Linux-ARM-Kernel Archive on lore.kernel.org
 help / color / Atom feed
* [PATCH 00/20] Add new Marvell CN9130 SoC support
@ 2019-08-06 14:54 Miquel Raynal
  2019-08-06 14:54 ` [PATCH 01/20] arm64: dts: marvell: Enumerate the first AP806 syscon Miquel Raynal
                   ` (19 more replies)
  0 siblings, 20 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-08-06 14:54 UTC (permalink / raw)
  To: Rob Herring, Mark Rutland
  Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
	Gregory Clement, Maxime Chevallier, Nadav Haklai,
	Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
	linux-arm-kernel

Hello,

This is the third and last batch of changes to support new
Marvell CN9130 SoCs. The CN9130 is made of one AP807 and one internal
CP115. There are three development boards that are made of this SoC:
* CN9130-DB
* CN9131-DB (with one additional modular CP115 compared to CN9130-DB)
* CN9132-DB (with two additional modular CP115 compared to CN9130-DB)

This series applies on top of the AP806 and AP807 clock series (see
below) and will work only if applied on top of:
* CP110 COMPHY:
https://patchwork.kernel.org/cover/11067647/
* AP806 CPU clocks:
https://patchwork.kernel.org/cover/11038577/
* AP807 clocks:
https://patchwork.kernel.org/cover/11076435/
* CP115 pinctrl:
http://patchwork.ozlabs.org/cover/1142107/

As CP110 and CP115 (alternatively, AP806 and AP807) are very similar,
we first reorganize DT files to create CP11x (and AP80x) generic
files, before including them from the new specific CP110/CP115
(AP806/AP807) ones.

A few small improvements/fixes in these files are also carried.

Thanks,
Miquèl


Ben Peled (1):
  dt-bindings: ap80x: replace AP806 with AP80x

Grzegorz Jaszczyk (7):
  arm64: dts: marvell: Add AP806-dual cache description
  arm64: dts: marvell: Add AP806-quad cache description
  arm64: dts: marvell: Add AP807-quad cache description
  dt-bindings: marvell: Declare the CN913x SoC compatibles
  arm64: dts: marvell: Add support for Marvell CN9130-DB
  arm64: dts: marvell: Add support for Marvell CN9131-DB
  arm64: dts: marvell: Add support for Marvell CN9132-DB

Konstantin Porotchkin (1):
  arm64: dts: marvell: Prepare the introduction of AP807 based SoCs

Miquel Raynal (11):
  arm64: dts: marvell: Enumerate the first AP806 syscon
  arm64: dts: marvell: Add AP806-dual missing CPU clocks
  MAINTAINERS: Add new Marvell CN9130-based files to track
  arm64: dts: marvell: Move clocks to AP806 specific file
  arm64: dts: marvell: Add support for AP807/AP807-quad
  arm64: dts: marvell: Fix CP110 NAND controller node multi-line comment
    alignment
  arm64: dts: marvell: Prepare the introduction of CP115
  arm64: dts: marvell: Drop PCIe I/O ranges from CP11x file
  arm64: dts: marvell: Externalize PCIe macros from CP11x file
  arm64: dts: marvell: Add support for CP115
  arm64: dts: marvell: Add support for Marvell CN9130 SoC support

 ...roller.txt => ap80x-system-controller.txt} |  14 +-
 .../bindings/arm/marvell/armada-7k-8k.txt     |  13 +-
 MAINTAINERS                                   |   3 +-
 arch/arm64/boot/dts/marvell/Makefile          |   3 +
 arch/arm64/boot/dts/marvell/armada-70x0.dtsi  |  28 +-
 .../boot/dts/marvell/armada-8040-mcbin.dtsi   |   3 +-
 arch/arm64/boot/dts/marvell/armada-80x0.dtsi  |  56 +-
 .../boot/dts/marvell/armada-ap806-dual.dtsi   |  23 +
 .../boot/dts/marvell/armada-ap806-quad.dtsi   |  42 ++
 arch/arm64/boot/dts/marvell/armada-ap806.dtsi | 456 +-------------
 .../boot/dts/marvell/armada-ap807-quad.dtsi   |  93 +++
 arch/arm64/boot/dts/marvell/armada-ap807.dtsi |  29 +
 arch/arm64/boot/dts/marvell/armada-ap80x.dtsi | 444 ++++++++++++++
 .../arm64/boot/dts/marvell/armada-common.dtsi |   4 +-
 arch/arm64/boot/dts/marvell/armada-cp110.dtsi | 575 +-----------------
 arch/arm64/boot/dts/marvell/armada-cp115.dtsi |  12 +
 arch/arm64/boot/dts/marvell/armada-cp11x.dtsi | 568 +++++++++++++++++
 arch/arm64/boot/dts/marvell/cn9130-db.dts     | 403 ++++++++++++
 arch/arm64/boot/dts/marvell/cn9130.dtsi       |  37 ++
 arch/arm64/boot/dts/marvell/cn9131-db.dts     | 202 ++++++
 arch/arm64/boot/dts/marvell/cn9132-db.dts     | 221 +++++++
 21 files changed, 2161 insertions(+), 1068 deletions(-)
 rename Documentation/devicetree/bindings/arm/marvell/{ap806-system-controller.txt => ap80x-system-controller.txt} (91%)
 create mode 100644 arch/arm64/boot/dts/marvell/armada-ap807-quad.dtsi
 create mode 100644 arch/arm64/boot/dts/marvell/armada-ap807.dtsi
 create mode 100644 arch/arm64/boot/dts/marvell/armada-ap80x.dtsi
 create mode 100644 arch/arm64/boot/dts/marvell/armada-cp115.dtsi
 create mode 100644 arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
 create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db.dts
 create mode 100644 arch/arm64/boot/dts/marvell/cn9130.dtsi
 create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db.dts
 create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db.dts

-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 25+ messages in thread

* [PATCH 01/20] arm64: dts: marvell: Enumerate the first AP806 syscon
  2019-08-06 14:54 [PATCH 00/20] Add new Marvell CN9130 SoC support Miquel Raynal
@ 2019-08-06 14:54 ` Miquel Raynal
  2019-08-06 14:54 ` [PATCH 02/20] arm64: dts: marvell: Add AP806-dual missing CPU clocks Miquel Raynal
                   ` (18 subsequent siblings)
  19 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-08-06 14:54 UTC (permalink / raw)
  To: Rob Herring, Mark Rutland
  Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
	Gregory Clement, Maxime Chevallier, Nadav Haklai,
	Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
	linux-arm-kernel

There are two system controllers in the AP80x, like for ap_syscon1,
enumerate the first one by renaming it s/ap_syscon/ap_syscon0/.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 arch/arm64/boot/dts/marvell/armada-ap806.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/marvell/armada-ap806.dtsi b/arch/arm64/boot/dts/marvell/armada-ap806.dtsi
index d06dd198f2c7..a23ddd46efc5 100644
--- a/arch/arm64/boot/dts/marvell/armada-ap806.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-ap806.dtsi
@@ -246,7 +246,7 @@
 				status = "disabled";
 			};
 
-			ap_syscon: system-controller@6f4000 {
+			ap_syscon0: system-controller@6f4000 {
 				compatible = "syscon", "simple-mfd";
 				reg = <0x6f4000 0x2000>;
 
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 25+ messages in thread

* [PATCH 02/20] arm64: dts: marvell: Add AP806-dual missing CPU clocks
  2019-08-06 14:54 [PATCH 00/20] Add new Marvell CN9130 SoC support Miquel Raynal
  2019-08-06 14:54 ` [PATCH 01/20] arm64: dts: marvell: Enumerate the first AP806 syscon Miquel Raynal
@ 2019-08-06 14:54 ` Miquel Raynal
  2019-08-06 14:54 ` [PATCH 03/20] dt-bindings: ap80x: replace AP806 with AP80x Miquel Raynal
                   ` (17 subsequent siblings)
  19 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-08-06 14:54 UTC (permalink / raw)
  To: Rob Herring, Mark Rutland
  Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
	Gregory Clement, Maxime Chevallier, Nadav Haklai,
	Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
	linux-arm-kernel

CPU clocks have been added to AP806-quad but not to the -dual
variant.

Fixes: e043bbd61e01 ("arm64: dts: marvell: Add cpu clock node on Armada 7K/8K")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 arch/arm64/boot/dts/marvell/armada-ap806-dual.dtsi | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm64/boot/dts/marvell/armada-ap806-dual.dtsi b/arch/arm64/boot/dts/marvell/armada-ap806-dual.dtsi
index 9024a2d9db07..62ae016ee6aa 100644
--- a/arch/arm64/boot/dts/marvell/armada-ap806-dual.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-ap806-dual.dtsi
@@ -21,6 +21,7 @@
 			reg = <0x000>;
 			enable-method = "psci";
 			#cooling-cells = <2>;
+			clocks = <&cpu_clk 0>;
 		};
 		cpu1: cpu@1 {
 			device_type = "cpu";
@@ -28,6 +29,7 @@
 			reg = <0x001>;
 			enable-method = "psci";
 			#cooling-cells = <2>;
+			clocks = <&cpu_clk 0>;
 		};
 	};
 };
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 25+ messages in thread

* [PATCH 03/20] dt-bindings: ap80x: replace AP806 with AP80x
  2019-08-06 14:54 [PATCH 00/20] Add new Marvell CN9130 SoC support Miquel Raynal
  2019-08-06 14:54 ` [PATCH 01/20] arm64: dts: marvell: Enumerate the first AP806 syscon Miquel Raynal
  2019-08-06 14:54 ` [PATCH 02/20] arm64: dts: marvell: Add AP806-dual missing CPU clocks Miquel Raynal
@ 2019-08-06 14:54 ` Miquel Raynal
  2019-08-21 19:32   ` Rob Herring
  2019-08-06 14:54 ` [PATCH 04/20] MAINTAINERS: Add new Marvell CN9130-based files to track Miquel Raynal
                   ` (16 subsequent siblings)
  19 siblings, 1 reply; 25+ messages in thread
From: Miquel Raynal @ 2019-08-06 14:54 UTC (permalink / raw)
  To: Rob Herring, Mark Rutland
  Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
	Gregory Clement, Maxime Chevallier, Nadav Haklai,
	Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
	Ben Peled, linux-arm-kernel

From: Ben Peled <bpeled@marvell.com>

Rename the text file and update "AP806" into "AP806/AP807" where
relevant.

Signed-off-by: Ben Peled <bpeled@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 ...-controller.txt => ap80x-system-controller.txt} | 14 +++++++-------
 1 file changed, 7 insertions(+), 7 deletions(-)
 rename Documentation/devicetree/bindings/arm/marvell/{ap806-system-controller.txt => ap80x-system-controller.txt} (91%)

diff --git a/Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt b/Documentation/devicetree/bindings/arm/marvell/ap80x-system-controller.txt
similarity index 91%
rename from Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt
rename to Documentation/devicetree/bindings/arm/marvell/ap80x-system-controller.txt
index 26410fbb85be..098d932fc963 100644
--- a/Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt
+++ b/Documentation/devicetree/bindings/arm/marvell/ap80x-system-controller.txt
@@ -1,15 +1,15 @@
-Marvell Armada AP806 System Controller
+Marvell Armada AP80x System Controller
 ======================================
 
-The AP806 is one of the two core HW blocks of the Marvell Armada 7K/8K
-SoCs. It contains system controllers, which provide several registers
-giving access to numerous features: clocks, pin-muxing and many other
-SoC configuration items. This DT binding allows to describe these
-system controllers.
+The AP806/AP807 is one of the two core HW blocks of the Marvell Armada
+7K/8K/931x SoCs. It contains system controllers, which provide several
+registers giving access to numerous features: clocks, pin-muxing and
+many other SoC configuration items. This DT binding allows to describe
+these system controllers.
 
