From: Yangtao Li <tiny.windzz@gmail.com>
To: rui.zhang@intel.com, edubezval@gmail.com,
daniel.lezcano@linaro.org, robh+dt@kernel.org,
mark.rutland@arm.com, maxime.ripard@bootlin.com, wens@csie.org,
davem@davemloft.net, gregkh@linuxfoundation.org,
mchehab+samsung@kernel.org, linus.walleij@linaro.org,
nicolas.ferre@microchip.com, paulmck@linux.ibm.com
Cc: Yangtao Li <tiny.windzz@gmail.com>,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org, linux-pm@vger.kernel.org
Subject: [PATCH v4 11/11] thermal: sun8i: add thermal driver for h3
Date: Sun, 23 Jun 2019 12:42:06 -0400 [thread overview]
Message-ID: <20190623164206.7467-12-tiny.windzz@gmail.com> (raw)
In-Reply-To: <20190623164206.7467-1-tiny.windzz@gmail.com>
This patch adds the support for allwinner h3 thermal sensor.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
---
drivers/thermal/sun8i_thermal.c | 72 +++++++++++++++++++++++++++++++++
1 file changed, 72 insertions(+)
diff --git a/drivers/thermal/sun8i_thermal.c b/drivers/thermal/sun8i_thermal.c
index 260b24340f5b..c8ee291f3b17 100644
--- a/drivers/thermal/sun8i_thermal.c
+++ b/drivers/thermal/sun8i_thermal.c
@@ -27,6 +27,14 @@
#define TEMP_TO_REG 672
#define CALIBRATE_DEFAULT 0x800
+#define SUN8I_THS_CTRL0 0x00
+#define SUN8I_THS_CTRL2 0x40
+#define SUN8I_THS_IC 0x44
+#define SUN8I_THS_IS 0x48
+#define SUN8I_THS_MFC 0x70
+#define SUN8I_THS_TEMP_CALIB 0x74
+#define SUN8I_THS_TEMP_DATA 0x80
+
#define SUN50I_THS_CTRL0 0x00
#define SUN50I_H6_THS_ENABLE 0x04
#define SUN50I_H6_THS_PC 0x08
@@ -36,6 +44,9 @@
#define SUN50I_H6_THS_TEMP_CALIB 0xa0
#define SUN50I_H6_THS_TEMP_DATA 0xc0
+#define SUN8I_THS_CTRL0_T_ACQ0(x) (GENMASK(15, 0) & (x))
+#define SUN8I_THS_CTRL2_T_ACQ1(x) ((GENMASK(15, 0) & (x)) << 16)
+
#define SUN50I_THS_CTRL0_T_ACQ(x) ((GENMASK(15, 0) & (x)) << 16)
#define SUN50I_THS_FILTER_EN BIT(2)
#define SUN50I_THS_FILTER_TYPE(x) (GENMASK(1, 0) & (x))
@@ -121,6 +132,21 @@ static const struct regmap_config config = {
.fast_io = true,
};
+static int sun8i_h3_irq_ack(struct ths_device *tmdev)
+{
+ int state, ret = 0;
+
+ regmap_read(tmdev->regmap, SUN8I_THS_IS, &state);
+
+ if (state & BIT(8)) {
+ regmap_write(tmdev->regmap, SUN8I_THS_IS,
+ BIT(8));
+ ret |= BIT(1);
+ }
+
+ return ret;
+}
+
static int sun50i_h6_irq_ack(struct ths_device *tmdev)
{
int i, state, ret = 0;
@@ -154,6 +180,14 @@ static irqreturn_t sun8i_irq_thread(int irq, void *data)
return IRQ_HANDLED;
}
+static int sun8i_h3_ths_calibrate(struct ths_device *tmdev,
+ u16 *caldata, int callen)
+{
+ regmap_write(tmdev->regmap, SUN8I_THS_TEMP_CALIB, *caldata);
+
+ return 0;
+}
+
static int sun50i_h6_ths_calibrate(struct ths_device *tmdev,
u16 *caldata, int callen)
{
@@ -325,6 +359,32 @@ static int sun8i_ths_resource_init(struct ths_device *tmdev)
return ret;
}
+static int sun8i_h3_thermal_init(struct ths_device *tmdev)
+{
+ /* average over 4 samples */
+ regmap_write(tmdev->regmap, SUN8I_THS_MFC,
+ SUN50I_THS_FILTER_EN |
+ SUN50I_THS_FILTER_TYPE(1));
+ /*
+ * period = (x + 1) * 4096 / clkin; ~10ms
+ * enable data interrupt
+ */
+ regmap_write(tmdev->regmap, SUN8I_THS_IC,
+ SUN50I_H6_THS_PC_TEMP_PERIOD(58) | BIT(8));
+ /*
+ * clkin = 24MHz
+ * T acquire = clkin / (x + 1)
+ * = 20us
+ * enable sensor
+ */
+ regmap_write(tmdev->regmap, SUN8I_THS_CTRL0,
