {
> +				regulator-name = "ldo6";
> +				regulator-min-microvolt = <900000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			ldo7_reg: LDO7 {
> +				regulator-name = "ldo7";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +		};
> +	};
> +
> +	typec_ptn5100: usb_typec@52 {
> +		compatible = "nxp,ptn5110";
> +		reg = <0x52>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_typec>;
> +		interrupt-parent = <&gpio3>;
> +		interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
> +
> +		connector {
> +			compatible = "usb-c-connector";
> +			label = "USB-C";
> +			data-role = "dual";
> +			power-role = "dual";
> +			try-power-role = "sink";
> +			source-pdos = <PDO_FIXED(5000, 2000,
> +				PDO_FIXED_USB_COMM |
> +				PDO_FIXED_DUAL_ROLE |
> +				PDO_FIXED_DATA_SWAP )>;
> +			sink-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM |
> +				PDO_FIXED_DUAL_ROLE |
> +				PDO_FIXED_DATA_SWAP )
> +			     PDO_VAR(5000, 12000, 2000)>;
> +			op-sink-microwatt = <10000000>;
> +
> +			ports {
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				port@0 {
> +					reg = <0>;

Have a newline between properties and child node.

> +					usb_con_hs: endpoint {
> +						remote-endpoint = <&typec_hs>;
> +					};
> +				};
> +
> +				port@1 {
> +					reg = <1>;
> +					usb_con_ss: endpoint {
> +						remote-endpoint = <&typec_ss>;
> +					};
> +				};
> +			};
> +		};
> +	};
> +
> +	rtc@68 {
> +		compatible = "microcrystal,rv4162";
> +		reg = <0x68>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_rtc>;
> +		interrupt-parent = <&gpio4>;
> +		interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
> +	};
> +
> +	charger@6b { /* bq25896 */
> +		compatible = "ti,bq25890";
> +		reg = <0x6b>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_charger>;
> +		interrupt-parent = <&gpio3>;
> +		interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
> +		ti,battery-regulation-voltage = <4192000>; /* 4.192V */
> +		ti,charge-current = <1600000>; /* 1.6 A */
> +		ti,termination-current = <66000>;  /* 66mA */
> +		ti,precharge-current = <1300000>; /* 1.3A */
> +		ti,minimum-sys-voltage = <2750000>; /* 2.75V */
> +		ti,boost-voltage = <5000000>; /* 5V */
> +		ti,boost-max-current = <50000>; /* 50mA */
> +	};
> +};
> +
> +&i2c3 {
> +	clock-frequency = <100000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c3>;
> +	status = "okay";
> +
> +	magnetometer@1e	{
> +		compatible = "st,lsm9ds1-magn";
> +		reg = <0x1e>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_imu>;
> +		interrupt-parent = <&gpio3>;
> +		interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
> +		vdd-supply = <&reg_3v3_p>;
> +		vddio-supply = <&reg_3v3_p>;
> +	};
> +
> +	touchscreen@5d {
> +		compatible = "goodix,gt5688";
> +		reg = <0x5d>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_goodix_ts>;
> +		interrupt-parent = <&gpio3>;
> +		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> +		reset-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
> +		irq-gpios = <&gpio3 0 GPIO_ACTIVE_HIGH>;
> +		touchscreen-size-x = <720>;
> +		touchscreen-size-y = <1440>;
> +		AVDD28-supply = <&reg_2v8_p>;
> +		VDDIO-supply = <&reg_1v8_p>;
> +	};
> +};
> +
> +&iomuxc {
> +	pinctrl_backlight: pwm1 {

Name the label and node more consistently, preferably like:

	pinctrl_xxx: xxxgrp

> +		fsl,pins = <
> +		MX8MQ_IOMUXC_GPIO1_IO01_PWM1_OUT	0x6  /* DSI_BL_PWM */

Please have one more level of indentation.  It's fine to get the lines
longer than 80 columns in this case.