 For the top level node:
  - compatible: must be: "syscon", "simple-mfd";
- - reg: register area of the AP806 system controller
+ - reg: register area of the AP80x system controller
 
 SYSTEM CONTROLLER 0
 ===================
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 25+ messages in thread

* [PATCH 04/20] MAINTAINERS: Add new Marvell CN9130-based files to track
  2019-08-06 14:54 [PATCH 00/20] Add new Marvell CN9130 SoC support Miquel Raynal
                   ` (2 preceding siblings ...)
  2019-08-06 14:54 ` [PATCH 03/20] dt-bindings: ap80x: replace AP806 with AP80x Miquel Raynal
@ 2019-08-06 14:54 ` Miquel Raynal
  2019-08-06 14:54 ` [PATCH 05/20] arm64: dts: marvell: Prepare the introduction of AP807 based SoCs Miquel Raynal
                   ` (15 subsequent siblings)
  19 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-08-06 14:54 UTC (permalink / raw)
  To: Rob Herring, Mark Rutland
  Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
	Gregory Clement, Maxime Chevallier, Nadav Haklai,
	Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
	linux-arm-kernel

Marvell has a new branch of products called CN9130 based on AP807 and
CP115 which are derivatives of the currently supported AP806 and
CP110. Update the MAINTAINERS entry to reflect this change in the
naming.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 MAINTAINERS | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/MAINTAINERS b/MAINTAINERS
index 783569e3c4b4..0d35614fc5e0 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1865,7 +1865,7 @@ F:	arch/arm/boot/dts/dove*
 F:	arch/arm/boot/dts/orion5x*
 T:	git git://git.infradead.org/linux-mvebu.git
 
-ARM/Marvell Kirkwood and Armada 370, 375, 38x, 39x, XP, 3700, 7K/8K SOC support
+ARM/Marvell Kirkwood and Armada 370, 375, 38x, 39x, XP, 3700, 7K/8K, CN9130 SOC support
 M:	Jason Cooper <jason@lakedaemon.net>
 M:	Andrew Lunn <andrew@lunn.ch>
 M:	Gregory Clement <gregory.clement@bootlin.com>
@@ -1877,6 +1877,7 @@ F:	arch/arm/boot/dts/kirkwood*
 F:	arch/arm/configs/mvebu_*_defconfig
 F:	arch/arm/mach-mvebu/
 F:	arch/arm64/boot/dts/marvell/armada*
+F:	arch/arm64/boot/dts/marvell/cn913*
 F:	drivers/cpufreq/armada-37xx-cpufreq.c
 F:	drivers/cpufreq/armada-8k-cpufreq.c
 F:	drivers/cpufreq/mvebu-cpufreq.c
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 25+ messages in thread

* [PATCH 05/20] arm64: dts: marvell: Prepare the introduction of AP807 based SoCs
  2019-08-06 14:54 [PATCH 00/20] Add new Marvell CN9130 SoC support Miquel Raynal
                   ` (3 preceding siblings ...)
  2019-08-06 14:54 ` [PATCH 04/20] MAINTAINERS: Add new Marvell CN9130-based files to track Miquel Raynal
@ 2019-08-06 14:54 ` Miquel Raynal
  2019-08-27 15:20   ` Gregory CLEMENT
  2019-08-06 14:54 ` [PATCH 06/20] arm64: dts: marvell: Move clocks to AP806 specific file Miquel Raynal
                   ` (14 subsequent siblings)
  19 siblings, 1 reply; 25+ messages in thread
From: Miquel Raynal @ 2019-08-06 14:54 UTC (permalink / raw)
  To: Rob Herring, Mark Rutland
  Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
	Gregory Clement, Maxime Chevallier, Nadav Haklai,
	Thomas Petazzoni, Miquel Raynal, Konstantin Porotchkin,
	Stefan Chulski, Marcin Wojtas, linux-arm-kernel

From: Konstantin Porotchkin <kostap@marvell.com>

Prepare the support for Marvell AP807 die. This die is very similar to
AP806 but uses different DDR PHY. AP807 is a major component of CN9130
SoC series.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 arch/arm64/boot/dts/marvell/armada-ap806.dtsi | 448 +----------------
 arch/arm64/boot/dts/marvell/armada-ap80x.dtsi | 456 ++++++++++++++++++
 2 files changed, 458 insertions(+), 446 deletions(-)
 create mode 100644 arch/arm64/boot/dts/marvell/armada-ap80x.dtsi

diff --git a/arch/arm64/boot/dts/marvell/armada-ap806.dtsi b/arch/arm64/boot/dts/marvell/armada-ap806.dtsi
index a23ddd46efc5..cdadb28f287e 100644
--- a/arch/arm64/boot/dts/marvell/armada-ap806.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-ap806.dtsi
@@ -5,454 +5,10 @@
  * Device Tree file for Marvell Armada AP806.
  */
 
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/thermal/thermal.h>
-
-/dts-v1/;
+#define AP_NAME		ap806
+#include "armada-ap80x.dtsi"
 
