Linux-ARM-Kernel Archive on lore.kernel.org
 help / color / Atom feed
From: Miquel Raynal <miquel.raynal@bootlin.com>
To: Gregory Clement <gregory.clement@bootlin.com>,
	Jason Cooper <jason@lakedaemon.net>, Andrew Lunn <andrew@lunn.ch>,
	Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>,
	Kishon Vijay Abraham I <kishon@ti.com>
Cc: devicetree@vger.kernel.org,
	Antoine Tenart <antoine.tenart@bootlin.com>,
	Grzegorz Jaszczyk <jaz@semihalf.com>,
	Russell King <linux@armlinux.org.uk>,
	Maxime Chevallier <maxime.chevallier@bootlin.com>,
	Nadav Haklai <nadavh@marvell.com>,
	Rob Herring <robh+dt@kernel.org>,
	Thomas Petazzoni <thomas.petazzoni@bootlin.com>,
	Miquel Raynal <miquel.raynal@bootlin.com>,
	linux-arm-kernel@lists.infradead.org
Subject: [PATCH v3 11/19] phy: mvebu-cp110-comphy: Add PCIe support
Date: Wed, 31 Jul 2019 14:21:18 +0200
Message-ID: <20190731122126.3049-12-miquel.raynal@bootlin.com> (raw)
In-Reply-To: <20190731122126.3049-1-miquel.raynal@bootlin.com>

From: Grzegorz Jaszczyk <jaz@semihalf.com>

Add PCIe support by filling the COMPHY modes table.

Also add a new macro to generate the right value for the firmware
depending on the width (PCI x1, x2, x4, etc). The width will be passed
by the core as the "submode" argument of the ->set_mode() callback. If
this argument is zero, default to x1 mode.

Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 drivers/phy/marvell/phy-mvebu-cp110-comphy.c | 37 +++++++++++++++++---
 1 file changed, 32 insertions(+), 5 deletions(-)

diff --git a/drivers/phy/marvell/phy-mvebu-cp110-comphy.c b/drivers/phy/marvell/phy-mvebu-cp110-comphy.c
index c61469ed7cbe..076b2bfa8e7b 100644
--- a/drivers/phy/marvell/phy-mvebu-cp110-comphy.c
+++ b/drivers/phy/marvell/phy-mvebu-cp110-comphy.c
@@ -128,6 +128,7 @@
  * [ 5-11]: COMPHY port index
  * [12-16]: COMPHY mode
  * [17]: Clock source
+ * [18-20]: PCIe width (x1, x2, x4)
  */
 #define COMPHY_FW_POL_OFFSET	0
 #define COMPHY_FW_POL_MASK	GENMASK(1, 0)
@@ -142,24 +143,31 @@
 #define COMPHY_FW_PORT_MASK	GENMASK(11, 8)
 #define COMPHY_FW_MODE_OFFSET	12
 #define COMPHY_FW_MODE_MASK	GENMASK(16, 12)
+#define COMPHY_FW_WIDTH_OFFSET	18
+#define COMPHY_FW_WIDTH_MASK	GENMASK(20, 18)
 
-#define COMPHY_FW_PARAM_FULL(mode, port, speed, pol)			\
+#define COMPHY_FW_PARAM_FULL(mode, port, speed, pol, width)		\
 	((((pol) << COMPHY_FW_POL_OFFSET) & COMPHY_FW_POL_MASK) |	\
 	 (((mode) << COMPHY_FW_MODE_OFFSET) & COMPHY_FW_MODE_MASK) |	\
 	 (((port) << COMPHY_FW_PORT_OFFSET) & COMPHY_FW_PORT_MASK) |	\
-	 (((speed) << COMPHY_FW_SPEED_OFFSET) & COMPHY_FW_SPEED_MASK))
+	 (((speed) << COMPHY_FW_SPEED_OFFSET) & COMPHY_FW_SPEED_MASK) |	\
+	 (((width) << COMPHY_FW_WIDTH_OFFSET) & COMPHY_FW_WIDTH_MASK))
 
 #define COMPHY_FW_PARAM(mode, port)					\
-	COMPHY_FW_PARAM_FULL(mode, port, 0, 0)
+	COMPHY_FW_PARAM_FULL(mode, port, COMPHY_FW_SPEED_MAX, 0, 0)
 
