From: Rob Herring <robh@kernel.org>
To: devicetree@vger.kernel.org
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>,
linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
Paul Walmsley <paul.walmsley@sifive.com>
Subject: [PATCH] dt-bindings: arm: Limit cpus schema to only check Arm 'cpu' nodes
Date: Wed, 26 Jun 2019 18:00:44 -0600 [thread overview]
Message-ID: <20190627000044.12739-1-robh@kernel.org> (raw)
Matching on the 'cpus' node was a bad choice because the schema is
incorrectly applied to non-Arm cpus nodes. As we now have a common cpus
schema which checks the general structure, it is also redundant to do so
in the Arm CPU schema.
The downside is one could conceivably mix different architecture's cpu
nodes or have typos in the compatible string. The latter problem pretty
much exists for every schema.
Signed-off-by: Rob Herring <robh@kernel.org>
---
.../devicetree/bindings/arm/cpus.yaml | 500 ++++++++----------
1 file changed, 231 insertions(+), 269 deletions(-)
diff --git a/Documentation/devicetree/bindings/arm/cpus.yaml b/Documentation/devicetree/bindings/arm/cpus.yaml
index 17ac2c642e68..b9c994593537 100644
--- a/Documentation/devicetree/bindings/arm/cpus.yaml
+++ b/Documentation/devicetree/bindings/arm/cpus.yaml
@@ -39,280 +39,242 @@ description: |+
described below.
properties:
- $nodename:
- const: cpus
- description: Container of cpu nodes
-
- '#address-cells':
- enum: [1, 2]
+ reg:
+ maxItems: 1
description: |
- Definition depends on ARM architecture version and configuration:
+ Usage and definition depend on ARM architecture version and
+ configuration:
On uniprocessor ARM architectures previous to v7
- value must be 1, to enable a simple enumeration
- scheme for processors that do not have a HW CPU
- identification register.
- On 32-bit ARM 11 MPcore, ARM v7 or later systems
- value must be 1, that corresponds to CPUID/MPIDR
- registers sizes.
- On ARM v8 64-bit systems value should be set to 2,
- that corresponds to the MPIDR_EL1 register size.
- If MPIDR_EL1[63:32] value is equal to 0 on all CPUs
- in the system, #address-cells can be set to 1, since
- MPIDR_EL1[63:32] bits are not used for CPUs
- identification.
-
- '#size-cells':
- const: 0
-
-patternProperties:
- '^cpu@[0-9a-f]+$':
- type: object
- properties:
- device_type:
- const: cpu
-
- reg:
- maxItems: 1
- description: |
- Usage and definition depend on ARM architecture version and
- configuration:
-
- On uniprocessor ARM architectures previous to v7
- this property is required and must be set to 0.
-
- On ARM 11 MPcore based systems this property is
- required and matches the CPUID[11:0] register bits.
-
- Bits [11:0] in the reg cell must be set to
- bits [11:0] in CPU ID register.
-
- All other bits in the reg cell must be set to 0.
-
- On 32-bit ARM v7 or later systems this property is
- required and matches the CPU MPIDR[23:0] register
- bits.
-
- Bits [23:0] in the reg cell must be set to
- bits [23:0] in MPIDR.
-
- All other bits in the reg cell must be set to 0.
-
- On ARM v8 64-bit systems this property is required
- and matches the MPIDR_EL1 register affinity bits.
-
- * If cpus node's #address-cells property is set to 2
-
- The first reg cell bits [7:0] must be set to
- bits [39:32] of MPIDR_EL1.
-
- The second reg cell bits [23:0] must be set to
- bits [23:0] of MPIDR_EL1.
-
- * If cpus node's #address-cells property is set to 1
-
- The reg cell bits [23:0] must be set to bits [23:0]
- of MPIDR_EL1.
-
- All other bits in the reg cells must be set to 0.