 / {
 	model = "Marvell Armada AP806";
 	compatible = "marvell,armada-ap806";
-	#address-cells = <2>;
-	#size-cells = <2>;
-
-	aliases {
-		serial0 = &uart0;
-		serial1 = &uart1;
-		gpio0 = &ap_gpio;
-		spi0 = &spi0;
-	};
-
-	psci {
-		compatible = "arm,psci-0.2";
-		method = "smc";
-	};
-
-	reserved-memory {
-		#address-cells = <2>;
-		#size-cells = <2>;
-		ranges;
-
-		/*
-		 * This area matches the mapping done with a
-		 * mainline U-Boot, and should be updated by the
-		 * bootloader.
-		 */
-
-		psci-area@4000000 {
-			reg = <0x0 0x4000000 0x0 0x200000>;
-			no-map;
-		};
-	};
-
-	ap806 {
-		#address-cells = <2>;
-		#size-cells = <2>;
-		compatible = "simple-bus";
-		interrupt-parent = <&gic>;
-		ranges;
-
-		config-space@f0000000 {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			compatible = "simple-bus";
-			ranges = <0x0 0x0 0xf0000000 0x1000000>;
-
-			gic: interrupt-controller@210000 {
-				compatible = "arm,gic-400";
-				#interrupt-cells = <3>;
-				#address-cells = <1>;
-				#size-cells = <1>;
-				ranges;
-				interrupt-controller;
-				interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
-				reg = <0x210000 0x10000>,
-				      <0x220000 0x20000>,
-				      <0x240000 0x20000>,
-				      <0x260000 0x20000>;
-
-				gic_v2m0: v2m@280000 {
-					compatible = "arm,gic-v2m-frame";
-					msi-controller;
-					reg = <0x280000 0x1000>;
-					arm,msi-base-spi = <160>;
-					arm,msi-num-spis = <32>;
-				};
-				gic_v2m1: v2m@290000 {
-					compatible = "arm,gic-v2m-frame";
-					msi-controller;
-					reg = <0x290000 0x1000>;
-					arm,msi-base-spi = <192>;
-					arm,msi-num-spis = <32>;
-				};
-				gic_v2m2: v2m@2a0000 {
-					compatible = "arm,gic-v2m-frame";
-					msi-controller;
-					reg = <0x2a0000 0x1000>;
-					arm,msi-base-spi = <224>;
-					arm,msi-num-spis = <32>;
-				};
-				gic_v2m3: v2m@2b0000 {
-					compatible = "arm,gic-v2m-frame";
-					msi-controller;
-					reg = <0x2b0000 0x1000>;
-					arm,msi-base-spi = <256>;
-					arm,msi-num-spis = <32>;
-				};
-			};
-
-			timer {
-				compatible = "arm,armv8-timer";
-				interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
-					     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
-					     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
-					     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
-			};
-
-			pmu {
-				compatible = "arm,cortex-a72-pmu";
-				interrupt-parent = <&pic>;
-				interrupts = <17>;
-			};
-
-			odmi: odmi@300000 {
-				compatible = "marvell,odmi-controller";
-				interrupt-controller;
-				msi-controller;
-				marvell,odmi-frames = <4>;
-				reg = <0x300000 0x4000>,
-				      <0x304000 0x4000>,
-				      <0x308000 0x4000>,
-				      <0x30C000 0x4000>;
-				marvell,spi-base = <128>, <136>, <144>, <152>;
-			};
-
-			gicp: gicp@3f0040 {
-				compatible = "marvell,ap806-gicp";
-				reg = <0x3f0040 0x10>;
-				marvell,spi-ranges = <64 64>, <288 64>;
-				msi-controller;
-			};
-
-			pic: interrupt-controller@3f0100 {
-				compatible = "marvell,armada-8k-pic";
-				reg = <0x3f0100 0x10>;
-				#interrupt-cells = <1>;
-				interrupt-controller;
-				interrupts = <GIC_PPI 15 IRQ_TYPE_LEVEL_HIGH>;
-			};
-
-			sei: interrupt-controller@3f0200 {
-				compatible = "marvell,ap806-sei";
-				reg = <0x3f0200 0x40>;
-				interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
-				#interrupt-cells = <1>;
-				interrupt-controller;
-				msi-controller;
-			};
-
-			xor@400000 {
-				compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
-				reg = <0x400000 0x1000>,
-				      <0x410000 0x1000>;
-				msi-parent = <&gic_v2m0>;
-				clocks = <&ap_clk 3>;
-				dma-coherent;
-			};
-
-			xor@420000 {
-				compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
-				reg = <0x420000 0x1000>,
-				      <0x430000 0x1000>;
-				msi-parent = <&gic_v2m0>;
-				clocks = <&ap_clk 3>;
-				dma-coherent;
-			};
-
-			xor@440000 {
-				compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
-				reg = <0x440000 0x1000>,
-				      <0x450000 0x1000>;
-				msi-parent = <&gic_v2m0>;
-				clocks = <&ap_clk 3>;
-				dma-coherent;
-			};
-
-			xor@460000 {
-				compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
-				reg = <0x460000 0x1000>,
-				      <0x470000 0x1000>;
-				msi-parent = <&gic_v2m0>;
-				clocks = <&ap_clk 3>;
-				dma-coherent;
-			};
-
-			spi0: spi@510600 {
-				compatible = "marvell,armada-380-spi";
-				reg = <0x510600 0x50>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-				interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&ap_clk 3>;
-				status = "disabled";
-			};
-
-			i2c0: i2c@511000 {
-				compatible = "marvell,mv78230-i2c";
-				reg = <0x511000 0x20>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-				interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
-				timeout-ms = <1000>;
-				clocks = <&ap_clk 3>;
-				status = "disabled";
-			};
-
-			uart0: serial@512000 {
-				compatible = "snps,dw-apb-uart";
-				reg = <0x512000 0x100>;
-				reg-shift = <2>;
-				interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
-				reg-io-width = <1>;
-				clocks = <&ap_clk 3>;
-				status = "disabled";
-			};
-
-			uart1: serial@512100 {
-				compatible = "snps,dw-apb-uart";
-				reg = <0x512100 0x100>;
-				reg-shift = <2>;
-				interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
-				reg-io-width = <1>;
-				clocks = <&ap_clk 3>;
-				status = "disabled";
-
-			};
-
-			watchdog: watchdog@610000 {
-				compatible = "arm,sbsa-gwdt";
-				reg = <0x610000 0x1000>, <0x600000 0x1000>;
-				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
-			};
-
-			ap_sdhci0: sdhci@6e0000 {
-				compatible = "marvell,armada-ap806-sdhci";
-				reg = <0x6e0000 0x300>;
-				interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
-				clock-names = "core";
-				clocks = <&ap_clk 4>;
-				dma-coherent;
-				marvell,xenon-phy-slow-mode;
-				status = "disabled";
-			};
-
-			ap_syscon0: system-controller@6f4000 {
-				compatible = "syscon", "simple-mfd";
-				reg = <0x6f4000 0x2000>;
-
-				ap_clk: clock {
-					compatible = "marvell,ap806-clock";
-					#clock-cells = <1>;
-				};
-
-				ap_pinctrl: pinctrl {
-					compatible = "marvell,ap806-pinctrl";
-
-					uart0_pins: uart0-pins {
-						marvell,pins = "mpp11", "mpp19";
-						marvell,function = "uart0";
-					};
-				};
-
-				ap_gpio: gpio@1040 {
-					compatible = "marvell,armada-8k-gpio";
-					offset = <0x1040>;
-					ngpios = <20>;
-					gpio-controller;
-					#gpio-cells = <2>;
-					gpio-ranges = <&ap_pinctrl 0 0 20>;
-				};
-			};
-
-			ap_syscon1: system-controller@6f8000 {
-				compatible = "syscon", "simple-mfd";
-				reg = <0x6f8000 0x1000>;
-				#address-cells = <1>;
-				#size-cells = <1>;
-
-				cpu_clk: clock-cpu@278 {
-					compatible = "marvell,ap806-cpu-clock";
-					clocks = <&ap_clk 0>, <&ap_clk 1>;
-					#clock-cells = <1>;
-					reg = <0x278 0xa30>;
-				};
-
-				ap_thermal: thermal-sensor@80 {
-					compatible = "marvell,armada-ap806-thermal";
-					reg = <0x80 0x10>;
-					interrupt-parent = <&sei>;
-					interrupts = <18>;
-					#thermal-sensor-cells = <1>;
-				};
-			};
-		};
-	};
-
-	/*
-	 * The thermal IP features one internal sensor plus, if applicable, one
-	 * remote channel wired to one sensor per CPU.
-	 *
-	 * Only one thermal zone per AP/CP may trigger interrupts at a time, the
-	 * first one that will have a critical trip point will be chosen.
-	 */
-	thermal-zones {
-		ap_thermal_ic: ap-thermal-ic {
-			polling-delay-passive = <0>; /* Interrupt driven */
-			polling-delay = <0>; /* Interrupt driven */
-
-			thermal-sensors = <&ap_thermal 0>;
-
-			trips {
-				ap_crit: ap-crit {
-					temperature = <100000>; /* mC degrees */
-					hysteresis = <2000>; /* mC degrees */
-					type = "critical";
-				};
-			};
-
-			cooling-maps { };
-		};
-
-		ap_thermal_cpu0: ap-thermal-cpu0 {
-			polling-delay-passive = <1000>;
-			polling-delay = <1000>;
-
-			thermal-sensors = <&ap_thermal 1>;
-
-			trips {
-				cpu0_hot: cpu0-hot {
-					temperature = <85000>;
-					hysteresis = <2000>;
-					type = "passive";
-				};
-				cpu0_emerg: cpu0-emerg {
-					temperature = <95000>;
-					hysteresis = <2000>;
-					type = "passive";
-				};
-			};
-
-			cooling-maps {
-				map0_hot: map0-hot {
-					trip = <&cpu0_hot>;
-					cooling-device = <&cpu0 1 2>,
-						<&cpu1 1 2>;
-				};
-				map0_emerg: map0-ermerg {
-					trip = <&cpu0_emerg>;
-					cooling-device = <&cpu0 3 3>,
-						<&cpu1 3 3>;
-				};
-			};
-		};
-
-		ap_thermal_cpu1: ap-thermal-cpu1 {
-			polling-delay-passive = <1000>;
-			polling-delay = <1000>;
-
-			thermal-sensors = <&ap_thermal 2>;
-
-			trips {
-				cpu1_hot: cpu1-hot {
-					temperature = <85000>;
-					hysteresis = <2000>;
-					type = "passive";
-				};
-				cpu1_emerg: cpu1-emerg {
-					temperature = <95000>;
-					hysteresis = <2000>;
-					type = "passive";
-				};
-			};
-
-			cooling-maps {
-				map1_hot: map1-hot {
-					trip = <&cpu1_hot>;
-					cooling-device = <&cpu0 1 2>,
-						<&cpu1 1 2>;
-				};
-				map1_emerg: map1-emerg {
-					trip = <&cpu1_emerg>;
-					cooling-device = <&cpu0 3 3>,
-						<&cpu1 3 3>;
-				};
-			};
-		};
-
-		ap_thermal_cpu2: ap-thermal-cpu2 {
-			polling-delay-passive = <1000>;
-			polling-delay = <1000>;
-
-			thermal-sensors = <&ap_thermal 3>;
-
-			trips {
-				cpu2_hot: cpu2-hot {
-					temperature = <85000>;
-					hysteresis = <2000>;
-					type = "passive";
-				};
-				cpu2_emerg: cpu2-emerg {
-					temperature = <95000>;
-					hysteresis = <2000>;
-					type = "passive";
-				};
-			};
-
-			cooling-maps {
-				map2_hot: map2-hot {
-					trip = <&cpu2_hot>;
-					cooling-device = <&cpu2 1 2>,
-						<&cpu3 1 2>;
-				};
-				map2_emerg: map2-emerg {
-					trip = <&cpu2_emerg>;
-					cooling-device = <&cpu2 3 3>,
-						<&cpu3 3 3>;
-				};
-			};
-		};
-
-		ap_thermal_cpu3: ap-thermal-cpu3 {
-			polling-delay-passive = <1000>;
-			polling-delay = <1000>;
-
-			thermal-sensors = <&ap_thermal 4>;
-
-			trips {
-				cpu3_hot: cpu3-hot {
-					temperature = <85000>;
-					hysteresis = <2000>;
-					type = "passive";
-				};
-				cpu3_emerg: cpu3-emerg {
-					temperature = <95000>;
-					hysteresis = <2000>;
-					type = "passive";
-				};
-			};
-
-			cooling-maps {
-				map3_hot: map3-bhot {
-					trip = <&cpu3_hot>;
-					cooling-device = <&cpu2 1 2>,
-						<&cpu3 1 2>;
-				};
-				map3_emerg: map3-emerg {
-					trip = <&cpu3_emerg>;
-					cooling-device = <&cpu2 3 3>,
-						<&cpu3 3 3>;
-				};
-			};
-		};
-	};
 };
diff --git a/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi b/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi
new file mode 100644
index 000000000000..c44cd7c64bf6
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi
@@ -0,0 +1,456 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Marvell Technology Group Ltd.
+ *
+ * Device Tree file for Marvell Armada AP80x.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/dts-v1/;
+
+/ {
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+		gpio0 = &ap_gpio;
+		spi0 = &spi0;
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/*
+		 * This area matches the mapping done with a
+		 * mainline U-Boot, and should be updated by the
+		 * bootloader.
+		 */
+
+		psci-area@4000000 {
+			reg = <0x0 0x4000000 0x0 0x200000>;
+			no-map;
+		};
+	};
+
+	ap806 {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		compatible = "simple-bus";
+		interrupt-parent = <&gic>;
+		ranges;
+
+		config-space@f0000000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "simple-bus";
+			ranges = <0x0 0x0 0xf0000000 0x1000000>;
+
+			gic: interrupt-controller@210000 {
+				compatible = "arm,gic-400";
+				#interrupt-cells = <3>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges;
+				interrupt-controller;
+				interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+				reg = <0x210000 0x10000>,
+				      <0x220000 0x20000>,
+				      <0x240000 0x20000>,
+				      <0x260000 0x20000>;
+
+				gic_v2m0: v2m@280000 {
+					compatible = "arm,gic-v2m-frame";
+					msi-controller;
+					reg = <0x280000 0x1000>;
+					arm,msi-base-spi = <160>;
+					arm,msi-num-spis = <32>;
+				};
+				gic_v2m1: v2m@290000 {
+					compatible = "arm,gic-v2m-frame";
+					msi-controller;
+					reg = <0x290000 0x1000>;
+					arm,msi-base-spi = <192>;
+					arm,msi-num-spis = <32>;
+				};
+				gic_v2m2: v2m@2a0000 {
+					compatible = "arm,gic-v2m-frame";
+					msi-controller;
+					reg = <0x2a0000 0x1000>;
+					arm,msi-base-spi = <224>;
+					arm,msi-num-spis = <32>;
+				};
+				gic_v2m3: v2m@2b0000 {
+					compatible = "arm,gic-v2m-frame";
+					msi-controller;
+					reg = <0x2b0000 0x1000>;
+					arm,msi-base-spi = <256>;
+					arm,msi-num-spis = <32>;
+				};
+			};
+
+			timer {
+				compatible = "arm,armv8-timer";
+				interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+					     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+					     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+					     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+			};
+
+			pmu {
+				compatible = "arm,cortex-a72-pmu";
+				interrupt-parent = <&pic>;
+				interrupts = <17>;
+			};
+
+			odmi: odmi@300000 {
+				compatible = "marvell,odmi-controller";
+				interrupt-controller;
+				msi-controller;
+				marvell,odmi-frames = <4>;
+				reg = <0x300000 0x4000>,
+				      <0x304000 0x4000>,
+				      <0x308000 0x4000>,
+				      <0x30C000 0x4000>;
+				marvell,spi-base = <128>, <136>, <144>, <152>;
+			};
+
+			gicp: gicp@3f0040 {
+				compatible = "marvell,ap806-gicp";
+				reg = <0x3f0040 0x10>;
+				marvell,spi-ranges = <64 64>, <288 64>;
+				msi-controller;
+			};
+
+			pic: interrupt-controller@3f0100 {
+				compatible = "marvell,armada-8k-pic";
+				reg = <0x3f0100 0x10>;
+				#interrupt-cells = <1>;
+				interrupt-controller;
+				interrupts = <GIC_PPI 15 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			sei: interrupt-controller@3f0200 {
+				compatible = "marvell,ap806-sei";
+				reg = <0x3f0200 0x40>;
+				interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+				#interrupt-cells = <1>;
+				interrupt-controller;
+				msi-controller;
+			};
+
+			xor@400000 {
+				compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
+				reg = <0x400000 0x1000>,
+				      <0x410000 0x1000>;
+				msi-parent = <&gic_v2m0>;
+				clocks = <&ap_clk 3>;
+				dma-coherent;
+			};
+
+			xor@420000 {
+				compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
+				reg = <0x420000 0x1000>,
+				      <0x430000 0x1000>;
+				msi-parent = <&gic_v2m0>;
+				clocks = <&ap_clk 3>;
+				dma-coherent;
+			};
+
+			xor@440000 {
+				compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
+				reg = <0x440000 0x1000>,
+				      <0x450000 0x1000>;
+				msi-parent = <&gic_v2m0>;
+				clocks = <&ap_clk 3>;
+				dma-coherent;
+			};
+
+			xor@460000 {
+				compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
+				reg = <0x460000 0x1000>,
+				      <0x470000 0x1000>;
+				msi-parent = <&gic_v2m0>;
+				clocks = <&ap_clk 3>;
+				dma-coherent;
+			};
+
+			spi0: spi@510600 {
+				compatible = "marvell,armada-380-spi";
+				reg = <0x510600 0x50>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&ap_clk 3>;
+				status = "disabled";
+			};
+
+			i2c0: i2c@511000 {
+				compatible = "marvell,mv78230-i2c";
+				reg = <0x511000 0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+				timeout-ms = <1000>;
+				clocks = <&ap_clk 3>;
+				status = "disabled";
+			};
+
+			uart0: serial@512000 {
+				compatible = "snps,dw-apb-uart";
+				reg = <0x512000 0x100>;
+				reg-shift = <2>;
+				interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+				reg-io-width = <1>;
+				clocks = <&ap_clk 3>;
+				status = "disabled";
+			};
+
+			uart1: serial@512100 {
+				compatible = "snps,dw-apb-uart";
+				reg = <0x512100 0x100>;
+				reg-shift = <2>;
+				interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+				reg-io-width = <1>;
+				clocks = <&ap_clk 3>;
+				status = "disabled";
+
+			};
+
+			watchdog: watchdog@610000 {
+				compatible = "arm,sbsa-gwdt";
+				reg = <0x610000 0x1000>, <0x600000 0x1000>;
+				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			ap_sdhci0: sdhci@6e0000 {
+				compatible = "marvell,armada-ap806-sdhci";
+				reg = <0x6e0000 0x300>;
+				interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+				clock-names = "core";
+				clocks = <&ap_clk 4>;
+				dma-coherent;
+				marvell,xenon-phy-slow-mode;
+				status = "disabled";
+			};
+
+			ap_syscon0: system-controller@6f4000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x6f4000 0x2000>;
+
+				ap_clk: clock {
+					compatible = "marvell,ap806-clock";
+					#clock-cells = <1>;
+				};
+
+				ap_pinctrl: pinctrl {
+					compatible = "marvell,ap806-pinctrl";
+
+					uart0_pins: uart0-pins {
+						marvell,pins = "mpp11", "mpp19";
+						marvell,function = "uart0";
+					};
+				};
+
+				ap_gpio: gpio@1040 {
+					compatible = "marvell,armada-8k-gpio";
+					offset = <0x1040>;
+					ngpios = <20>;
+					gpio-controller;
+					#gpio-cells = <2>;
+					gpio-ranges = <&ap_pinctrl 0 0 20>;
+				};
+			};
+
+			ap_syscon1: system-controller@6f8000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x6f8000 0x1000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				cpu_clk: clock-cpu@278 {
+					compatible = "marvell,ap806-cpu-clock";
+					clocks = <&ap_clk 0>, <&ap_clk 1>;
+					#clock-cells = <1>;
+					reg = <0x278 0xa30>;
+				};
+
+				ap_thermal: thermal-sensor@80 {
+					compatible = "marvell,armada-ap806-thermal";
+					reg = <0x80 0x10>;
+					interrupt-parent = <&sei>;
+					interrupts = <18>;
+					#thermal-sensor-cells = <1>;
+				};
+			};
+		};
+	};
+
+	/*
+	 * The thermal IP features one internal sensor plus, if applicable, one
+	 * remote channel wired to one sensor per CPU.
+	 *
+	 * Only one thermal zone per AP/CP may trigger interrupts at a time, the
+	 * first one that will have a critical trip point will be chosen.
+	 */
+	thermal-zones {
+		ap_thermal_ic: ap-thermal-ic {
+			polling-delay-passive = <0>; /* Interrupt driven */
+			polling-delay = <0>; /* Interrupt driven */
+
+			thermal-sensors = <&ap_thermal 0>;
+
+			trips {
+				ap_crit: ap-crit {
+					temperature = <100000>; /* mC degrees */
+					hysteresis = <2000>; /* mC degrees */
+					type = "critical";
+				};
+			};
+
+			cooling-maps { };
+		};
+
+		ap_thermal_cpu0: ap-thermal-cpu0 {
+			polling-delay-passive = <1000>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&ap_thermal 1>;
+
+			trips {
+				cpu0_hot: cpu0-hot {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu0_emerg: cpu0-emerg {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+			};
+
+			cooling-maps {
+				map0_hot: map0-hot {
+					trip = <&cpu0_hot>;
+					cooling-device = <&cpu0 1 2>,
+						<&cpu1 1 2>;
+				};
+				map0_emerg: map0-ermerg {
+					trip = <&cpu0_emerg>;
+					cooling-device = <&cpu0 3 3>,
+						<&cpu1 3 3>;
+				};
+			};
+		};
+
+		ap_thermal_cpu1: ap-thermal-cpu1 {
+			polling-delay-passive = <1000>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&ap_thermal 2>;
+
+			trips {
+				cpu1_hot: cpu1-hot {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu1_emerg: cpu1-emerg {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+			};
+
+			cooling-maps {
+				map1_hot: map1-hot {
+					trip = <&cpu1_hot>;
+					cooling-device = <&cpu0 1 2>,
+						<&cpu1 1 2>;
+				};
+				map1_emerg: map1-emerg {
+					trip = <&cpu1_emerg>;
+					cooling-device = <&cpu0 3 3>,
+						<&cpu1 3 3>;
+				};
+			};
+		};
+
+		ap_thermal_cpu2: ap-thermal-cpu2 {
+			polling-delay-passive = <1000>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&ap_thermal 3>;
+
+			trips {
+				cpu2_hot: cpu2-hot {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu2_emerg: cpu2-emerg {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+			};
+
+			cooling-maps {
+				map2_hot: map2-hot {
+					trip = <&cpu2_hot>;
+					cooling-device = <&cpu2 1 2>,
+						<&cpu3 1 2>;
+				};
+				map2_emerg: map2-emerg {
+					trip = <&cpu2_emerg>;
+					cooling-device = <&cpu2 3 3>,
+						<&cpu3 3 3>;
+				};
+			};
+		};
+
+		ap_thermal_cpu3: ap-thermal-cpu3 {
+			polling-delay-passive = <1000>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&ap_thermal 4>;
+
+			trips {
+				cpu3_hot: cpu3-hot {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu3_emerg: cpu3-emerg {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+			};
+
+			cooling-maps {
+				map3_hot: map3-bhot {
+					trip = <&cpu3_hot>;
+					cooling-device = <&cpu2 1 2>,
+						<&cpu3 1 2>;
+				};
+				map3_emerg: map3-emerg {
+					trip = <&cpu3_emerg>;
+					cooling-device = <&cpu2 3 3>,
+						<&cpu3 3 3>;
+				};
+			};
+		};
+	};
+};
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 25+ messages in thread

