linux-arm-kernel.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
* [RFC,V2,0/2] media: add support for OV02A10 sensor
@ 2019-07-04  8:46 dongchun.zhu
  2019-07-04  8:46 ` [RFC, V2, 1/2] media: dt-bindings: media: i2c: Add bindings for OV02A10 dongchun.zhu
  2019-07-04  8:46 ` [RFC,V2,2/2] media: i2c: Add Omnivision OV02A10 camera sensor driver dongchun.zhu
  0 siblings, 2 replies; 11+ messages in thread
From: dongchun.zhu @ 2019-07-04  8:46 UTC (permalink / raw)
  To: mchehab, robh+dt, mark.rutland, sakari.ailus, --to=drinkcat,
	tfiga, matthias.bgg, bingbu.cao
  Cc: devicetree, srv_heupstream, shengnan.wang, sj.huang,
	linux-mediatek, dongchun.zhu, louis.kuo, linux-arm-kernel,
	linux-media

From: Dongchun Zhu <dongchun.zhu@mediatek.com>

Hello,

This patch adds driver and bindings for Omnivision's OV02A10 2 megapixel CMOS 1/5" sensor,
which has a single MIPI lane interface and output format of 10-bit Raw.

The driver is implemented wth V4L2 framework.
1. Async registered as a V4L2 I2C sub-device.
2. A media entity that can provide several source pads and sink pads to link with other device like Seninf, ISP one after another
   to create a default overall camera topology, image frame or meta-data from sensor can flow through particular path to output
   preview or capture image or 3A info.

Mainly changes of v2 are addressing the comments from Nicolas, Bingbu, Sakari, Rob,
including,
 - Put dt binding before driver in series
 - Add MAINTAINERS entries
 - Squash the MAINTAINERS entry and Kconfig to driver patch
 - Add rotation support for driver
 - Fix other reviewed issues in v1

Dongchun Zhu (2):
  media: dt-bindings: media: i2c: Add bindings for OV02A10
  media: i2c: Add Omnivision OV02A10 camera sensor driver

 .../devicetree/bindings/media/i2c/ov02a10.txt      |   43 +
 MAINTAINERS                                        |    8 +
 drivers/media/i2c/Kconfig                          |   12 +
 drivers/media/i2c/Makefile                         |    1 +
 drivers/media/i2c/ov02a10.c                        | 1017 ++++++++++++++++++++
 5 files changed, 1081 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/i2c/ov02a10.txt
 create mode 100644 drivers/media/i2c/ov02a10.c

-- 
2.9.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 11+ messages in thread

* [RFC, V2, 1/2] media: dt-bindings: media: i2c: Add bindings for OV02A10
  2019-07-04  8:46 [RFC,V2,0/2] media: add support for OV02A10 sensor dongchun.zhu
@ 2019-07-04  8:46 ` dongchun.zhu
  2019-07-22 23:49   ` [RFC,V2,1/2] " Rob Herring
  2019-07-23  7:41   ` Sakari Ailus
  2019-07-04  8:46 ` [RFC,V2,2/2] media: i2c: Add Omnivision OV02A10 camera sensor driver dongchun.zhu
  1 sibling, 2 replies; 11+ messages in thread
From: dongchun.zhu @ 2019-07-04  8:46 UTC (permalink / raw)
  To: mchehab, robh+dt, mark.rutland, sakari.ailus, --to=drinkcat,
	tfiga, matthias.bgg, bingbu.cao
  Cc: devicetree, srv_heupstream, shengnan.wang, sj.huang,
	linux-mediatek, dongchun.zhu, louis.kuo, linux-arm-kernel,
	linux-media

From: Dongchun Zhu <dongchun.zhu@mediatek.com>

Add device tree binding documentation for the OV02A10 camera sensor.

Signed-off-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
---
 .../devicetree/bindings/media/i2c/ov02a10.txt      | 43 ++++++++++++++++++++++
 MAINTAINERS                                        |  7 ++++
 2 files changed, 50 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/i2c/ov02a10.txt

diff --git a/Documentation/devicetree/bindings/media/i2c/ov02a10.txt b/Documentation/devicetree/bindings/media/i2c/ov02a10.txt
new file mode 100644
index 0000000..d40aa87
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov02a10.txt
@@ -0,0 +1,43 @@
+* Omnivision OV02A10 MIPI CSI-2 sensor
+
+Required Properties:
+- compatible: shall be "ovti,ov02a10"
+- clocks: reference to the xvclk input clock
+- clock-names: shall be "xvclk"
+- avdd-supply: Analog voltage supply, 2.8 volts
+- dovdd-supply: Digital I/O voltage supply, 1.8 volts
+- dvdd-supply: Digital core voltage supply, 1.8 volts
+- reset-gpios: Low active reset gpio
+
+The device node shall contain one 'port' child node with an
+'endpoint' subnode for its digital output video port,
+in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+The endpoint optional property 'data-lanes' shall be "<1>".
+
+Example:
+&i2c4 {
+	ov02a10: camera-sensor@3d {
+		compatible = "ovti,ov02a10";
+		reg = <0x3d>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&camera_pins_cam1_mclk_on>;
+
+		clocks = <&topckgen CLK_TOP_MUX_CAMTG2>,
+			<&topckgen CLK_TOP_UNIVP_192M_D8>;
+		clock-names = "xvclk", "freq_mux";
+
+		avdd-supply = <&mt6358_vcama1_reg>;
+		dvdd-supply = <&mt6358_vcn18_reg>;
+		dovdd-supply = <&mt6358_vcamio_reg>;
+		pwdn-gpios = <&pio 107 1>;
+		reset-gpios = <&pio 109 1>;
+
+		port {
+		   ov02a10_core: endpoint {
+		       remote-endpoint = <&ov02a10_0>;
+			   data-lanes = <1>;
+			};
+		};
+	};
+};
diff --git a/MAINTAINERS b/MAINTAINERS
index 5cfbea4..62b81ff 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -11571,6 +11571,13 @@ T:	git git://linuxtv.org/media_tree.git
 S:	Maintained
 F:	drivers/media/i2c/ov13858.c
 
+OMNIVISION OV02A10 SENSOR DRIVER
+M:	Dongchun Zhu <dongchun.zhu@mediatek.com>
+L:	linux-media@vger.kernel.org
+T:	git git://linuxtv.org/media_tree.git
+S:	Maintained
+F:	Documentation/devicetree/bindings/media/i2c/ov02a10.txt
+
 OMNIVISION OV2680 SENSOR DRIVER
 M:	Rui Miguel Silva <rmfrfs@gmail.com>
 L:	linux-media@vger.kernel.org
-- 
2.9.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply related	[flat|nested] 11+ messages in thread

* [RFC,V2,2/2] media: i2c: Add Omnivision OV02A10 camera sensor driver
  2019-07-04  8:46 [RFC,V2,0/2] media: add support for OV02A10 sensor dongchun.zhu
  2019-07-04  8:46 ` [RFC, V2, 1/2] media: dt-bindings: media: i2c: Add bindings for OV02A10 dongchun.zhu
@ 2019-07-04  8:46 ` dongchun.zhu
  2019-07-08  7:52   ` Bingbu Cao
  1 sibling, 1 reply; 11+ messages in thread
From: dongchun.zhu @ 2019-07-04  8:46 UTC (permalink / raw)
  To: mchehab, robh+dt, mark.rutland, sakari.ailus, --to=drinkcat,
	tfiga, matthias.bgg, bingbu.cao
  Cc: devicetree, srv_heupstream, shengnan.wang, sj.huang,
	linux-mediatek, dongchun.zhu, louis.kuo, linux-arm-kernel,
	linux-media

From: Dongchun Zhu <dongchun.zhu@mediatek.com>

This patch adds a V4L2 sub-device driver for OV02A10 image sensor.
The OV02A10 is a 1/5" CMOS sensor from Omnivision.
Supports output format: 10-bit Raw.
The OV02A10 has a single MIPI lane interface and use the I2C bus for control and the CSI-2 bus for data.

Signed-off-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
---
 MAINTAINERS                 |    1 +
 drivers/media/i2c/Kconfig   |   12 +
 drivers/media/i2c/Makefile  |    1 +
 drivers/media/i2c/ov02a10.c | 1017 +++++++++++++++++++++++++++++++++++++++++++
 4 files changed, 1031 insertions(+)
 create mode 100644 drivers/media/i2c/ov02a10.c

diff --git a/MAINTAINERS b/MAINTAINERS
index 62b81ff..863aaab 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -11576,6 +11576,7 @@ M:	Dongchun Zhu <dongchun.zhu@mediatek.com>
 L:	linux-media@vger.kernel.org
 T:	git git://linuxtv.org/media_tree.git
 S:	Maintained
+F:	drivers/media/i2c/ov02a10.c
 F:	Documentation/devicetree/bindings/media/i2c/ov02a10.txt
 
 OMNIVISION OV2680 SENSOR DRIVER
diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
index 7793358..480aa42 100644
--- a/drivers/media/i2c/Kconfig
+++ b/drivers/media/i2c/Kconfig
@@ -615,6 +615,18 @@ config VIDEO_IMX355
 	  To compile this driver as a module, choose M here: the
 	  module will be called imx355.
 