-
- compatible:
- enum:
- - arm,arm710t
- - arm,arm720t
- - arm,arm740t
- - arm,arm7ej-s
- - arm,arm7tdmi
- - arm,arm7tdmi-s
- - arm,arm9es
- - arm,arm9ej-s
- - arm,arm920t
- - arm,arm922t
- - arm,arm925
- - arm,arm926e-s
- - arm,arm926ej-s
- - arm,arm940t
- - arm,arm946e-s
- - arm,arm966e-s
- - arm,arm968e-s
- - arm,arm9tdmi
- - arm,arm1020e
- - arm,arm1020t
- - arm,arm1022e
- - arm,arm1026ej-s
- - arm,arm1136j-s
- - arm,arm1136jf-s
- - arm,arm1156t2-s
- - arm,arm1156t2f-s
- - arm,arm1176jzf
- - arm,arm1176jz-s
- - arm,arm1176jzf-s
- - arm,arm11mpcore
- - arm,armv8 # Only for s/w models
- - arm,cortex-a5
- - arm,cortex-a7
- - arm,cortex-a8
- - arm,cortex-a9
- - arm,cortex-a12
- - arm,cortex-a15
- - arm,cortex-a17
- - arm,cortex-a53
- - arm,cortex-a57
- - arm,cortex-a72
- - arm,cortex-a73
- - arm,cortex-m0
- - arm,cortex-m0+
- - arm,cortex-m1
- - arm,cortex-m3
- - arm,cortex-m4
- - arm,cortex-r4
- - arm,cortex-r5
- - arm,cortex-r7
- - brcm,brahma-b15
- - brcm,brahma-b53
- - brcm,vulcan
- - cavium,thunder
- - cavium,thunder2
- - faraday,fa526
- - intel,sa110
- - intel,sa1100
- - marvell,feroceon
- - marvell,mohawk
- - marvell,pj4a
- - marvell,pj4b
- - marvell,sheeva-v5
- - marvell,sheeva-v7
- - nvidia,tegra132-denver
- - nvidia,tegra186-denver
- - nvidia,tegra194-carmel
- - qcom,krait
- - qcom,kryo
- - qcom,kryo385
- - qcom,scorpion
-
- enable-method:
- allOf:
- - $ref: '/schemas/types.yaml#/definitions/string'
- - oneOf:
- # On ARM v8 64-bit this property is required
- - enum:
- - psci
- - spin-table
- # On ARM 32-bit systems this property is optional
- - enum:
- - actions,s500-smp
- - allwinner,sun6i-a31
- - allwinner,sun8i-a23
- - allwinner,sun9i-a80-smp
- - allwinner,sun8i-a83t-smp
- - amlogic,meson8-smp
- - amlogic,meson8b-smp
- - arm,realview-smp
- - brcm,bcm11351-cpu-method
- - brcm,bcm23550
- - brcm,bcm2836-smp
- - brcm,bcm63138
- - brcm,bcm-nsp-smp
- - brcm,brahma-b15
- - marvell,armada-375-smp
- - marvell,armada-380-smp
- - marvell,armada-390-smp
- - marvell,armada-xp-smp
- - marvell,98dx3236-smp
- - mediatek,mt6589-smp
- - mediatek,mt81xx-tz-smp
- - qcom,gcc-msm8660
- - qcom,kpss-acc-v1
- - qcom,kpss-acc-v2
- - renesas,apmu
- - renesas,r9a06g032-smp
- - rockchip,rk3036-smp
- - rockchip,rk3066-smp
- - socionext,milbeaut-m10v-smp
- - ste,dbx500-smp
-
- cpu-release-addr:
- $ref: '/schemas/types.yaml#/definitions/uint64'
-
- description:
- Required for systems that have an "enable-method"
- property value of "spin-table".
- On ARM v8 64-bit systems must be a two cell
- property identifying a 64-bit zero-initialised
- memory location.
-
- cpu-idle-states:
- $ref: '/schemas/types.yaml#/definitions/phandle-array'
- description: |
- List of phandles to idle state nodes supported
- by this cpu (see ./idle-states.txt).
-
- capacity-dmips-mhz:
- $ref: '/schemas/types.yaml#/definitions/uint32'
- description:
- u32 value representing CPU capacity (see ./cpu-capacity.txt) in
- DMIPS/MHz, relative to highest capacity-dmips-mhz
- in the system.
-
- dynamic-power-coefficient:
- $ref: '/schemas/types.yaml#/definitions/uint32'
- description:
- A u32 value that represents the running time dynamic
- power coefficient in units of uW/MHz/V^2. The
- coefficient can either be calculated from power
- measurements or derived by analysis.
-
- The dynamic power consumption of the CPU is
- proportional to the square of the Voltage (V) and
- the clock frequency (f). The coefficient is used to
- calculate the dynamic power as below -
-
- Pdyn = dynamic-power-coefficient * V^2 * f
-
- where voltage is in V, frequency is in MHz.
-
- qcom,saw:
- $ref: '/schemas/types.yaml#/definitions/phandle'
- description: |
- Specifies the SAW* node associated with this CPU.
-
- Required for systems that have an "enable-method" property
- value of "qcom,kpss-acc-v1" or "qcom,kpss-acc-v2"
-
- * arm/msm/qcom,saw2.txt
-
- qcom,acc:
- $ref: '/schemas/types.yaml#/definitions/phandle'
- description: |
- Specifies the ACC* node associated with this CPU.