* [PATCH 06/20] arm64: dts: marvell: Move clocks to AP806 specific file
  2019-08-06 14:54 [PATCH 00/20] Add new Marvell CN9130 SoC support Miquel Raynal
                   ` (4 preceding siblings ...)
  2019-08-06 14:54 ` [PATCH 05/20] arm64: dts: marvell: Prepare the introduction of AP807 based SoCs Miquel Raynal
@ 2019-08-06 14:54 ` Miquel Raynal
  2019-08-06 14:54 ` [PATCH 07/20] arm64: dts: marvell: Add support for AP807/AP807-quad Miquel Raynal
                   ` (13 subsequent siblings)
  19 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-08-06 14:54 UTC (permalink / raw)
  To: Rob Herring, Mark Rutland
  Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
	Gregory Clement, Maxime Chevallier, Nadav Haklai,
	Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
	linux-arm-kernel

Regular clocks and CPU clocks are specific to AP806, move them out of
the generic AP80x file so that AP807 can use its own clocks.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 arch/arm64/boot/dts/marvell/armada-ap806.dtsi | 16 ++++++++++++++++
 arch/arm64/boot/dts/marvell/armada-ap80x.dtsi | 12 ------------
 2 files changed, 16 insertions(+), 12 deletions(-)

diff --git a/arch/arm64/boot/dts/marvell/armada-ap806.dtsi b/arch/arm64/boot/dts/marvell/armada-ap806.dtsi
index cdadb28f287e..866628679ac7 100644
--- a/arch/arm64/boot/dts/marvell/armada-ap806.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-ap806.dtsi
@@ -12,3 +12,19 @@
 	model = "Marvell Armada AP806";
 	compatible = "marvell,armada-ap806";
 };
+
+&ap_syscon0 {
+	ap_clk: clock {
+		compatible = "marvell,ap806-clock";
+		#clock-cells = <1>;
+	};
+};
+
+&ap_syscon1 {
+	cpu_clk: clock-cpu@278 {
+		compatible = "marvell,ap806-cpu-clock";
+		clocks = <&ap_clk 0>, <&ap_clk 1>;
+		#clock-cells = <1>;
+		reg = <0x278 0xa30>;
+	};
+};
diff --git a/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi b/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi
index c44cd7c64bf6..b74b5cf724be 100644
--- a/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi
@@ -248,11 +248,6 @@
 				compatible = "syscon", "simple-mfd";
 				reg = <0x6f4000 0x2000>;
 
-				ap_clk: clock {
-					compatible = "marvell,ap806-clock";
-					#clock-cells = <1>;
-				};
-
 				ap_pinctrl: pinctrl {
 					compatible = "marvell,ap806-pinctrl";
 
@@ -278,13 +273,6 @@
 				#address-cells = <1>;
 				#size-cells = <1>;
 
-				cpu_clk: clock-cpu@278 {
-					compatible = "marvell,ap806-cpu-clock";
-					clocks = <&ap_clk 0>, <&ap_clk 1>;
-					#clock-cells = <1>;
-					reg = <0x278 0xa30>;
-				};
-
 				ap_thermal: thermal-sensor@80 {
 					compatible = "marvell,armada-ap806-thermal";
 					reg = <0x80 0x10>;
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 25+ messages in thread

* [PATCH 07/20] arm64: dts: marvell: Add support for AP807/AP807-quad
  2019-08-06 14:54 [PATCH 00/20] Add new Marvell CN9130 SoC support Miquel Raynal
                   ` (5 preceding siblings ...)
  2019-08-06 14:54 ` [PATCH 06/20] arm64: dts: marvell: Move clocks to AP806 specific file Miquel Raynal
@ 2019-08-06 14:54 ` Miquel Raynal
  2019-08-06 14:54 ` [PATCH 08/20] arm64: dts: marvell: Add AP806-dual cache description Miquel Raynal
                   ` (12 subsequent siblings)
  19 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-08-06 14:54 UTC (permalink / raw)
  To: Rob Herring, Mark Rutland
  Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
	Gregory Clement, Maxime Chevallier, Nadav Haklai,
	Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
	linux-arm-kernel

Describe AP807 and AP807-quad support.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 .../boot/dts/marvell/armada-ap807-quad.dtsi   | 51 +++++++++++++++++++
 arch/arm64/boot/dts/marvell/armada-ap807.dtsi | 29 +++++++++++
 2 files changed, 80 insertions(+)
 create mode 100644 arch/arm64/boot/dts/marvell/armada-ap807-quad.dtsi
 create mode 100644 arch/arm64/boot/dts/marvell/armada-ap807.dtsi

diff --git a/arch/arm64/boot/dts/marvell/armada-ap807-quad.dtsi b/arch/arm64/boot/dts/marvell/armada-ap807-quad.dtsi
new file mode 100644
index 000000000000..65364691257d
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/armada-ap807-quad.dtsi
@@ -0,0 +1,51 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for Marvell Armada AP807 Quad
+ *
+ * Copyright (C) 2019 Marvell Technology Group Ltd.
+ */
+
+#include "armada-ap807.dtsi"
+
+/ {
+	model = "Marvell Armada AP807 Quad";
+	compatible = "marvell,armada-ap807-quad", "marvell,armada-ap807";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72", "arm,armv8";
+			reg = <0x000>;
+			enable-method = "psci";
+			#cooling-cells = <2>;
+			clocks = <&cpu_clk 0>;
+		};
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72", "arm,armv8";
+			reg = <0x001>;
+			enable-method = "psci";
+			#cooling-cells = <2>;
+			clocks = <&cpu_clk 0>;
+		};
+		cpu2: cpu@100 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72", "arm,armv8";
+			reg = <0x100>;
+			enable-method = "psci";
+			#cooling-cells = <2>;
+			clocks = <&cpu_clk 1>;
+		};
+		cpu3: cpu@101 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72", "arm,armv8";
+			reg = <0x101>;
+			enable-method = "psci";
+			#cooling-cells = <2>;
+			clocks = <&cpu_clk 1>;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/marvell/armada-ap807.dtsi b/arch/arm64/boot/dts/marvell/armada-ap807.dtsi
new file mode 100644
index 000000000000..623010f3ca89
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/armada-ap807.dtsi
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for Marvell Armada AP807
+ *
+ * Copyright (C) 2019 Marvell Technology Group Ltd.
+ */
+
+#define AP_NAME		ap807
+#include "armada-ap80x.dtsi"
+
+/ {
+	model = "Marvell Armada AP807";
+	compatible = "marvell,armada-ap807";
+};
+
+&ap_syscon0 {
+	ap_clk: clock {
+		compatible = "marvell,ap807-clock";
+		#clock-cells = <1>;
+	};
+};
+
+&ap_syscon1 {
+	cpu_clk: clock-cpu {
+		compatible = "marvell,ap807-cpu-clock";
+		clocks = <&ap_clk 0>, <&ap_clk 1>;
+		#clock-cells = <1>;
+	};
+};
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 25+ messages in thread

* [PATCH 08/20] arm64: dts: marvell: Add AP806-dual cache description
  2019-08-06 14:54 [PATCH 00/20] Add new Marvell CN9130 SoC support Miquel Raynal
                   ` (6 preceding siblings ...)
  2019-08-06 14:54 ` [PATCH 07/20] arm64: dts: marvell: Add support for AP807/AP807-quad Miquel Raynal
@ 2019-08-06 14:54 ` Miquel Raynal
  2019-08-06 14:54 ` [PATCH 09/20] arm64: dts: marvell: Add AP806-quad " Miquel Raynal
                   ` (11 subsequent siblings)
  19 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-08-06 14:54 UTC (permalink / raw)
  To: Rob Herring, Mark Rutland
  Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
	Gregory Clement, Maxime Chevallier, Nadav Haklai,
	Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
	linux-arm-kernel

From: Grzegorz Jaszczyk <jaz@semihalf.com>

Adding appropriate entries to device-tree allows the cache description
to show up in sysfs under: /sys/devices/system/cpu/cpuX/cache/.

Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 .../boot/dts/marvell/armada-ap806-dual.dtsi   | 21 +++++++++++++++++++
 1 file changed, 21 insertions(+)

diff --git a/arch/arm64/boot/dts/marvell/armada-ap806-dual.dtsi b/arch/arm64/boot/dts/marvell/armada-ap806-dual.dtsi
index 62ae016ee6aa..09849558a776 100644
--- a/arch/arm64/boot/dts/marvell/armada-ap806-dual.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-ap806-dual.dtsi
@@ -22,6 +22,13 @@
 			enable-method = "psci";
 			#cooling-cells = <2>;
 			clocks = <&cpu_clk 0>;
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&l2>;
 		};
 		cpu1: cpu@1 {
 			device_type = "cpu";
@@ -30,6 +37,20 @@
 			enable-method = "psci";
 			#cooling-cells = <2>;
 			clocks = <&cpu_clk 0>;
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&l2>;
+		};
+
+		l2: l2-cache {
+			compatible = "cache";
+			cache-size = <0x80000>;
+			cache-line-size = <64>;
+			cache-sets = <512>;
 		};
 	};
 };
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 25+ messages in thread

* [PATCH 09/20] arm64: dts: marvell: Add AP806-quad cache description
  2019-08-06 14:54 [PATCH 00/20] Add new Marvell CN9130 SoC support Miquel Raynal
                   ` (7 preceding siblings ...)
  2019-08-06 14:54 ` [PATCH 08/20] arm64: dts: marvell: Add AP806-dual cache description Miquel Raynal
@ 2019-08-06 14:54 ` " Miquel Raynal
  2019-08-06 14:54 ` [PATCH 10/20] arm64: dts: marvell: Add AP807-quad " Miquel Raynal
                   ` (10 subsequent siblings)
  19 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-08-06 14:54 UTC (permalink / raw)
  To: Rob Herring, Mark Rutland
  Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
	Gregory Clement, Maxime Chevallier, Nadav Haklai,
	Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
	linux-arm-kernel

From: Grzegorz Jaszczyk <jaz@semihalf.com>

Adding appropriate entries to device-tree allows the cache description
to show up in sysfs under: /sys/devices/system/cpu/cpuX/cache/.

Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 .../boot/dts/marvell/armada-ap806-quad.dtsi   | 42 +++++++++++++++++++
 1 file changed, 42 insertions(+)

diff --git a/arch/arm64/boot/dts/marvell/armada-ap806-quad.dtsi b/arch/arm64/boot/dts/marvell/armada-ap806-quad.dtsi
index 2f1a968b1b6b..2984bd9cf6ae 100644
--- a/arch/arm64/boot/dts/marvell/armada-ap806-quad.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-ap806-quad.dtsi
@@ -22,6 +22,13 @@
 			enable-method = "psci";
 			#cooling-cells = <2>;
 			clocks = <&cpu_clk 0>;
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&l2_0>;
 		};
 		cpu1: cpu@1 {
 			device_type = "cpu";
@@ -30,6 +37,13 @@
 			enable-method = "psci";
 			#cooling-cells = <2>;
 			clocks = <&cpu_clk 0>;
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&l2_0>;
 		};
 		cpu2: cpu@100 {
 			device_type = "cpu";
@@ -38,6 +52,13 @@
 			enable-method = "psci";
 			#cooling-cells = <2>;
 			clocks = <&cpu_clk 1>;
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&l2_1>;
 		};
 		cpu3: cpu@101 {
 			device_type = "cpu";
@@ -46,6 +67,27 @@
 			enable-method = "psci";
 			#cooling-cells = <2>;
 			clocks = <&cpu_clk 1>;
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&l2_1>;
+		};
+
+		l2_0: l2-cache0 {
+			compatible = "cache";
+			cache-size = <0x80000>;
+			cache-line-size = <64>;
+			cache-sets = <512>;
+		};
+
+		l2_1: l2-cache1 {
+			compatible = "cache";
+			cache-size = <0x80000>;
+			cache-line-size = <64>;
+			cache-sets = <512>;
 		};
 	};
 
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 25+ messages in thread

* [PATCH 10/20] arm64: dts: marvell: Add AP807-quad cache description
  2019-08-06 14:54 [PATCH 00/20] Add new Marvell CN9130 SoC support Miquel Raynal
                   ` (8 preceding siblings ...)
  2019-08-06 14:54 ` [PATCH 09/20] arm64: dts: marvell: Add AP806-quad " Miquel Raynal
@ 2019-08-06 14:54 ` " Miquel Raynal
  2019-08-06 14:54 ` [PATCH 11/20] arm64: dts: marvell: Fix CP110 NAND controller node multi-line comment alignment Miquel Raynal
                   ` (9 subsequent siblings)
  19 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-08-06 14:54 UTC (permalink / raw)
  To: Rob Herring, Mark Rutland
  Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
	Gregory Clement, Maxime Chevallier, Nadav Haklai,
	Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
	linux-arm-kernel

From: Grzegorz Jaszczyk <jaz@semihalf.com>

Adding appropriate entries to device-tree allows the cache description
to show up in sysfs under: /sys/devices/system/cpu/cpuX/cache/.

Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 .../boot/dts/marvell/armada-ap807-quad.dtsi   | 42 +++++++++++++++++++
 1 file changed, 42 insertions(+)

diff --git a/arch/arm64/boot/dts/marvell/armada-ap807-quad.dtsi b/arch/arm64/boot/dts/marvell/armada-ap807-quad.dtsi
index 65364691257d..840466e143b4 100644
--- a/arch/arm64/boot/dts/marvell/armada-ap807-quad.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-ap807-quad.dtsi
@@ -22,6 +22,13 @@
 			enable-method = "psci";
 			#cooling-cells = <2>;
 			clocks = <&cpu_clk 0>;
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&l2_0>;
 		};
 		cpu1: cpu@1 {
 			device_type = "cpu";
@@ -30,6 +37,13 @@
 			enable-method = "psci";
 			#cooling-cells = <2>;
 			clocks = <&cpu_clk 0>;
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&l2_0>;
 		};
 		cpu2: cpu@100 {
 			device_type = "cpu";
@@ -38,6 +52,13 @@
 			enable-method = "psci";
 			#cooling-cells = <2>;
 			clocks = <&cpu_clk 1>;
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&l2_1>;
 		};
 		cpu3: cpu@101 {
 			device_type = "cpu";
@@ -46,6 +67,27 @@
 			enable-method = "psci";
 			#cooling-cells = <2>;
 			clocks = <&cpu_clk 1>;
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&l2_1>;
+		};
+
+		l2_0: l2-cache0 {
+			compatible = "cache";
+			cache-size = <0x80000>;
+			cache-line-size = <64>;
+			cache-sets = <512>;
+		};
+
+		l2_1: l2-cache1 {
+			compatible = "cache";
+			cache-size = <0x80000>;
+			cache-line-size = <64>;
+			cache-sets = <512>;
 		};
 	};
 };
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 25+ messages in thread

* [PATCH 11/20] arm64: dts: marvell: Fix CP110 NAND controller node multi-line comment alignment
  2019-08-06 14:54 [PATCH 00/20] Add new Marvell CN9130 SoC support Miquel Raynal
                   ` (9 preceding siblings ...)
  2019-08-06 14:54 ` [PATCH 10/20] arm64: dts: marvell: Add AP807-quad " Miquel Raynal
@ 2019-08-06 14:54 ` Miquel Raynal
  2019-08-06 14:54 ` [PATCH 12/20] arm64: dts: marvell: Prepare the introduction of CP115 Miquel Raynal
                   ` (8 subsequent siblings)
  19 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-08-06 14:54 UTC (permalink / raw)
  To: Rob Herring, Mark Rutland
  Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
	Gregory Clement, Maxime Chevallier, Nadav Haklai,
	Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
	linux-arm-kernel

Fix this tiny typo before renaming/changing this file.

Fixes: 72a3713fadfd ("arm64: dts: marvell: de-duplicate CP110 description")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 arch/arm64/boot/dts/marvell/armada-cp110.dtsi | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/marvell/armada-cp110.dtsi b/arch/arm64/boot/dts/marvell/armada-cp110.dtsi
index d81944902650..8259fc8f86f2 100644
--- a/arch/arm64/boot/dts/marvell/armada-cp110.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-cp110.dtsi
@@ -438,10 +438,10 @@
 
 		CP110_LABEL(nand_controller): nand@720000 {
 			/*
-			* Due to the limitation of the pins available
-			* this controller is only usable on the CPM
-			* for A7K and on the CPS for A8K.
-			*/
+			 * Due to the limitation of the pins available
+			 * this controller is only usable on the CPM
+			 * for A7K and on the CPS for A8K.
+			 */
 			compatible = "marvell,armada-8k-nand-controller",
 				"marvell,armada370-nand-controller";
 			reg = <0x720000 0x54>;
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 25+ messages in thread

* [PATCH 12/20] arm64: dts: marvell: Prepare the introduction of CP115
  2019-08-06 14:54 [PATCH 00/20] Add new Marvell CN9130 SoC support Miquel Raynal
                   ` (10 preceding siblings ...)
  2019-08-06 14:54 ` [PATCH 11/20] arm64: dts: marvell: Fix CP110 NAND controller node multi-line comment alignment Miquel Raynal
@ 2019-08-06 14:54 ` Miquel Raynal
  2019-08-06 14:54 ` [PATCH 13/20] arm64: dts: marvell: Drop PCIe I/O ranges from CP11x file Miquel Raynal
                   ` (7 subsequent siblings)
  19 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-08-06 14:54 UTC (permalink / raw)
  To: Rob Herring, Mark Rutland
  Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
	Gregory Clement, Maxime Chevallier, Nadav Haklai,
	Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
	linux-arm-kernel

CP110 and CP115 are almost the same in terms of features and have a
very limited set of differences. Let's create an armada-cp11x.dtsi
file which will be used to instantiate both CP110 and CP115
nodes.

The only changes between the two armada-cp11{0,x}.dtsi files are the
following naming in macros: s/CP110/CP11X/.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 arch/arm64/boot/dts/marvell/armada-70x0.dtsi  |  28 +-
 arch/arm64/boot/dts/marvell/armada-80x0.dtsi  |  56 +-
 .../arm64/boot/dts/marvell/armada-common.dtsi |   4 +-
 arch/arm64/boot/dts/marvell/armada-cp110.dtsi | 575 +----------------
 arch/arm64/boot/dts/marvell/armada-cp11x.dtsi | 579 ++++++++++++++++++
 5 files changed, 627 insertions(+), 615 deletions(-)
 create mode 100644 arch/arm64/boot/dts/marvell/armada-cp11x.dtsi

diff --git a/arch/arm64/boot/dts/marvell/armada-70x0.dtsi b/arch/arm64/boot/dts/marvell/armada-70x0.dtsi
index e5c6d7c25819..4e78ccd207b7 100644
--- a/arch/arm64/boot/dts/marvell/armada-70x0.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-70x0.dtsi
@@ -17,23 +17,23 @@
 /*
  * Instantiate the CP110
  */
-#define CP110_NAME		cp0
-#define CP110_BASE		f2000000
-#define CP110_PCIE_IO_BASE	0xf9000000
-#define CP110_PCIE_MEM_BASE	0xf6000000
-#define CP110_PCIE0_BASE	f2600000
-#define CP110_PCIE1_BASE	f2620000
-#define CP110_PCIE2_BASE	f2640000
+#define CP11X_NAME		cp0
+#define CP11X_BASE		f2000000
+#define CP11X_PCIE_IO_BASE	0xf9000000
+#define CP11X_PCIE_MEM_BASE	0xf6000000
+#define CP11X_PCIE0_BASE	f2600000
+#define CP11X_PCIE1_BASE	f2620000
+#define CP11X_PCIE2_BASE	f2640000
 
 #include "armada-cp110.dtsi"
 
-#undef CP110_NAME
-#undef CP110_BASE
-#undef CP110_PCIE_IO_BASE
-#undef CP110_PCIE_MEM_BASE
-#undef CP110_PCIE0_BASE
-#undef CP110_PCIE1_BASE
-#undef CP110_PCIE2_BASE
+#undef CP11X_NAME
+#undef CP11X_BASE
+#undef CP11X_PCIE_IO_BASE
+#undef CP11X_PCIE_MEM_BASE
+#undef CP11X_PCIE0_BASE
+#undef CP11X_PCIE1_BASE
+#undef CP11X_PCIE2_BASE
 
 &cp0_gpio1 {
 	status = "okay";
diff --git a/arch/arm64/boot/dts/marvell/armada-80x0.dtsi b/arch/arm64/boot/dts/marvell/armada-80x0.dtsi
index 8129b40f12a4..ebb98836ec9c 100644
--- a/arch/arm64/boot/dts/marvell/armada-80x0.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-80x0.dtsi
@@ -19,44 +19,44 @@
 /*
  * Instantiate the master CP110
  */
-#define CP110_NAME		cp0
-#define CP110_BASE		f2000000
-#define CP110_PCIE_IO_BASE	0xf9000000
-#define CP110_PCIE_MEM_BASE	0xf6000000
-#define CP110_PCIE0_BASE	f2600000
-#define CP110_PCIE1_BASE	f2620000
-#define CP110_PCIE2_BASE	f2640000
+#define CP11X_NAME		cp0
+#define CP11X_BASE		f2000000
+#define CP11X_PCIE_IO_BASE	0xf9000000
+#define CP11X_PCIE_MEM_BASE	0xf6000000
+#define CP11X_PCIE0_BASE	f2600000
+#define CP11X_PCIE1_BASE	f2620000
+#define CP11X_PCIE2_BASE	f2640000
 
 #include "armada-cp110.dtsi"
 
-#undef CP110_NAME
-#undef CP110_BASE
-#undef CP110_PCIE_IO_BASE
-#undef CP110_PCIE_MEM_BASE
-#undef CP110_PCIE0_BASE
-#undef CP110_PCIE1_BASE
-#undef CP110_PCIE2_BASE
+#undef CP11X_NAME
+#undef CP11X_BASE
+#undef CP11X_PCIE_IO_BASE
+#undef CP11X_PCIE_MEM_BASE
+#undef CP11X_PCIE0_BASE
+#undef CP11X_PCIE1_BASE
+#undef CP11X_PCIE2_BASE
 
 /*
  * Instantiate the slave CP110
  */
-#define CP110_NAME		cp1
-#define CP110_BASE		f4000000
-#define CP110_PCIE_IO_BASE	0xfd000000
-#define CP110_PCIE_MEM_BASE	0xfa000000
-#define CP110_PCIE0_BASE	f4600000
-#define CP110_PCIE1_BASE	f4620000
-#define CP110_PCIE2_BASE	f4640000
+#define CP11X_NAME		cp1
+#define CP11X_BASE		f4000000
+#define CP11X_PCIE_IO_BASE	0xfd000000
+#define CP11X_PCIE_MEM_BASE	0xfa000000
+#define CP11X_PCIE0_BASE	f4600000
+#define CP11X_PCIE1_BASE	f4620000
+#define CP11X_PCIE2_BASE	f4640000
 
 #include "armada-cp110.dtsi"
 
-#undef CP110_NAME
-#undef CP110_BASE
-#undef CP110_PCIE_IO_BASE
-#undef CP110_PCIE_MEM_BASE
-#undef CP110_PCIE0_BASE
-#undef CP110_PCIE1_BASE
-#undef CP110_PCIE2_BASE
+#undef CP11X_NAME
+#undef CP11X_BASE
+#undef CP11X_PCIE_IO_BASE
+#undef CP11X_PCIE_MEM_BASE
+#undef CP11X_PCIE0_BASE
+#undef CP11X_PCIE1_BASE
+#undef CP11X_PCIE2_BASE
 