+config VIDEO_OV02A10
+	tristate "OmniVision OV02A10 sensor support"
+	depends on I2C && VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API
+	depends on MEDIA_CAMERA_SUPPORT
+	select V4L2_FWNODE
+	help
+	  This is a Video4Linux2 sensor driver for the OmniVision
+	  OV02A10 camera.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called ov02a10.
+
 config VIDEO_OV2640
 	tristate "OmniVision OV2640 sensor support"
 	depends on VIDEO_V4L2 && I2C
diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
index d8ad9da..4b8f67b 100644
--- a/drivers/media/i2c/Makefile
+++ b/drivers/media/i2c/Makefile
@@ -63,6 +63,7 @@ obj-$(CONFIG_VIDEO_VP27SMPX) += vp27smpx.o
 obj-$(CONFIG_VIDEO_SONY_BTF_MPX) += sony-btf-mpx.o
 obj-$(CONFIG_VIDEO_UPD64031A) += upd64031a.o
 obj-$(CONFIG_VIDEO_UPD64083) += upd64083.o
+obj-$(CONFIG_VIDEO_OV02A10) += ov02a10.o
 obj-$(CONFIG_VIDEO_OV2640) += ov2640.o
 obj-$(CONFIG_VIDEO_OV2680) += ov2680.o
 obj-$(CONFIG_VIDEO_OV2685) += ov2685.o
diff --git a/drivers/media/i2c/ov02a10.c b/drivers/media/i2c/ov02a10.c
new file mode 100644
index 0000000..afd6063
--- /dev/null
+++ b/drivers/media/i2c/ov02a10.c
@@ -0,0 +1,1017 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2018 MediaTek Inc.
+ */
+
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/pm_runtime.h>
+#include <linux/regulator/consumer.h>
+#include <media/media-entity.h>
+#include <media/v4l2-async.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-subdev.h>
+
+#define CHIP_ID                                         0x2509
+#define OV02A10_REG_CHIP_ID_H                           0x02
+#define OV02A10_REG_CHIP_ID_L                           0x03
+#define OV02A10_ID(_msb, _lsb)                          ((_msb) << 8 | (_lsb))
+
+/* bit[1] vertical upside down */
+/* bit[0] horizontal mirror */
+#define REG_MIRROR_FLIP_CONTROL                         0x3f
+
+/* Orientation */
+#define REG_CONFIG_MIRROR_FLIP                          0x03
+
+#define REG_PAGE_SWITCH                                 0xfd
+#define REG_GLOBAL_EFFECTIVE                            0x01
+#define REG_ENABLE                                      BIT(0)
+
+#define REG_SC_CTRL_MODE                                0xac
+#define SC_CTRL_MODE_STANDBY                            0x00
+#define SC_CTRL_MODE_STREAMING                          0x01
+
+#define OV02A10_REG_EXPOSURE_H                          0x03
+#define OV02A10_REG_EXPOSURE_L                          0x04
+#define	OV02A10_EXPOSURE_MIN                            4
+#define	OV02A10_EXPOSURE_STEP                           1
+
+#define OV02A10_REG_VTS_H                               0x05
+#define OV02A10_REG_VTS_L                               0x06
+#define OV02A10_VTS_MAX                                 0x209f
+#define OV02A10_VTS_MIN                                 0x04cf
+
+#define OV02A10_REG_GAIN                                0x24
+#define OV02A10_GAIN_MIN                                0x10
+#define OV02A10_GAIN_MAX                                0xf8
+#define OV02A10_GAIN_STEP                               0x01
+#define OV02A10_GAIN_DEFAULT                            0x40
+
+#define REG_NULL                                        0xff
+
+#define OV02A10_LANES                                   1
+#define OV02A10_BITS_PER_SAMPLE                         10
+
+static const char * const ov02a10_supply_names[] = {
+	"dovdd",	/* Digital I/O power */
+	"avdd",		/* Analog power */
+	"dvdd",		/* Digital core power */
+};
+
+#define OV02A10_NUM_SUPPLIES ARRAY_SIZE(ov02a10_supply_names)
+
+struct regval {
+	u16 addr;
+	u8 val;
+};
+
+struct ov02a10_mode {
+	u32 width;
+	u32 height;
+	u32 exp_def;
+	u32 hts_def;
+	u32 vts_def;
+	const struct regval *reg_list;
+};
+
+struct ov02a10 {
+	struct clk		*xvclk;
+	struct gpio_desc	*pwdn_gpio;
+	struct gpio_desc	*reset_gpio;
+	struct regulator_bulk_data supplies[OV02A10_NUM_SUPPLIES];
+
+	bool			streaming;
+	bool			upside_down;
+
+	/*
+	 * Serialize control access, get/set format, get selection
+	 * and start streaming.
+	 */
+	struct mutex		mutex;
+	struct v4l2_subdev	subdev;
+	struct media_pad	pad;
+	struct v4l2_ctrl	*anal_gain;
+	struct v4l2_ctrl	*exposure;
+	struct v4l2_ctrl	*hblank;
+	struct v4l2_ctrl	*vblank;
+	struct v4l2_ctrl	*hflip;
+	struct v4l2_ctrl	*vflip;
+	struct v4l2_ctrl	*test_pattern;
+	struct v4l2_mbus_framefmt	fmt;
+	struct v4l2_ctrl_handler ctrl_handler;
+
+	const struct ov02a10_mode *cur_mode;
+};
+
+#define to_ov02a10(sd) container_of(sd, struct ov02a10, subdev)
+
+static inline void msleep_range(unsigned int delay_base)
+{
+	usleep_range(delay_base * 1000, delay_base * 1000 + 500);
+}
+
+/* MIPI color bar enable output */
+static const struct regval ov02a10_test_pattern_enable_regs[] = {
+	{0xfd, 0x01},
+	{0x0d, 0x00},
+	{0xb6, 0x01},
+	{0x01, 0x01},
+	{0xfd, 0x01},
+	{0xac, 0x01},
+	{REG_NULL, 0x00}
+};
+
+/* MIPI color bar disable output */
+static const struct regval ov02a10_test_pattern_disable_regs[] = {
+	{0xfd, 0x01},
+	{0x0d, 0x00},
+	{0xb6, 0x00},
+	{0x01, 0x01},
+	{0xfd, 0x01},
+	{0xac, 0x01},
+	{REG_NULL, 0x00}
+};
+
+/*
+ * Xclk 24Mhz
+ * Pclk 39Mhz
+ * linelength 934(0x3a6)
+ * framelength 1390(0x56E)
+ * grabwindow_width 1600
+ * grabwindow_height 1200
+ * max_framerate 30fps
+ * mipi_datarate per lane 780Mbps
+ */
+static const struct regval ov02a10_1600x1200_regs[] = {
+	{0xfd, 0x01},
+	{0xac, 0x00},
+	{0xfd, 0x00},
+	{0x2f, 0x29},
+	{0x34, 0x00},
+	{0x35, 0x21},
+	{0x30, 0x15},
+	{0x33, 0x01},
+	{0xfd, 0x01},
+	{0x44, 0x00},
+	{0x2a, 0x4c},
+	{0x2b, 0x1e},
+	{0x2c, 0x60},
+	{0x25, 0x11},
+	{0x03, 0x01},
+	{0x04, 0xae},
+	{0x09, 0x00},
+	{0x0a, 0x02},
+	{0x06, 0xa6},
+	{0x31, 0x00},
+	{0x24, 0x40},
+	{0x01, 0x01},
+	{0xfb, 0x73},
+	{0xfd, 0x01},
+	{0x16, 0x04},
+	{0x1c, 0x09},
+	{0x21, 0x42},
+	{0x12, 0x04},
+	{0x13, 0x10},
+	{0x11, 0x40},
+	{0x33, 0x81},
+	{0xd0, 0x00},
+	{0xd1, 0x01},
+	{0xd2, 0x00},
+	{0x50, 0x10},
+	{0x51, 0x23},
+	{0x52, 0x20},
+	{0x53, 0x10},
+	{0x54, 0x02},
+	{0x55, 0x20},
+	{0x56, 0x02},
+	{0x58, 0x48},
+	{0x5d, 0x15},
+	{0x5e, 0x05},
+	{0x66, 0x66},
+	{0x68, 0x68},
+	{0x6b, 0x00},
+	{0x6c, 0x00},
+	{0x6f, 0x40},
+	{0x70, 0x40},
+	{0x71, 0x0a},
+	{0x72, 0xf0},
+	{0x73, 0x10},
+	{0x75, 0x80},
+	{0x76, 0x10},
+	{0x84, 0x00},
+	{0x85, 0x10},
+	{0x86, 0x10},
+	{0x87, 0x00},
+	{0x8a, 0x22},
+	{0x8b, 0x22},
+	{0x19, 0xf1},
+	{0x29, 0x01},
+	{0xfd, 0x01},
+	{0x9d, 0xd6},
+	{0xa0, 0x29},
+	{0xa1, 0x03},
+	{0xad, 0x62},
+	{0xae, 0x00},
+	{0xaf, 0x85},
+	{0xb1, 0x01},
+	{0x8e, 0x06},
+	{0x8f, 0x40},
+	{0x90, 0x04},
+	{0x91, 0xb0},
+	{0x45, 0x01},
+	{0x46, 0x00},
+	{0x47, 0x6c},
+	{0x48, 0x03},
+	{0x49, 0x8b},
+	{0x4a, 0x00},
+	{0x4b, 0x07},
+	{0x4c, 0x04},
+	{0x4d, 0xb7},
+	{0xf0, 0x40},
+	{0xf1, 0x40},
+	{0xf2, 0x40},
+	{0xf3, 0x40},
+	{0x3f, 0x00},
+	{0xfd, 0x01},
+	{0x05, 0x00},
+	{0x06, 0xa6},
+	{0xfd, 0x01},
+	{REG_NULL, 0x00}
+};
+
+#define OV02A10_LINK_FREQ_390MHZ		390000000
+static const s64 link_freq_menu_items[] = {
+	OV02A10_LINK_FREQ_390MHZ
+};
+
+static const char * const ov02a10_test_pattern_menu[] = {
+	"Disabled",
+	"Color Bar",
+};
+
+static const struct ov02a10_mode supported_modes[] = {
+	{
+		.width = 1600,
+		.height = 1200,
+		.exp_def = 0x01ae,
+		.hts_def = 0x03a6,
+		.vts_def = 0x056e,
+		.reg_list = ov02a10_1600x1200_regs,
+	},
+};
+
+/* write a register */
+static int ov02a10_write_reg(struct ov02a10 *ov02a10, u8 addr, u8 val)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
+	u8 buf[2] = {addr, val};
+	int ret;
+
+	ret = i2c_master_send(client, buf, 2);
+
+	if (ret != 2) {
+		dev_err(&client->dev, "%s: error: reg=%x, val=%x\n",
+			__func__, addr, val);
+		return -EIO;
+	}
+
+	return 0;
+}
+
+static int ov02a10_write_array(struct ov02a10 *ov02a10,
+			       const struct regval *regs)
+{
+	u32 i;
+	int ret;
+
+	for (i = 0; regs[i].addr != REG_NULL; i++) {
+		ret = ov02a10_write_reg(ov02a10, regs[i].addr, regs[i].val);
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+
+/* read a register */
+static int ov02a10_read_reg(struct ov02a10 *ov02a10, u8 reg, u8 *val)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
+	u8 data = reg;
+	struct i2c_msg msg = {
+		.addr	= client->addr,
+		.flags	= 0,
+		.len	= 1,
+		.buf	= &data,
+	};
+	int ret;
+
+	ret = i2c_transfer(client->adapter, &msg, 1);
+	if (ret < 0)
+		goto err_wr;
+
+	msg.flags = I2C_M_RD;
+	ret = i2c_transfer(client->adapter, &msg, 1);
+	if (ret < 0)
+		goto err_rd;
+
+	*val = data;
+	return 0;
+
+err_rd:
+	dev_err(&client->dev, "i2c_transfer --I2C_M_RD failed\n");
+err_wr:
+	dev_err(&client->dev, "read error: reg=0x%02x: %d\n", reg, ret);
+	return ret;
+}
+
+static void ov02a10_fill_fmt(const struct ov02a10_mode *mode,
+			     struct v4l2_mbus_framefmt *fmt)
+{
+	fmt->width = mode->width;
+	fmt->height = mode->height;
+	fmt->field = V4L2_FIELD_NONE;
+}
+
+static int ov02a10_set_fmt(struct v4l2_subdev *sd,
+			   struct v4l2_subdev_pad_config *cfg,
+			   struct v4l2_subdev_format *fmt)
+{
+	struct ov02a10 *ov02a10 = to_ov02a10(sd);
+	struct v4l2_mbus_framefmt *mbus_fmt = &fmt->format;
+	int ret = 0;
+
+	mutex_lock(&ov02a10->mutex);
+
+	if (ov02a10->streaming) {
+		ret = -EBUSY;
+		goto unlock;
+	}
+
+	/* only one mode supported */
+	mbus_fmt->code = ov02a10->fmt.code;
+	ov02a10_fill_fmt(ov02a10->cur_mode, mbus_fmt);
+	ov02a10->fmt = fmt->format;
+
+unlock:
+	mutex_unlock(&ov02a10->mutex);
+
+	return ret;
+}
+
+static int ov02a10_get_fmt(struct v4l2_subdev *sd,
+			   struct v4l2_subdev_pad_config *cfg,
+			   struct v4l2_subdev_format *fmt)
+{
+	struct ov02a10 *ov02a10 = to_ov02a10(sd);
+	struct v4l2_mbus_framefmt *mbus_fmt = &fmt->format;
+
+	mutex_lock(&ov02a10->mutex);
+
+	fmt->format = ov02a10->fmt;
+	mbus_fmt->code = ov02a10->fmt.code;
+	ov02a10_fill_fmt(ov02a10->cur_mode, mbus_fmt);
+
+	mutex_unlock(&ov02a10->mutex);
+
+	return 0;
+}
+
+static int ov02a10_enum_mbus_code(struct v4l2_subdev *sd,
+				  struct v4l2_subdev_pad_config *cfg,
+				  struct v4l2_subdev_mbus_code_enum *code)
+{
+	struct ov02a10 *ov02a10 = to_ov02a10(sd);
+
+	if (code->index >= ARRAY_SIZE(supported_modes) || !(code->index))
+		return -EINVAL;
+
+	code->code = ov02a10->fmt.code;
+
+	return 0;
+}
+
+static int ov02a10_enum_frame_sizes(struct v4l2_subdev *sd,
+				    struct v4l2_subdev_pad_config *cfg,
+				    struct v4l2_subdev_frame_size_enum *fse)
+{
+	if (fse->index >= ARRAY_SIZE(supported_modes) || !(fse->index))
+		return -EINVAL;
+
+	fse->min_width  = supported_modes[fse->index].width;
+	fse->max_width  = supported_modes[fse->index].width;
+	fse->max_height = supported_modes[fse->index].height;
+	fse->min_height = supported_modes[fse->index].height;
+
+	return 0;
+}
+
+static int __ov02a10_power_on(struct ov02a10 *ov02a10)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
+	struct device *dev = &client->dev;
+	int ret;
+
+	ret = clk_prepare_enable(ov02a10->xvclk);
+	if (ret < 0) {
+		dev_err(dev, "Failed to enable xvclk\n");
+		return ret;
+	}
+
+	/* note: set 0 is high, set 1 is low */
+	gpiod_set_value_cansleep(ov02a10->reset_gpio, 1);
+	gpiod_set_value_cansleep(ov02a10->pwdn_gpio, 0);
+
+	ret = regulator_bulk_enable(OV02A10_NUM_SUPPLIES, ov02a10->supplies);
+	if (ret < 0) {
+		dev_err(dev, "Failed to enable regulators\n");
+		goto disable_clk;
+	}
+	msleep_range(7);
+
+	gpiod_set_value_cansleep(ov02a10->pwdn_gpio, 1);
+	msleep_range(10);
+
+	gpiod_set_value_cansleep(ov02a10->reset_gpio, 0);
+	msleep_range(10);
+
+	return 0;
+
+disable_clk:
+	clk_disable_unprepare(ov02a10->xvclk);
+
+	return ret;
+}
+
+static void __ov02a10_power_off(struct ov02a10 *ov02a10)
+{
+	clk_disable_unprepare(ov02a10->xvclk);
+	gpiod_set_value_cansleep(ov02a10->reset_gpio, 1);
+	gpiod_set_value_cansleep(ov02a10->pwdn_gpio, 1);
+	regulator_bulk_disable(OV02A10_NUM_SUPPLIES, ov02a10->supplies);
+}
+
+static int __ov02a10_start_stream(struct ov02a10 *ov02a10)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
+	int ret;
+
+	/* Apply default values of current mode */
+	ret = ov02a10_write_array(ov02a10, ov02a10->cur_mode->reg_list);
+	if (ret)
+		return ret;
+
+	/* Apply customized values from user */
+	ret = __v4l2_ctrl_handler_setup(ov02a10->subdev.ctrl_handler);
+	if (ret)
+		return ret;
+
+	/* Set Orientation be 180 degree */
+	if (ov02a10->upside_down) {
+		ret = ov02a10_write_reg(ov02a10, REG_MIRROR_FLIP_CONTROL,
+					REG_CONFIG_MIRROR_FLIP);
+		if (ret) {
+			dev_err(&client->dev, "%s failed to set orientation\n",
+				__func__);
+			return ret;
+		}
+		ret = ov02a10_write_reg(ov02a10, REG_GLOBAL_EFFECTIVE,
+					REG_ENABLE);
+		if (ret < 0)
+			return ret;
+	}
+
+	/* set stream on register */
+	return ov02a10_write_reg(ov02a10,
+				 REG_SC_CTRL_MODE, SC_CTRL_MODE_STREAMING);
+}
+
+static int __ov02a10_stop_stream(struct ov02a10 *ov02a10)
+{
+	return ov02a10_write_reg(ov02a10,
+				 REG_SC_CTRL_MODE, SC_CTRL_MODE_STANDBY);
+}
+
+static int ov02a10_entity_init_cfg(struct v4l2_subdev *subdev,
+				   struct v4l2_subdev_pad_config *cfg)
+{
+	struct v4l2_subdev_format fmt = { 0 };
+
+	fmt.which = cfg ? V4L2_SUBDEV_FORMAT_TRY : V4L2_SUBDEV_FORMAT_ACTIVE;
+	fmt.format.width = 1600;
+	fmt.format.height = 1200;
+
+	ov02a10_set_fmt(subdev, cfg, &fmt);
+
+	return 0;
+}
+
+static int ov02a10_s_stream(struct v4l2_subdev *sd, int on)
+{
+	struct ov02a10 *ov02a10 = to_ov02a10(sd);