 #define COMPHY_FW_PARAM_ETH(mode, port, speed)				\
-	COMPHY_FW_PARAM_FULL(mode, port, speed, 0)
+	COMPHY_FW_PARAM_FULL(mode, port, speed, 0, 0)
+
+#define COMPHY_FW_PARAM_PCIE(mode, port, width)				\
+	COMPHY_FW_PARAM_FULL(mode, port, COMPHY_FW_SPEED_5000, 0, width)
 
 #define COMPHY_FW_MODE_SATA		0x1
 #define COMPHY_FW_MODE_SGMII		0x2 /* SGMII 1G */
 #define COMPHY_FW_MODE_HS_SGMII		0x3 /* SGMII 2.5G */
 #define COMPHY_FW_MODE_USB3H		0x4
 #define COMPHY_FW_MODE_USB3D		0x5
+#define COMPHY_FW_MODE_PCIE		0x6
 #define COMPHY_FW_MODE_RXAUI		0x7
 #define COMPHY_FW_MODE_XFI		0x8 /* SFI: 0x9 (is treated like XFI) */
 
@@ -194,6 +202,7 @@ struct mvebu_comphy_conf {
 
 static const struct mvebu_comphy_conf mvebu_comphy_cp110_modes[] = {
 	/* lane 0 */
+	GEN_CONF(0, 0, PHY_MODE_PCIE, COMPHY_FW_MODE_PCIE),
 	ETH_CONF(0, 1, PHY_INTERFACE_MODE_SGMII, 0x1, COMPHY_FW_MODE_SGMII),
 	ETH_CONF(0, 1, PHY_INTERFACE_MODE_2500BASEX, 0x1, COMPHY_FW_MODE_HS_SGMII),
 	GEN_CONF(0, 1, PHY_MODE_SATA, COMPHY_FW_MODE_SATA),
@@ -201,6 +210,7 @@ static const struct mvebu_comphy_conf mvebu_comphy_cp110_modes[] = {
 	GEN_CONF(1, 0, PHY_MODE_USB_HOST_SS, COMPHY_FW_MODE_USB3H),
 	GEN_CONF(1, 0, PHY_MODE_USB_DEVICE_SS, COMPHY_FW_MODE_USB3D),
 	GEN_CONF(1, 0, PHY_MODE_SATA, COMPHY_FW_MODE_SATA),
+	GEN_CONF(1, 0, PHY_MODE_PCIE, COMPHY_FW_MODE_PCIE),
 	ETH_CONF(1, 2, PHY_INTERFACE_MODE_SGMII, 0x1, COMPHY_FW_MODE_SGMII),
 	ETH_CONF(1, 2, PHY_INTERFACE_MODE_2500BASEX, 0x1, COMPHY_FW_MODE_HS_SGMII),
 	/* lane 2 */
@@ -210,7 +220,9 @@ static const struct mvebu_comphy_conf mvebu_comphy_cp110_modes[] = {
 	ETH_CONF(2, 0, PHY_INTERFACE_MODE_10GKR, 0x1, COMPHY_FW_MODE_XFI),
 	GEN_CONF(2, 0, PHY_MODE_USB_HOST_SS, COMPHY_FW_MODE_USB3H),
 	GEN_CONF(2, 0, PHY_MODE_SATA, COMPHY_FW_MODE_SATA),
+	GEN_CONF(2, 0, PHY_MODE_PCIE, COMPHY_FW_MODE_PCIE),
 	/* lane 3 */
+	GEN_CONF(3, 0, PHY_MODE_PCIE, COMPHY_FW_MODE_PCIE),
 	ETH_CONF(3, 1, PHY_INTERFACE_MODE_SGMII, 0x2, COMPHY_FW_MODE_SGMII),
 	ETH_CONF(3, 1, PHY_INTERFACE_MODE_2500BASEX, 0x2, COMPHY_FW_MODE_HS_SGMII),
 	ETH_CONF(3, 1, PHY_INTERFACE_MODE_RXAUI, -1, COMPHY_FW_MODE_RXAUI),
@@ -223,6 +235,7 @@ static const struct mvebu_comphy_conf mvebu_comphy_cp110_modes[] = {
 	ETH_CONF(4, 0, PHY_INTERFACE_MODE_RXAUI, -1, COMPHY_FW_MODE_RXAUI),
 	GEN_CONF(4, 0, PHY_MODE_USB_DEVICE_SS, COMPHY_FW_MODE_USB3D),
 	GEN_CONF(4, 1, PHY_MODE_USB_HOST_SS, COMPHY_FW_MODE_USB3H),
+	GEN_CONF(4, 1, PHY_MODE_PCIE, COMPHY_FW_MODE_PCIE),
 	ETH_CONF(4, 1, PHY_INTERFACE_MODE_SGMII, 0x1, COMPHY_FW_MODE_SGMII),
 	ETH_CONF(4, 1, PHY_INTERFACE_MODE_2500BASEX, -1, COMPHY_FW_MODE_HS_SGMII),
 	ETH_CONF(4, 1, PHY_INTERFACE_MODE_10GKR, -1, COMPHY_FW_MODE_XFI),
@@ -231,6 +244,7 @@ static const struct mvebu_comphy_conf mvebu_comphy_cp110_modes[] = {
 	GEN_CONF(5, 1, PHY_MODE_SATA, COMPHY_FW_MODE_SATA),
 	ETH_CONF(5, 2, PHY_INTERFACE_MODE_SGMII, 0x1, COMPHY_FW_MODE_SGMII),
 	ETH_CONF(5, 2, PHY_INTERFACE_MODE_2500BASEX, 0x1, COMPHY_FW_MODE_HS_SGMII),
+	GEN_CONF(5, 2, PHY_MODE_PCIE, COMPHY_FW_MODE_PCIE),
 };
 