 /* The 80x0 has two CP blocks, but uses only one block from each. */
 &cp1_gpio1 {
diff --git a/arch/arm64/boot/dts/marvell/armada-common.dtsi b/arch/arm64/boot/dts/marvell/armada-common.dtsi
index b29c6405d214..c04c6c475022 100644
--- a/arch/arm64/boot/dts/marvell/armada-common.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-common.dtsi
@@ -6,6 +6,6 @@
 /* Common definitions used by Armada 7K/8K DTs */
 #define PASTER(x, y) x ## y
 #define EVALUATOR(x, y) PASTER(x, y)
-#define CP110_LABEL(name) EVALUATOR(CP110_NAME, EVALUATOR(_, name))
-#define CP110_NODE_NAME(name) EVALUATOR(CP110_NAME, EVALUATOR(-, name))
+#define CP11X_LABEL(name) EVALUATOR(CP11X_NAME, EVALUATOR(_, name))
+#define CP11X_NODE_NAME(name) EVALUATOR(CP11X_NAME, EVALUATOR(-, name))
 #define ADDRESSIFY(addr) EVALUATOR(0x, addr)
diff --git a/arch/arm64/boot/dts/marvell/armada-cp110.dtsi b/arch/arm64/boot/dts/marvell/armada-cp110.dtsi
index 8259fc8f86f2..4fd33b0fa56e 100644
--- a/arch/arm64/boot/dts/marvell/armada-cp110.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-cp110.dtsi
@@ -1,579 +1,12 @@
 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
 /*
- * Copyright (C) 2016 Marvell Technology Group Ltd.
+ * Copyright (C) 2019 Marvell Technology Group Ltd.
  *
  * Device Tree file for Marvell Armada CP110.
  */
 
-#include <dt-bindings/interrupt-controller/mvebu-icu.h>
-#include <dt-bindings/thermal/thermal.h>
+#define CP11X_TYPE cp110
 
-#include "armada-common.dtsi"
+#include "armada-cp11x.dtsi"
 