Shawn

> +		>;
> +	};
> +
> +	pinctrl_bt: btgrp {
> +		fsl,pins = <
> +		/* nBT_DISABLE */
> +		MX8MQ_IOMUXC_NAND_DATA05_GPIO3_IO11             0x16
> +		/* BT_HOST_WAKE */
> +		MX8MQ_IOMUXC_NAND_DATA01_GPIO3_IO7              0x10
> +		>;
> +	};
> +
> +	pinctrl_charger: chargernirq {
> +		fsl,pins = <
> +		/* CHRG_nINT */
> +		MX8MQ_IOMUXC_SAI5_MCLK_GPIO3_IO25	0x80
> +		>;
> +	};
> +
> +	pinctrl_fec1: fec1grp {
> +		fsl,pins = <
> +		MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC		0x3
> +		MX8MQ_IOMUXC_ENET_MDIO_ENET1_MDIO	0x3
> +		MX8MQ_IOMUXC_ENET_TD3_ENET1_RGMII_TD3	0x1f
> +		MX8MQ_IOMUXC_ENET_TD2_ENET1_RGMII_TD2	0x1f
> +		MX8MQ_IOMUXC_ENET_TD1_ENET1_RGMII_TD1	0x1f
> +		MX8MQ_IOMUXC_ENET_TD0_ENET1_RGMII_TD0	0x1f
> +		MX8MQ_IOMUXC_ENET_RD3_ENET1_RGMII_RD3	0x91
> +		MX8MQ_IOMUXC_ENET_RD2_ENET1_RGMII_RD2	0x91
> +		MX8MQ_IOMUXC_ENET_RD1_ENET1_RGMII_RD1	0x91
> +		MX8MQ_IOMUXC_ENET_RD0_ENET1_RGMII_RD0	0x91
> +		MX8MQ_IOMUXC_ENET_TXC_ENET1_RGMII_TXC	0x1f
> +		MX8MQ_IOMUXC_ENET_RXC_ENET1_RGMII_RXC	0x91
> +		MX8MQ_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91
> +		MX8MQ_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f
> +		MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9	0x19
> +		MX8MQ_IOMUXC_GPIO1_IO15_CCMSRCGPCMIX_CLKO2      0x1f
> +		>;
> +	};
> +
> +	pinctrl_goodix_ts: gt5688 {
> +		fsl,pins = <
> +		/* TOUCH INT */
> +		MX8MQ_IOMUXC_NAND_ALE_GPIO3_IO0         0x16
> +		/* TOUCH RST */
> +		MX8MQ_IOMUXC_GPIO1_IO05_GPIO1_IO5	0x19
> +		>;
> +	};
> +
> +	pinctrl_gpio_leds: gpioleds {
> +		fsl,pins = <
> +		MX8MQ_IOMUXC_GPIO1_IO13_GPIO1_IO13	0x16
> +		>;
> +	};
> +
> +	pinctrl_gpio_keys: gpiokeys {
> +		fsl,pins = <
> +		MX8MQ_IOMUXC_SAI2_RXFS_GPIO4_IO21	0x16
> +		MX8MQ_IOMUXC_SAI2_RXC_GPIO4_IO22	0x16
> +		/* HP_DET */
> +		MX8MQ_IOMUXC_SAI5_RXC_GPIO3_IO20	0x180
> +		>;
> +	};
> +
> +	pinctrl_haptic: hapticgrp {
> +		fsl,pins = <
> +		MX8MQ_IOMUXC_SPDIF_RX_PWM2_OUT		0xc6  /* nHAPTIC */
> +		>;
> +	};
> +
> +	pinctrl_i2c1: i2c1grp {
> +		fsl,pins = <
> +		MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL		0x4000001f
> +		MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA		0x4000001f
> +		>;
> +	};
> +
> +	pinctrl_i2c3: i2c3grp {
> +		fsl,pins = <
> +		MX8MQ_IOMUXC_I2C3_SCL_I2C3_SCL		0x4000001f
> +		MX8MQ_IOMUXC_I2C3_SDA_I2C3_SDA		0x4000001f
> +		>;
> +	};
> +
> +	pinctrl_imu: imugrp {
> +		fsl,pins = <
> +		/* IMU_INT */
> +		MX8MQ_IOMUXC_SAI5_RXFS_GPIO3_IO19	0x8
> +		>;
> +	};
> +
> +	pinctrl_pmic: pmicint {
> +		fsl,pins = <
> +		MX8MQ_IOMUXC_GPIO1_IO03_GPIO1_IO3	0x80
> +		>;
> +	};
> +
> +	pinctrl_pwr_en: pwrengrp {
> +		fsl,pins = <
> +		MX8MQ_IOMUXC_GPIO1_IO08_GPIO1_IO8               0x06
> +		>;
> +	};
> +
> +	pinctrl_rtc: rtcirq {
> +		fsl,pins = <
> +		MX8MQ_IOMUXC_SAI3_RXC_GPIO4_IO29	0x80
> +		>;
> +	};
> +
> +	pinctrl_typec: typecgrp {
> +		fsl,pins = <
> +		MX8MQ_IOMUXC_NAND_DATA06_GPIO3_IO12	0x16
> +		MX8MQ_IOMUXC_NAND_CE0_B_GPIO3_IO1	0x80
> +		>;
> +	};
> +
> +	pinctrl_uart1: uart1grp {
> +		fsl,pins = <
> +		MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX		0x49
> +		MX8MQ_IOMUXC_UART1_TXD_UART1_DCE_TX		0x49
> +		>;
> +	};
> +
> +	pinctrl_uart2: uart2grp {
> +		fsl,pins = <
> +		MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX		0x49
> +		MX8MQ_IOMUXC_UART2_RXD_UART2_DCE_RX		0x49
> +		MX8MQ_IOMUXC_UART4_RXD_UART2_DCE_CTS_B		0x49
> +		MX8MQ_IOMUXC_UART4_TXD_UART2_DCE_RTS_B		0x49
> +		>;
> +	};
> +
> +	pinctrl_uart3: uart3grp {
> +		fsl,pins = <
> +		MX8MQ_IOMUXC_UART3_RXD_UART3_DCE_RX		0x49
> +		MX8MQ_IOMUXC_UART3_TXD_UART3_DCE_TX		0x49
> +		>;
> +	};
> +
> +	pinctrl_uart4: uart4grp {
> +		fsl,pins = <