 struct mvebu_comphy_priv {
@@ -265,6 +279,8 @@ static int mvebu_comphy_get_mode(bool fw_mode, int lane, int port,
 				 enum phy_mode mode, int submode)
 {
 	int i, n = ARRAY_SIZE(mvebu_comphy_cp110_modes);
+	/* Ignore PCIe submode: it represents the width */
+	bool ignore_submode = (mode == PHY_MODE_PCIE);
 	const struct mvebu_comphy_conf *conf;
 
 	/* Unused PHY mux value is 0x0 */
@@ -276,7 +292,7 @@ static int mvebu_comphy_get_mode(bool fw_mode, int lane, int port,
 		if (conf->lane == lane &&
 		    conf->port == port &&
 		    conf->mode == mode &&
-		    conf->submode == submode)
+		    (conf->submode == submode || ignore_submode))
 			break;
 	}
 
@@ -678,6 +694,12 @@ static int mvebu_comphy_power_on(struct phy *phy)
 		dev_dbg(priv->dev, "set lane %d to SATA mode\n", lane->id);
 		fw_param = COMPHY_FW_PARAM(fw_mode, lane->port);
 		break;
+	case PHY_MODE_PCIE:
+		dev_dbg(priv->dev, "set lane %d to PCIe mode (x%d)\n", lane->id,
+			lane->submode);
+		fw_param = COMPHY_FW_PARAM_PCIE(fw_mode, lane->port,
+						lane->submode);
+		break;
 	default:
 		dev_err(priv->dev, "unsupported PHY mode (%d)\n", lane->mode);
 		return -ENOTSUPP;
@@ -714,6 +736,11 @@ static int mvebu_comphy_set_mode(struct phy *phy,
 
 	lane->mode = mode;
 	lane->submode = submode;
+
+	/* PCIe submode represents the width */
+	if (mode == PHY_MODE_PCIE && !lane->submode)
+		lane->submode = 1;
+
 	return 0;
 }
 