-#define CP110_PCIEx_IO_BASE(iface)	(CP110_PCIE_IO_BASE + (iface *  0x10000))
-#define CP110_PCIEx_MEM_BASE(iface)	(CP110_PCIE_MEM_BASE + (iface *  0x1000000))
-#define CP110_PCIEx_CONF_BASE(iface)	(CP110_PCIEx_MEM_BASE(iface) + 0xf00000)
-
-/ {
-	/*
-	 * The contents of the node are defined below, in order to
-	 * save one indentation level
-	 */
-	CP110_NAME: CP110_NAME { };
-
-	/*
-	 * CPs only have one sensor in the thermal IC.
-	 *
-	 * The cooling maps are empty as there are no cooling devices.
-	 */
-	thermal-zones {
-		CP110_LABEL(thermal_ic): CP110_NODE_NAME(thermal-ic) {
-			polling-delay-passive = <0>; /* Interrupt driven */
-			polling-delay = <0>; /* Interrupt driven */
-
-			thermal-sensors = <&CP110_LABEL(thermal) 0>;
-
-			trips {
-				CP110_LABEL(crit): crit {
-					temperature = <100000>; /* mC degrees */
-					hysteresis = <2000>; /* mC degrees */
-					type = "critical";
-				};
-			};
-
-			cooling-maps { };
-		};
-	};
-};
-
-&CP110_NAME {
-	#address-cells = <2>;
-	#size-cells = <2>;
-	compatible = "simple-bus";
-	interrupt-parent = <&CP110_LABEL(icu_nsr)>;
-	ranges;
-
-	config-space@CP110_BASE {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "simple-bus";
-		ranges = <0x0 0x0 ADDRESSIFY(CP110_BASE) 0x2000000>;
-
-		CP110_LABEL(ethernet): ethernet@0 {
-			compatible = "marvell,armada-7k-pp22";
-			reg = <0x0 0x100000>, <0x129000 0xb000>;
-			clocks = <&CP110_LABEL(clk) 1 3>, <&CP110_LABEL(clk) 1 9>,
-				 <&CP110_LABEL(clk) 1 5>, <&CP110_LABEL(clk) 1 6>,
-				 <&CP110_LABEL(clk) 1 18>;
-			clock-names = "pp_clk", "gop_clk",
-				      "mg_clk", "mg_core_clk", "axi_clk";
-			marvell,system-controller = <&CP110_LABEL(syscon0)>;
-			status = "disabled";
-			dma-coherent;
-
-			CP110_LABEL(eth0): eth0 {
-				interrupts = <39 IRQ_TYPE_LEVEL_HIGH>,
-					<43 IRQ_TYPE_LEVEL_HIGH>,
-					<47 IRQ_TYPE_LEVEL_HIGH>,
-					<51 IRQ_TYPE_LEVEL_HIGH>,
-					<55 IRQ_TYPE_LEVEL_HIGH>,
-					<59 IRQ_TYPE_LEVEL_HIGH>,
-					<63 IRQ_TYPE_LEVEL_HIGH>,
-					<67 IRQ_TYPE_LEVEL_HIGH>,
-					<71 IRQ_TYPE_LEVEL_HIGH>,
-					<129 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names = "hif0", "hif1", "hif2",
-					"hif3", "hif4", "hif5", "hif6", "hif7",
-					"hif8", "link";
-				port-id = <0>;
-				gop-port-id = <0>;
-				status = "disabled";
-			};
-
-			CP110_LABEL(eth1): eth1 {
-				interrupts = <40 IRQ_TYPE_LEVEL_HIGH>,
-					<44 IRQ_TYPE_LEVEL_HIGH>,
-					<48 IRQ_TYPE_LEVEL_HIGH>,
-					<52 IRQ_TYPE_LEVEL_HIGH>,
-					<56 IRQ_TYPE_LEVEL_HIGH>,
-					<60 IRQ_TYPE_LEVEL_HIGH>,
-					<64 IRQ_TYPE_LEVEL_HIGH>,
-					<68 IRQ_TYPE_LEVEL_HIGH>,
-					<72 IRQ_TYPE_LEVEL_HIGH>,
-					<128 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names = "hif0", "hif1", "hif2",
-					"hif3", "hif4", "hif5", "hif6", "hif7",
-					"hif8", "link";
-				port-id = <1>;
-				gop-port-id = <2>;
-				status = "disabled";
-			};
-
-			CP110_LABEL(eth2): eth2 {
-				interrupts = <41 IRQ_TYPE_LEVEL_HIGH>,
-					<45 IRQ_TYPE_LEVEL_HIGH>,
-					<49 IRQ_TYPE_LEVEL_HIGH>,
-					<53 IRQ_TYPE_LEVEL_HIGH>,
-					<57 IRQ_TYPE_LEVEL_HIGH>,
-					<61 IRQ_TYPE_LEVEL_HIGH>,
-					<65 IRQ_TYPE_LEVEL_HIGH>,
-					<69 IRQ_TYPE_LEVEL_HIGH>,
-					<73 IRQ_TYPE_LEVEL_HIGH>,
-					<127 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names = "hif0", "hif1", "hif2",
-					"hif3", "hif4", "hif5", "hif6", "hif7",
-					"hif8", "link";
-				port-id = <2>;
-				gop-port-id = <3>;
-				status = "disabled";
-			};
-		};
-
-		CP110_LABEL(comphy): phy@120000 {
-			compatible = "marvell,comphy-cp110";
-			reg = <0x120000 0x6000>;
-			marvell,system-controller = <&CP110_LABEL(syscon0)>;
-			clocks = <&CP110_LABEL(clk) 1 5>, <&CP110_LABEL(clk) 1 6>,
-				 <&CP110_LABEL(clk) 1 18>;
-			clock-names = "mg_clk", "mg_core_clk", "axi_clk";
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			CP110_LABEL(comphy0): phy@0 {
-				reg = <0>;
-				#phy-cells = <1>;
-			};
-
-			CP110_LABEL(comphy1): phy@1 {
-				reg = <1>;
-				#phy-cells = <1>;
-			};
-
-			CP110_LABEL(comphy2): phy@2 {
-				reg = <2>;
-				#phy-cells = <1>;
-			};
-
-			CP110_LABEL(comphy3): phy@3 {
-				reg = <3>;
-				#phy-cells = <1>;
-			};
-
-			CP110_LABEL(comphy4): phy@4 {
-				reg = <4>;
-				#phy-cells = <1>;
-			};
-
-			CP110_LABEL(comphy5): phy@5 {
-				reg = <5>;
-				#phy-cells = <1>;
-			};
-		};
-
-		CP110_LABEL(mdio): mdio@12a200 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "marvell,orion-mdio";
-			reg = <0x12a200 0x10>;
-			clocks = <&CP110_LABEL(clk) 1 9>, <&CP110_LABEL(clk) 1 5>,
-				 <&CP110_LABEL(clk) 1 6>, <&CP110_LABEL(clk) 1 18>;
-			status = "disabled";
-		};
-
-		CP110_LABEL(xmdio): mdio@12a600 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "marvell,xmdio";
-			reg = <0x12a600 0x10>;
-			clocks = <&CP110_LABEL(clk) 1 5>,
-				 <&CP110_LABEL(clk) 1 6>, <&CP110_LABEL(clk) 1 18>;
-			status = "disabled";
-		};
-
-		CP110_LABEL(icu): interrupt-controller@1e0000 {
-			compatible = "marvell,cp110-icu";
-			reg = <0x1e0000 0x440>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			CP110_LABEL(icu_nsr): interrupt-controller@10 {
-				compatible = "marvell,cp110-icu-nsr";
-				reg = <0x10 0x20>;
-				#interrupt-cells = <2>;
-				interrupt-controller;
-				msi-parent = <&gicp>;
-			};
-
-			CP110_LABEL(icu_sei): interrupt-controller@50 {
-				compatible = "marvell,cp110-icu-sei";
-				reg = <0x50 0x10>;
-				#interrupt-cells = <2>;
-				interrupt-controller;
-				msi-parent = <&sei>;
-			};
-		};
-
-		CP110_LABEL(rtc): rtc@284000 {
-			compatible = "marvell,armada-8k-rtc";
-			reg = <0x284000 0x20>, <0x284080 0x24>;
-			reg-names = "rtc", "rtc-soc";
-			interrupts = <77 IRQ_TYPE_LEVEL_HIGH>;
-		};
-
-		CP110_LABEL(syscon0): system-controller@440000 {
-			compatible = "syscon", "simple-mfd";
-			reg = <0x440000 0x2000>;
-
-			CP110_LABEL(clk): clock {
-				compatible = "marvell,cp110-clock";
-				#clock-cells = <2>;
-			};
-
-			CP110_LABEL(gpio1): gpio@100 {
-				compatible = "marvell,armada-8k-gpio";
-				offset = <0x100>;
-				ngpios = <32>;
-				gpio-controller;
-				#gpio-cells = <2>;
-				gpio-ranges = <&CP110_LABEL(pinctrl) 0 0 32>;
-				interrupt-controller;
-				interrupts = <86 IRQ_TYPE_LEVEL_HIGH>,
-					<85 IRQ_TYPE_LEVEL_HIGH>,
-					<84 IRQ_TYPE_LEVEL_HIGH>,
-					<83 IRQ_TYPE_LEVEL_HIGH>;
-				#interrupt-cells = <2>;
-				status = "disabled";
-			};
-
-			CP110_LABEL(gpio2): gpio@140 {
-				compatible = "marvell,armada-8k-gpio";
-				offset = <0x140>;
-				ngpios = <31>;
-				gpio-controller;
-				#gpio-cells = <2>;
-				gpio-ranges = <&CP110_LABEL(pinctrl) 0 32 31>;
-				interrupt-controller;
-				interrupts = <82 IRQ_TYPE_LEVEL_HIGH>,
-					<81 IRQ_TYPE_LEVEL_HIGH>,
-					<80 IRQ_TYPE_LEVEL_HIGH>,
-					<79 IRQ_TYPE_LEVEL_HIGH>;
-				#interrupt-cells = <2>;
-				status = "disabled";
-			};
-		};
-
-		CP110_LABEL(syscon1): system-controller@400000 {
-			compatible = "syscon", "simple-mfd";
-			reg = <0x400000 0x1000>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			CP110_LABEL(thermal): thermal-sensor@70 {
-				compatible = "marvell,armada-cp110-thermal";
-				reg = <0x70 0x10>;
-				interrupts-extended =
-					<&CP110_LABEL(icu_sei) 116 IRQ_TYPE_LEVEL_HIGH>;
-				#thermal-sensor-cells = <1>;
-			};
-		};
-
-		CP110_LABEL(usb3_0): usb3@500000 {
-			compatible = "marvell,armada-8k-xhci",
-			"generic-xhci";
-			reg = <0x500000 0x4000>;
-			dma-coherent;
-			interrupts = <106 IRQ_TYPE_LEVEL_HIGH>;
-			clock-names = "core", "reg";
-			clocks = <&CP110_LABEL(clk) 1 22>,
-				 <&CP110_LABEL(clk) 1 16>;
-			status = "disabled";
-		};
-
-		CP110_LABEL(usb3_1): usb3@510000 {
-			compatible = "marvell,armada-8k-xhci",
-			"generic-xhci";
-			reg = <0x510000 0x4000>;
-			dma-coherent;
-			interrupts = <105 IRQ_TYPE_LEVEL_HIGH>;
-			clock-names = "core", "reg";
-			clocks = <&CP110_LABEL(clk) 1 23>,
-				 <&CP110_LABEL(clk) 1 16>;
-			status = "disabled";
-		};
-
-		CP110_LABEL(sata0): sata@540000 {
-			compatible = "marvell,armada-8k-ahci",
-			"generic-ahci";
-			reg = <0x540000 0x30000>;
-			dma-coherent;
-			interrupts = <107 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&CP110_LABEL(clk) 1 15>,
-				 <&CP110_LABEL(clk) 1 16>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			status = "disabled";
-
-			sata-port@0 {
-				reg = <0>;
-			};
-
-			sata-port@1 {
-				reg = <1>;
-			};
-		};
-
-		CP110_LABEL(xor0): xor@6a0000 {
-			compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
-			reg = <0x6a0000 0x1000>, <0x6b0000 0x1000>;
-			dma-coherent;
-			msi-parent = <&gic_v2m0>;
-			clock-names = "core", "reg";
-			clocks = <&CP110_LABEL(clk) 1 8>,
-				 <&CP110_LABEL(clk) 1 14>;
-		};
-
-		CP110_LABEL(xor1): xor@6c0000 {
-			compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
-			reg = <0x6c0000 0x1000>, <0x6d0000 0x1000>;
-			dma-coherent;
-			msi-parent = <&gic_v2m0>;
-			clock-names = "core", "reg";
-			clocks = <&CP110_LABEL(clk) 1 7>,
-				 <&CP110_LABEL(clk) 1 14>;
-		};
-
-		CP110_LABEL(spi0): spi@700600 {
-			compatible = "marvell,armada-380-spi";
-			reg = <0x700600 0x50>;
-			#address-cells = <0x1>;
-			#size-cells = <0x0>;
-			clock-names = "core", "axi";
-			clocks = <&CP110_LABEL(clk) 1 21>,
-				 <&CP110_LABEL(clk) 1 17>;
-			status = "disabled";
-		};
-
-		CP110_LABEL(spi1): spi@700680 {
-			compatible = "marvell,armada-380-spi";
-			reg = <0x700680 0x50>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			clock-names = "core", "axi";
-			clocks = <&CP110_LABEL(clk) 1 21>,
-				 <&CP110_LABEL(clk) 1 17>;
-			status = "disabled";
-		};
-
-		CP110_LABEL(i2c0): i2c@701000 {
-			compatible = "marvell,mv78230-i2c";
-			reg = <0x701000 0x20>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			interrupts = <120 IRQ_TYPE_LEVEL_HIGH>;
-			clock-names = "core", "reg";
-			clocks = <&CP110_LABEL(clk) 1 21>,
-				 <&CP110_LABEL(clk) 1 17>;
-			status = "disabled";
-		};
-
-		CP110_LABEL(i2c1): i2c@701100 {
-			compatible = "marvell,mv78230-i2c";
-			reg = <0x701100 0x20>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			interrupts = <121 IRQ_TYPE_LEVEL_HIGH>;
-			clock-names = "core", "reg";
-			clocks = <&CP110_LABEL(clk) 1 21>,
-				 <&CP110_LABEL(clk) 1 17>;
-			status = "disabled";
-		};
-
-		CP110_LABEL(uart0): serial@702000 {
-			compatible = "snps,dw-apb-uart";
-			reg = <0x702000 0x100>;
-			reg-shift = <2>;
-			interrupts = <122 IRQ_TYPE_LEVEL_HIGH>;
-			reg-io-width = <1>;
-			clock-names = "baudclk", "apb_pclk";
-			clocks = <&CP110_LABEL(clk) 1 21>,
-				 <&CP110_LABEL(clk) 1 17>;
-			status = "disabled";
-		};
-
-		CP110_LABEL(uart1): serial@702100 {
-			compatible = "snps,dw-apb-uart";
-			reg = <0x702100 0x100>;
-			reg-shift = <2>;
-			interrupts = <123 IRQ_TYPE_LEVEL_HIGH>;
-			reg-io-width = <1>;
-			clock-names = "baudclk", "apb_pclk";
-			clocks = <&CP110_LABEL(clk) 1 21>,
-				 <&CP110_LABEL(clk) 1 17>;
-			status = "disabled";
-		};
-
-		CP110_LABEL(uart2): serial@702200 {
-			compatible = "snps,dw-apb-uart";
-			reg = <0x702200 0x100>;
-			reg-shift = <2>;
-			interrupts = <124 IRQ_TYPE_LEVEL_HIGH>;
-			reg-io-width = <1>;
-			clock-names = "baudclk", "apb_pclk";
-			clocks = <&CP110_LABEL(clk) 1 21>,
-				 <&CP110_LABEL(clk) 1 17>;
-			status = "disabled";
-		};
-
-		CP110_LABEL(uart3): serial@702300 {
-			compatible = "snps,dw-apb-uart";
-			reg = <0x702300 0x100>;
-			reg-shift = <2>;
-			interrupts = <125 IRQ_TYPE_LEVEL_HIGH>;
-			reg-io-width = <1>;
-			clock-names = "baudclk", "apb_pclk";
-			clocks = <&CP110_LABEL(clk) 1 21>,
-				 <&CP110_LABEL(clk) 1 17>;
-			status = "disabled";
-		};
-
-		CP110_LABEL(nand_controller): nand@720000 {
-			/*
-			 * Due to the limitation of the pins available
-			 * this controller is only usable on the CPM
-			 * for A7K and on the CPS for A8K.
-			 */
-			compatible = "marvell,armada-8k-nand-controller",
-				"marvell,armada370-nand-controller";
-			reg = <0x720000 0x54>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			interrupts = <115 IRQ_TYPE_LEVEL_HIGH>;
-			clock-names = "core", "reg";
-			clocks = <&CP110_LABEL(clk) 1 2>,
-				 <&CP110_LABEL(clk) 1 17>;
-			marvell,system-controller = <&CP110_LABEL(syscon0)>;
-			status = "disabled";
-		};
-
-		CP110_LABEL(trng): trng@760000 {
-			compatible = "marvell,armada-8k-rng",
-			"inside-secure,safexcel-eip76";
-			reg = <0x760000 0x7d>;
-			interrupts = <95 IRQ_TYPE_LEVEL_HIGH>;
-			clock-names = "core", "reg";
-			clocks = <&CP110_LABEL(clk) 1 25>,
-				 <&CP110_LABEL(clk) 1 17>;
-			status = "okay";
-		};
-
-		CP110_LABEL(sdhci0): sdhci@780000 {
-			compatible = "marvell,armada-cp110-sdhci";
-			reg = <0x780000 0x300>;
-			interrupts = <27 IRQ_TYPE_LEVEL_HIGH>;
-			clock-names = "core", "axi";
-			clocks = <&CP110_LABEL(clk) 1 4>, <&CP110_LABEL(clk) 1 18>;
-			dma-coherent;
-			status = "disabled";
-		};
-
