From: "Uwe Kleine-König" <uwe@kleine-koenig.org> To: Nicolas Ferre <nicolas.ferre@microchip.com>, Alexandre Belloni <alexandre.belloni@bootlin.com>, Ludovic Desroches <ludovic.desroches@microchip.com> Cc: linux-arm-kernel@lists.infradead.org Subject: [PATCH 4/9] ARM: dts: at91: cosino: Style cleanup Date: Mon, 12 Aug 2019 23:27:52 +0200 Message-ID: <20190812212757.23432-4-uwe@kleine-koenig.org> (raw) In-Reply-To: <20190812212757.23432-1-uwe@kleine-koenig.org> - newline between properties and sub-nodes - use tags from included dtsi instead of duplicating the hierarchy - status should be the last property There are no differences in the generated .dtb Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org> --- arch/arm/boot/dts/at91-cosino.dtsi | 203 ++++++++++----------- arch/arm/boot/dts/at91-cosino_mega2560.dts | 93 +++++----- 2 files changed, 145 insertions(+), 151 deletions(-) diff --git a/arch/arm/boot/dts/at91-cosino.dtsi b/arch/arm/boot/dts/at91-cosino.dtsi index 47721c9a2e42..feebd54f670e 100644 --- a/arch/arm/boot/dts/at91-cosino.dtsi +++ b/arch/arm/boot/dts/at91-cosino.dtsi @@ -33,122 +33,119 @@ clock-frequency = <12000000>; }; }; +}; - ahb { - apb { - tcb0: timer@f8008000 { - timer@0 { - compatible = "atmel,tcb-timer"; - reg = <0>; - }; +&adc0 { + atmel,adc-ts-wires = <4>; + atmel,adc-ts-pressure-threshold = <10000>; + status = "okay"; +}; + +&dbgu { + status = "okay"; +}; - timer@1 { - compatible = "atmel,tcb-timer"; - reg = <1>; +&ebi { + pinctrl-0 = <&pinctrl_ebi_addr_nand + &pinctrl_ebi_data_0_7>; + pinctrl-names = "default"; + status = "okay"; + + nand-controller { + pinctrl-0 = <&pinctrl_nand_oe_we + &pinctrl_nand_cs + &pinctrl_nand_rb>; + pinctrl-names = "default"; + status = "okay"; + + nand@3 { + reg = <0x3 0x0 0x800000>; + rb-gpios = <&pioD 5 GPIO_ACTIVE_HIGH>; + cs-gpios = <&pioD 4 GPIO_ACTIVE_HIGH>; + nand-bus-width = <8>; + nand-ecc-mode = "hw"; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + nand-on-flash-bbt; + label = "atmel_nand"; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + at91bootstrap@0 { + label = "at91bootstrap"; + reg = <0x0 0x40000>; }; - }; - mmc0: mmc@f0008000 { - pinctrl-0 = < - &pinctrl_board_mmc0 - &pinctrl_mmc0_slot0_clk_cmd_dat0 - &pinctrl_mmc0_slot0_dat1_3>; - status = "okay"; - slot@0 { - reg = <0>; - bus-width = <4>; - cd-gpios = <&pioD 15 GPIO_ACTIVE_HIGH>; + uboot@40000 { + label = "u-boot"; + reg = <0x40000 0x80000>; }; - }; - dbgu: serial@fffff200 { - status = "okay"; - }; + ubootenv@c0000 { + label = "U-Boot Env"; + reg = <0xc0000 0x140000>; + }; - usart0: serial@f801c000 { - status = "okay"; - }; + kernel@200000 { + label = "kernel"; + reg = <0x200000 0x600000>; + }; - i2c0: i2c@f8010000 { - status = "okay"; + rootfs@800000 { + label = "rootfs"; + reg = <0x800000 0x0f800000>; + }; }; + }; + }; +}; - adc0: adc@f804c000 { - atmel,adc-ts-wires = <4>; - atmel,adc-ts-pressure-threshold = <10000>; - status = "okay"; - }; +&i2c0 { + status = "okay"; +}; - pinctrl@fffff400 { - mmc0 { - pinctrl_board_mmc0: mmc0-board { - atmel,pins = - <AT91_PIOD 15 