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

  parent reply index

Thread overview: 30+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-07-31 12:21 [PATCH v3 00/19] Enhance CP110 COMPHY support Miquel Raynal
2019-07-31 12:21 ` [PATCH v3 01/19] phy: mvebu-cp110-comphy: Add clocks support Miquel Raynal
2019-07-31 12:21 ` [PATCH v3 02/19] phy: mvebu-cp110-comphy: Explicitly initialize the lane submode Miquel Raynal
2019-07-31 12:21 ` [PATCH v3 03/19] phy: mvebu-cp110-comphy: Add SMC call support Miquel Raynal
2019-07-31 12:21 ` [PATCH v3 04/19] phy: mvebu-cp110-comphy: List already supported Ethernet modes Miquel Raynal
2019-07-31 12:21 ` [PATCH v3 05/19] phy: mvebu-cp110-comphy: Add RXAUI support Miquel Raynal
2019-07-31 12:21 ` [PATCH v3 06/19] phy: mvebu-cp110-comphy: Rename the macro handling only Ethernet modes Miquel Raynal
2019-07-31 12:21 ` [PATCH v3 07/19] phy: mvebu-cp110-comphy: Allow non-Ethernet modes to be configured Miquel Raynal
2019-07-31 12:21 ` [PATCH v3 08/19] phy: mvebu-cp110-comphy: Add USB3 host/device support Miquel Raynal
2019-07-31 12:21 ` [PATCH v3 09/19] phy: mvebu-cp110-comphy: Add SATA support Miquel Raynal
2019-07-31 12:21 ` [PATCH v3 10/19] phy: mvebu-cp110-comphy: Cosmetic change in a helper Miquel Raynal
2019-07-31 12:21 ` Miquel Raynal [this message]
2019-07-31 12:21 ` [PATCH v3 12/19] phy: mvebu-cp110-comphy: Update comment about powering off all lanes at boot Miquel Raynal
2019-07-31 12:21 ` [PATCH v3 13/19] dt-bindings: phy: Add Marvell COMPHY clocks Miquel Raynal
2019-08-12 21:29   ` Rob Herring
2019-08-19  8:40     ` Miquel Raynal
2019-07-31 12:21 ` [PATCH v3 14/19] dt-bindings: pci: add PHY properties to Armada 7K/8K controller bindings Miquel Raynal
2019-08-21 18:28   ` Rob Herring
2019-08-24 10:15     ` Miquel Raynal
2019-07-31 12:21 ` [PATCH v3 15/19] arm64: dts: marvell: Add CP110 COMPHY clocks Miquel Raynal
2019-07-31 12:21 ` [PATCH v3 16/19] arm64: dts: marvell: Add 7k/8k per-port PHYs in SATA nodes Miquel Raynal
2019-07-31 12:21 ` [PATCH v3 17/19] arm64: dts: marvell: Add 7k/8k PHYs in USB3 nodes Miquel Raynal
2019-07-31 12:21 ` [PATCH v3 18/19] arm64: dts: marvell: Add 7k/8k PHYs in PCIe nodes Miquel Raynal
2019-07-31 12:21 ` [PATCH v3 19/19] arm64: dts: marvell: Convert 7k/8k usb-phy properties to phy-supply Miquel Raynal
2019-08-23  3:16 ` [PATCH v3 00/19] Enhance CP110 COMPHY support Kishon Vijay Abraham I
2019-08-23  7:33   ` Miquel Raynal
2019-08-24 11:54   ` Miquel Raynal
2019-08-26 11:51     ` Kishon Vijay Abraham I
2019-08-26 12:23       ` Miquel Raynal
2019-08-27 14:22 ` Gregory CLEMENT

Reply instructions:

You may reply publically to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20190731122126.3049-12-miquel.raynal@bootlin.com \
    --to=miquel.raynal@bootlin.com \
    --cc=andrew@lunn.ch \
    --cc=antoine.tenart@bootlin.com \
    --cc=devicetree@vger.kernel.org \
    --cc=gregory.clement@bootlin.com \
    --cc=jason@lakedaemon.net \
    --cc=jaz@semihalf.com \
    --cc=kishon@ti.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux@armlinux.org.uk \
    --cc=maxime.chevallier@bootlin.com \
    --cc=nadavh@marvell.com \
    --cc=robh+dt@kernel.org \
    --cc=sebastian.hesselbarth@gmail.com \
    --cc=thomas.petazzoni@bootlin.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-ARM-Kernel Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-arm-kernel/0 linux-arm-kernel/git/0.git
	git clone --mirror https://lore.kernel.org/linux-arm-kernel/1 linux-arm-kernel/git/1.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-arm-kernel linux-arm-kernel/ https://lore.kernel.org/linux-arm-kernel \
		linux-arm-kernel@lists.infradead.org infradead-linux-arm-kernel@archiver.kernel.org
	public-inbox-index linux-arm-kernel

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.infradead.lists.linux-arm-kernel


AGPL code for this site: git clone https://public-inbox.org/ public-inbox