Linux-ARM-Kernel Archive on lore.kernel.org
 help / color / Atom feed
From: Yangtao Li <tiny.windzz@gmail.com>
To: rui.zhang@intel.com, edubezval@gmail.com,
	daniel.lezcano@linaro.org, robh+dt@kernel.org,
	mark.rutland@arm.com, maxime.ripard@bootlin.com, wens@csie.org,
	davem@davemloft.net, mchehab+samsung@kernel.org,
	gregkh@linuxfoundation.org, linus.walleij@linaro.org,
	nicolas.ferre@microchip.com, paulmck@linux.ibm.com
Cc: Yangtao Li <tiny.windzz@gmail.com>,
	devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
	linux-arm-kernel@lists.infradead.org, linux-pm@vger.kernel.org
Subject: [PATCH v3 1/3] thermal: sun8i: add thermal driver for h6
Date: Sat, 25 May 2019 14:13:27 -0400
Message-ID: <20190525181329.18657-2-tiny.windzz@gmail.com> (raw)
In-Reply-To: <20190525181329.18657-1-tiny.windzz@gmail.com>

This patch adds the support for allwinner thermal sensor, within
allwinner SoC. It will register sensors for thermal framework
and use device tree to bind cooling device.

Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
---
 MAINTAINERS                     |   7 +
 drivers/thermal/Kconfig         |  14 +
 drivers/thermal/Makefile        |   1 +
 drivers/thermal/sun8i_thermal.c | 437 ++++++++++++++++++++++++++++++++
 4 files changed, 459 insertions(+)
 create mode 100644 drivers/thermal/sun8i_thermal.c

diff --git a/MAINTAINERS b/MAINTAINERS
index 2336dd26ece4..d312f9eecf0d 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -674,6 +674,13 @@ L:	linux-crypto@vger.kernel.org
 S:	Maintained
 F:	drivers/crypto/sunxi-ss/
 
+ALLWINNER THERMAL DRIVER
+M:	Yangtao Li <tiny.windzz@gmail.com>
+L:	linux-pm@vger.kernel.org
+S:	Maintained
+F:	Documentation/devicetree/bindings/thermal/sun8i-thermal.yaml
+F:	drivers/thermal/sun8i_thermal.c
+
 ALLWINNER VPU DRIVER
 M:	Maxime Ripard <maxime.ripard@bootlin.com>
 M:	Paul Kocialkowski <paul.kocialkowski@bootlin.com>
diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
index 9966364a6deb..e5465053d66f 100644
--- a/drivers/thermal/Kconfig
+++ b/drivers/thermal/Kconfig
@@ -262,6 +262,20 @@ config SPEAR_THERMAL
 	  Enable this to plug the SPEAr thermal sensor driver into the Linux
 	  thermal framework.
 