+	struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
+	int ret = 0;
+
+	dev_dbg(&client->dev, "ov02a10 s_stream (%d)\n", on);
+	mutex_lock(&ov02a10->mutex);
+
+	if (ov02a10->streaming == on)
+		goto unlock_and_return;
+
+	if (on) {
+		ret = pm_runtime_get_sync(&client->dev);
+		if (ret < 0) {
+			pm_runtime_put_noidle(&client->dev);
+			goto unlock_and_return;
+		}
+
+		ret = __ov02a10_start_stream(ov02a10);
+		if (ret) {
+			__ov02a10_stop_stream(ov02a10);
+			ov02a10->streaming = !on;
+			goto err_rpm_put;
+		}
+	} else {
+		__ov02a10_stop_stream(ov02a10);
+		pm_runtime_put(&client->dev);
+	}
+
+	ov02a10->streaming = on;
+	mutex_unlock(&ov02a10->mutex);
+
+	return ret;
+
+err_rpm_put:
+	pm_runtime_put(&client->dev);
+unlock_and_return:
+	mutex_unlock(&ov02a10->mutex);
+
+	return ret;
+}
+
+static int ov02a10_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh)
+{
+	struct ov02a10 *ov02a10 = to_ov02a10(sd);
+	struct v4l2_mbus_framefmt *try_fmt = v4l2_subdev_get_try_format(sd,
+									fh->pad,
+									0);
+
+	mutex_lock(&ov02a10->mutex);
+	/* Initialize try_fmt */
+	try_fmt->code = ov02a10->fmt.code;
+	ov02a10_fill_fmt(&supported_modes[0], try_fmt);
+
+	mutex_unlock(&ov02a10->mutex);
+
+	return 0;
+}
+
+static int __maybe_unused ov02a10_runtime_resume(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct v4l2_subdev *sd = i2c_get_clientdata(client);
+	struct ov02a10 *ov02a10 = to_ov02a10(sd);
+
+	return __ov02a10_power_on(ov02a10);
+}
+
+static int __maybe_unused ov02a10_runtime_suspend(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct v4l2_subdev *sd = i2c_get_clientdata(client);
+	struct ov02a10 *ov02a10 = to_ov02a10(sd);
+
+	__ov02a10_power_off(ov02a10);
+
+	return 0;
+}
+
+static const struct dev_pm_ops ov02a10_pm_ops = {
+	SET_RUNTIME_PM_OPS(ov02a10_runtime_suspend,
+			   ov02a10_runtime_resume, NULL)
+};
+
+static int ov02a10_set_test_pattern(struct ov02a10 *ov02a10, s32 value)
+{
+	if (value)
+		return ov02a10_write_array(ov02a10,
+					   ov02a10_test_pattern_enable_regs);
+
+	return ov02a10_write_array(ov02a10,
+		ov02a10_test_pattern_disable_regs);
+}
+
+static int ov02a10_set_ctrl(struct v4l2_ctrl *ctrl)
+{
+	struct ov02a10 *ov02a10 = container_of(ctrl->handler,
+					     struct ov02a10, ctrl_handler);
+	struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
+	s64 max_expo;
+	int ret;
+
+	/* Propagate change of current control to all related controls */
+	if (ctrl->id == V4L2_CID_VBLANK) {
+		/* Update max exposure while meeting expected vblanking */
+		max_expo = ov02a10->cur_mode->height + ctrl->val - 4;
+		__v4l2_ctrl_modify_range(ov02a10->exposure,
+					 ov02a10->exposure->minimum, max_expo,
+					 ov02a10->exposure->step,
+					 ov02a10->exposure->default_value);
+	}
+
+	/* V4L2 controls values will be applied only when power is already up */
+	if (!pm_runtime_get_if_in_use(&client->dev))
+		return 0;
+
+	switch (ctrl->id) {
+	case V4L2_CID_EXPOSURE:
+		ret = ov02a10_write_reg(ov02a10, REG_PAGE_SWITCH, REG_ENABLE);
+		if (ret < 0)
+			return ret;
+		ret = ov02a10_write_reg(ov02a10, OV02A10_REG_EXPOSURE_H,
+					((ctrl->val >> 8) & 0xFF));
+		if (!ret) {
+			ret = ov02a10_write_reg(ov02a10, OV02A10_REG_EXPOSURE_L,
+						(ctrl->val & 0xFF));
+			if (ret < 0)
+				return ret;
+		}
+		ret = ov02a10_write_reg(ov02a10, REG_GLOBAL_EFFECTIVE,
+					REG_ENABLE);
+		if (ret < 0)
+			return ret;
+		break;
+	case V4L2_CID_ANALOGUE_GAIN:
+		ret = ov02a10_write_reg(ov02a10, REG_PAGE_SWITCH, REG_ENABLE);
+		if (ret < 0)
+			return ret;
+		ret = ov02a10_write_reg(ov02a10, OV02A10_REG_GAIN,
+					(ctrl->val & 0xFF));
+		if (ret < 0)
+			return ret;
+		ret = ov02a10_write_reg(ov02a10, REG_GLOBAL_EFFECTIVE,
+					REG_ENABLE);
+		if (ret < 0)
+			return ret;
+		break;
+	case V4L2_CID_VBLANK:
+		ret = ov02a10_write_reg(ov02a10, REG_PAGE_SWITCH, REG_ENABLE);
+		if (ret < 0)
+			return ret;
+		ret = ov02a10_write_reg(ov02a10, OV02A10_REG_VTS_H,
+					(((ctrl->val +
+					ov02a10->cur_mode->height - 1224) >> 8)
+					& 0xFF));
+		if (!ret) {
+			ret = ov02a10_write_reg(ov02a10, OV02A10_REG_VTS_L,
+						((ctrl->val +
+						ov02a10->cur_mode->height -
+						1224) & 0xFF));
+			if (ret < 0)
+				return ret;
+		}
+		ret = ov02a10_write_reg(ov02a10, REG_GLOBAL_EFFECTIVE,
+					REG_ENABLE);
+		if (ret < 0)
+			return ret;
+		break;
+	case V4L2_CID_TEST_PATTERN:
+		ret = ov02a10_set_test_pattern(ov02a10, ctrl->val);
+		if (ret < 0)
+			return ret;
+		break;
+	default:
+		dev_warn(&client->dev, "%s Unhandled id:0x%x, val:0x%x\n",
+			 __func__, ctrl->id, ctrl->val);
+		ret = -EINVAL;
+		break;
+	};
+
+	pm_runtime_put(&client->dev);
+
+	return ret;
+}
+
+static const struct v4l2_subdev_video_ops ov02a10_video_ops = {
+	.s_stream = ov02a10_s_stream,
+};
+
+static const struct v4l2_subdev_pad_ops ov02a10_pad_ops = {
+	.init_cfg = ov02a10_entity_init_cfg,
+	.enum_mbus_code = ov02a10_enum_mbus_code,
+	.enum_frame_size = ov02a10_enum_frame_sizes,
+	.get_fmt = ov02a10_get_fmt,
+	.set_fmt = ov02a10_set_fmt,
+};
+
+static const struct v4l2_subdev_ops ov02a10_subdev_ops = {
+	.video	= &ov02a10_video_ops,
+	.pad	= &ov02a10_pad_ops,
+};
+
+static const struct media_entity_operations ov02a10_subdev_entity_ops = {
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+static const struct v4l2_subdev_internal_ops ov02a10_internal_ops = {
+	.open = ov02a10_open,
+};
+
+static const struct v4l2_ctrl_ops ov02a10_ctrl_ops = {
+	.s_ctrl = ov02a10_set_ctrl,
+};
+
+static int ov02a10_initialize_controls(struct ov02a10 *ov02a10)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
+	const struct ov02a10_mode *mode;
+	struct v4l2_ctrl_handler *handler;
+	struct v4l2_ctrl *ctrl;
+	u64 exposure_max;
+	u32 pixel_rate, h_blank;
+	int ret;
+
+	handler = &ov02a10->ctrl_handler;
+	mode = ov02a10->cur_mode;
+	ret = v4l2_ctrl_handler_init(handler, 10);
+	if (ret)
+		return ret;
+	handler->lock = &ov02a10->mutex;
+
+	ctrl = v4l2_ctrl_new_int_menu(handler, NULL, V4L2_CID_LINK_FREQ,
+				      0, 0, link_freq_menu_items);
+	if (ctrl)
+		ctrl->flags |= V4L2_CTRL_FLAG_READ_ONLY;
+
+	pixel_rate = (link_freq_menu_items[0] * 2 * OV02A10_LANES) /
+		     OV02A10_BITS_PER_SAMPLE;
+	v4l2_ctrl_new_std(handler, NULL, V4L2_CID_PIXEL_RATE,
+			  0, pixel_rate, 1, pixel_rate);
+
+	h_blank = mode->hts_def - mode->width;
+	ov02a10->hblank = v4l2_ctrl_new_std(handler, NULL, V4L2_CID_HBLANK,
+					    h_blank, h_blank, 1, h_blank);
+	if (ov02a10->hblank)
+		ov02a10->hblank->flags |= V4L2_CTRL_FLAG_READ_ONLY;
+
+	ov02a10->vblank = v4l2_ctrl_new_std(handler, &ov02a10_ctrl_ops,
+					    V4L2_CID_VBLANK, mode->vts_def -
+					    mode->height,
+					    OV02A10_VTS_MAX - mode->height, 1,
+					    mode->vts_def - mode->height);
+
+	exposure_max = mode->vts_def - 4;
+	ov02a10->exposure = v4l2_ctrl_new_std(handler, &ov02a10_ctrl_ops,
+					      V4L2_CID_EXPOSURE,
+					      OV02A10_EXPOSURE_MIN,
+					      exposure_max,
+					      OV02A10_EXPOSURE_STEP,
+					      mode->exp_def);
+
+	ov02a10->anal_gain = v4l2_ctrl_new_std(handler, &ov02a10_ctrl_ops,
+					       V4L2_CID_ANALOGUE_GAIN,
+					       OV02A10_GAIN_MIN,
+					       OV02A10_GAIN_MAX,
+					       OV02A10_GAIN_STEP,
+					       OV02A10_GAIN_DEFAULT);
+
+	ov02a10->test_pattern =
+	   v4l2_ctrl_new_std_menu_items(handler,
+					&ov02a10_ctrl_ops,
+					V4L2_CID_TEST_PATTERN,
+					ARRAY_SIZE(ov02a10_test_pattern_menu) -
+					1, 0, 0, ov02a10_test_pattern_menu);
+
+	if (handler->error) {
+		ret = handler->error;
+		dev_err(&client->dev,
+			"Failed to init controls(%d)\n", ret);
+		goto err_free_handler;
+	}
+
+	ov02a10->subdev.ctrl_handler = handler;
+
+	return 0;
+
+err_free_handler:
+	v4l2_ctrl_handler_free(handler);
+
+	return ret;
+}
+
+static int ov02a10_check_sensor_id(struct ov02a10 *ov02a10)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
+	u16 id;
+	u8 pid = 0;
+	u8 ver = 0;
+	int ret;
+
+	/* Check sensor revision */
+	ret = ov02a10_read_reg(ov02a10, OV02A10_REG_CHIP_ID_H, &pid);
+	if (ret)
+		return ret;
+
+	ret = ov02a10_read_reg(ov02a10, OV02A10_REG_CHIP_ID_L, &ver);
+	if (ret)
+		return ret;
+
+	id = OV02A10_ID(pid, ver);
+	if (id != CHIP_ID) {
+		dev_err(&client->dev, "Unexpected sensor id(%04x)\n", id);
+		return ret;
+	}
+	dev_dbg(&client->dev, "Detected OV%04X sensor\n", id);
+
+	return 0;
+}
+
+static int ov02a10_configure_regulators(struct ov02a10 *ov02a10)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
+	unsigned int i;
+
+	for (i = 0; i < OV02A10_NUM_SUPPLIES; i++)
+		ov02a10->supplies[i].supply = ov02a10_supply_names[i];
+
+	return devm_regulator_bulk_get(&client->dev,
+				       OV02A10_NUM_SUPPLIES,
+				       ov02a10->supplies);
+}
+
+static int ov02a10_probe(struct i2c_client *client)
+{
+	struct device *dev = &client->dev;
+	struct ov02a10 *ov02a10;
+	u32 rotation;
+	u32 xclk_freq;
+	int ret;
+
+	dev_dbg(dev, "ov02a10 probe\n");
+	ov02a10 = devm_kzalloc(dev, sizeof(*ov02a10), GFP_KERNEL);
+	if (!ov02a10)
+		return -ENOMEM;
+
+	v4l2_i2c_subdev_init(&ov02a10->subdev, client, &ov02a10_subdev_ops);
+	ov02a10->fmt.code = MEDIA_BUS_FMT_SBGGR10_1X10;
+
+	/* optional indication of physical rotation of sensor */
+	ret = fwnode_property_read_u32(dev_fwnode(dev), "rotation",
+				       &rotation);
+	if (!ret) {
+		switch (rotation) {
+		case 180:
+			ov02a10->upside_down = true;
+			ov02a10->fmt.code = MEDIA_BUS_FMT_SRGGB10_1X10;
+			break;
+		case 0:
+			break;
+		default:
+			dev_warn(dev, "%u degrees rotation is not supported, ignoring...\n",
+				 rotation);
+		}
+	}
+
+	/* get system clock (xvclk) */
+	ov02a10->xvclk = devm_clk_get(dev, "xvclk");
+	if (IS_ERR(ov02a10->xvclk)) {
+		dev_err(dev, "Failed to get xvclk\n");
+		return -EINVAL;
+	}
+
+	ret = of_property_read_u32(dev->of_node, "clock-frequency", &xclk_freq);
+	if (ret) {
+		dev_err(dev, "Failed to get xclk frequency\n");
+		return ret;
+	}
+
+	/* external clock must be 24MHz, allow 1% tolerance */
+	if (xclk_freq < 23760000 || xclk_freq > 24240000) {
+		dev_err(dev, "external clock frequency %u is not supported\n",
+			xclk_freq);
+		return -EINVAL;
+	}
+	dev_dbg(dev, "external clock frequency %u\n", xclk_freq);
+
+	ret = clk_set_rate(ov02a10->xvclk, xclk_freq);
+	if (ret) {
+		dev_err(dev, "Failed to set xvclk frequency (24MHz)\n");
+		return ret;
+	}
+
+	ov02a10->pwdn_gpio = devm_gpiod_get(dev, "pwdn", GPIOD_OUT_LOW);
+	if (IS_ERR(ov02a10->pwdn_gpio)) {
+		dev_err(dev, "Failed to get powerdown-gpios\n");
+		return -EINVAL;
+	}
+
+	ov02a10->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
+	if (IS_ERR(ov02a10->reset_gpio)) {
+		dev_err(dev, "Failed to get reset-gpios\n");
+		return -EINVAL;
+	}
+
+	ret = ov02a10_configure_regulators(ov02a10);
+	if (ret) {
+		dev_err(dev, "Failed to get power regulators\n");
+		return ret;
+	}
+
+	mutex_init(&ov02a10->mutex);
+	ov02a10->cur_mode = &supported_modes[0];
+	ret = ov02a10_initialize_controls(ov02a10);
+	if (ret) {
+		dev_err(dev, "Failed to initialize controls\n");
+		goto err_destroy_mutex;
+	}
+
+	ret = __ov02a10_power_on(ov02a10);
+	if (ret)
+		goto err_free_handler;
+
+	ret = ov02a10_check_sensor_id(ov02a10);
+	if (ret)
+		goto err_power_off;
+
+	ov02a10->subdev.internal_ops = &ov02a10_internal_ops;
+	ov02a10->subdev.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+	ov02a10->subdev.entity.ops = &ov02a10_subdev_entity_ops;
+	ov02a10->subdev.entity.function = MEDIA_ENT_F_CAM_SENSOR;
+	ov02a10->pad.flags = MEDIA_PAD_FL_SOURCE;
+	ret = media_entity_pads_init(&ov02a10->subdev.entity, 1, &ov02a10->pad);
+	if (ret < 0) {
+		dev_err(dev, "failed to init entity pads: %d", ret);
+		goto err_power_off;
+	}
+
+	ret = v4l2_async_register_subdev(&ov02a10->subdev);
+	if (ret) {
+		dev_err(dev, "failed to register V4L2 subdev: %d",
+			ret);
+		goto err_clean_entity;
+	}
+
+	pm_runtime_set_active(dev);
+	pm_runtime_enable(dev);
+	pm_runtime_idle(dev);
+
+	return 0;
+
+err_clean_entity:
+	media_entity_cleanup(&ov02a10->subdev.entity);
+err_power_off:
+	__ov02a10_power_off(ov02a10);
+err_free_handler:
+	v4l2_ctrl_handler_free(ov02a10->subdev.ctrl_handler);
+err_destroy_mutex:
+	mutex_destroy(&ov02a10->mutex);
+
+	return ret;
+}
+
+static int ov02a10_remove(struct i2c_client *client)
+{
+	struct v4l2_subdev *sd = i2c_get_clientdata(client);
+	struct ov02a10 *ov02a10 = to_ov02a10(sd);
+
+	v4l2_async_unregister_subdev(sd);
+	media_entity_cleanup(&sd->entity);
+	v4l2_ctrl_handler_free(sd->ctrl_handler);
+	pm_runtime_disable(&client->dev);
+	if (!pm_runtime_status_suspended(&client->dev))
+		__ov02a10_power_off(ov02a10);
+	pm_runtime_set_suspended(&client->dev);
+	mutex_destroy(&ov02a10->mutex);
+
+	return 0;
+}
+
+#if IS_ENABLED(CONFIG_OF)
+static const struct of_device_id ov02a10_of_match[] = {
+	{ .compatible = "ovti,ov02a10" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, ov02a10_of_match);
+#endif
+
+static struct i2c_driver ov02a10_i2c_driver = {
+	.driver = {
+		.name = "ov02a10",
+		.pm = &ov02a10_pm_ops,
+		.of_match_table = ov02a10_of_match,
+	},
+	.probe_new	= &ov02a10_probe,
+	.remove		= &ov02a10_remove,
+};
+
+module_i2c_driver(ov02a10_i2c_driver);
+
+MODULE_AUTHOR("Dongchun Zhu <dongchun.zhu@mediatek.com>");
+MODULE_DESCRIPTION("OmniVision OV02A10 sensor driver");
+MODULE_LICENSE("GPL v2");
+
-- 
2.9.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply related	[flat|nested] 11+ messages in thread