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD15 gpio CD pin pull up and deglitch */ - }; - }; - }; +&mmc0 { + pinctrl-0 = < + &pinctrl_board_mmc0 + &pinctrl_mmc0_slot0_clk_cmd_dat0 + &pinctrl_mmc0_slot0_dat1_3>; + status = "okay"; + + slot@0 { + reg = <0>; + bus-width = <4>; + cd-gpios = <&pioD 15 GPIO_ACTIVE_HIGH>; + }; +}; - watchdog@fffffe40 { - status = "okay"; - }; +&pinctrl { + mmc0 { + pinctrl_board_mmc0: mmc0-board { + atmel,pins = + <AT91_PIOD 15 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD15 gpio CD pin pull up and deglitch */ }; + }; +}; - ebi: ebi@10000000 { - pinctrl-0 = <&pinctrl_ebi_addr_nand - &pinctrl_ebi_data_0_7>; - pinctrl-names = "default"; - status = "okay"; - - nand_controller: nand-controller { - status = "okay"; - pinctrl-0 = <&pinctrl_nand_oe_we - &pinctrl_nand_cs - &pinctrl_nand_rb>; - pinctrl-names = "default"; - - nand@3 { - reg = <0x3 0x0 0x800000>; - rb-gpios = <&pioD 5 GPIO_ACTIVE_HIGH>; - cs-gpios = <&pioD 4 GPIO_ACTIVE_HIGH>; - nand-bus-width = <8>; - nand-ecc-mode = "hw"; - nand-ecc-strength = <4>; - nand-ecc-step-size = <512>; - nand-on-flash-bbt; - label = "atmel_nand"; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - at91bootstrap@0 { - label = "at91bootstrap"; - reg = <0x0 0x40000>; - }; - - uboot@40000 { - label = "u-boot"; - reg = <0x40000 0x80000>; - }; - - ubootenv@c0000 { - label = "U-Boot Env"; - reg = <0xc0000 0x140000>; - }; - - kernel@200000 { - label = "kernel"; - reg = <0x200000 0x600000>; - }; - - rootfs@800000 { - label = "rootfs"; - reg = <0x800000 0x0f800000>; - }; - }; - }; - }; - }; +&tcb0 { + timer@0 { + compatible = "atmel,tcb-timer"; + reg = <0>; + }; + + timer@1 { + compatible = "atmel,tcb-timer"; + reg = <1>; }; }; + +&usart0 { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/at91-cosino_mega2560.dts b/arch/arm/boot/dts/at91-cosino_mega2560.dts index 8fde06adf7cb..73e88d1ba4ed 100644 --- a/arch/arm/boot/dts/at91-cosino_mega2560.dts +++ b/arch/arm/boot/dts/at91-cosino_mega2560.dts @@ -17,61 +17,58 @@ / { model = "HCE Cosino Mega 2560"; compatible = "hce,cosino_mega2560", "atmel,at91sam9x5", "atmel,at91sam9"; +}; + +&adc0 { + atmel,adc-ts-wires = <4>; + atmel,adc-ts-pressure-threshold = <10000>; + status = "okay"; +}; - ahb { - apb { - macb0: ethernet@f802c000 { - phy-mode = "rmii"; - status = "okay"; - }; +&macb0 { + phy-mode = "rmii"; + status = "okay"; +}; - adc0: adc@f804c000 { - atmel,adc-ts-wires = <4>; - atmel,adc-ts-pressure-threshold = <10000>; - status = "okay"; - }; +&mmc1 { + pinctrl-0 = < + &pinctrl_mmc1_slot0_clk_cmd_dat0 + &pinctrl_mmc1_slot0_dat1_3>; + status = "okay"; - rtc@fffffeb0 { - status = "okay"; - }; + slot@0 { + reg = <0>; + bus-width = <4>; + non-removable; + }; +}; - usart1: serial@f8020000 { - status = "okay"; - }; +&rtc { + status = "okay"; +}; - usart2: serial@f8024000 { - status = "okay"; - }; +&usart1 { + status = "okay"; +}; - usb2: gadget@f803c000 { - atmel,vbus-gpio = <&pioB 16 GPIO_ACTIVE_HIGH>; - status = "okay"; - }; +&usart2 { + status = "okay"; +}; - mmc1: mmc@f000c000 { - pinctrl-0 = < - &pinctrl_mmc1_slot0_clk_cmd_dat0 - &pinctrl_mmc1_slot0_dat1_3>; - status = "okay"; - slot@0 { - reg = <0>; - bus-width = <4>; - non-removable; - }; - }; - }; +&usb0 { + num-ports = <3>; + atmel,vbus-gpio = <0 /* &pioD 18 GPIO_ACTIVE_LOW */ + &pioD 19 GPIO_ACTIVE_LOW + &pioD 20 GPIO_ACTIVE_LOW + >; + status = "okay"; +}; - usb0: ohci@600000 { - status = "okay"; - num-ports = <3>; - atmel,vbus-gpio = <0 /* &pioD 18 GPIO_ACTIVE_LOW */ - &pioD 19 GPIO_ACTIVE_LOW - &pioD 20 GPIO_ACTIVE_LOW - >; - }; +&usb1 { + status = "okay"; +}; - usb1: ehci@700000 { - status = "okay"; - }; - }; +&usb2 { + atmel,vbus-gpio = <&pioB 16 GPIO_ACTIVE_HIGH>; + status = "okay"; }; -- 2.20.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply index Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top 2019-08-12 21:27 [PATCH 1/9] ARM: dts: at91: Add label for sam9x5's internal RTC Uwe Kleine-König 2019-08-12 21:27 ` [PATCH 2/9] ARM: dts: at91: ariag25: Style cleanup Uwe Kleine-König 2019-08-21 16:43 ` Alexandre Belloni 2019-08-12 21:27 ` [PATCH 3/9] ARM: dts: at91: ariettag25: style cleanup Uwe Kleine-König 2019-08-21 16:44 ` Alexandre Belloni 2019-08-12 21:27 ` Uwe Kleine-König [this message] 2019-08-21 16:44 ` [PATCH 4/9] ARM: dts: at91: cosino: Style cleanup Alexandre Belloni 2019-08-12 21:27 ` [PATCH 5/9] ARM: dts: at91: kizboxmini: " Uwe Kleine-König 2019-08-21 16:45 ` Alexandre Belloni 2019-08-12 21:27 ` [PATCH 6/9] ARM: dts: at91: at91sam9g15: " Uwe Kleine-König 2019-08-21 16:46 ` Alexandre Belloni 2019-08-12 21:27 ` [PATCH 7/9] ARM: dts: at91: at91sam9xx5ek: " Uwe Kleine-König 2019-08-21 16:46 ` Alexandre Belloni 2019-08-12 21:27 ` [PATCH 8/9] ARM: dts: at91: at91sam9x5_lcd.dtsi: " Uwe Kleine-König 2019-08-21 16:47 ` Alexandre Belloni 2019-08-12 21:27 ` [PATCH 9/9] ARM: dts: at91: at91sam9x5dm.dtsi: " Uwe Kleine-König 2019-08-21 16:48 ` Alexandre Belloni 2019-08-21 16:43 ` [PATCH 1/9] ARM: dts: at91: Add label for sam9x5's internal RTC Alexandre Belloni
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20190812212757.23432-4-uwe@kleine-koenig.org \ --to=uwe@kleine-koenig.org \ --cc=alexandre.belloni@bootlin.com \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=ludovic.desroches@microchip.com \ --cc=nicolas.ferre@microchip.com \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: link
Linux-ARM-Kernel Archive on lore.kernel.org Archives are clonable: git clone --mirror https://lore.kernel.org/linux-arm-kernel/0 linux-arm-kernel/git/0.git git clone --mirror https://lore.kernel.org/linux-arm-kernel/1 linux-arm-kernel/git/1.git # If you have public-inbox 1.1+ installed, you may # initialize and index your mirror using the following commands: public-inbox-init -V2 linux-arm-kernel linux-arm-kernel/ https://lore.kernel.org/linux-arm-kernel \ linux-arm-kernel@lists.infradead.org public-inbox-index linux-arm-kernel Example config snippet for mirrors Newsgroup available over NNTP: nntp://nntp.lore.kernel.org/org.infradead.lists.linux-arm-kernel AGPL code for this site: git clone https://public-inbox.org/public-inbox.git