+config SUN8I_THERMAL
+	tristate "Allwinner sun8i thermal driver"
+	depends on ARCH_SUNXI || COMPILE_TEST
+	depends on HAS_IOMEM
+	depends on NVMEM_SUNXI_SID
+	depends on OF
+	depends on RESET_CONTROLLER
+	help
+	  Support for the sun8i thermal sensor driver into the Linux thermal
+	  framework.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called sun8i-thermal.
+
 config ROCKCHIP_THERMAL
 	tristate "Rockchip thermal driver"
 	depends on ARCH_ROCKCHIP || COMPILE_TEST
diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
index 74a37c7f847a..fa6f8b206281 100644
--- a/drivers/thermal/Makefile
+++ b/drivers/thermal/Makefile
@@ -31,6 +31,7 @@ thermal_sys-$(CONFIG_DEVFREQ_THERMAL) += devfreq_cooling.o
 obj-y				+= broadcom/
 obj-$(CONFIG_THERMAL_MMIO)		+= thermal_mmio.o
 obj-$(CONFIG_SPEAR_THERMAL)	+= spear_thermal.o
+obj-$(CONFIG_SUN8I_THERMAL)     += sun8i_thermal.o
 obj-$(CONFIG_ROCKCHIP_THERMAL)	+= rockchip_thermal.o
 obj-$(CONFIG_RCAR_THERMAL)	+= rcar_thermal.o
 obj-$(CONFIG_RCAR_GEN3_THERMAL)	+= rcar_gen3_thermal.o
diff --git a/drivers/thermal/sun8i_thermal.c b/drivers/thermal/sun8i_thermal.c
new file mode 100644
index 000000000000..a9cc2197f4cb
--- /dev/null
+++ b/drivers/thermal/sun8i_thermal.c
@@ -0,0 +1,437 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Thermal sensor driver for Allwinner SOC
+ * Copyright (C) 2019 Yangtao Li
+ *
+ * Based on the work of Icenowy Zheng <icenowy@aosc.io>
+ * Based on the work of Ondrej Jirman <megous@megous.com>
+ * Based on the work of Josef Gajdusek <atx@atx.name>
+ */
+
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/interrupt.h>
+#include <linux/wait.h>
+#include <linux/module.h>
+#include <linux/nvmem-consumer.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+#include <linux/slab.h>
+#include <linux/thermal.h>
+
+#define MAX_SENSOR_NUM	4
+
+#define FT_TEMP_MASK				GENMASK(11, 0)
+#define TEMP_CALIB_MASK				GENMASK(11, 0)
+#define TEMP_TO_REG				672
+#define CALIBRATE_DEFAULT			0x800
+
+#define SUN50I_THS_CTRL0			0x00
+#define SUN50I_H6_THS_ENABLE			0x04
+#define SUN50I_H6_THS_PC			0x08
+#define SUN50I_H6_THS_DIC			0x10
+#define SUN50I_H6_THS_DIS			0x20
+#define SUN50I_H6_THS_MFC			0x30
+#define SUN50I_H6_THS_TEMP_CALIB		0xa0
+#define SUN50I_H6_THS_TEMP_DATA			0xc0
+
+#define SUN50I_THS_CTRL0_T_ACQ(x)		((GENMASK(15, 0) & (x)) << 16)
+#define SUN50I_THS_FILTER_EN			BIT(2)
+#define SUN50I_THS_FILTER_TYPE(x)		(GENMASK(1, 0) & (x))
+#define SUN50I_H6_THS_PC_TEMP_PERIOD(x)		((GENMASK(19, 0) & (x)) << 12)
+#define SUN50I_H6_THS_DATA_IRQ_STS(x)		BIT(x)
+
+/* millidegree celsius */
+#define SUN50I_H6_FT_DEVIATION			7000
+
+struct ths_device;
+
+struct tsensor {
+	struct ths_device		*tmdev;
+	struct thermal_zone_device	*tzd;
+	int				id;
+	wait_queue_head_t		wait_queue;
+};
+
+struct ths_thermal_chip {
+	int		sensor_num;
+	int		offset;
+	int		scale;
+	int		ft_deviation;
+	int		temp_calib_base;
+	int		temp_data_base;
+	int		(*calibrate)(struct ths_device *tmdev);
+	int		(*init)(struct ths_device *tmdev);
+	irqreturn_t	(*irq_thread)(int irq, void *data);
+};
+
+struct ths_device {
+	const struct ths_thermal_chip		*chip;
+	struct device				*dev;
+	struct regmap				*regmap;
+	struct reset_control			*reset;
+	struct clk				*bus_clk;
+	struct tsensor				sensor[MAX_SENSOR_NUM];
+	int					data_ready;
+};
+
+/* Temp Unit: millidegree Celsius */
+static int sun8i_ths_reg2temp(struct ths_device *tmdev,
+			      int reg)
+{
+	return (reg + tmdev->chip->offset) * tmdev->chip->scale;
+}
+
+static int sun8i_ths_get_temp(void *data, int *temp)
+{
+	struct tsensor *s = data;
+	struct ths_device *tmdev = s->tmdev;
+	int val;
+
+	wait_event(s->wait_queue, tmdev->data_ready & BIT(s->id));
+	tmdev->data_ready &= ~BIT(s->id);
+
+	regmap_read(tmdev->regmap, tmdev->chip->temp_data_base +
+		    0x4 * s->id, &val);
+
+	*temp = sun8i_ths_reg2temp(tmdev, val);
+	/*
+	 * XX - According to the original sdk, there are some platforms(rarely)
+	 * that add a fixed offset value after calculating the temperature
+	 * value. We can't simply put it on the formula for calculating the
+	 * temperature above, because the formula for calculating the
+	 * temperature above is also used when the sensor is calibrated. If