* Re: [RFC,V2,2/2] media: i2c: Add Omnivision OV02A10 camera sensor driver
  2019-07-04  8:46 ` [RFC,V2,2/2] media: i2c: Add Omnivision OV02A10 camera sensor driver dongchun.zhu
@ 2019-07-08  7:52   ` Bingbu Cao
       [not found]     ` <8639e67ad6db40b78e48b00c875187dc@mtkmbs02n1.mediatek.inc>
  0 siblings, 1 reply; 11+ messages in thread
From: Bingbu Cao @ 2019-07-08  7:52 UTC (permalink / raw)
  To: dongchun.zhu, mchehab, robh+dt, mark.rutland, sakari.ailus,
	--to=drinkcat, tfiga, matthias.bgg, bingbu.cao
  Cc: devicetree, srv_heupstream, shengnan.wang, sj.huang,
	linux-mediatek, louis.kuo, linux-arm-kernel, linux-media



On 7/4/19 4:46 PM, dongchun.zhu@mediatek.com wrote:
> From: Dongchun Zhu <dongchun.zhu@mediatek.com>
> 
> This patch adds a V4L2 sub-device driver for OV02A10 image sensor.
> The OV02A10 is a 1/5" CMOS sensor from Omnivision.
> Supports output format: 10-bit Raw.
> The OV02A10 has a single MIPI lane interface and use the I2C bus for control and the CSI-2 bus for data.
> 
> Signed-off-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
> 
snip
> +
> +/* MIPI color bar enable output */
> +static const struct regval ov02a10_test_pattern_enable_regs[] = {
> +	{0xfd, 0x01},
> +	{0x0d, 0x00},
> +	{0xb6, 0x01},
> +	{0x01, 0x01},
> +	{0xfd, 0x01},
> +	{0xac, 0x01},
> +	{REG_NULL, 0x00}
Actually, you can use ARRAY_SIZE to write the regs, the REG_NULL can be
removed. However, it is not a problem.
...
snip...
> +static int ov02a10_set_fmt(struct v4l2_subdev *sd,
> +			   struct v4l2_subdev_pad_config *cfg,
> +			   struct v4l2_subdev_format *fmt)
> +{
> +	struct ov02a10 *ov02a10 = to_ov02a10(sd);
> +	struct v4l2_mbus_framefmt *mbus_fmt = &fmt->format;
> +	int ret = 0;
> +
> +	mutex_lock(&ov02a10->mutex);
> +
> +	if (ov02a10->streaming) {
> +		ret = -EBUSY;
> +		goto unlock;
I like return -EBUSY directly after mutex_unlock here and return 0 below.
> +	}
> +
> +	/* only one mode supported */
> +	mbus_fmt->code = ov02a10->fmt.code;
> +	ov02a10_fill_fmt(ov02a10->cur_mode, mbus_fmt);
> +	ov02a10->fmt = fmt->format;
> +
> +unlock:
> +	mutex_unlock(&ov02a10->mutex);
> +
> +	return ret;
> +}
> +
> +static int ov02a10_get_fmt(struct v4l2_subdev *sd,
> +			   struct v4l2_subdev_pad_config *cfg,
> +			   struct v4l2_subdev_format *fmt)
> +{
> +	struct ov02a10 *ov02a10 = to_ov02a10(sd);
> +	struct v4l2_mbus_framefmt *mbus_fmt = &fmt->format;
> +
> +	mutex_lock(&ov02a10->mutex);
> +
> +	fmt->format = ov02a10->fmt;
> +	mbus_fmt->code = ov02a10->fmt.code;
> +	ov02a10_fill_fmt(ov02a10->cur_mode, mbus_fmt);
> +
> +	mutex_unlock(&ov02a10->mutex);
> +
> +	return 0;
> +}
> +
> +static int ov02a10_enum_mbus_code(struct v4l2_subdev *sd,
> +				  struct v4l2_subdev_pad_config *cfg,
> +				  struct v4l2_subdev_mbus_code_enum *code)
> +{
> +	struct ov02a10 *ov02a10 = to_ov02a10(sd);
> +
> +	if (code->index >= ARRAY_SIZE(supported_modes) || !(code->index))
> +		return -EINVAL;
> +
> +	code->code = ov02a10->fmt.code;
> +
> +	return 0;
> +}
> +
> +static int ov02a10_enum_frame_sizes(struct v4l2_subdev *sd,
> +				    struct v4l2_subdev_pad_config *cfg,
> +				    struct v4l2_subdev_frame_size_enum *fse)
> +{
> +	if (fse->index >= ARRAY_SIZE(supported_modes) || !(fse->index))
> +		return -EINVAL;
> +
> +	fse->min_width  = supported_modes[fse->index].width;
> +	fse->max_width  = supported_modes[fse->index].width;
> +	fse->max_height = supported_modes[fse->index].height;
> +	fse->min_height = supported_modes[fse->index].height;
> +
> +	return 0;
> +}
> +
> +static int __ov02a10_power_on(struct ov02a10 *ov02a10)
> +{
> +	struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> +	struct device *dev = &client->dev;
> +	int ret;
> +
> +	ret = clk_prepare_enable(ov02a10->xvclk);
> +	if (ret < 0) {
> +		dev_err(dev, "Failed to enable xvclk\n");
> +		return ret;
> +	}
> +
> +	/* note: set 0 is high, set 1 is low */
> +	gpiod_set_value_cansleep(ov02a10->reset_gpio, 1);
> +	gpiod_set_value_cansleep(ov02a10->pwdn_gpio, 0);
> +
> +	ret = regulator_bulk_enable(OV02A10_NUM_SUPPLIES, ov02a10->supplies);
> +	if (ret < 0) {
> +		dev_err(dev, "Failed to enable regulators\n");
> +		goto disable_clk;
> +	}
> +	msleep_range(7);
> +
> +	gpiod_set_value_cansleep(ov02a10->pwdn_gpio, 1);
> +	msleep_range(10);
> +
> +	gpiod_set_value_cansleep(ov02a10->reset_gpio, 0);
> +	msleep_range(10);
> +
> +	return 0;
> +
> +disable_clk:
> +	clk_disable_unprepare(ov02a10->xvclk);
> +
> +	return ret;
> +}
> +
> +static void __ov02a10_power_off(struct ov02a10 *ov02a10)
> +{
> +	clk_disable_unprepare(ov02a10->xvclk);
> +	gpiod_set_value_cansleep(ov02a10->reset_gpio, 1);
> +	gpiod_set_value_cansleep(ov02a10->pwdn_gpio, 1);
> +	regulator_bulk_disable(OV02A10_NUM_SUPPLIES, ov02a10->supplies);
> +}
> +
> +static int __ov02a10_start_stream(struct ov02a10 *ov02a10)
> +{
> +	struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> +	int ret;
> +
> +	/* Apply default values of current mode */
> +	ret = ov02a10_write_array(ov02a10, ov02a10->cur_mode->reg_list);
> +	if (ret)
> +		return ret;
> +
> +	/* Apply customized values from user */
> +	ret = __v4l2_ctrl_handler_setup(ov02a10->subdev.ctrl_handler);
> +	if (ret)
> +		return ret;
> +
> +	/* Set Orientation be 180 degree */
Set orientation to 180 degree
> +	if (ov02a10->upside_down) {
> +		ret = ov02a10_write_reg(ov02a10, REG_MIRROR_FLIP_CONTROL,
> +					REG_CONFIG_MIRROR_FLIP);
> +		if (ret) {
> +			dev_err(&client->dev, "%s failed to set orientation\n",
> +				__func__);
> +			return ret;
> +		}
> +		ret = ov02a10_write_reg(ov02a10, REG_GLOBAL_EFFECTIVE,
> +					REG_ENABLE);
> +		if (ret < 0)
> +			return ret;
> +	}
> +
> +	/* set stream on register */
> +	return ov02a10_write_reg(ov02a10,
> +				 REG_SC_CTRL_MODE, SC_CTRL_MODE_STREAMING);
> +}
> +
> +static int __ov02a10_stop_stream(struct ov02a10 *ov02a10)
> +{
> +	return ov02a10_write_reg(ov02a10,
> +				 REG_SC_CTRL_MODE, SC_CTRL_MODE_STANDBY);
> +}
> +
> +static int ov02a10_entity_init_cfg(struct v4l2_subdev *subdev,
> +				   struct v4l2_subdev_pad_config *cfg)
> +{
> +	struct v4l2_subdev_format fmt = { 0 };
> +
> +	fmt.which = cfg ? V4L2_SUBDEV_FORMAT_TRY : V4L2_SUBDEV_FORMAT_ACTIVE;
> +	fmt.format.width = 1600;
> +	fmt.format.height = 1200;
> +
> +	ov02a10_set_fmt(subdev, cfg, &fmt);
> +
> +	return 0;
> +}
> +
> +static int ov02a10_s_stream(struct v4l2_subdev *sd, int on)
> +{
> +	struct ov02a10 *ov02a10 = to_ov02a10(sd);
> +	struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> +	int ret = 0;
> +
> +	dev_dbg(&client->dev, "ov02a10 s_stream (%d)\n", on);
> +	mutex_lock(&ov02a10->mutex);
> +
> +	if (ov02a10->streaming == on)
> +		goto unlock_and_return;
> +
> +	if (on) {
> +		ret = pm_runtime_get_sync(&client->dev);
> +		if (ret < 0) {
> +			pm_runtime_put_noidle(&client->dev);
> +			goto unlock_and_return;
> +		}
> +
> +		ret = __ov02a10_start_stream(ov02a10);
> +		if (ret) {
> +			__ov02a10_stop_stream(ov02a10);
> +			ov02a10->streaming = !on;
> +			goto err_rpm_put;
> +		}
> +	} else {
> +		__ov02a10_stop_stream(ov02a10);
> +		pm_runtime_put(&client->dev);
> +	}
> +
> +	ov02a10->streaming = on;
> +	mutex_unlock(&ov02a10->mutex);
> +
> +	return ret;
> +
> +err_rpm_put:
> +	pm_runtime_put(&client->dev);
> +unlock_and_return:
> +	mutex_unlock(&ov02a10->mutex);
> +
> +	return ret;
> +}
> +
> +static int ov02a10_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh)
> +{
> +	struct ov02a10 *ov02a10 = to_ov02a10(sd);
> +	struct v4l2_mbus_framefmt *try_fmt = v4l2_subdev_get_try_format(sd,
> +									fh->pad,
> +									0);
> +
> +	mutex_lock(&ov02a10->mutex);
> +	/* Initialize try_fmt */
> +	try_fmt->code = ov02a10->fmt.code;
> +	ov02a10_fill_fmt(&supported_modes[0], try_fmt);
> +
> +	mutex_unlock(&ov02a10->mutex);
> +
> +	return 0;
> +}
> +
> +static int __maybe_unused ov02a10_runtime_resume(struct device *dev)
> +{
> +	struct i2c_client *client = to_i2c_client(dev);
> +	struct v4l2_subdev *sd = i2c_get_clientdata(client);
> +	struct ov02a10 *ov02a10 = to_ov02a10(sd);
> +
> +	return __ov02a10_power_on(ov02a10);
> +}
> +
> +static int __maybe_unused ov02a10_runtime_suspend(struct device *dev)
> +{
> +	struct i2c_client *client = to_i2c_client(dev);
> +	struct v4l2_subdev *sd = i2c_get_clientdata(client);
> +	struct ov02a10 *ov02a10 = to_ov02a10(sd);
> +
> +	__ov02a10_power_off(ov02a10);
> +
> +	return 0;
> +}
> +
> +static const struct dev_pm_ops ov02a10_pm_ops = {
> +	SET_RUNTIME_PM_OPS(ov02a10_runtime_suspend,
> +			   ov02a10_runtime_resume, NULL)
> +};
> +
> +static int ov02a10_set_test_pattern(struct ov02a10 *ov02a10, s32 value)
> +{
> +	if (value)
> +		return ov02a10_write_array(ov02a10,
> +					   ov02a10_test_pattern_enable_regs);
> +
> +	return ov02a10_write_array(ov02a10,
> +		ov02a10_test_pattern_disable_regs);
> +}
> +
> +static int ov02a10_set_ctrl(struct v4l2_ctrl *ctrl)
> +{
> +	struct ov02a10 *ov02a10 = container_of(ctrl->handler,
> +					     struct ov02a10, ctrl_handler);
> +	struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> +	s64 max_expo;
> +	int ret;
> +
> +	/* Propagate change of current control to all related controls */
> +	if (ctrl->id == V4L2_CID_VBLANK) {
> +		/* Update max exposure while meeting expected vblanking */
> +		max_expo = ov02a10->cur_mode->height + ctrl->val - 4;
> +		__v4l2_ctrl_modify_range(ov02a10->exposure,
> +					 ov02a10->exposure->minimum, max_expo,
> +					 ov02a10->exposure->step,
> +					 ov02a10->exposure->default_value);
> +	}
> +
> +	/* V4L2 controls values will be applied only when power is already up */
> +	if (!pm_runtime_get_if_in_use(&client->dev))
> +		return 0;
> +
> +	switch (ctrl->id) {
> +	case V4L2_CID_EXPOSURE:
> +		ret = ov02a10_write_reg(ov02a10, REG_PAGE_SWITCH, REG_ENABLE);
> +		if (ret < 0)
> +			return ret;
> +		ret = ov02a10_write_reg(ov02a10, OV02A10_REG_EXPOSURE_H,
> +					((ctrl->val >> 8) & 0xFF));
> +		if (!ret) {
> +			ret = ov02a10_write_reg(ov02a10, OV02A10_REG_EXPOSURE_L,
> +						(ctrl->val & 0xFF));
> +			if (ret < 0)
> +				return ret;
> +		}
> +		ret = ov02a10_write_reg(ov02a10, REG_GLOBAL_EFFECTIVE,
> +					REG_ENABLE);
> +		if (ret < 0)
> +			return ret;
> +		break;
> +	case V4L2_CID_ANALOGUE_GAIN:
> +		ret = ov02a10_write_reg(ov02a10, REG_PAGE_SWITCH, REG_ENABLE);
> +		if (ret < 0)
> +			return ret;
> +		ret = ov02a10_write_reg(ov02a10, OV02A10_REG_GAIN,
> +					(ctrl->val & 0xFF));
> +		if (ret < 0)
> +			return ret;
> +		ret = ov02a10_write_reg(ov02a10, REG_GLOBAL_EFFECTIVE,
> +					REG_ENABLE);
> +		if (ret < 0)
> +			return ret;
> +		break;
> +	case V4L2_CID_VBLANK:
> +		ret = ov02a10_write_reg(ov02a10, REG_PAGE_SWITCH, REG_ENABLE);
> +		if (ret < 0)
> +			return ret;
> +		ret = ov02a10_write_reg(ov02a10, OV02A10_REG_VTS_H,
> +					(((ctrl->val +
> +					ov02a10->cur_mode->height - 1224) >> 8)
> +					& 0xFF));
1224 is hard-coded here, could you add some comments? Is it a sensor
setting sensitive value?
> +		if (!ret) {
> +			ret = ov02a10_write_reg(ov02a10, OV02A10_REG_VTS_L,
> +						((ctrl->val +
> +						ov02a10->cur_mode->height -
> +						1224) & 0xFF));
ditto.
> +			if (ret < 0)
> +				return ret;
> +		}
> +		ret = ov02a10_write_reg(ov02a10, REG_GLOBAL_EFFECTIVE,
> +					REG_ENABLE);
> +		if (ret < 0)
> +			return ret;
> +		break;
> +	case V4L2_CID_TEST_PATTERN:
> +		ret = ov02a10_set_test_pattern(ov02a10, ctrl->val);
> +		if (ret < 0)
> +			return ret;
> +		break;
> +	default:
> +		dev_warn(&client->dev, "%s Unhandled id:0x%x, val:0x%x\n",
> +			 __func__, ctrl->id, ctrl->val);
> +		ret = -EINVAL;
> +		break;
> +	};
> +
> +	pm_runtime_put(&client->dev);
> +
> +	return ret;
> +}
> +
> +static const struct v4l2_subdev_video_ops ov02a10_video_ops = {
> +	.s_stream = ov02a10_s_stream,
> +};
> +
> +static const struct v4l2_subdev_pad_ops ov02a10_pad_ops = {
> +	.init_cfg = ov02a10_entity_init_cfg,
> +	.enum_mbus_code = ov02a10_enum_mbus_code,
> +	.enum_frame_size = ov02a10_enum_frame_sizes,
> +	.get_fmt = ov02a10_get_fmt,
> +	.set_fmt = ov02a10_set_fmt,
> +};
> +
> +static const struct v4l2_subdev_ops ov02a10_subdev_ops = {
> +	.video	= &ov02a10_video_ops,
> +	.pad	= &ov02a10_pad_ops,
> +};
> +
> +static const struct media_entity_operations ov02a10_subdev_entity_ops = {
> +	.link_validate = v4l2_subdev_link_validate,
> +};
> +
> +static const struct v4l2_subdev_internal_ops ov02a10_internal_ops = {
> +	.open = ov02a10_open,
> +};
> +
> +static const struct v4l2_ctrl_ops ov02a10_ctrl_ops = {
> +	.s_ctrl = ov02a10_set_ctrl,
> +};
> +
> +static int ov02a10_initialize_controls(struct ov02a10 *ov02a10)
> +{
> +	struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> +	const struct ov02a10_mode *mode;
> +	struct v4l2_ctrl_handler *handler;
> +	struct v4l2_ctrl *ctrl;
> +	u64 exposure_max;
> +	u32 pixel_rate, h_blank;
> +	int ret;
> +
> +	handler = &ov02a10->ctrl_handler;
> +	mode = ov02a10->cur_mode;
> +	ret = v4l2_ctrl_handler_init(handler, 10);
> +	if (ret)
> +		return ret;
> +	handler->lock = &ov02a10->mutex;
> +
> +	ctrl = v4l2_ctrl_new_int_menu(handler, NULL, V4L2_CID_LINK_FREQ,
> +				      0, 0, link_freq_menu_items);
> +	if (ctrl)
> +		ctrl->flags |= V4L2_CTRL_FLAG_READ_ONLY;
> +
> +	pixel_rate = (link_freq_menu_items[0] * 2 * OV02A10_LANES) /
> +		     OV02A10_BITS_PER_SAMPLE;
> +	v4l2_ctrl_new_std(handler, NULL, V4L2_CID_PIXEL_RATE,
> +			  0, pixel_rate, 1, pixel_rate);
> +
> +	h_blank = mode->hts_def - mode->width;
> +	ov02a10->hblank = v4l2_ctrl_new_std(handler, NULL, V4L2_CID_HBLANK,
> +					    h_blank, h_blank, 1, h_blank);
> +	if (ov02a10->hblank)
> +		ov02a10->hblank->flags |= V4L2_CTRL_FLAG_READ_ONLY;
> +
> +	ov02a10->vblank = v4l2_ctrl_new_std(handler, &ov02a10_ctrl_ops,
> +					    V4L2_CID_VBLANK, mode->vts_def -
> +					    mode->height,
> +					    OV02A10_VTS_MAX - mode->height, 1,
> +					    mode->vts_def - mode->height);
> +
> +	exposure_max = mode->vts_def - 4;
> +	ov02a10->exposure = v4l2_ctrl_new_std(handler, &ov02a10_ctrl_ops,
> +					      V4L2_CID_EXPOSURE,
> +					      OV02A10_EXPOSURE_MIN,
> +					      exposure_max,
> +					      OV02A10_EXPOSURE_STEP,
> +					      mode->exp_def);
> +
> +	ov02a10->anal_gain = v4l2_ctrl_new_std(handler, &ov02a10_ctrl_ops,
> +					       V4L2_CID_ANALOGUE_GAIN,
> +					       OV02A10_GAIN_MIN,
> +					       OV02A10_GAIN_MAX,
> +					       OV02A10_GAIN_STEP,
> +					       OV02A10_GAIN_DEFAULT);
> +
> +	ov02a10->test_pattern =
> +	   v4l2_ctrl_new_std_menu_items(handler,
> +					&ov02a10_ctrl_ops,
> +					V4L2_CID_TEST_PATTERN,
> +					ARRAY_SIZE(ov02a10_test_pattern_menu) -
> +					1, 0, 0, ov02a10_test_pattern_menu);
> +
> +	if (handler->error) {
> +		ret = handler->error;
> +		dev_err(&client->dev,
> +			"Failed to init controls(%d)\n", ret);
> +		goto err_free_handler;
> +	}
> +
> +	ov02a10->subdev.ctrl_handler = handler;
> +
> +	return 0;
> +
> +err_free_handler:
> +	v4l2_ctrl_handler_free(handler);
> +
> +	return ret;
> +}
> +
> +static int ov02a10_check_sensor_id(struct ov02a10 *ov02a10)
> +{
> +	struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> +	u16 id;
> +	u8 pid = 0;
> +	u8 ver = 0;
> +	int ret;
> +
> +	/* Check sensor revision */
> +	ret = ov02a10_read_reg(ov02a10, OV02A10_REG_CHIP_ID_H, &pid);
> +	if (ret)
> +		return ret;
> +
> +	ret = ov02a10_read_reg(ov02a10, OV02A10_REG_CHIP_ID_L, &ver);
> +	if (ret)
> +		return ret;
> +
> +	id = OV02A10_ID(pid, ver);
> +	if (id != CHIP_ID) {
> +		dev_err(&client->dev, "Unexpected sensor id(%04x)\n", id);
> +		return ret;
> +	}
> +	dev_dbg(&client->dev, "Detected OV%04X sensor\n", id);
> +
> +	return 0;
> +}
> +
> +static int ov02a10_configure_regulators(struct ov02a10 *ov02a10)
> +{
> +	struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> +	unsigned int i;
> +
> +	for (i = 0; i < OV02A10_NUM_SUPPLIES; i++)
> +		ov02a10->supplies[i].supply = ov02a10_supply_names[i];
> +
> +	return devm_regulator_bulk_get(&client->dev,
> +				       OV02A10_NUM_SUPPLIES,
> +				       ov02a10->supplies);
> +}
> +
> +static int ov02a10_probe(struct i2c_client *client)
> +{
> +	struct device *dev = &client->dev;
> +	struct ov02a10 *ov02a10;
> +	u32 rotation;
> +	u32 xclk_freq;
> +	int ret;
> +
> +	dev_dbg(dev, "ov02a10 probe\n");
I think this line is not needed at all.
> +	ov02a10 = devm_kzalloc(dev, sizeof(*ov02a10), GFP_KERNEL);
> +	if (!ov02a10)
> +		return -ENOMEM;
> +
> +	v4l2_i2c_subdev_init(&ov02a10->subdev, client, &ov02a10_subdev_ops);
> +	ov02a10->fmt.code = MEDIA_BUS_FMT_SBGGR10_1X10;
> +
> +	/* optional indication of physical rotation of sensor */
> +	ret = fwnode_property_read_u32(dev_fwnode(dev), "rotation",
> +				       &rotation);
> +	if (!ret) {
> +		switch (rotation) {
> +		case 180:
> +			ov02a10->upside_down = true;
> +			ov02a10->fmt.code = MEDIA_BUS_FMT_SRGGB10_1X10;
> +			break;
> +		case 0:
> +			break;
> +		default:
> +			dev_warn(dev, "%u degrees rotation is not supported, ignoring...\n",
> +				 rotation);
> +		}
> +	}
> +
> +	/* get system clock (xvclk) */
> +	ov02a10->xvclk = devm_clk_get(dev, "xvclk");
> +	if (IS_ERR(ov02a10->xvclk)) {
> +		dev_err(dev, "Failed to get xvclk\n");
> +		return -EINVAL;
> +	}
> +
> +	ret = of_property_read_u32(dev->of_node, "clock-frequency", &xclk_freq);
> +	if (ret) {
> +		dev_err(dev, "Failed to get xclk frequency\n");
> +		return ret;
> +	}
> +
> +	/* external clock must be 24MHz, allow 1% tolerance */
> +	if (xclk_freq < 23760000 || xclk_freq > 24240000) {
> +		dev_err(dev, "external clock frequency %u is not supported\n",
> +			xclk_freq);
> +		return -EINVAL;
> +	}
> +	dev_dbg(dev, "external clock frequency %u\n", xclk_freq);
> +
> +	ret = clk_set_rate(ov02a10->xvclk, xclk_freq);
> +	if (ret) {
> +		dev_err(dev, "Failed to set xvclk frequency (24MHz)\n");
> +		return ret;
> +	}
> +
> +	ov02a10->pwdn_gpio = devm_gpiod_get(dev, "pwdn", GPIOD_OUT_LOW);
> +	if (IS_ERR(ov02a10->pwdn_gpio)) {
> +		dev_err(dev, "Failed to get powerdown-gpios\n");
> +		return -EINVAL;
> +	}
> +
> +	ov02a10->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
> +	if (IS_ERR(ov02a10->reset_gpio)) {
> +		dev_err(dev, "Failed to get reset-gpios\n");
> +		return -EINVAL;
> +	}
> +
> +	ret = ov02a10_configure_regulators(ov02a10);
> +	if (ret) {
> +		dev_err(dev, "Failed to get power regulators\n");
> +		return ret;
> +	}
> +
> +	mutex_init(&ov02a10->mutex);
> +	ov02a10->cur_mode = &supported_modes[0];
> +	ret = ov02a10_initialize_controls(ov02a10);
> +	if (ret) {
> +		dev_err(dev, "Failed to initialize controls\n");
> +		goto err_destroy_mutex;
> +	}
> +
> +	ret = __ov02a10_power_on(ov02a10);
> +	if (ret)
> +		goto err_free_handler;
> +
> +	ret = ov02a10_check_sensor_id(ov02a10);
> +	if (ret)
> +		goto err_power_off;
> +
> +	ov02a10->subdev.internal_ops = &ov02a10_internal_ops;
> +	ov02a10->subdev.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
> +	ov02a10->subdev.entity.ops = &ov02a10_subdev_entity_ops;
> +	ov02a10->subdev.entity.function = MEDIA_ENT_F_CAM_SENSOR;
> +	ov02a10->pad.flags = MEDIA_PAD_FL_SOURCE;
> +	ret = media_entity_pads_init(&ov02a10->subdev.entity, 1, &ov02a10->pad);
> +	if (ret < 0) {
> +		dev_err(dev, "failed to init entity pads: %d", ret);
> +		goto err_power_off;
> +	}
> +
> +	ret = v4l2_async_register_subdev(&ov02a10->subdev);
> +	if (ret) {
> +		dev_err(dev, "failed to register V4L2 subdev: %d",
> +			ret);
> +		goto err_clean_entity;
> +	}
> +
> +	pm_runtime_set_active(dev);
> +	pm_runtime_enable(dev);
> +	pm_runtime_idle(dev);
> +
> +	return 0;
> +
> +err_clean_entity:
> +	media_entity_cleanup(&ov02a10->subdev.entity);
> +err_power_off:
> +	__ov02a10_power_off(ov02a10);
> +err_free_handler:
> +	v4l2_ctrl_handler_free(ov02a10->subdev.ctrl_handler);
> +err_destroy_mutex:
> +	mutex_destroy(&ov02a10->mutex);
> +
> +	return ret;
> +}
> +
> +static int ov02a10_remove(struct i2c_client *client)
> +{
> +	struct v4l2_subdev *sd = i2c_get_clientdata(client);
> +	struct ov02a10 *ov02a10 = to_ov02a10(sd);
> +
> +	v4l2_async_unregister_subdev(sd);
> +	media_entity_cleanup(&sd->entity);
> +	v4l2_ctrl_handler_free(sd->ctrl_handler);
> +	pm_runtime_disable(&client->dev);
> +	if (!pm_runtime_status_suspended(&client->dev))
> +		__ov02a10_power_off(ov02a10);
> +	pm_runtime_set_suspended(&client->dev);
> +	mutex_destroy(&ov02a10->mutex);
> +
> +	return 0;
> +}
> +
> +#if IS_ENABLED(CONFIG_OF)
> +static const struct of_device_id ov02a10_of_match[] = {
> +	{ .compatible = "ovti,ov02a10" },
> +	{},
> +};
> +MODULE_DEVICE_TABLE(of, ov02a10_of_match);
> +#endif
> +
> +static struct i2c_driver ov02a10_i2c_driver = {
> +	.driver = {
> +		.name = "ov02a10",
> +		.pm = &ov02a10_pm_ops,
> +		.of_match_table = ov02a10_of_match,
> +	},
> +	.probe_new	= &ov02a10_probe,
> +	.remove		= &ov02a10_remove,
> +};
> +
> +module_i2c_driver(ov02a10_i2c_driver);
> +
> +MODULE_AUTHOR("Dongchun Zhu <dongchun.zhu@mediatek.com>");
> +MODULE_DESCRIPTION("OmniVision OV02A10 sensor driver");
> +MODULE_LICENSE("GPL v2");
> +
> 
Other part looks good to me.