> +		MX8MQ_IOMUXC_ECSPI2_SCLK_UART4_DCE_RX		0x49
> +		MX8MQ_IOMUXC_ECSPI2_MOSI_UART4_DCE_TX		0x49
> +		MX8MQ_IOMUXC_ECSPI2_MISO_UART4_DCE_CTS_B	0x49
> +		MX8MQ_IOMUXC_ECSPI2_SS0_UART4_DCE_RTS_B		0x49
> +		MX8MQ_IOMUXC_GPIO1_IO00_ANAMIX_REF_CLK_32K	0x49
> +		>;
> +	};
> +
> +	pinctrl_usdhc1: usdhc1grp {
> +		fsl,pins = <
> +		MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK			0x83
> +		MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD			0xc3
> +		MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0		0xc3
> +		MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1		0xc3
> +		MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2		0xc3
> +		MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3		0xc3
> +		MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4		0xc3
> +		MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5		0xc3
> +		MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6		0xc3
> +		MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7		0xc3
> +		MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x83
> +		MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B		0xc1
> +		>;
> +	};
> +
> +	pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
> +		fsl,pins = <
> +		MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK			0x8d
> +		MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD			0xcd
> +		MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0		0xcd
> +		MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1		0xcd
> +		MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2		0xcd
> +		MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3		0xcd
> +		MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4		0xcd
> +		MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5		0xcd
> +		MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6		0xcd
> +		MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7		0xcd
> +		MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x8d
> +		MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B		0xc1
> +		>;
> +	};
> +
> +	pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
> +		fsl,pins = <
> +		MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK			0x9f
> +		MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD			0xdf
> +		MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0		0xdf
> +		MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1		0xdf
> +		MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2		0xdf
> +		MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3		0xdf
> +		MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4		0xdf
> +		MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5		0xdf
> +		MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6		0xdf
> +		MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7		0xdf
> +		MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x9f
> +		MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B		0xc1
> +		>;
> +	};
> +
> +	pinctrl_usdhc2_pwr: usdhc2grppwr {
> +		fsl,pins = <
> +		MX8MQ_IOMUXC_SD2_RESET_B_GPIO2_IO19		0x41
> +		>;
> +	};
> +
> +	pinctrl_usdhc2_gpio: usdhc2grpgpio {
> +		fsl,pins = <
> +		/* WIFI_WAKE */
> +		MX8MQ_IOMUXC_SD2_WP_GPIO2_IO20			0x80
> +		>;
> +	};
> +
> +	pinctrl_usdhc2: usdhc2grp {
> +		fsl,pins = <
> +		MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK			0x83
> +		MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD			0xc3
> +		MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0		0xc3
> +		MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1		0xc3
> +		MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2		0xc3
> +		MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3		0xc3
> +		>;