-
- Required for systems that have an "enable-method" property
- value of "qcom,kpss-acc-v1" or "qcom,kpss-acc-v2"
-
- * arm/msm/qcom,kpss-acc.txt
-
- rockchip,pmu:
- $ref: '/schemas/types.yaml#/definitions/phandle'
- description: |
- Specifies the syscon node controlling the cpu core power domains.
-
- Optional for systems that have an "enable-method"
- property value of "rockchip,rk3066-smp"
- While optional, it is the preferred way to get access to
- the cpu-core power-domains.
-
- required:
- - device_type
- - reg
- - compatible
-
- dependencies:
- cpu-release-addr: [enable-method]
- rockchip,pmu: [enable-method]
+ this property is required and must be set to 0.
+
+ On ARM 11 MPcore based systems this property is
+ required and matches the CPUID[11:0] register bits.
+
+ Bits [11:0] in the reg cell must be set to
+ bits [11:0] in CPU ID register.
+
+ All other bits in the reg cell must be set to 0.
+
+ On 32-bit ARM v7 or later systems this property is
+ required and matches the CPU MPIDR[23:0] register
+ bits.
+
+ Bits [23:0] in the reg cell must be set to
+ bits [23:0] in MPIDR.
+
+ All other bits in the reg cell must be set to 0.
+
+ On ARM v8 64-bit systems this property is required
+ and matches the MPIDR_EL1 register affinity bits.
+
+ * If cpus node's #address-cells property is set to 2
+
+ The first reg cell bits [7:0] must be set to
+ bits [39:32] of MPIDR_EL1.
+
+ The second reg cell bits [23:0] must be set to
+ bits [23:0] of MPIDR_EL1.
+
+ * If cpus node's #address-cells property is set to 1
+
+ The reg cell bits [23:0] must be set to bits [23:0]
+ of MPIDR_EL1.
+
+ All other bits in the reg cells must be set to 0.
+
+ compatible:
+ enum:
+ - arm,arm710t
+ - arm,arm720t
+ - arm,arm740t
+ - arm,arm7ej-s
+ - arm,arm7tdmi
+ - arm,arm7tdmi-s
+ - arm,arm9es
+ - arm,arm9ej-s
+ - arm,arm920t
+ - arm,arm922t
+ - arm,arm925
+ - arm,arm926e-s
+ - arm,arm926ej-s
+ - arm,arm940t
+ - arm,arm946e-s
+ - arm,arm966e-s
+ - arm,arm968e-s
+ - arm,arm9tdmi
+ - arm,arm1020e
+ - arm,arm1020t
+ - arm,arm1022e
+ - arm,arm1026ej-s
+ - arm,arm1136j-s
+ - arm,arm1136jf-s
+ - arm,arm1156t2-s
+ - arm,arm1156t2f-s
+ - arm,arm1176jzf
+ - arm,arm1176jz-s
+ - arm,arm1176jzf-s
+ - arm,arm11mpcore
+ - arm,armv8 # Only for s/w models
+ - arm,cortex-a5
+ - arm,cortex-a7
+ - arm,cortex-a8
+ - arm,cortex-a9
+ - arm,cortex-a12
+ - arm,cortex-a15
+ - arm,cortex-a17
+ - arm,cortex-a53
+ - arm,cortex-a57
+ - arm,cortex-a72
+ - arm,cortex-a73
+ - arm,cortex-m0
+ - arm,cortex-m0+
+ - arm,cortex-m1
+ - arm,cortex-m3
+ - arm,cortex-m4
+ - arm,cortex-r4
+ - arm,cortex-r5
+ - arm,cortex-r7
+ - brcm,brahma-b15
+ - brcm,brahma-b53
+ - brcm,vulcan
+ - cavium,thunder
+ - cavium,thunder2
+ - faraday,fa526
+ - intel,sa110
+ - intel,sa1100
+ - marvell,feroceon
+ - marvell,mohawk
+ - marvell,pj4a
+ - marvell,pj4b
+ - marvell,sheeva-v5
+ - marvell,sheeva-v7
+ - nvidia,tegra132-denver
+ - nvidia,tegra186-denver
+ - nvidia,tegra194-carmel
+ - qcom,krait
+ - qcom,kryo
+ - qcom,kryo385
+ - qcom,scorpion
+
+ enable-method:
+ allOf:
+ - $ref: '/schemas/types.yaml#/definitions/string'
+ - oneOf:
+ # On ARM v8 64-bit this property is required
+ - enum:
+ - psci
+ - spin-table
+ # On ARM 32-bit systems this property is optional
+ - enum:
+ - actions,s500-smp
+ - allwinner,sun6i-a31
+ - allwinner,sun8i-a23
+ - allwinner,sun9i-a80-smp
+ - allwinner,sun8i-a83t-smp
+ - amlogic,meson8-smp
+ - amlogic,meson8b-smp
+ - arm,realview-smp
