From: Stefan-gabriel Mirea <stefan-gabriel.mirea@nxp.com>
To: "corbet@lwn.net" <corbet@lwn.net>,
"robh+dt@kernel.org" <robh+dt@kernel.org>,
"mark.rutland@arm.com" <mark.rutland@arm.com>,
"gregkh@linuxfoundation.org" <gregkh@linuxfoundation.org>,
"catalin.marinas@arm.com" <catalin.marinas@arm.com>,
"will@kernel.org" <will@kernel.org>,
"shawnguo@kernel.org" <shawnguo@kernel.org>,
Leo Li <leoyang.li@nxp.com>
Cc: "devicetree@vger.kernel.org" <devicetree@vger.kernel.org>,
"linux-doc@vger.kernel.org" <linux-doc@vger.kernel.org>,
Larisa Ileana Grigore <larisa.grigore@nxp.com>,
"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>,
"linux-serial@vger.kernel.org" <linux-serial@vger.kernel.org>,
"jslaby@suse.com" <jslaby@suse.com>,
Cosmin Stefan Stoica <cosmin.stoica@nxp.com>,
"linux-arm-kernel@lists.infradead.org"
<linux-arm-kernel@lists.infradead.org>
Subject: [PATCH v2 4/6] dt-bindings: serial: Document Freescale LINFlex UART
Date: Fri, 9 Aug 2019 11:29:14 +0000 [thread overview]
Message-ID: <20190809112853.15846-5-stefan-gabriel.mirea@nxp.com> (raw)
In-Reply-To: <20190809112853.15846-1-stefan-gabriel.mirea@nxp.com>
From: Stoica Cosmin-Stefan <cosmin.stoica@nxp.com>
Add documentation for the serial communication interface module (LINFlex),
found in two instances on S32V234.
Signed-off-by: Stoica Cosmin-Stefan <cosmin.stoica@nxp.com>
Signed-off-by: Larisa Grigore <Larisa.Grigore@nxp.com>
Signed-off-by: Stefan-Gabriel Mirea <stefan-gabriel.mirea@nxp.com>
---
.../bindings/serial/fsl,s32-linflexuart.txt | 24 +++++++++++++++++++
1 file changed, 24 insertions(+)
create mode 100644 Documentation/devicetree/bindings/serial/fsl,s32-linflexuart.txt
diff --git a/Documentation/devicetree/bindings/serial/fsl,s32-linflexuart.txt b/Documentation/devicetree/bindings/serial/fsl,s32-linflexuart.txt
new file mode 100644
index 000000000000..957ffeaca9f1
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/fsl,s32-linflexuart.txt
@@ -0,0 +1,24 @@
+* Freescale Linflex UART
+
+The LINFlexD controller implements several LIN protocol versions, as well as
+support for full-duplex UART communication through 8-bit and 9-bit frames. The
+Linflex UART driver enables operation only in UART mode.
+
+See chapter 47 ("LINFlexD") in the reference manual[1].
+
+Required properties:
+- compatible :
+ - "fsl,s32-linflexuart" for linflex configured in uart mode which
+ is compatible with the one integrated on S32V234 SoC
+- reg : Address and length of the register set for the device
+- interrupts : Should contain uart interrupt
+
+Example:
+uart0:serial@40053000 {
+ compatible = "fsl,s32-linflexuart";
+ reg = <0x0 0x40053000 0x0 0x1000>;
+ interrupts = <0 59 4>;
+ status = "disabled";
+};
+
+[1] https://www.nxp.com/webapp/Download?colCode=S32V234RM
--
2.22.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2019-08-09 11:30 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-08-09 11:29 [PATCH v2 0/6] Add initial support for S32V234-EVB Stefan-gabriel Mirea
2019-08-09 11:29 ` [PATCH v2 1/6] dt-bindings: arm: fsl: Add the S32V234-EVB board Stefan-gabriel Mirea
2019-08-12 18:58 ` Rob Herring
2019-08-09 11:29 ` [PATCH v2 2/6] arm64: Introduce config for S32 Stefan-gabriel Mirea
2019-08-19 8:14 ` Shawn Guo
2019-08-20 16:38 ` Stefan-gabriel Mirea
2019-08-09 11:29 ` [PATCH v2 3/6] arm64: dts: fsl: Add device tree for S32V234-EVB Stefan-gabriel Mirea
2019-08-19 8:58 ` Shawn Guo
2019-08-20 16:38 ` Stefan-gabriel Mirea
2019-08-09 11:29 ` Stefan-gabriel Mirea [this message]
2019-08-21 21:18 ` [PATCH v2 4/6] dt-bindings: serial: Document Freescale LINFlex UART Rob Herring
2019-08-22 17:41 ` Stefan-gabriel Mirea
2019-08-09 11:29 ` [PATCH v2 5/6] tty: serial: Add linflexuart driver for S32V234 Stefan-gabriel Mirea
2019-08-09 11:29 ` [PATCH v2 6/6] arm64: defconfig: Enable configs " Stefan-gabriel Mirea
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190809112853.15846-5-stefan-gabriel.mirea@nxp.com \
--to=stefan-gabriel.mirea@nxp.com \
--cc=catalin.marinas@arm.com \
--cc=corbet@lwn.net \
--cc=cosmin.stoica@nxp.com \
--cc=devicetree@vger.kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=jslaby@suse.com \
--cc=larisa.grigore@nxp.com \
--cc=leoyang.li@nxp.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-doc@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-serial@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
--cc=shawnguo@kernel.org \
--cc=will@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).