> +	};
> +
> +	pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
> +		fsl,pins = <
> +		MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK			0x8d
> +		MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD			0xcd
> +		MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0		0xcd
> +		MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1		0xcd
> +		MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2		0xcd
> +		MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3		0xcd
> +		>;
> +	};
> +
> +	pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
> +		fsl,pins = <
> +		MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK			0x9f
> +		MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD			0xcf
> +		MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0		0xcf
> +		MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1		0xcf
> +		MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2		0xcf
> +		MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3		0xcf
> +		>;
> +	};
> +
> +	pinctrl_wdog: wdoggrp {
> +		fsl,pins = <
> +		MX8MQ_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B	0xc6
> +		>;
> +	};
> +
> +	pinctrl_wifi_pwr_en: wifipwrengrp {
> +		fsl,pins = <
> +		MX8MQ_IOMUXC_NAND_CLE_GPIO3_IO5         0x06
> +		>;
> +	};
> +
> +	pinctrl_wwan: wwangrp {
> +		fsl,pins = <
> +		/* nWWAN_DISABLE */
> +		MX8MQ_IOMUXC_NAND_CE3_B_GPIO3_IO4	0x09
> +		/* nWoWWAN */
> +		MX8MQ_IOMUXC_NAND_DATA02_GPIO3_IO8	0x80
> +		/* WWAN_RESET */
> +		MX8MQ_IOMUXC_NAND_DATA03_GPIO3_IO9	0x19
> +		>;
> +	};
> +};
> +
> +&pwm1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_backlight>;
> +	status = "okay";
> +};
> +
> +&pwm2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_haptic>;
> +	status = "okay";
> +};
> +
> +&uart1 { /* console */
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart1>;
> +	status = "okay";
> +};
> +
> +&uart3 { /* GNSS */
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart3>;
> +	status = "okay";
> +};
> +
> +&uart4 { /* BT */
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart4>, <&pinctrl_bt>;
> +	uart-has-rtscts;
> +	status = "okay";
> +};
> +
> +&usb3_phy0 {
> +	status = "okay";
> +};
> +
> +&usb3_phy1 {
> +	vbus-supply = <&reg_5v_p>;
> +	status = "okay";
> +};
> +
> +&usb_dwc3_0 {
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	dr_mode = "otg";
> +	status = "okay";
> +
> +	port@0 {
> +		reg = <0>;
> +
> +		typec_hs: endpoint {
> +			remote-endpoint = <&usb_con_hs>;
> +		};
> +	};
> +
> +	port@1 {
> +		reg = <1>;
> +
> +		typec_ss: endpoint {
> +			remote-endpoint = <&usb_con_ss>;
> +		};
> +	};
> +};
> +
> +&usb_dwc3_1 {
> +	dr_mode = "host";
> +	status = "okay";
> +};
> +
> +&usdhc1 {
> +	pinctrl-names = "default", "state_100mhz", "state_200mhz";
> +	pinctrl-0 = <&pinctrl_usdhc1>;
> +	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
> +	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
> +	bus-width = <8>;
> +	non-removable;
> +	status = "okay";
> +};
> +
> +&usdhc2 {
> +	pinctrl-names = "default", "state_100mhz", "state_200mhz";
> +	pinctrl-0 = <&pinctrl_usdhc2>;
> +	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
> +	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
> +	bus-width = <4>;
> +	vmmc-supply = <&reg_usdhc2_vmmc>;
> +	power-supply = <&wifi_pwr_en>;
> +	non-removable;
> +	disable-wp;
> +	cap-sdio-irq;
> +	keep-power-in-suspend;
> +	wakeup-source;
> +	status = "okay";
> +};
> +
> +&wdog1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_wdog>;
> +	fsl,ext-reset-output;
> +	status = "okay";
> +};
> -- 
> 2.17.1
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 9+ messages in thread