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: [RFC,V2,1/2] media: dt-bindings: media: i2c: Add bindings for OV02A10
  2019-07-04  8:46 ` [RFC, V2, 1/2] media: dt-bindings: media: i2c: Add bindings for OV02A10 dongchun.zhu
@ 2019-07-22 23:49   ` Rob Herring
       [not found]     ` <5d5d644af9334609bb7c3ff745b2e754@mtkmbs02n1.mediatek.inc>
  2019-07-23  7:41   ` Sakari Ailus
  1 sibling, 1 reply; 11+ messages in thread
From: Rob Herring @ 2019-07-22 23:49 UTC (permalink / raw)
  To: dongchun.zhu
  Cc: mark.rutland, devicetree, srv_heupstream, shengnan.wang,
	--to=drinkcat, tfiga, louis.kuo, sj.huang, linux-mediatek,
	sakari.ailus, matthias.bgg, bingbu.cao, mchehab,
	linux-arm-kernel, linux-media

On Thu, Jul 04, 2019 at 04:46:50PM +0800, dongchun.zhu@mediatek.com wrote:
> From: Dongchun Zhu <dongchun.zhu@mediatek.com>
> 
> Add device tree binding documentation for the OV02A10 camera sensor.
> 
> Signed-off-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
> ---
>  .../devicetree/bindings/media/i2c/ov02a10.txt      | 43 ++++++++++++++++++++++
>  MAINTAINERS                                        |  7 ++++
>  2 files changed, 50 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/i2c/ov02a10.txt
> 
> diff --git a/Documentation/devicetree/bindings/media/i2c/ov02a10.txt b/Documentation/devicetree/bindings/media/i2c/ov02a10.txt
> new file mode 100644
> index 0000000..d40aa87
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/i2c/ov02a10.txt
> @@ -0,0 +1,43 @@
> +* Omnivision OV02A10 MIPI CSI-2 sensor
> +
> +Required Properties:
> +- compatible: shall be "ovti,ov02a10"
> +- clocks: reference to the xvclk input clock
> +- clock-names: shall be "xvclk"
> +- avdd-supply: Analog voltage supply, 2.8 volts
> +- dovdd-supply: Digital I/O voltage supply, 1.8 volts
> +- dvdd-supply: Digital core voltage supply, 1.8 volts
> +- reset-gpios: Low active reset gpio
> +
> +The device node shall contain one 'port' child node with an
> +'endpoint' subnode for its digital output video port,
> +in accordance with the video interface bindings defined in
> +Documentation/devicetree/bindings/media/video-interfaces.txt.
> +The endpoint optional property 'data-lanes' shall be "<1>".
> +
> +Example:
> +&i2c4 {
> +	ov02a10: camera-sensor@3d {
> +		compatible = "ovti,ov02a10";
> +		reg = <0x3d>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&camera_pins_cam1_mclk_on>;
> +
> +		clocks = <&topckgen CLK_TOP_MUX_CAMTG2>,
> +			<&topckgen CLK_TOP_UNIVP_192M_D8>;
> +		clock-names = "xvclk", "freq_mux";
> +
> +		avdd-supply = <&mt6358_vcama1_reg>;
> +		dvdd-supply = <&mt6358_vcn18_reg>;
> +		dovdd-supply = <&mt6358_vcamio_reg>;
> +		pwdn-gpios = <&pio 107 1>;

Not documented. If you need this, use 'powerdown-gpios' instead.

> +		reset-gpios = <&pio 109 1>;
> +
> +		port {
> +		   ov02a10_core: endpoint {
> +		       remote-endpoint = <&ov02a10_0>;
> +			   data-lanes = <1>;
> +			};
> +		};
> +	};
> +};
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 5cfbea4..62b81ff 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -11571,6 +11571,13 @@ T:	git git://linuxtv.org/media_tree.git
>  S:	Maintained
>  F:	drivers/media/i2c/ov13858.c
>  
> +OMNIVISION OV02A10 SENSOR DRIVER
> +M:	Dongchun Zhu <dongchun.zhu@mediatek.com>
> +L:	linux-media@vger.kernel.org
> +T:	git git://linuxtv.org/media_tree.git
> +S:	Maintained
> +F:	Documentation/devicetree/bindings/media/i2c/ov02a10.txt
> +
>  OMNIVISION OV2680 SENSOR DRIVER
>  M:	Rui Miguel Silva <rmfrfs@gmail.com>
>  L:	linux-media@vger.kernel.org
> -- 
> 2.9.2
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: [RFC,V2,1/2] media: dt-bindings: media: i2c: Add bindings for OV02A10
  2019-07-04  8:46 ` [RFC, V2, 1/2] media: dt-bindings: media: i2c: Add bindings for OV02A10 dongchun.zhu
  2019-07-22 23:49   ` [RFC,V2,1/2] " Rob Herring
@ 2019-07-23  7:41   ` Sakari Ailus
       [not found]     ` <ef65288c523f405396991bd6d757bba0@mtkmbs02n1.mediatek.inc>
  1 sibling, 1 reply; 11+ messages in thread
From: Sakari Ailus @ 2019-07-23  7:41 UTC (permalink / raw)
  To: dongchun.zhu
  Cc: mark.rutland, devicetree, srv_heupstream, shengnan.wang,
	--to=drinkcat, tfiga, louis.kuo, sj.huang, robh+dt,
	linux-mediatek, matthias.bgg, bingbu.cao, mchehab,
	linux-arm-kernel, linux-media

Hi Dongchun,

On Thu, Jul 04, 2019 at 04:46:50PM +0800, dongchun.zhu@mediatek.com wrote:
> From: Dongchun Zhu <dongchun.zhu@mediatek.com>
> 
> Add device tree binding documentation for the OV02A10 camera sensor.
> 
> Signed-off-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
> ---
>  .../devicetree/bindings/media/i2c/ov02a10.txt      | 43 ++++++++++++++++++++++
>  MAINTAINERS                                        |  7 ++++
>  2 files changed, 50 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/i2c/ov02a10.txt
> 
> diff --git a/Documentation/devicetree/bindings/media/i2c/ov02a10.txt b/Documentation/devicetree/bindings/media/i2c/ov02a10.txt
> new file mode 100644
> index 0000000..d40aa87
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/i2c/ov02a10.txt
> @@ -0,0 +1,43 @@
> +* Omnivision OV02A10 MIPI CSI-2 sensor
> +
> +Required Properties:
> +- compatible: shall be "ovti,ov02a10"
> +- clocks: reference to the xvclk input clock
> +- clock-names: shall be "xvclk"
> +- avdd-supply: Analog voltage supply, 2.8 volts
> +- dovdd-supply: Digital I/O voltage supply, 1.8 volts
> +- dvdd-supply: Digital core voltage supply, 1.8 volts
> +- reset-gpios: Low active reset gpio
> +
> +The device node shall contain one 'port' child node with an
> +'endpoint' subnode for its digital output video port,
> +in accordance with the video interface bindings defined in
> +Documentation/devicetree/bindings/media/video-interfaces.txt.
> +The endpoint optional property 'data-lanes' shall be "<1>".

