Linux-ARM-Kernel Archive on
 help / color / Atom feed
From: "Angus Ainslie (Purism)" <>
Cc: Mark Rutland <>,,,
	Shawn Guo <>,
	Sascha Hauer <>,
	"Angus Ainslie \(Purism\)" <>,, Rob Herring <>,
	NXP Linux Team <>,
	Pengutronix Kernel Team <>,
	Fabio Estevam <>,
Subject: [PATCH v16 0/3] Add support for the Purism Librem5 devkit
Date: Mon, 17 Jun 2019 07:52:12 -0600
Message-ID: <> (raw)

The Librem5 devkit is based on the imx8mq from NXP. This is a default
devicetree to boot the board to a command prompt.

Changes since v15:

Update the ti,minimum-sys-voltage for the PMIC.

Changes since v14:

Add regulator-always-on for the SNVS regulators.
Added pgc nodes.
Fixed charger pre-current.

Changes since v13:

Moved haptic motor from pwm-led to gpio-vibrator.
Cleaned up regulator node naming.
Whitescpace cleanup.
Re-indent pinmux stanzas.
Drop pwm2 node.

Changes since v12:

Updated patch to vendor-prefixes.yaml.
Dropped always on from regulators.

Changes since v11:

Added reviewed-by tags.
Fixed subject typo.

Changes since v10:

Moved MAINTAINERS entry to "ARM/FREESCALE IMX" section

Changes since v9:

Added a MAINTAINERS entry for arm64 imx devicetree files.

Changes since v8:

Fixed license comment.
Changed regulators to all lower case.
Changed clock frequency for NXP errata e7805.
Dropped blank line.

Changes since v7:

More regulators always on for USB.
Add vbus regulator.
Drop vbat regulator.
Replace legacy "gpio-key,wakeup" with "wakeup-source".
Add vbus-supply to get rid of warning
imx8mq-usb-phy 382f0040.usb-phy: 382f0040.usb-phy supply vbus not found,
using dummy regulator

Changes since v6:

Dropped unused regulators.
Fix regulator phandles case.
Dropped extra whitespace.

Changes since v5:

Added reviewed-by tags.
Moved USB port links to USB controller node.

Changes since v4:

Compiled against linux-next next-20190415.
Added imx8mq to the arm yaml file.
Re-arrange regulator nodes to drop undefined supplies.
Additional ordering for aesthetics.
Split some long lines.
Added lots of blank lines.
Moved pinctl muxes to where they are used.
Cleaned out reg defintions from regulator nodes.

Changes since v3:

Freshly sorted and pressed nodes.
Change the backlight to an interpolated scale.
Dropped i2c2.
Dropped devkit version number to match debian MR.

Changes since v2:

Fixed incorrect phy-supply for the fsl-fec.
Dropped unused regulator property.
Fixup Makefile for linux-next.

Changes since v1:

Dropped config file.
Updated the board compatible label.
Changed node names to follow naming conventions.
Added a more complete regulator hierachy.
Removed unused nodes.
Removed unknown devices.
Fixed comment style.
Dropped undocumented properties.

Angus Ainslie (Purism) (3):
  arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit
  dt-bindings: Add an entry for Purism SPC
  dt-bindings: arm: fsl: Add the imx8mq boards

 .../devicetree/bindings/arm/fsl.yaml          |   7 +
 .../devicetree/bindings/vendor-prefixes.yaml  |   2 +
 arch/arm64/boot/dts/freescale/Makefile        |   1 +
 .../dts/freescale/imx8mq-librem5-devkit.dts   | 806 ++++++++++++++++++
 4 files changed, 816 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts


linux-arm-kernel mailing list

             reply index

Thread overview: 7+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-06-17 13:52 Angus Ainslie (Purism) [this message]
2019-06-17 13:52 ` [PATCH v16 1/3] arm64: dts: fsl: librem5: Add a device tree for the " Angus Ainslie (Purism)
2019-06-17 14:01   ` Pavel Machek
2019-06-17 13:52 ` [PATCH v16 2/3] dt-bindings: Add an entry for Purism SPC Angus Ainslie (Purism)
2019-06-17 13:52 ` [PATCH v16 3/3] dt-bindings: arm: fsl: Add the imx8mq boards Angus Ainslie (Purism)
2019-06-18 13:20 ` [PATCH v16 0/3] Add support for the Purism Librem5 devkit Shawn Guo
2019-06-18 13:35   ` Angus Ainslie

Reply instructions:

You may reply publically to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \ \ \ \ \ \ \ \ \ \ \ \ \ \ \

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-ARM-Kernel Archive on

Archives are clonable:
	git clone --mirror linux-arm-kernel/git/0.git
	git clone --mirror linux-arm-kernel/git/1.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-arm-kernel linux-arm-kernel/ \
	public-inbox-index linux-arm-kernel

Newsgroup available over NNTP:

AGPL code for this site: git clone public-inbox