Linux-ARM-Kernel Archive on lore.kernel.org
 help / color / Atom feed
From: Corentin Labbe <clabbe.montjoie@gmail.com>
To: Maxime Ripard <mripard@kernel.org>
Cc: mark.rutland@arm.com, devicetree@vger.kernel.org,
	linux-sunxi@googlegroups.com, linux-kernel@vger.kernel.org,
	wens@csie.org, robh+dt@kernel.org,
	linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH] ARM64: dts: allwinner: Add devicetree for pine H64 modelA evaluation board
Date: Fri, 16 Aug 2019 11:35:13 +0200
Message-ID: <20190816093513.GA25042@Red> (raw)
In-Reply-To: <20190814133322.dawzv3ityakxtqs4@flea>

On Wed, Aug 14, 2019 at 03:33:22PM +0200, Maxime Ripard wrote:
> On Wed, Aug 14, 2019 at 03:17:41PM +0200, Corentin Labbe wrote:
> > On Mon, Aug 12, 2019 at 11:40:00AM +0200, Maxime Ripard wrote:
> > > On Thu, Aug 08, 2019 at 10:42:53AM +0200, Corentin Labbe wrote:
> > > > This patch adds the evaluation variant of the model A of the PineH64.
> > > > The model A has the same size of the pine64 and has a PCIE slot.
> > > >
> > > > The only devicetree difference with current pineH64, is the PHY
> > > > regulator.
> > > >
> > > > Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
> > > > ---
> > > >  arch/arm64/boot/dts/allwinner/Makefile        |  1 +
> > > >  .../sun50i-h6-pine-h64-modelA-eval.dts        | 26 +++++++++++++++++++
> > > >  2 files changed, 27 insertions(+)
> > > >  create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64-modelA-eval.dts
> > > >
> > > > diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
> > > > index f6db0611cb85..9a02166cbf72 100644
> > > > --- a/arch/arm64/boot/dts/allwinner/Makefile
> > > > +++ b/arch/arm64/boot/dts/allwinner/Makefile
> > > > @@ -25,3 +25,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-3.dtb
> > > >  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-lite2.dtb
> > > >  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb
> > > >  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
> > > > +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-modelA-eval.dtb
> > > > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64-modelA-eval.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64-modelA-eval.dts
> > > > new file mode 100644
> > > > index 000000000000..d8ff02747efe
> > > > --- /dev/null
> > > > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64-modelA-eval.dts
> > > > @@ -0,0 +1,26 @@
> > > > +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
> > > > +/*
> > > > + * Copyright (C) 2019 Corentin Labbe <clabbe.montjoie@gmail.com>
> > > > + */
> > > > +
> > > > +#include "sun50i-h6-pine-h64.dts"
> > > > +
> > > > +/ {
> > > > +	model = "Pine H64 model A evaluation board";
> > > > +	compatible = "pine64,pine-h64-modelA-eval", "allwinner,sun50i-h6";
> > > > +
> > > > +	reg_gmac_3v3: gmac-3v3 {
> > > > +		compatible = "regulator-fixed";
> > > > +		regulator-name = "vcc-gmac-3v3";
> > > > +		regulator-min-microvolt = <3300000>;
> > > > +		regulator-max-microvolt = <3300000>;
> > > > +		startup-delay-us = <100000>;
> > > > +		gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>;
> > > > +		enable-active-high;
> > > > +	};
> > > > +
> > > > +};
> > > > +
> > > > +&emac {
> > > > +	phy-supply = <&reg_gmac_3v3>;
> > > > +};
> > >
> > > I might be missing some context here, but I'm pretty sure that the
> > > initial intent of the pine h64 DTS was to support the model A all
> > > along.
> > >
> >
> > The regulator changed between modelA and B.
> > See this old patchset (supporting modelA) https://patchwork.kernel.org/patch/10539149/ for example.
> 
> I'm not sure what your point is, but mine is that everything about the
> model A should be in sun50i-h6-pine-h64.dts.
> 

model A and B are different enough for distinct dtb, (see sub-thread on HDMI difference for an other difference than PHY regulator)
And clearly, the current dtb is for model B.

So do you mean that we need to create a new dtb for model B ? (and hack the current back to model A ?)

Regards

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

  reply index

Thread overview: 15+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-08-08  8:42 Corentin Labbe
2019-08-08 14:50 ` [linux-sunxi] " Clément Péron
2019-08-14 13:07   ` Corentin Labbe
2019-08-12  9:40 ` Maxime Ripard
2019-08-14 13:17   ` Corentin Labbe
2019-08-14 13:33     ` Maxime Ripard
2019-08-16  9:35       ` Corentin Labbe [this message]
2019-08-16 11:36         ` Maxime Ripard
2019-08-16 11:57           ` Corentin Labbe
2019-08-16 13:52             ` Maxime Ripard
2019-08-16 14:00               ` Corentin Labbe
2019-08-12 10:56 ` [linux-sunxi] " Jernej Škrabec
2019-08-14 13:20   ` Corentin Labbe
2019-08-14 13:28     ` Clément Péron
2019-08-16  9:50       ` Jernej Škrabec

Reply instructions:

You may reply publically to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20190816093513.GA25042@Red \
    --to=clabbe.montjoie@gmail.com \
    --cc=devicetree@vger.kernel.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-sunxi@googlegroups.com \
    --cc=mark.rutland@arm.com \
    --cc=mripard@kernel.org \
    --cc=robh+dt@kernel.org \
    --cc=wens@csie.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-ARM-Kernel Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-arm-kernel/0 linux-arm-kernel/git/0.git
	git clone --mirror https://lore.kernel.org/linux-arm-kernel/1 linux-arm-kernel/git/1.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-arm-kernel linux-arm-kernel/ https://lore.kernel.org/linux-arm-kernel \
		linux-arm-kernel@lists.infradead.org infradead-linux-arm-kernel@archiver.kernel.org
	public-inbox-index linux-arm-kernel


Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.infradead.lists.linux-arm-kernel


AGPL code for this site: git clone https://public-inbox.org/ public-inbox