How many lanes does the module (or the sensor) have?

> +
> +Example:
> +&i2c4 {
> +	ov02a10: camera-sensor@3d {
> +		compatible = "ovti,ov02a10";
> +		reg = <0x3d>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&camera_pins_cam1_mclk_on>;
> +
> +		clocks = <&topckgen CLK_TOP_MUX_CAMTG2>,
> +			<&topckgen CLK_TOP_UNIVP_192M_D8>;
> +		clock-names = "xvclk", "freq_mux";
> +
> +		avdd-supply = <&mt6358_vcama1_reg>;
> +		dvdd-supply = <&mt6358_vcn18_reg>;
> +		dovdd-supply = <&mt6358_vcamio_reg>;
> +		pwdn-gpios = <&pio 107 1>;
> +		reset-gpios = <&pio 109 1>;
> +
> +		port {
> +		   ov02a10_core: endpoint {
> +		       remote-endpoint = <&ov02a10_0>;

Indentation is still wrong. :-(

> +			   data-lanes = <1>;
> +			};
> +		};
> +	};
> +};
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 5cfbea4..62b81ff 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -11571,6 +11571,13 @@ T:	git git://linuxtv.org/media_tree.git
>  S:	Maintained
>  F:	drivers/media/i2c/ov13858.c
>  
> +OMNIVISION OV02A10 SENSOR DRIVER
> +M:	Dongchun Zhu <dongchun.zhu@mediatek.com>
> +L:	linux-media@vger.kernel.org
> +T:	git git://linuxtv.org/media_tree.git
> +S:	Maintained
> +F:	Documentation/devicetree/bindings/media/i2c/ov02a10.txt
> +
>  OMNIVISION OV2680 SENSOR DRIVER
>  M:	Rui Miguel Silva <rmfrfs@gmail.com>
>  L:	linux-media@vger.kernel.org

-- 
Kind regards,

Sakari Ailus
sakari.ailus@linux.intel.com

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: [RFC,V2,1/2] media: dt-bindings: media: i2c: Add bindings for OV02A10
       [not found]     ` <ef65288c523f405396991bd6d757bba0@mtkmbs02n1.mediatek.inc>
@ 2019-08-17  3:53       ` Dongchun Zhu
  2019-08-17 21:32         ` Sakari Ailus
  0 siblings, 1 reply; 11+ messages in thread
From: Dongchun Zhu @ 2019-08-17  3:53 UTC (permalink / raw)
  To: sakari.ailus
  Cc: mark.rutland, devicetree, drinkcat, srv_heupstream, menghui.lin,
	tfiga, shengnan.wang, louis.kuo, sj.huang, robh+dt,
	linux-mediatek, matthias.bgg, bingbu.cao, mchehab,
	linux-arm-kernel, linux-media


Hi Sakari,

On Tue, 2019-07-23 at 10:41 +0300, Sakari Ailus wrote:
> 
> Hi Dongchun,
> 
> On Thu, Jul 04, 2019 at 04:46:50PM +0800, dongchun.zhu@mediatek.com wrote:
> > From: Dongchun Zhu <dongchun.zhu@mediatek.com>
> >
> > Add device tree binding documentation for the OV02A10 camera sensor.
> >
> > Signed-off-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
> > ---
> >  .../devicetree/bindings/media/i2c/ov02a10.txt      | 43 ++++++++++++++++++++++
> >  MAINTAINERS                                        |  7 ++++
> >  2 files changed, 50 insertions(+)
> >  create mode 100644
> > Documentation/devicetree/bindings/media/i2c/ov02a10.txt
> >
> > diff --git a/Documentation/devicetree/bindings/media/i2c/ov02a10.txt
> > b/Documentation/devicetree/bindings/media/i2c/ov02a10.txt
> > new file mode 100644
> > index 0000000..d40aa87
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/media/i2c/ov02a10.txt
> > @@ -0,0 +1,43 @@
> > +* Omnivision OV02A10 MIPI CSI-2 sensor
> > +
> > +Required Properties:
> > +- compatible: shall be "ovti,ov02a10"
> > +- clocks: reference to the xvclk input clock
> > +- clock-names: shall be "xvclk"
> > +- avdd-supply: Analog voltage supply, 2.8 volts
> > +- dovdd-supply: Digital I/O voltage supply, 1.8 volts
> > +- dvdd-supply: Digital core voltage supply, 1.8 volts
> > +- reset-gpios: Low active reset gpio
> > +
> > +The device node shall contain one 'port' child node with an
> > +'endpoint' subnode for its digital output video port, in accordance
> > +with the video interface bindings defined in
> > +Documentation/devicetree/bindings/media/video-interfaces.txt.
> > +The endpoint optional property 'data-lanes' shall be "<1>".
> 
> How many lanes does the module (or the sensor) have?
> 

From sensor datasheet, OV02A10 supports 1-lane MIPI interface.

> > +
> > +Example:
> > +&i2c4 {
> > +ov02a10: camera-sensor@3d {
> > +compatible = "ovti,ov02a10";
> > +reg = <0x3d>;
> > +pinctrl-names = "default";
> > +pinctrl-0 = <&camera_pins_cam1_mclk_on>;
> > +
> > +clocks = <&topckgen CLK_TOP_MUX_CAMTG2>,
> > +<&topckgen CLK_TOP_UNIVP_192M_D8>;
> > +clock-names = "xvclk", "freq_mux";
> > +
> > +avdd-supply = <&mt6358_vcama1_reg>;
> > +dvdd-supply = <&mt6358_vcn18_reg>;
> > +dovdd-supply = <&mt6358_vcamio_reg>;
> > +pwdn-gpios = <&pio 107 1>;
> > +reset-gpios = <&pio 109 1>;
> > +
> > +port {
> > +   ov02a10_core: endpoint {
> > +       remote-endpoint = <&ov02a10_0>;
> 
> Indentation is still wrong. :-(
> 

Fixed in next release.

> > +   data-lanes = <1>;
> > +};
> > +};
> > +};
> > +};
> > diff --git a/MAINTAINERS b/MAINTAINERS index 5cfbea4..62b81ff 100644
> > --- a/MAINTAINERS
> > +++ b/MAINTAINERS
> > @@ -11571,6 +11571,13 @@ T:git git://linuxtv.org/media_tree.git
> >  S:Maintained
> >  F:drivers/media/i2c/ov13858.c
> >
> > +OMNIVISION OV02A10 SENSOR DRIVER
> > +M:Dongchun Zhu <dongchun.zhu@mediatek.com>
> > +L:linux-media@vger.kernel.org
> > +T:git git://linuxtv.org/media_tree.git
> > +S:Maintained
> > +F:Documentation/devicetree/bindings/media/i2c/ov02a10.txt
> > +
> >  OMNIVISION OV2680 SENSOR DRIVER
> >  M:Rui Miguel Silva <rmfrfs@gmail.com>
> >  L:linux-media@vger.kernel.org
> 
> --
> Kind regards,
> 
> Sakari Ailus
> sakari.ailus@linux.intel.com
> 
> _______________________________________________
> Linux-mediatek mailing list
> Linux-mediatek@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-mediatek
> *********************MEDIATEK Confidential/Internal Use*********************



_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: [RFC,V2,1/2] media: dt-bindings: media: i2c: Add bindings for OV02A10
       [not found]     ` <5d5d644af9334609bb7c3ff745b2e754@mtkmbs02n1.mediatek.inc>
@ 2019-08-17  5:03       ` Dongchun Zhu
  0 siblings, 0 replies; 11+ messages in thread
From: Dongchun Zhu @ 2019-08-17  5:03 UTC (permalink / raw)
  To: Rob Herring
  Cc: mark.rutland, devicetree, drinkcat, srv_heupstream, menghui.lin,
	Sakari Ailus, tfiga, shengnan.wang, louis.kuo, sj.huang, robh+dt,
	linux-mediatek, matthias.bgg, bingbu.cao, mchehab,
	linux-arm-kernel, linux-media


Hi Rob,

On Mon, 2019-07-22 at 18:49 -0500, Rob Herring wrote:
> 
> On Thu, Jul 04, 2019 at 04:46:50PM +0800, dongchun.zhu@mediatek.com wrote:
> > From: Dongchun Zhu <dongchun.zhu@mediatek.com>
> >
> > Add device tree binding documentation for the OV02A10 camera sensor.
> >
> > Signed-off-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
> > ---
> >  .../devicetree/bindings/media/i2c/ov02a10.txt      | 43 ++++++++++++++++++++++
> >  MAINTAINERS                                        |  7 ++++
> >  2 files changed, 50 insertions(+)
> >  create mode 100644
> > Documentation/devicetree/bindings/media/i2c/ov02a10.txt
> >
> > diff --git a/Documentation/devicetree/bindings/media/i2c/ov02a10.txt
> > b/Documentation/devicetree/bindings/media/i2c/ov02a10.txt
> > new file mode 100644
> > index 0000000..d40aa87
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/media/i2c/ov02a10.txt
> > @@ -0,0 +1,43 @@
> > +* Omnivision OV02A10 MIPI CSI-2 sensor
> > +
> > +Required Properties:
> > +- compatible: shall be "ovti,ov02a10"
> > +- clocks: reference to the xvclk input clock
> > +- clock-names: shall be "xvclk"
> > +- avdd-supply: Analog voltage supply, 2.8 volts
> > +- dovdd-supply: Digital I/O voltage supply, 1.8 volts
> > +- dvdd-supply: Digital core voltage supply, 1.8 volts
> > +- reset-gpios: Low active reset gpio
> > +
> > +The device node shall contain one 'port' child node with an
> > +'endpoint' subnode for its digital output video port, in accordance
> > +with the video interface bindings defined in
> > +Documentation/devicetree/bindings/media/video-interfaces.txt.
> > +The endpoint optional property 'data-lanes' shall be "<1>".
> > +
> > +Example:
> > +&i2c4 {
> > +ov02a10: camera-sensor@3d {
> > +compatible = "ovti,ov02a10";
> > +reg = <0x3d>;
> > +pinctrl-names = "default";
> > +pinctrl-0 = <&camera_pins_cam1_mclk_on>;
> > +
> > +clocks = <&topckgen CLK_TOP_MUX_CAMTG2>,
> > +<&topckgen CLK_TOP_UNIVP_192M_D8>;
> > +clock-names = "xvclk", "freq_mux";
> > +
> > +avdd-supply = <&mt6358_vcama1_reg>;
> > +dvdd-supply = <&mt6358_vcn18_reg>;
> > +dovdd-supply = <&mt6358_vcamio_reg>;
> > +pwdn-gpios = <&pio 107 1>;
> 
> Not documented. If you need this, use 'powerdown-gpios' instead.
> 

Fixed in next release.

> > +reset-gpios = <&pio 109 1>;
> > +
> > +port {
> > +   ov02a10_core: endpoint {
> > +       remote-endpoint = <&ov02a10_0>;
> > +   data-lanes = <1>;
> > +};
> > +};
> > +};
> > +};
> > diff --git a/MAINTAINERS b/MAINTAINERS index 5cfbea4..62b81ff 100644
> > --- a/MAINTAINERS
> > +++ b/MAINTAINERS
> > @@ -11571,6 +11571,13 @@ T:git git://linuxtv.org/media_tree.git
> >  S:Maintained
> >  F:drivers/media/i2c/ov13858.c
> >
> > +OMNIVISION OV02A10 SENSOR DRIVER
> > +M:Dongchun Zhu <dongchun.zhu@mediatek.com>
> > +L:linux-media@vger.kernel.org
> > +T:git git://linuxtv.org/media_tree.git
> > +S:Maintained
> > +F:Documentation/devicetree/bindings/media/i2c/ov02a10.txt
> > +
> >  OMNIVISION OV2680 SENSOR DRIVER
> >  M:Rui Miguel Silva <rmfrfs@gmail.com>
> >  L:linux-media@vger.kernel.org
> > --
> > 2.9.2
> >
> 
> _______________________________________________
> Linux-mediatek mailing list
> Linux-mediatek@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-mediatek
> *********************MEDIATEK Confidential/Internal Use*********************



_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: [RFC,V2,2/2] media: i2c: Add Omnivision OV02A10 camera sensor driver
       [not found]     ` <8639e67ad6db40b78e48b00c875187dc@mtkmbs02n1.mediatek.inc>
@ 2019-08-17  5:35       ` Dongchun Zhu
  0 siblings, 0 replies; 11+ messages in thread
From: Dongchun Zhu @ 2019-08-17  5:35 UTC (permalink / raw)
  To: Bingbu Cao
  Cc: mark.rutland, devicetree, drinkcat, srv_heupstream, tfiga,
	shengnan.wang, louis.kuo, sj.huang, robh+dt, linux-mediatek,
	matthias.bgg, bingbu.cao, mchehab, linux-arm-kernel, linux-media


Hi Bingbu,

On Tue, 2019-07-08 at 15:52 +0800, Bingbu Cao wrote:
> -----Original Message-----
> From: Linux-mediatek [mailto:linux-mediatek-bounces@lists.infradead.org] On Behalf Of Bingbu Cao
> Sent: Monday, July 08, 2019 3:53 PM
> To: Dongchun Zhu (朱东春) <Dongchun.Zhu@mediatek.com>; mchehab@kernel.org; robh+dt@kernel.org; mark.rutland@arm.com; sakari.ailus@linux.intel.com; --to=drinkcat@chromium.org; tfiga@chromium.org; matthias.bgg@gmail.com; bingbu.cao@intel.com
> Cc: devicetree@vger.kernel.org; srv_heupstream <srv_heupstream@mediatek.com>; Shengnan Wang (王圣男) <shengnan.wang@mediatek.com>; Sj Huang (黃信璋) <sj.huang@mediatek.com>; linux-mediatek@lists.infradead.org; Louis Kuo (郭德寧) <louis.kuo@mediatek.com>; linux-arm-kernel@lists.infradead.org; linux-media@vger.kernel.org
> Subject: Re: [RFC,V2,2/2] media: i2c: Add Omnivision OV02A10 camera sensor driver
> 
> 
> 
> On 7/4/19 4:46 PM, dongchun.zhu@mediatek.com wrote:
> > From: Dongchun Zhu <dongchun.zhu@mediatek.com>
> >
> > This patch adds a V4L2 sub-device driver for OV02A10 image sensor.
> > The OV02A10 is a 1/5" CMOS sensor from Omnivision.
> > Supports output format: 10-bit Raw.
> > The OV02A10 has a single MIPI lane interface and use the I2C bus for control and the CSI-2 bus for data.
> >
> > Signed-off-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
> >
> snip
> > +
> > +/* MIPI color bar enable output */
> > +static const struct regval ov02a10_test_pattern_enable_regs[] = {
> > +{0xfd, 0x01},
> > +{0x0d, 0x00},
> > +{0xb6, 0x01},
> > +{0x01, 0x01},
> > +{0xfd, 0x01},
> > +{0xac, 0x01},
> > +{REG_NULL, 0x00}
> Actually, you can use ARRAY_SIZE to write the regs, the REG_NULL can be removed. However, it is not a problem.
> ...
> snip...

Thanks for kindly reminder.
It would remain, just as OV5695/OV2685 did.