+ SUN8I_THS_CTRL0_T_ACQ0(479));
+ regmap_write(tmdev->regmap, SUN8I_THS_CTRL2,
+ SUN8I_THS_CTRL2_T_ACQ1(479) | BIT(0));
+
+ return 0;
+}
+
static int sun50i_thermal_init(struct ths_device *tmdev)
{
int val;
@@ -431,6 +491,17 @@ static int sun8i_ths_remove(struct platform_device *pdev)
return 0;
}
+static const struct ths_thermal_chip sun8i_h3_ths = {
+ .sensor_num = 1,
+ .offset = -1794,
+ .scale = -121,
+ .has_ahb_clk = true,
+ .temp_data_base = SUN8I_THS_TEMP_DATA,
+ .calibrate = sun8i_h3_ths_calibrate,
+ .init = sun8i_h3_thermal_init,
+ .irq_ack = sun8i_h3_irq_ack,
+};
+
static const struct ths_thermal_chip sun50i_h6_ths = {
.sensor_num = 2,
.offset = -2794,
@@ -443,6 +514,7 @@ static const struct ths_thermal_chip sun50i_h6_ths = {
};
static const struct of_device_id of_ths_match[] = {
+ { .compatible = "allwinner,sun8i-h3-ths", .data = &sun8i_h3_ths },
{ .compatible = "allwinner,sun50i-h6-ths", .data = &sun50i_h6_ths },
{ /* sentinel */ },
};
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2019-06-23 16:46 UTC|newest]
Thread overview: 23+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-06-23 16:41 [PATCH v4 00/11] add thermal driver for h6 Yangtao Li
2019-06-23 16:41 ` [PATCH v4 01/11] thermal: sun8i: " Yangtao Li
2019-06-24 12:07 ` Ondřej Jirman
2019-06-23 16:41 ` [PATCH v4 02/11] dt-bindings: thermal: add binding document for h6 thermal controller Yangtao Li
2019-06-24 8:47 ` Maxime Ripard
2019-06-23 16:41 ` [PATCH v4 03/11] thermal: fix indentation in makefile Yangtao Li
2019-06-23 16:41 ` [PATCH v4 04/11] thermal: sun8i: get ths sensor number from device compatible Yangtao Li
2019-06-23 16:42 ` [PATCH v4 05/11] thermal: sun8i: rework for sun8i_ths_get_temp() Yangtao Li
2019-06-23 16:42 ` [PATCH v4 06/11] thermal: sun8i: get ths init func from device compatible Yangtao Li
2019-06-23 16:42 ` [PATCH v4 07/11] thermal: sun8i: rework for ths irq handler func Yangtao Li
2019-06-23 16:42 ` [PATCH v4 08/11] thermal: sun8i: support ahb clocks Yangtao Li
2019-06-24 18:23 ` Maxime Ripard
2019-06-25 0:34 ` Ondřej Jirman
2019-06-25 8:25 ` Maxime Ripard
2019-06-23 16:42 ` [PATCH v4 09/11] thermal: sun8i: rework for ths calibrate func Yangtao Li
2019-06-23 16:42 ` [PATCH v4 10/11] dt-bindings: thermal: add binding document for h3 thermal controller Yangtao Li
2019-06-24 8:50 ` Maxime Ripard
2019-06-23 16:42 ` Yangtao Li [this message]
2019-06-24 12:05 ` [PATCH v4 11/11] thermal: sun8i: add thermal driver for h3 Ondřej Jirman
2019-07-10 23:09 ` [PATCH v4 00/11] add thermal driver for h6 Vasily Khoruzhick
2019-07-13 18:01 ` Vasily Khoruzhick
2019-07-26 17:46 ` Vasily Khoruzhick
2019-07-28 12:11 ` Frank Lee
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190623164206.7467-12-tiny.windzz@gmail.com \
--to=tiny.windzz@gmail.com \
--cc=daniel.lezcano@linaro.org \
--cc=davem@davemloft.net \
--cc=devicetree@vger.kernel.org \
--cc=edubezval@gmail.com \
--cc=gregkh@linuxfoundation.org \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=maxime.ripard@bootlin.com \
--cc=mchehab+samsung@kernel.org \
--cc=nicolas.ferre@microchip.com \
--cc=paulmck@linux.ibm.com \
--cc=robh+dt@kernel.org \
--cc=rui.zhang@intel.com \
--cc=wens@csie.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).