+	 * do this, the correct calibration formula is hard to know.
+	 */
+	if (tmdev->chip->ft_deviation)
+		*temp += tmdev->chip->ft_deviation;
+
+	return 0;
+}
+
+static const struct thermal_zone_of_device_ops ths_ops = {
+	.get_temp = sun8i_ths_get_temp,
+};
+
+static const struct regmap_config config = {
+	.reg_bits = 32,
+	.val_bits = 32,
+	.reg_stride = 4,
+	.fast_io = true,
+};
+
+static irqreturn_t sun50i_h6_irq_thread(int irq, void *data)
+{
+	wait_queue_head_t *data_wait;
+	struct ths_device *tmdev = data;
+	int i, state;
+
+	regmap_read(tmdev->regmap, SUN50I_H6_THS_DIS, &state);
+
+	for (i = 0; i < tmdev->chip->sensor_num; i++) {
+		data_wait = &tmdev->sensor[i].wait_queue;
+
+		if (state & SUN50I_H6_THS_DATA_IRQ_STS(i)) {
+			/* clear data irq pending */
+			regmap_write(tmdev->regmap, SUN50I_H6_THS_DIS,
+				     SUN50I_H6_THS_DATA_IRQ_STS(i));
+
+			tmdev->data_ready |= BIT(i);
+			wake_up(data_wait);
+		}
+	}
+
+	return IRQ_HANDLED;
+}
+
+static int sun8i_ths_resource_init(struct ths_device *tmdev)
+{
+	struct device *dev = tmdev->dev;
+	struct platform_device *pdev = to_platform_device(dev);
+	struct resource *mem;
+	void __iomem *base;
+	int ret, irq;
+
+	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	base = devm_ioremap_resource(dev, mem);
+	if (IS_ERR(base))
+		return PTR_ERR(base);
+
+	tmdev->regmap = devm_regmap_init_mmio(dev, base, &config);
+	if (IS_ERR(tmdev->regmap))
+		return PTR_ERR(tmdev->regmap);
+
+	tmdev->reset = devm_reset_control_get(dev, 0);
+	if (IS_ERR(tmdev->reset))
+		return PTR_ERR(tmdev->reset);
+
+	tmdev->bus_clk = devm_clk_get(&pdev->dev, "bus");
+	if (IS_ERR(tmdev->bus_clk))
+		return PTR_ERR(tmdev->bus_clk);
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0)
+		return irq;
+
+	ret = devm_request_threaded_irq(dev, irq, NULL,
+					tmdev->chip->irq_thread,
+					IRQF_ONESHOT, "ths", tmdev);
+	if (ret)
+		return ret;
+
+	ret = reset_control_deassert(tmdev->reset);
+	if (ret)
+		return ret;
+
+	ret = clk_prepare_enable(tmdev->bus_clk);
+	if (ret)
+		goto assert_reset;
+
+	ret = tmdev->chip->calibrate(tmdev);
+	if (ret)
+		goto bus_disable;
+
+	return 0;
+
+bus_disable:
+	clk_disable_unprepare(tmdev->bus_clk);
+assert_reset:
+	reset_control_assert(tmdev->reset);
+
+	return ret;
+}
+
+static int sun50i_ths_calibrate(struct ths_device *tmdev)
+{
+	struct nvmem_cell *calcell;
+	struct device *dev = tmdev->dev;
+	u16 *caldata;
+	size_t callen;
+	int ft_temp;
+	int i, ret = 0;
+
+	calcell = devm_nvmem_cell_get(dev, "calib");
+	if (IS_ERR(calcell)) {
+		if (PTR_ERR(calcell) == -EPROBE_DEFER)
+			return -EPROBE_DEFER;
+		/*
+		 * Even if the external calibration data stored in sid is
+		 * not accessible, the THS hardware can still work, although
+		 * the data won't be so accurate.
+		 *
+		 * The default value of calibration register is 0x800 for
+		 * every sensor, and the calibration value is usually 0x7xx
+		 * or 0x8xx, so they won't be away from the default value
+		 * for a lot.
+		 *
+		 * So here we do not return error if the calibartion data is
+		 * not available, except the probe needs deferring.
+		 */
+		goto out;
+	}
+
+	caldata = nvmem_cell_read(calcell, &callen);
+	if (IS_ERR(caldata)) {
+		ret = PTR_ERR(caldata);
+		goto out;
+	}
+
+	if (!caldata[0] || callen < 2 + 2 * tmdev->chip->sensor_num) {
+		ret = -EINVAL;
+		goto out_free;
+	}
+
+	/*
+	 * efuse layout:
+	 *
+	 *	0   11  16	 32
+	 *	+-------+-------+-------+
+	 *	|temp|  |sensor0|sensor1|
+	 *	+-------+-------+-------+
+	 *
+	 * The calibration data on the H6 is the ambient temperature and
+	 * sensor values that are filled during the factory test stage.
+	 *
+	 * The unit of stored FT temperature is 0.1 degreee celusis.
+	 * Through the stored ambient temperature and the data read
+	 * by the sensor, after a certain calculation, the calibration
+	 * value to be compensated can be obtained.
+	 */
+	ft_temp = caldata[0] & FT_TEMP_MASK;
+
+	for (i = 0; i < tmdev->chip->sensor_num; i++) {
+		int reg = (int)caldata[i + 1];
+		int sensor_temp = sun8i_ths_reg2temp(tmdev, reg);
+		int delta, cdata, calib_offest;
+
+		/*
+		 * To calculate the calibration value:
+		 *
+		 * X(in Celsius) = Ts - ft_temp