> > +static int ov02a10_set_fmt(struct v4l2_subdev *sd,
> > +   struct v4l2_subdev_pad_config *cfg,
> > +   struct v4l2_subdev_format *fmt) {
> > +struct ov02a10 *ov02a10 = to_ov02a10(sd);
> > +struct v4l2_mbus_framefmt *mbus_fmt = &fmt->format;
> > +int ret = 0;
> > +
> > +mutex_lock(&ov02a10->mutex);
> > +
> > +if (ov02a10->streaming) {
> > +ret = -EBUSY;
> > +goto unlock;
> I like return -EBUSY directly after mutex_unlock here and return 0 below.

Got it.
Fixed in next release.

> > +}
> > +
> > +/* only one mode supported */
> > +mbus_fmt->code = ov02a10->fmt.code;
> > +ov02a10_fill_fmt(ov02a10->cur_mode, mbus_fmt);
> > +ov02a10->fmt = fmt->format;
> > +
> > +unlock:
> > +mutex_unlock(&ov02a10->mutex);
> > +
> > +return ret;
> > +}
> > +
> > +static int ov02a10_get_fmt(struct v4l2_subdev *sd,
> > +   struct v4l2_subdev_pad_config *cfg,
> > +   struct v4l2_subdev_format *fmt) {
> > +struct ov02a10 *ov02a10 = to_ov02a10(sd);
> > +struct v4l2_mbus_framefmt *mbus_fmt = &fmt->format;
> > +
> > +mutex_lock(&ov02a10->mutex);
> > +
> > +fmt->format = ov02a10->fmt;
> > +mbus_fmt->code = ov02a10->fmt.code;
> > +ov02a10_fill_fmt(ov02a10->cur_mode, mbus_fmt);
> > +
> > +mutex_unlock(&ov02a10->mutex);
> > +
> > +return 0;
> > +}
> > +
> > +static int ov02a10_enum_mbus_code(struct v4l2_subdev *sd,
> > +  struct v4l2_subdev_pad_config *cfg,
> > +  struct v4l2_subdev_mbus_code_enum *code) {
> > +struct ov02a10 *ov02a10 = to_ov02a10(sd);
> > +
> > +if (code->index >= ARRAY_SIZE(supported_modes) || !(code->index))
> > +return -EINVAL;
> > +
> > +code->code = ov02a10->fmt.code;
> > +
> > +return 0;
> > +}
> > +
> > +static int ov02a10_enum_frame_sizes(struct v4l2_subdev *sd,
> > +    struct v4l2_subdev_pad_config *cfg,
> > +    struct v4l2_subdev_frame_size_enum *fse) {
> > +if (fse->index >= ARRAY_SIZE(supported_modes) || !(fse->index))
> > +return -EINVAL;
> > +
> > +fse->min_width  = supported_modes[fse->index].width;
> > +fse->max_width  = supported_modes[fse->index].width;
> > +fse->max_height = supported_modes[fse->index].height;
> > +fse->min_height = supported_modes[fse->index].height;
> > +
> > +return 0;
> > +}
> > +
> > +static int __ov02a10_power_on(struct ov02a10 *ov02a10) {
> > +struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> > +struct device *dev = &client->dev;
> > +int ret;
> > +
> > +ret = clk_prepare_enable(ov02a10->xvclk);
> > +if (ret < 0) {
> > +dev_err(dev, "Failed to enable xvclk\n");
> > +return ret;
> > +}
> > +
> > +/* note: set 0 is high, set 1 is low */
> > +gpiod_set_value_cansleep(ov02a10->reset_gpio, 1);
> > +gpiod_set_value_cansleep(ov02a10->pwdn_gpio, 0);
> > +
> > +ret = regulator_bulk_enable(OV02A10_NUM_SUPPLIES, ov02a10->supplies);
> > +if (ret < 0) {
> > +dev_err(dev, "Failed to enable regulators\n");
> > +goto disable_clk;
> > +}
> > +msleep_range(7);
> > +
> > +gpiod_set_value_cansleep(ov02a10->pwdn_gpio, 1);
> > +msleep_range(10);
> > +
> > +gpiod_set_value_cansleep(ov02a10->reset_gpio, 0);
> > +msleep_range(10);
> > +
> > +return 0;
> > +
> > +disable_clk:
> > +clk_disable_unprepare(ov02a10->xvclk);
> > +
> > +return ret;
> > +}
> > +
> > +static void __ov02a10_power_off(struct ov02a10 *ov02a10) {
> > +clk_disable_unprepare(ov02a10->xvclk);
> > +gpiod_set_value_cansleep(ov02a10->reset_gpio, 1);
> > +gpiod_set_value_cansleep(ov02a10->pwdn_gpio, 1);
> > +regulator_bulk_disable(OV02A10_NUM_SUPPLIES, ov02a10->supplies); }
> > +
> > +static int __ov02a10_start_stream(struct ov02a10 *ov02a10) {
> > +struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> > +int ret;
> > +
> > +/* Apply default values of current mode */
> > +ret = ov02a10_write_array(ov02a10, ov02a10->cur_mode->reg_list);
> > +if (ret)
> > +return ret;
> > +
> > +/* Apply customized values from user */
> > +ret = __v4l2_ctrl_handler_setup(ov02a10->subdev.ctrl_handler);
> > +if (ret)
> > +return ret;
> > +
> > +/* Set Orientation be 180 degree */
> Set orientation to 180 degree

Got it.
Fixed in next release.

> > +if (ov02a10->upside_down) {
> > +ret = ov02a10_write_reg(ov02a10, REG_MIRROR_FLIP_CONTROL,
> > +REG_CONFIG_MIRROR_FLIP);
> > +if (ret) {
> > +dev_err(&client->dev, "%s failed to set orientation\n",
> > +__func__);
> > +return ret;
> > +}
> > +ret = ov02a10_write_reg(ov02a10, REG_GLOBAL_EFFECTIVE,
> > +REG_ENABLE);
> > +if (ret < 0)
> > +return ret;
> > +}
> > +
> > +/* set stream on register */
> > +return ov02a10_write_reg(ov02a10,
> > + REG_SC_CTRL_MODE, SC_CTRL_MODE_STREAMING); }
> > +
> > +static int __ov02a10_stop_stream(struct ov02a10 *ov02a10) {
> > +return ov02a10_write_reg(ov02a10,
> > + REG_SC_CTRL_MODE, SC_CTRL_MODE_STANDBY); }
> > +
> > +static int ov02a10_entity_init_cfg(struct v4l2_subdev *subdev,
> > +   struct v4l2_subdev_pad_config *cfg) {
> > +struct v4l2_subdev_format fmt = { 0 };
> > +
> > +fmt.which = cfg ? V4L2_SUBDEV_FORMAT_TRY : V4L2_SUBDEV_FORMAT_ACTIVE;
> > +fmt.format.width = 1600;
> > +fmt.format.height = 1200;
> > +
> > +ov02a10_set_fmt(subdev, cfg, &fmt);
> > +
> > +return 0;
> > +}
> > +
> > +static int ov02a10_s_stream(struct v4l2_subdev *sd, int on) {
> > +struct ov02a10 *ov02a10 = to_ov02a10(sd);
> > +struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> > +int ret = 0;
> > +
> > +dev_dbg(&client->dev, "ov02a10 s_stream (%d)\n", on);
> > +mutex_lock(&ov02a10->mutex);
> > +
> > +if (ov02a10->streaming == on)
> > +goto unlock_and_return;
> > +
> > +if (on) {
> > +ret = pm_runtime_get_sync(&client->dev);
> > +if (ret < 0) {
> > +pm_runtime_put_noidle(&client->dev);
> > +goto unlock_and_return;
> > +}
> > +
> > +ret = __ov02a10_start_stream(ov02a10);
> > +if (ret) {
> > +__ov02a10_stop_stream(ov02a10);
> > +ov02a10->streaming = !on;
> > +goto err_rpm_put;
> > +}
> > +} else {
> > +__ov02a10_stop_stream(ov02a10);
> > +pm_runtime_put(&client->dev);
> > +}
> > +
> > +ov02a10->streaming = on;
> > +mutex_unlock(&ov02a10->mutex);
> > +
> > +return ret;
> > +
> > +err_rpm_put:
> > +pm_runtime_put(&client->dev);
> > +unlock_and_return:
> > +mutex_unlock(&ov02a10->mutex);
> > +
> > +return ret;
> > +}
> > +
> > +static int ov02a10_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh
> > +*fh) {
> > +struct ov02a10 *ov02a10 = to_ov02a10(sd);
> > +struct v4l2_mbus_framefmt *try_fmt = v4l2_subdev_get_try_format(sd,
> > +fh->pad,
> > +0);
> > +
> > +mutex_lock(&ov02a10->mutex);
> > +/* Initialize try_fmt */
> > +try_fmt->code = ov02a10->fmt.code;
> > +ov02a10_fill_fmt(&supported_modes[0], try_fmt);
> > +
> > +mutex_unlock(&ov02a10->mutex);
> > +
> > +return 0;
> > +}
> > +
> > +static int __maybe_unused ov02a10_runtime_resume(struct device *dev)
> > +{
> > +struct i2c_client *client = to_i2c_client(dev);
> > +struct v4l2_subdev *sd = i2c_get_clientdata(client);
> > +struct ov02a10 *ov02a10 = to_ov02a10(sd);
> > +
> > +return __ov02a10_power_on(ov02a10);
> > +}
> > +
> > +static int __maybe_unused ov02a10_runtime_suspend(struct device *dev)
> > +{
> > +struct i2c_client *client = to_i2c_client(dev);
> > +struct v4l2_subdev *sd = i2c_get_clientdata(client);
> > +struct ov02a10 *ov02a10 = to_ov02a10(sd);
> > +
> > +__ov02a10_power_off(ov02a10);
> > +
> > +return 0;
> > +}
> > +
> > +static const struct dev_pm_ops ov02a10_pm_ops = {
> > +SET_RUNTIME_PM_OPS(ov02a10_runtime_suspend,
> > +   ov02a10_runtime_resume, NULL)
> > +};
> > +
> > +static int ov02a10_set_test_pattern(struct ov02a10 *ov02a10, s32
> > +value) {
> > +if (value)
> > +return ov02a10_write_array(ov02a10,
> > +   ov02a10_test_pattern_enable_regs);
> > +
> > +return ov02a10_write_array(ov02a10,
> > +ov02a10_test_pattern_disable_regs);
> > +}
> > +
> > +static int ov02a10_set_ctrl(struct v4l2_ctrl *ctrl) {
> > +struct ov02a10 *ov02a10 = container_of(ctrl->handler,
> > +     struct ov02a10, ctrl_handler);
> > +struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> > +s64 max_expo;
> > +int ret;
> > +
> > +/* Propagate change of current control to all related controls */
> > +if (ctrl->id == V4L2_CID_VBLANK) {
> > +/* Update max exposure while meeting expected vblanking */
> > +max_expo = ov02a10->cur_mode->height + ctrl->val - 4;
> > +__v4l2_ctrl_modify_range(ov02a10->exposure,
> > + ov02a10->exposure->minimum, max_expo,
> > + ov02a10->exposure->step,
> > + ov02a10->exposure->default_value);
> > +}
> > +
> > +/* V4L2 controls values will be applied only when power is already up */
> > +if (!pm_runtime_get_if_in_use(&client->dev))
> > +return 0;
> > +
> > +switch (ctrl->id) {
> > +case V4L2_CID_EXPOSURE:
> > +ret = ov02a10_write_reg(ov02a10, REG_PAGE_SWITCH, REG_ENABLE);
> > +if (ret < 0)
> > +return ret;
> > +ret = ov02a10_write_reg(ov02a10, OV02A10_REG_EXPOSURE_H,
> > +((ctrl->val >> 8) & 0xFF));
> > +if (!ret) {
> > +ret = ov02a10_write_reg(ov02a10, OV02A10_REG_EXPOSURE_L,
> > +(ctrl->val & 0xFF));
> > +if (ret < 0)
> > +return ret;
> > +}
> > +ret = ov02a10_write_reg(ov02a10, REG_GLOBAL_EFFECTIVE,
> > +REG_ENABLE);
> > +if (ret < 0)
> > +return ret;
> > +break;
> > +case V4L2_CID_ANALOGUE_GAIN:
> > +ret = ov02a10_write_reg(ov02a10, REG_PAGE_SWITCH, REG_ENABLE);
> > +if (ret < 0)
> > +return ret;
> > +ret = ov02a10_write_reg(ov02a10, OV02A10_REG_GAIN,
> > +(ctrl->val & 0xFF));
> > +if (ret < 0)
> > +return ret;
> > +ret = ov02a10_write_reg(ov02a10, REG_GLOBAL_EFFECTIVE,
> > +REG_ENABLE);
> > +if (ret < 0)
> > +return ret;
> > +break;
> > +case V4L2_CID_VBLANK:
> > +ret = ov02a10_write_reg(ov02a10, REG_PAGE_SWITCH, REG_ENABLE);
> > +if (ret < 0)
> > +return ret;
> > +ret = ov02a10_write_reg(ov02a10, OV02A10_REG_VTS_H,
> > +(((ctrl->val +
> > +ov02a10->cur_mode->height - 1224) >> 8)
> > +& 0xFF));
> 1224 is hard-coded here, could you add some comments? Is it a sensor setting sensitive value?

This would be fixed in next release.
1224 is the basic line for OV02a10 CMOS sensor.
In fact, there is one relationship between framelength and v-blanking.
That is, framelength = basic_line + v-blanking.
Thus we could modify the value of v-blanking register to update
framelength.

> > +if (!ret) {
> > +ret = ov02a10_write_reg(ov02a10, OV02A10_REG_VTS_L,
> > +((ctrl->val +
> > +ov02a10->cur_mode->height -
> > +1224) & 0xFF));
> ditto.

Fixed in next release.