+ - brcm,bcm11351-cpu-method
+ - brcm,bcm23550
+ - brcm,bcm2836-smp
+ - brcm,bcm63138
+ - brcm,bcm-nsp-smp
+ - brcm,brahma-b15
+ - marvell,armada-375-smp
+ - marvell,armada-380-smp
+ - marvell,armada-390-smp
+ - marvell,armada-xp-smp
+ - marvell,98dx3236-smp
+ - mediatek,mt6589-smp
+ - mediatek,mt81xx-tz-smp
+ - qcom,gcc-msm8660
+ - qcom,kpss-acc-v1
+ - qcom,kpss-acc-v2
+ - renesas,apmu
+ - renesas,r9a06g032-smp
+ - rockchip,rk3036-smp
+ - rockchip,rk3066-smp
+ - socionext,milbeaut-m10v-smp
+ - ste,dbx500-smp
+
+ cpu-release-addr:
+ $ref: '/schemas/types.yaml#/definitions/uint64'
+
+ description:
+ Required for systems that have an "enable-method"
+ property value of "spin-table".
+ On ARM v8 64-bit systems must be a two cell
+ property identifying a 64-bit zero-initialised
+ memory location.
+
+ cpu-idle-states:
+ $ref: '/schemas/types.yaml#/definitions/phandle-array'
+ description: |
+ List of phandles to idle state nodes supported
+ by this cpu (see ./idle-states.txt).
+
+ capacity-dmips-mhz:
+ $ref: '/schemas/types.yaml#/definitions/uint32'
+ description:
+ u32 value representing CPU capacity (see ./cpu-capacity.txt) in
+ DMIPS/MHz, relative to highest capacity-dmips-mhz
+ in the system.
+
+ dynamic-power-coefficient:
+ $ref: '/schemas/types.yaml#/definitions/uint32'
+ description:
+ A u32 value that represents the running time dynamic
+ power coefficient in units of uW/MHz/V^2. The
+ coefficient can either be calculated from power
+ measurements or derived by analysis.
+
+ The dynamic power consumption of the CPU is
+ proportional to the square of the Voltage (V) and
+ the clock frequency (f). The coefficient is used to
+ calculate the dynamic power as below -
+
+ Pdyn = dynamic-power-coefficient * V^2 * f
+
+ where voltage is in V, frequency is in MHz.
+
+ qcom,saw:
+ $ref: '/schemas/types.yaml#/definitions/phandle'
+ description: |
+ Specifies the SAW* node associated with this CPU.
+
+ Required for systems that have an "enable-method" property
+ value of "qcom,kpss-acc-v1" or "qcom,kpss-acc-v2"
+
+ * arm/msm/qcom,saw2.txt
+
+ qcom,acc:
+ $ref: '/schemas/types.yaml#/definitions/phandle'
+ description: |
+ Specifies the ACC* node associated with this CPU.
+
+ Required for systems that have an "enable-method" property
+ value of "qcom,kpss-acc-v1" or "qcom,kpss-acc-v2"
+
+ * arm/msm/qcom,kpss-acc.txt
+
+ rockchip,pmu:
+ $ref: '/schemas/types.yaml#/definitions/phandle'
+ description: |
+ Specifies the syscon node controlling the cpu core power domains.
+
+ Optional for systems that have an "enable-method"
+ property value of "rockchip,rk3066-smp"
+ While optional, it is the preferred way to get access to
+ the cpu-core power-domains.
required:
- - '#address-cells'
- - '#size-cells'
+ - device_type
+ - reg
+ - compatible
+
+dependencies:
+ rockchip,pmu: [enable-method]
examples:
- |
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next reply other threads:[~2019-06-27 5:30 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-06-27 0:00 Rob Herring [this message]
2019-06-27 1:02 ` [PATCH] dt-bindings: arm: Limit cpus schema to only check Arm 'cpu' nodes Paul Walmsley
2019-06-28 20:32 ` Rob Herring
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190627000044.12739-1-robh@kernel.org \
--to=robh@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=lorenzo.pieralisi@arm.com \
--cc=paul.walmsley@sifive.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).