* Re: [PATCH v12 1/4] MAINTAINERS: add an entry for for arm64 imx devicetrees
  2019-05-22  8:30   ` Shawn Guo
@ 2019-05-22 13:46     ` Angus Ainslie
  0 siblings, 0 replies; 9+ messages in thread
From: Angus Ainslie @ 2019-05-22 13:46 UTC (permalink / raw)
  To: Shawn Guo
  Cc: Mark Rutland, devicetree, Sascha Hauer, linux-kernel, Li Yang,
	Rob Herring, NXP Linux Team, Pengutronix Kernel Team,
	angus.ainslie, Fabio Estevam, linux-arm-kernel

Hi Shawn

On 2019-05-22 01:30, Shawn Guo wrote:
> On Tue, May 14, 2019 at 06:28:19AM -0700, Angus Ainslie (Purism) wrote:
>> Add an explicit reference to imx* devicetrees
>> 
>> Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
>> Reviewed-by: Fabio Estevam <festevam@gmail.com>
>> ---
>>  MAINTAINERS | 1 +
>>  1 file changed, 1 insertion(+)
>> 
>> diff --git a/MAINTAINERS b/MAINTAINERS
>> index 7707c28628b9..9fc30f82ab81 100644
>> --- a/MAINTAINERS
>> +++ b/MAINTAINERS
>> @@ -1624,6 +1624,7 @@ R:	NXP Linux Team <linux-imx@nxp.com>
>>  L:	linux-arm-kernel@lists.infradead.org (moderated for 
>> non-subscribers)
>>  S:	Maintained
>>  T:	git 
>> git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux.git
>> +F:	arch/arm64/boot/dts/freescale/imx*
> 
> This is partially reverting commit da8b7f0fb02b ("MAINTAINERS: add all
> files matching "imx" and "mxs" to the IMX entry").  I'm not sure that 
> we
> want it.
> 

Ok, I can drop it from my patchset and it will get sorted out somewhere 
else ?

Thanks
Angus

> Shawn
> 
>>  N:	imx
>>  N:	mxs
>>  X:	drivers/media/i2c/
>> --
>> 2.17.1
>> 


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 9+ messages in thread

end of thread, back to index

Thread overview: 9+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-05-14 13:28 [PATCH v12 0/4] Add support for the Purism Librem5 devkit Angus Ainslie (Purism)
2019-05-14 13:28 ` [PATCH v12 1/4] MAINTAINERS: add an entry for for arm64 imx devicetrees Angus Ainslie (Purism)
2019-05-22  8:30   ` Shawn Guo
2019-05-22 13:46     ` Angus Ainslie
2019-05-14 13:28 ` [PATCH v12 2/4] arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit Angus Ainslie (Purism)
2019-05-22  8:57   ` Shawn Guo
2019-05-14 13:28 ` [PATCH v12 3/4] dt-bindings: Add an entry for Purism SPC Angus Ainslie (Purism)
2019-05-17  2:31   ` Rob Herring
2019-05-14 13:28 ` [PATCH v12 4/4] dt-bindings: arm: fsl: Add the imx8mq boards Angus Ainslie (Purism)

Linux-ARM-Kernel Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-arm-kernel/0 linux-arm-kernel/git/0.git
	git clone --mirror https://lore.kernel.org/linux-arm-kernel/1 linux-arm-kernel/git/1.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-arm-kernel linux-arm-kernel/ https://lore.kernel.org/linux-arm-kernel \
		linux-arm-kernel@lists.infradead.org infradead-linux-arm-kernel@archiver.kernel.org
	public-inbox-index linux-arm-kernel


Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.infradead.lists.linux-arm-kernel


AGPL code for this site: git clone https://public-inbox.org/ public-inbox