+		 * delta = X * 10000 / TEMP_TO_REG
+		 * cdata = CALIBRATE_DEFAULT - delta
+		 *
+		 * cdata: calibration value
+		 */
+		delta = (sensor_temp - ft_temp * 100) * 10 / TEMP_TO_REG;
+		cdata = CALIBRATE_DEFAULT - delta;
+		if (cdata & ~TEMP_CALIB_MASK) {
+			/*
+			 * Calibration value more than 12-bit, but calibration
+			 * register is 12-bit. In this case, ths hardware can
+			 * still work without calibration, although the data
+			 * won't be so accurate.
+			 */
+			dev_warn(dev, "sensor%d is not calibrated.\n", i);
+
+			continue;
+		}
+
+		calib_offest = tmdev->chip->temp_calib_base + (i / 2) * 0x4;
+
+		if (i % 2) {
+			int val;
+
+			regmap_read(tmdev->regmap, calib_offest, &val);
+			val = (val & TEMP_CALIB_MASK) | (cdata << 16);
+			regmap_write(tmdev->regmap, calib_offest, val);
+		} else {
+			regmap_write(tmdev->regmap, calib_offest, cdata);
+		}
+	}
+
+out_free:
+	kfree(caldata);
+out:
+	return ret;
+}
+
+static int sun8i_ths_register(struct ths_device *tmdev)
+{
+	struct thermal_zone_device *tzd;
+	int i;
+
+	for (i = 0; i < tmdev->chip->sensor_num; i++) {
+		tmdev->sensor[i].tmdev = tmdev;
+		tmdev->sensor[i].id = i;
+		tmdev->sensor[i].tzd =
+			devm_thermal_zone_of_sensor_register(tmdev->dev,
+							     i,
+							     &tmdev->sensor[i],
+							     &ths_ops);
+		if (IS_ERR(tmdev->sensor[i].tzd))
+			return PTR_ERR(tzd);
+	}
+
+	return 0;
+}
+
+static int sun8i_ths_probe(struct platform_device *pdev)
+{
+	struct ths_device *tmdev;
+	struct device *dev = &pdev->dev;
+	int i, ret;
+
+	tmdev = devm_kzalloc(dev, sizeof(*tmdev), GFP_KERNEL);
+	if (!tmdev)
+		return -ENOMEM;
+
+	tmdev->dev = dev;
+	tmdev->chip = of_device_get_match_data(&pdev->dev);
+	if (!tmdev->chip)
+		return -EINVAL;
+
+	/*
+	 * Initialize wait_queue in advance, to avoid calling wake_up
+	 * before ths is registered in isr.
+	 */
+	for (i = 0; i < tmdev->chip->sensor_num; i++)
+		init_waitqueue_head(&tmdev->sensor[i].wait_queue);
+
+	platform_set_drvdata(pdev, tmdev);
+
+	ret = sun8i_ths_resource_init(tmdev);
+	if (ret)
+		return ret;
+
+	ret = tmdev->chip->init(tmdev);
+	if (ret)
+		return ret;
+
+	ret = sun8i_ths_register(tmdev);
+	if (ret)
+		return ret;
+
+	return ret;
+}
+
+static int sun8i_ths_remove(struct platform_device *pdev)
+{
+	struct ths_device *tmdev = platform_get_drvdata(pdev);
+
+	clk_disable_unprepare(tmdev->bus_clk);
+	reset_control_assert(tmdev->reset);
+
+	return 0;
+}
+
+static int sun50i_thermal_init(struct ths_device *tmdev)
+{
+	int val;
+
+	/*
+	 * clkin = 24MHz
+	 * T acquire = clkin / (x + 1)
+	 *           = 20us
+	 */
+	regmap_write(tmdev->regmap, SUN50I_THS_CTRL0,
+		     SUN50I_THS_CTRL0_T_ACQ(479));
+	/* average over 4 samples */
+	regmap_write(tmdev->regmap, SUN50I_H6_THS_MFC,
+		     SUN50I_THS_FILTER_EN |
+		     SUN50I_THS_FILTER_TYPE(1));
+	/* period = (x + 1) * 4096 / clkin; ~10ms */
+	regmap_write(tmdev->regmap, SUN50I_H6_THS_PC,
+		     SUN50I_H6_THS_PC_TEMP_PERIOD(58));
+	/* enable sensor */
+	val = GENMASK(tmdev->chip->sensor_num - 1, 0);
+	regmap_write(tmdev->regmap, SUN50I_H6_THS_ENABLE, val);
+	/* thermal data interrupt enable */
+	val = GENMASK(tmdev->chip->sensor_num - 1, 0);
+	regmap_write(tmdev->regmap, SUN50I_H6_THS_DIC, val);
+
+	return 0;
+}
+
+static const struct ths_thermal_chip sun50i_h6_ths = {
+	.sensor_num = 2,
+	.offset = -2794,
+	.scale = -67,
+	.ft_deviation = SUN50I_H6_FT_DEVIATION,
+	.temp_calib_base = SUN50I_H6_THS_TEMP_CALIB,
+	.temp_data_base = SUN50I_H6_THS_TEMP_DATA,
+	.calibrate = sun50i_ths_calibrate,
+	.init = sun50i_thermal_init,
+	.irq_thread = sun50i_h6_irq_thread,
+};
+
+static const struct of_device_id of_ths_match[] = {
+	{ .compatible = "allwinner,sun50i-h6-ths", .data = &sun50i_h6_ths },
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, of_ths_match);
+
+static struct platform_driver ths_driver = {
+	.probe = sun8i_ths_probe,
+	.remove = sun8i_ths_remove,
+	.driver = {
+		.name = "sun8i-thermal",
+		.of_match_table = of_ths_match,
+	},
+};
+module_platform_driver(ths_driver);
+
+MODULE_DESCRIPTION("Thermal sensor driver for Allwinner SOC");
+MODULE_LICENSE("GPL v2");
-- 
2.17.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