> > +if (ret < 0)
> > +return ret;
> > +}
> > +ret = ov02a10_write_reg(ov02a10, REG_GLOBAL_EFFECTIVE,
> > +REG_ENABLE);
> > +if (ret < 0)
> > +return ret;
> > +break;
> > +case V4L2_CID_TEST_PATTERN:
> > +ret = ov02a10_set_test_pattern(ov02a10, ctrl->val);
> > +if (ret < 0)
> > +return ret;
> > +break;
> > +default:
> > +dev_warn(&client->dev, "%s Unhandled id:0x%x, val:0x%x\n",
> > + __func__, ctrl->id, ctrl->val);
> > +ret = -EINVAL;
> > +break;
> > +};
> > +
> > +pm_runtime_put(&client->dev);
> > +
> > +return ret;
> > +}
> > +
> > +static const struct v4l2_subdev_video_ops ov02a10_video_ops = {
> > +.s_stream = ov02a10_s_stream,
> > +};
> > +
> > +static const struct v4l2_subdev_pad_ops ov02a10_pad_ops = {
> > +.init_cfg = ov02a10_entity_init_cfg,
> > +.enum_mbus_code = ov02a10_enum_mbus_code,
> > +.enum_frame_size = ov02a10_enum_frame_sizes,
> > +.get_fmt = ov02a10_get_fmt,
> > +.set_fmt = ov02a10_set_fmt,
> > +};
> > +
> > +static const struct v4l2_subdev_ops ov02a10_subdev_ops = {
> > +.video= &ov02a10_video_ops,
> > +.pad= &ov02a10_pad_ops,
> > +};
> > +
> > +static const struct media_entity_operations ov02a10_subdev_entity_ops = {
> > +.link_validate = v4l2_subdev_link_validate, };
> > +
> > +static const struct v4l2_subdev_internal_ops ov02a10_internal_ops = {
> > +.open = ov02a10_open,
> > +};
> > +
> > +static const struct v4l2_ctrl_ops ov02a10_ctrl_ops = {
> > +.s_ctrl = ov02a10_set_ctrl,
> > +};
> > +
> > +static int ov02a10_initialize_controls(struct ov02a10 *ov02a10) {
> > +struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> > +const struct ov02a10_mode *mode;
> > +struct v4l2_ctrl_handler *handler;
> > +struct v4l2_ctrl *ctrl;
> > +u64 exposure_max;
> > +u32 pixel_rate, h_blank;
> > +int ret;
> > +
> > +handler = &ov02a10->ctrl_handler;
> > +mode = ov02a10->cur_mode;
> > +ret = v4l2_ctrl_handler_init(handler, 10);
> > +if (ret)
> > +return ret;
> > +handler->lock = &ov02a10->mutex;
> > +
> > +ctrl = v4l2_ctrl_new_int_menu(handler, NULL, V4L2_CID_LINK_FREQ,
> > +      0, 0, link_freq_menu_items);
> > +if (ctrl)
> > +ctrl->flags |= V4L2_CTRL_FLAG_READ_ONLY;
> > +
> > +pixel_rate = (link_freq_menu_items[0] * 2 * OV02A10_LANES) /
> > +     OV02A10_BITS_PER_SAMPLE;
> > +v4l2_ctrl_new_std(handler, NULL, V4L2_CID_PIXEL_RATE,
> > +  0, pixel_rate, 1, pixel_rate);
> > +
> > +h_blank = mode->hts_def - mode->width;
> > +ov02a10->hblank = v4l2_ctrl_new_std(handler, NULL, V4L2_CID_HBLANK,
> > +    h_blank, h_blank, 1, h_blank);
> > +if (ov02a10->hblank)
> > +ov02a10->hblank->flags |= V4L2_CTRL_FLAG_READ_ONLY;
> > +
> > +ov02a10->vblank = v4l2_ctrl_new_std(handler, &ov02a10_ctrl_ops,
> > +    V4L2_CID_VBLANK, mode->vts_def -
> > +    mode->height,
> > +    OV02A10_VTS_MAX - mode->height, 1,
> > +    mode->vts_def - mode->height);
> > +
> > +exposure_max = mode->vts_def - 4;
> > +ov02a10->exposure = v4l2_ctrl_new_std(handler, &ov02a10_ctrl_ops,
> > +      V4L2_CID_EXPOSURE,
> > +      OV02A10_EXPOSURE_MIN,
> > +      exposure_max,
> > +      OV02A10_EXPOSURE_STEP,
> > +      mode->exp_def);
> > +
> > +ov02a10->anal_gain = v4l2_ctrl_new_std(handler, &ov02a10_ctrl_ops,
> > +       V4L2_CID_ANALOGUE_GAIN,
> > +       OV02A10_GAIN_MIN,
> > +       OV02A10_GAIN_MAX,
> > +       OV02A10_GAIN_STEP,
> > +       OV02A10_GAIN_DEFAULT);
> > +
> > +ov02a10->test_pattern =
> > +   v4l2_ctrl_new_std_menu_items(handler,
> > +&ov02a10_ctrl_ops,
> > +V4L2_CID_TEST_PATTERN,
> > +ARRAY_SIZE(ov02a10_test_pattern_menu) -
> > +1, 0, 0, ov02a10_test_pattern_menu);
> > +
> > +if (handler->error) {
> > +ret = handler->error;
> > +dev_err(&client->dev,
> > +"Failed to init controls(%d)\n", ret);
> > +goto err_free_handler;
> > +}
> > +
> > +ov02a10->subdev.ctrl_handler = handler;
> > +
> > +return 0;
> > +
> > +err_free_handler:
> > +v4l2_ctrl_handler_free(handler);
> > +
> > +return ret;
> > +}
> > +
> > +static int ov02a10_check_sensor_id(struct ov02a10 *ov02a10) {
> > +struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> > +u16 id;
> > +u8 pid = 0;
> > +u8 ver = 0;
> > +int ret;
> > +
> > +/* Check sensor revision */
> > +ret = ov02a10_read_reg(ov02a10, OV02A10_REG_CHIP_ID_H, &pid);
> > +if (ret)
> > +return ret;
> > +
> > +ret = ov02a10_read_reg(ov02a10, OV02A10_REG_CHIP_ID_L, &ver);
> > +if (ret)
> > +return ret;
> > +
> > +id = OV02A10_ID(pid, ver);
> > +if (id != CHIP_ID) {
> > +dev_err(&client->dev, "Unexpected sensor id(%04x)\n", id);
> > +return ret;
> > +}
> > +dev_dbg(&client->dev, "Detected OV%04X sensor\n", id);
> > +
> > +return 0;
> > +}
> > +
> > +static int ov02a10_configure_regulators(struct ov02a10 *ov02a10) {
> > +struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> > +unsigned int i;
> > +
> > +for (i = 0; i < OV02A10_NUM_SUPPLIES; i++)
> > +ov02a10->supplies[i].supply = ov02a10_supply_names[i];
> > +
> > +return devm_regulator_bulk_get(&client->dev,
> > +       OV02A10_NUM_SUPPLIES,
> > +       ov02a10->supplies);
> > +}
> > +
> > +static int ov02a10_probe(struct i2c_client *client) {
> > +struct device *dev = &client->dev;
> > +struct ov02a10 *ov02a10;
> > +u32 rotation;
> > +u32 xclk_freq;
> > +int ret;
> > +
> > +dev_dbg(dev, "ov02a10 probe\n");
> I think this line is not needed at all.

Removed in next release.

> > +ov02a10 = devm_kzalloc(dev, sizeof(*ov02a10), GFP_KERNEL);
> > +if (!ov02a10)
> > +return -ENOMEM;
> > +
> > +v4l2_i2c_subdev_init(&ov02a10->subdev, client, &ov02a10_subdev_ops);
> > +ov02a10->fmt.code = MEDIA_BUS_FMT_SBGGR10_1X10;
> > +
> > +/* optional indication of physical rotation of sensor */
> > +ret = fwnode_property_read_u32(dev_fwnode(dev), "rotation",
> > +       &rotation);
> > +if (!ret) {
> > +switch (rotation) {
> > +case 180:
> > +ov02a10->upside_down = true;
> > +ov02a10->fmt.code = MEDIA_BUS_FMT_SRGGB10_1X10;
> > +break;
> > +case 0:
> > +break;
> > +default:
> > +dev_warn(dev, "%u degrees rotation is not supported, ignoring...\n",
> > + rotation);
> > +}
> > +}
> > +
> > +/* get system clock (xvclk) */
> > +ov02a10->xvclk = devm_clk_get(dev, "xvclk");
> > +if (IS_ERR(ov02a10->xvclk)) {
> > +dev_err(dev, "Failed to get xvclk\n");
> > +return -EINVAL;
> > +}
> > +
> > +ret = of_property_read_u32(dev->of_node, "clock-frequency", &xclk_freq);
> > +if (ret) {
> > +dev_err(dev, "Failed to get xclk frequency\n");
> > +return ret;
> > +}
> > +
> > +/* external clock must be 24MHz, allow 1% tolerance */
> > +if (xclk_freq < 23760000 || xclk_freq > 24240000) {
> > +dev_err(dev, "external clock frequency %u is not supported\n",
> > +xclk_freq);
> > +return -EINVAL;
> > +}
> > +dev_dbg(dev, "external clock frequency %u\n", xclk_freq);
> > +
> > +ret = clk_set_rate(ov02a10->xvclk, xclk_freq);
> > +if (ret) {
> > +dev_err(dev, "Failed to set xvclk frequency (24MHz)\n");
> > +return ret;
> > +}
> > +
> > +ov02a10->pwdn_gpio = devm_gpiod_get(dev, "pwdn", GPIOD_OUT_LOW);
> > +if (IS_ERR(ov02a10->pwdn_gpio)) {
> > +dev_err(dev, "Failed to get powerdown-gpios\n");
> > +return -EINVAL;
> > +}
> > +
> > +ov02a10->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
> > +if (IS_ERR(ov02a10->reset_gpio)) {
> > +dev_err(dev, "Failed to get reset-gpios\n");
> > +return -EINVAL;
> > +}
> > +
> > +ret = ov02a10_configure_regulators(ov02a10);
> > +if (ret) {
> > +dev_err(dev, "Failed to get power regulators\n");
> > +return ret;
> > +}
> > +
> > +mutex_init(&ov02a10->mutex);
> > +ov02a10->cur_mode = &supported_modes[0];
> > +ret = ov02a10_initialize_controls(ov02a10);
> > +if (ret) {
> > +dev_err(dev, "Failed to initialize controls\n");
> > +goto err_destroy_mutex;
> > +}
> > +
> > +ret = __ov02a10_power_on(ov02a10);
> > +if (ret)
> > +goto err_free_handler;
> > +
> > +ret = ov02a10_check_sensor_id(ov02a10);
> > +if (ret)
> > +goto err_power_off;
> > +
> > +ov02a10->subdev.internal_ops = &ov02a10_internal_ops;
> > +ov02a10->subdev.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
> > +ov02a10->subdev.entity.ops = &ov02a10_subdev_entity_ops;
> > +ov02a10->subdev.entity.function = MEDIA_ENT_F_CAM_SENSOR;
> > +ov02a10->pad.flags = MEDIA_PAD_FL_SOURCE;
> > +ret = media_entity_pads_init(&ov02a10->subdev.entity, 1, &ov02a10->pad);
> > +if (ret < 0) {
> > +dev_err(dev, "failed to init entity pads: %d", ret);
> > +goto err_power_off;
> > +}
> > +
> > +ret = v4l2_async_register_subdev(&ov02a10->subdev);
> > +if (ret) {
> > +dev_err(dev, "failed to register V4L2 subdev: %d",
> > +ret);
> > +goto err_clean_entity;
> > +}
> > +
> > +pm_runtime_set_active(dev);
> > +pm_runtime_enable(dev);
> > +pm_runtime_idle(dev);
> > +
> > +return 0;
> > +
> > +err_clean_entity:
> > +media_entity_cleanup(&ov02a10->subdev.entity);
> > +err_power_off:
> > +__ov02a10_power_off(ov02a10);
> > +err_free_handler:
> > +v4l2_ctrl_handler_free(ov02a10->subdev.ctrl_handler);
> > +err_destroy_mutex:
> > +mutex_destroy(&ov02a10->mutex);
> > +
> > +return ret;
> > +}
> > +
> > +static int ov02a10_remove(struct i2c_client *client) {
> > +struct v4l2_subdev *sd = i2c_get_clientdata(client);
> > +struct ov02a10 *ov02a10 = to_ov02a10(sd);
> > +
> > +v4l2_async_unregister_subdev(sd);
> > +media_entity_cleanup(&sd->entity);
> > +v4l2_ctrl_handler_free(sd->ctrl_handler);
> > +pm_runtime_disable(&client->dev);
> > +if (!pm_runtime_status_suspended(&client->dev))
> > +__ov02a10_power_off(ov02a10);
> > +pm_runtime_set_suspended(&client->dev);
> > +mutex_destroy(&ov02a10->mutex);
> > +
> > +return 0;
> > +}
> > +
> > +#if IS_ENABLED(CONFIG_OF)
> > +static const struct of_device_id ov02a10_of_match[] = {
> > +{ .compatible = "ovti,ov02a10" },
> > +{},
> > +};
> > +MODULE_DEVICE_TABLE(of, ov02a10_of_match); #endif
> > +
> > +static struct i2c_driver ov02a10_i2c_driver = {
> > +.driver = {
> > +.name = "ov02a10",
> > +.pm = &ov02a10_pm_ops,
> > +.of_match_table = ov02a10_of_match,
> > +},
> > +.probe_new= &ov02a10_probe,
> > +.remove= &ov02a10_remove,
> > +};
> > +
> > +module_i2c_driver(ov02a10_i2c_driver);
> > +
> > +MODULE_AUTHOR("Dongchun Zhu <dongchun.zhu@mediatek.com>");
> > +MODULE_DESCRIPTION("OmniVision OV02A10 sensor driver");
> > +MODULE_LICENSE("GPL v2");
> > +
> >
> Other part looks good to me.

Many thanks for your review.
I really appreciate the effort you all made for the work.

> 
> _______________________________________________
> Linux-mediatek mailing list
> Linux-mediatek@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-mediatek
> *********************MEDIATEK Confidential/Internal Use*********************



_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: [RFC,V2,1/2] media: dt-bindings: media: i2c: Add bindings for OV02A10
  2019-08-17  3:53       ` Dongchun Zhu
@ 2019-08-17 21:32         ` Sakari Ailus
  2019-08-19  5:39           ` Dongchun Zhu
  0 siblings, 1 reply; 11+ messages in thread
From: Sakari Ailus @ 2019-08-17 21:32 UTC (permalink / raw)
  To: Dongchun Zhu
  Cc: mark.rutland, devicetree, drinkcat, srv_heupstream, menghui.lin,
	tfiga, shengnan.wang, louis.kuo, sj.huang, robh+dt,
	linux-mediatek, matthias.bgg, bingbu.cao, mchehab,
	linux-arm-kernel, linux-media

Hi Dongchun,

On Sat, Aug 17, 2019 at 11:53:05AM +0800, Dongchun Zhu wrote:
...
> > > +
> > > +The device node shall contain one 'port' child node with an
> > > +'endpoint' subnode for its digital output video port, in accordance
> > > +with the video interface bindings defined in
> > > +Documentation/devicetree/bindings/media/video-interfaces.txt.
> > > +The endpoint optional property 'data-lanes' shall be "<1>".
> > 
> > How many lanes does the module (or the sensor) have?
> > 
> 
> From sensor datasheet, OV02A10 supports 1-lane MIPI interface.

If only one lane is supported, the property should be omitted: there's
nothing that the driver needs to know here.

-- 
Sakari Ailus

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: [RFC,V2,1/2] media: dt-bindings: media: i2c: Add bindings for OV02A10
  2019-08-17 21:32         ` Sakari Ailus
@ 2019-08-19  5:39           ` Dongchun Zhu
  0 siblings, 0 replies; 11+ messages in thread
From: Dongchun Zhu @ 2019-08-19  5:39 UTC (permalink / raw)
  To: Sakari Ailus
  Cc: mark.rutland, devicetree, drinkcat, srv_heupstream, tfiga,
	shengnan.wang, louis.kuo, sj.huang, robh+dt, linux-mediatek,
	matthias.bgg, bingbu.cao, mchehab, linux-arm-kernel, linux-media

Hi Sakari,

On Sun, 2019-08-18 at 00:32 +0300, Sakari Ailus wrote:
> Hi Dongchun,
> 
> On Sat, Aug 17, 2019 at 11:53:05AM +0800, Dongchun Zhu wrote:
> ...
> > > > +
> > > > +The device node shall contain one 'port' child node with an
> > > > +'endpoint' subnode for its digital output video port, in accordance
> > > > +with the video interface bindings defined in
> > > > +Documentation/devicetree/bindings/media/video-interfaces.txt.
> > > > +The endpoint optional property 'data-lanes' shall be "<1>".
> > > 
> > > How many lanes does the module (or the sensor) have?
> > > 
> > 
> > From sensor datasheet, OV02A10 supports 1-lane MIPI interface.
> 
> If only one lane is supported, the property should be omitted: there's
> nothing that the driver needs to know here.
> 
Thanks for the suggestion.
But sorry that I didn't read this message this morning, so this issue
still remains unsettled in v3.
https://patchwork.kernel.org/patch/11100219/
I would fix this point in v4.


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 11+ messages in thread

end of thread, other threads:[~2019-08-19  5:39 UTC | newest]

Thread overview: 11+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-07-04  8:46 [RFC,V2,0/2] media: add support for OV02A10 sensor dongchun.zhu
2019-07-04  8:46 ` [RFC, V2, 1/2] media: dt-bindings: media: i2c: Add bindings for OV02A10 dongchun.zhu
2019-07-22 23:49   ` [RFC,V2,1/2] " Rob Herring
     [not found]     ` <5d5d644af9334609bb7c3ff745b2e754@mtkmbs02n1.mediatek.inc>
2019-08-17  5:03       ` Dongchun Zhu
2019-07-23  7:41   ` Sakari Ailus
     [not found]     ` <ef65288c523f405396991bd6d757bba0@mtkmbs02n1.mediatek.inc>
2019-08-17  3:53       ` Dongchun Zhu
2019-08-17 21:32         ` Sakari Ailus
2019-08-19  5:39           ` Dongchun Zhu
2019-07-04  8:46 ` [RFC,V2,2/2] media: i2c: Add Omnivision OV02A10 camera sensor driver dongchun.zhu
2019-07-08  7:52   ` Bingbu Cao
     [not found]     ` <8639e67ad6db40b78e48b00c875187dc@mtkmbs02n1.mediatek.inc>
2019-08-17  5:35       ` Dongchun Zhu

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).