  reply index

Thread overview: 22+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-05-25 18:13 [PATCH v3 0/3] " Yangtao Li
2019-05-25 18:13 ` Yangtao Li [this message]
2019-05-27 12:27   ` [PATCH v3 1/3] thermal: sun8i: " Maxime Ripard
2019-06-07 13:34     ` Frank Lee
2019-06-12 15:43       ` Maxime Ripard
2019-06-13 15:35         ` Frank Lee
2019-06-14  8:02           ` Maxime Ripard
2019-05-27 14:25   ` Ondřej Jirman
2019-06-07 13:50     ` Frank Lee
2019-06-07 13:52       ` Frank Lee
2019-06-07 17:18       ` Ondřej Jirman
2019-06-07 17:25         ` Ondřej Jirman
2019-06-10 23:29   ` Vasily Khoruzhick
2019-06-11  0:31     ` Frank Lee
2019-06-11  0:34       ` Vasily Khoruzhick
2019-06-12 16:49         ` Frank Lee
2019-06-14 23:07           ` Vasily Khoruzhick
2019-06-16 15:27             ` Frank Lee
2019-06-18 19:04             ` Frank Lee
2019-05-25 18:13 ` [PATCH v3 2/3] dt-bindings: thermal: add binding document for h6 thermal controller Yangtao Li
2019-05-27 12:16   ` Maxime Ripard
2019-05-25 18:13 ` [PATCH v3 3/3] thermal: fix indentation in makefile Yangtao Li

Reply instructions:

You may reply publically to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20190525181329.18657-2-tiny.windzz@gmail.com \
    --to=tiny.windzz@gmail.com \
    --cc=daniel.lezcano@linaro.org \
    --cc=davem@davemloft.net \
    --cc=devicetree@vger.kernel.org \
    --cc=edubezval@gmail.com \
    --cc=gregkh@linuxfoundation.org \
    --cc=linus.walleij@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-pm@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=maxime.ripard@bootlin.com \
    --cc=mchehab+samsung@kernel.org \
    --cc=nicolas.ferre@microchip.com \
    --cc=paulmck@linux.ibm.com \
    --cc=robh+dt@kernel.org \
    --cc=rui.zhang@intel.com \
    --cc=wens@csie.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-ARM-Kernel Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-arm-kernel/0 linux-arm-kernel/git/0.git
	git clone --mirror https://lore.kernel.org/linux-arm-kernel/1 linux-arm-kernel/git/1.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-arm-kernel linux-arm-kernel/ https://lore.kernel.org/linux-arm-kernel \
		linux-arm-kernel@lists.infradead.org infradead-linux-arm-kernel@archiver.kernel.org
	public-inbox-index linux-arm-kernel


Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.infradead.lists.linux-arm-kernel


AGPL code for this site: git clone https://public-inbox.org/ public-inbox