-		CP110_LABEL(crypto): crypto@800000 {
-			compatible = "inside-secure,safexcel-eip197b";
-			reg = <0x800000 0x200000>;
-			interrupts = <87 IRQ_TYPE_LEVEL_HIGH>,
-				<88 IRQ_TYPE_LEVEL_HIGH>,
-				<89 IRQ_TYPE_LEVEL_HIGH>,
-				<90 IRQ_TYPE_LEVEL_HIGH>,
-				<91 IRQ_TYPE_LEVEL_HIGH>,
-				<92 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "mem", "ring0", "ring1",
-				"ring2", "ring3", "eip";
-			clock-names = "core", "reg";
-			clocks = <&CP110_LABEL(clk) 1 26>,
-				 <&CP110_LABEL(clk) 1 17>;
-			dma-coherent;
-		};
-	};
-
-	CP110_LABEL(pcie0): pcie@CP110_PCIE0_BASE {
-		compatible = "marvell,armada8k-pcie", "snps,dw-pcie";
-		reg = <0 ADDRESSIFY(CP110_PCIE0_BASE) 0 0x10000>,
-		      <0 CP110_PCIEx_CONF_BASE(0) 0 0x80000>;
-		reg-names = "ctrl", "config";
-		#address-cells = <3>;
-		#size-cells = <2>;
-		#interrupt-cells = <1>;
-		device_type = "pci";
-		dma-coherent;
-		msi-parent = <&gic_v2m0>;
-
-		bus-range = <0 0xff>;
-		ranges =
-		/* downstream I/O */
-		<0x81000000 0 CP110_PCIEx_IO_BASE(0) 0  CP110_PCIEx_IO_BASE(0) 0 0x10000
-		/* non-prefetchable memory */
-		0x82000000 0 CP110_PCIEx_MEM_BASE(0) 0  CP110_PCIEx_MEM_BASE(0) 0 0xf00000>;
-		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &CP110_LABEL(icu_nsr) 22 IRQ_TYPE_LEVEL_HIGH>;
-		interrupts = <22 IRQ_TYPE_LEVEL_HIGH>;
-		num-lanes = <1>;
-		clock-names = "core", "reg";
-		clocks = <&CP110_LABEL(clk) 1 13>, <&CP110_LABEL(clk) 1 14>;
-		status = "disabled";
-	};
-
-	CP110_LABEL(pcie1): pcie@CP110_PCIE1_BASE {
-		compatible = "marvell,armada8k-pcie", "snps,dw-pcie";
-		reg = <0 ADDRESSIFY(CP110_PCIE1_BASE) 0 0x10000>,
-		      <0 CP110_PCIEx_CONF_BASE(1) 0 0x80000>;
-		reg-names = "ctrl", "config";
-		#address-cells = <3>;
-		#size-cells = <2>;
-		#interrupt-cells = <1>;
-		device_type = "pci";
-		dma-coherent;
-		msi-parent = <&gic_v2m0>;
-
-		bus-range = <0 0xff>;
-		ranges =
-		/* downstream I/O */
-		<0x81000000 0 CP110_PCIEx_IO_BASE(1) 0  CP110_PCIEx_IO_BASE(1) 0 0x10000
-		/* non-prefetchable memory */
-		0x82000000 0 CP110_PCIEx_MEM_BASE(1) 0  CP110_PCIEx_MEM_BASE(1) 0 0xf00000>;
-		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &CP110_LABEL(icu_nsr) 24 IRQ_TYPE_LEVEL_HIGH>;
-		interrupts = <24 IRQ_TYPE_LEVEL_HIGH>;
-
-		num-lanes = <1>;
-		clock-names = "core", "reg";
-		clocks = <&CP110_LABEL(clk) 1 11>, <&CP110_LABEL(clk) 1 14>;
-		status = "disabled";
-	};
-
-	CP110_LABEL(pcie2): pcie@CP110_PCIE2_BASE {
-		compatible = "marvell,armada8k-pcie", "snps,dw-pcie";
-		reg = <0 ADDRESSIFY(CP110_PCIE2_BASE) 0 0x10000>,
-		      <0 CP110_PCIEx_CONF_BASE(2) 0 0x80000>;
-		reg-names = "ctrl", "config";
-		#address-cells = <3>;
-		#size-cells = <2>;
-		#interrupt-cells = <1>;
-		device_type = "pci";
-		dma-coherent;
-		msi-parent = <&gic_v2m0>;
-
-		bus-range = <0 0xff>;
-		ranges =
-		/* downstream I/O */
-		<0x81000000 0 CP110_PCIEx_IO_BASE(2) 0  CP110_PCIEx_IO_BASE(2) 0 0x10000
-		/* non-prefetchable memory */
-		0x82000000 0 CP110_PCIEx_MEM_BASE(2) 0  CP110_PCIEx_MEM_BASE(2) 0 0xf00000>;
-		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &CP110_LABEL(icu_nsr) 23 IRQ_TYPE_LEVEL_HIGH>;
-		interrupts = <23 IRQ_TYPE_LEVEL_HIGH>;
-
-		num-lanes = <1>;
-		clock-names = "core", "reg";
-		clocks = <&CP110_LABEL(clk) 1 12>, <&CP110_LABEL(clk) 1 14>;
-		status = "disabled";
-	};
-};
+#undef CP11X_TYPE
diff --git a/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi b/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
new file mode 100644
index 000000000000..3e77cf34604c
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
@@ -0,0 +1,579 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2016 Marvell Technology Group Ltd.
+ *
+ * Device Tree file for Marvell Armada CP11x.
+ */
+
+#include <dt-bindings/interrupt-controller/mvebu-icu.h>
+#include <dt-bindings/thermal/thermal.h>
+
+#include "armada-common.dtsi"
+
+#define CP11X_PCIEx_IO_BASE(iface)	(CP11X_PCIE_IO_BASE + (iface *  0x10000))
+#define CP11X_PCIEx_MEM_BASE(iface)	(CP11X_PCIE_MEM_BASE + (iface *  0x1000000))
+#define CP11X_PCIEx_CONF_BASE(iface)	(CP11X_PCIEx_MEM_BASE(iface) + 0xf00000)
+
+/ {
+	/*
+	 * The contents of the node are defined below, in order to
+	 * save one indentation level
+	 */
+	CP11X_NAME: CP11X_NAME { };
+
+	/*
+	 * CPs only have one sensor in the thermal IC.
+	 *
+	 * The cooling maps are empty as there are no cooling devices.
+	 */
+	thermal-zones {
+		CP11X_LABEL(thermal_ic): CP11X_NODE_NAME(thermal-ic) {
+			polling-delay-passive = <0>; /* Interrupt driven */
+			polling-delay = <0>; /* Interrupt driven */
+
+			thermal-sensors = <&CP11X_LABEL(thermal) 0>;
+
+			trips {
+				CP11X_LABEL(crit): crit {
+					temperature = <100000>; /* mC degrees */
+					hysteresis = <2000>; /* mC degrees */
+					type = "critical";
+				};
+			};
+
+			cooling-maps { };
+		};
+	};
+};
+
+&CP11X_NAME {
+	#address-cells = <2>;
+	#size-cells = <2>;
+	compatible = "simple-bus";
+	interrupt-parent = <&CP11X_LABEL(icu_nsr)>;
+	ranges;
+
+	config-space@CP11X_BASE {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		ranges = <0x0 0x0 ADDRESSIFY(CP11X_BASE) 0x2000000>;
+
+		CP11X_LABEL(ethernet): ethernet@0 {
+			compatible = "marvell,armada-7k-pp22";
+			reg = <0x0 0x100000>, <0x129000 0xb000>;
+			clocks = <&CP11X_LABEL(clk) 1 3>, <&CP11X_LABEL(clk) 1 9>,
+				 <&CP11X_LABEL(clk) 1 5>, <&CP11X_LABEL(clk) 1 6>,
+				 <&CP11X_LABEL(clk) 1 18>;
+			clock-names = "pp_clk", "gop_clk",
+				      "mg_clk", "mg_core_clk", "axi_clk";
+			marvell,system-controller = <&CP11X_LABEL(syscon0)>;
+			status = "disabled";
+			dma-coherent;
+
+			CP11X_LABEL(eth0): eth0 {
+				interrupts = <39 IRQ_TYPE_LEVEL_HIGH>,
+					<43 IRQ_TYPE_LEVEL_HIGH>,
+					<47 IRQ_TYPE_LEVEL_HIGH>,
+					<51 IRQ_TYPE_LEVEL_HIGH>,
+					<55 IRQ_TYPE_LEVEL_HIGH>,
+					<59 IRQ_TYPE_LEVEL_HIGH>,
+					<63 IRQ_TYPE_LEVEL_HIGH>,
+					<67 IRQ_TYPE_LEVEL_HIGH>,
+					<71 IRQ_TYPE_LEVEL_HIGH>,
+					<129 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "hif0", "hif1", "hif2",
+					"hif3", "hif4", "hif5", "hif6", "hif7",
+					"hif8", "link";
+				port-id = <0>;
+				gop-port-id = <0>;
+				status = "disabled";
+			};
+
+			CP11X_LABEL(eth1): eth1 {
+				interrupts = <40 IRQ_TYPE_LEVEL_HIGH>,
+					<44 IRQ_TYPE_LEVEL_HIGH>,
+					<48 IRQ_TYPE_LEVEL_HIGH>,
+					<52 IRQ_TYPE_LEVEL_HIGH>,
+					<56 IRQ_TYPE_LEVEL_HIGH>,
+					<60 IRQ_TYPE_LEVEL_HIGH>,
+					<64 IRQ_TYPE_LEVEL_HIGH>,
+					<68 IRQ_TYPE_LEVEL_HIGH>,
+					<72 IRQ_TYPE_LEVEL_HIGH>,
+					<128 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "hif0", "hif1", "hif2",
+					"hif3", "hif4", "hif5", "hif6", "hif7",
+					"hif8", "link";
+				port-id = <1>;
+				gop-port-id = <2>;
+				status = "disabled";
+			};
+
+			CP11X_LABEL(eth2): eth2 {
+				interrupts = <41 IRQ_TYPE_LEVEL_HIGH>,
+					<45 IRQ_TYPE_LEVEL_HIGH>,
+					<49 IRQ_TYPE_LEVEL_HIGH>,
+					<53 IRQ_TYPE_LEVEL_HIGH>,
+					<57 IRQ_TYPE_LEVEL_HIGH>,
+					<61 IRQ_TYPE_LEVEL_HIGH>,
+					<65 IRQ_TYPE_LEVEL_HIGH>,
+					<69 IRQ_TYPE_LEVEL_HIGH>,
+					<73 IRQ_TYPE_LEVEL_HIGH>,
+					<127 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "hif0", "hif1", "hif2",
+					"hif3", "hif4", "hif5", "hif6", "hif7",
+					"hif8", "link";
+				port-id = <2>;
+				gop-port-id = <3>;
+				status = "disabled";
+			};
+		};
+
+		CP11X_LABEL(comphy): phy@120000 {
+			compatible = "marvell,comphy-cp110";
+			reg = <0x120000 0x6000>;
+			marvell,system-controller = <&CP11X_LABEL(syscon0)>;
+			clocks = <&CP11X_LABEL(clk) 1 5>, <&CP11X_LABEL(clk) 1 6>,
+				 <&CP11X_LABEL(clk) 1 18>;
+			clock-names = "mg_clk", "mg_core_clk", "axi_clk";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			CP11X_LABEL(comphy0): phy@0 {
+				reg = <0>;
+				#phy-cells = <1>;
+			};
+
+			CP11X_LABEL(comphy1): phy@1 {
+				reg = <1>;
+				#phy-cells = <1>;
+			};
+
+			CP11X_LABEL(comphy2): phy@2 {
+				reg = <2>;
+				#phy-cells = <1>;
+			};
+
+			CP11X_LABEL(comphy3): phy@3 {
+				reg = <3>;
+				#phy-cells = <1>;
+			};
+
+			CP11X_LABEL(comphy4): phy@4 {
+				reg = <4>;
+				#phy-cells = <1>;
+			};
+
+			CP11X_LABEL(comphy5): phy@5 {
+				reg = <5>;
+				#phy-cells = <1>;
+			};
+		};
+
+		CP11X_LABEL(mdio): mdio@12a200 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "marvell,orion-mdio";
+			reg = <0x12a200 0x10>;
+			clocks = <&CP11X_LABEL(clk) 1 9>, <&CP11X_LABEL(clk) 1 5>,
+				 <&CP11X_LABEL(clk) 1 6>, <&CP11X_LABEL(clk) 1 18>;
+			status = "disabled";
+		};
+
+		CP11X_LABEL(xmdio): mdio@12a600 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "marvell,xmdio";
+			reg = <0x12a600 0x10>;
+			clocks = <&CP11X_LABEL(clk) 1 5>,
+				 <&CP11X_LABEL(clk) 1 6>, <&CP11X_LABEL(clk) 1 18>;
+			status = "disabled";
+		};
+
+		CP11X_LABEL(icu): interrupt-controller@1e0000 {
+			compatible = "marvell,cp110-icu";
+			reg = <0x1e0000 0x440>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			CP11X_LABEL(icu_nsr): interrupt-controller@10 {
+				compatible = "marvell,cp110-icu-nsr";
+				reg = <0x10 0x20>;
+				#interrupt-cells = <2>;
+				interrupt-controller;
+				msi-parent = <&gicp>;
+			};
+
+			CP11X_LABEL(icu_sei): interrupt-controller@50 {
+				compatible = "marvell,cp110-icu-sei";
+				reg = <0x50 0x10>;
+				#interrupt-cells = <2>;
+				interrupt-controller;
+				msi-parent = <&sei>;
+			};
+		};
+
+		CP11X_LABEL(rtc): rtc@284000 {
+			compatible = "marvell,armada-8k-rtc";
+			reg = <0x284000 0x20>, <0x284080 0x24>;
+			reg-names = "rtc", "rtc-soc";
+			interrupts = <77 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		CP11X_LABEL(syscon0): system-controller@440000 {
+			compatible = "syscon", "simple-mfd";
+			reg = <0x440000 0x2000>;
+
+			CP11X_LABEL(clk): clock {
+				compatible = "marvell,cp110-clock";
+				#clock-cells = <2>;
+			};
+
+			CP11X_LABEL(gpio1): gpio@100 {
+				compatible = "marvell,armada-8k-gpio";
+				offset = <0x100>;
+				ngpios = <32>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				gpio-ranges = <&CP11X_LABEL(pinctrl) 0 0 32>;
+				interrupt-controller;
+				interrupts = <86 IRQ_TYPE_LEVEL_HIGH>,
+					<85 IRQ_TYPE_LEVEL_HIGH>,
+					<84 IRQ_TYPE_LEVEL_HIGH>,
+					<83 IRQ_TYPE_LEVEL_HIGH>;
+				#interrupt-cells = <2>;
+				status = "disabled";
+			};
+
+			CP11X_LABEL(gpio2): gpio@140 {
+				compatible = "marvell,armada-8k-gpio";
+				offset = <0x140>;
+				ngpios = <31>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				gpio-ranges = <&CP11X_LABEL(pinctrl) 0 32 31>;
+				interrupt-controller;
+				interrupts = <82 IRQ_TYPE_LEVEL_HIGH>,
+					<81 IRQ_TYPE_LEVEL_HIGH>,
+					<80 IRQ_TYPE_LEVEL_HIGH>,
+					<79 IRQ_TYPE_LEVEL_HIGH>;
+				#interrupt-cells = <2>;
+				status = "disabled";
+			};
+		};
+
+		CP11X_LABEL(syscon1): system-controller@400000 {
+			compatible = "syscon", "simple-mfd";
+			reg = <0x400000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			CP11X_LABEL(thermal): thermal-sensor@70 {
+				compatible = "marvell,armada-cp110-thermal";
+				reg = <0x70 0x10>;
+				interrupts-extended =
+					<&CP11X_LABEL(icu_sei) 116 IRQ_TYPE_LEVEL_HIGH>;
+				#thermal-sensor-cells = <1>;
+			};
+		};
+
+		CP11X_LABEL(usb3_0): usb3@500000 {
+			compatible = "marvell,armada-8k-xhci",
+			"generic-xhci";
+			reg = <0x500000 0x4000>;
+			dma-coherent;
+			interrupts = <106 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "core", "reg";
+			clocks = <&CP11X_LABEL(clk) 1 22>,
+				 <&CP11X_LABEL(clk) 1 16>;
+			status = "disabled";
+		};
+
+		CP11X_LABEL(usb3_1): usb3@510000 {
+			compatible = "marvell,armada-8k-xhci",
+			"generic-xhci";
+			reg = <0x510000 0x4000>;
+			dma-coherent;
+			interrupts = <105 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "core", "reg";
+			clocks = <&CP11X_LABEL(clk) 1 23>,
+				 <&CP11X_LABEL(clk) 1 16>;
+			status = "disabled";
+		};
+
+		CP11X_LABEL(sata0): sata@540000 {
+			compatible = "marvell,armada-8k-ahci",
+			"generic-ahci";
+			reg = <0x540000 0x30000>;
+			dma-coherent;
+			interrupts = <107 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&CP11X_LABEL(clk) 1 15>,
+				 <&CP11X_LABEL(clk) 1 16>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sata-port@0 {
+				reg = <0>;
+			};
+
+			sata-port@1 {
+				reg = <1>;
+			};
+		};
+
+		CP11X_LABEL(xor0): xor@6a0000 {
+			compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
+			reg = <0x6a0000 0x1000>, <0x6b0000 0x1000>;
+			dma-coherent;
+			msi-parent = <&gic_v2m0>;
+			clock-names = "core", "reg";
+			clocks = <&CP11X_LABEL(clk) 1 8>,
+				 <&CP11X_LABEL(clk) 1 14>;
+		};
+
+		CP11X_LABEL(xor1): xor@6c0000 {
+			compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
+			reg = <0x6c0000 0x1000>, <0x6d0000 0x1000>;
+			dma-coherent;
+			msi-parent = <&gic_v2m0>;
+			clock-names = "core", "reg";
+			clocks = <&CP11X_LABEL(clk) 1 7>,
+				 <&CP11X_LABEL(clk) 1 14>;
+		};
+
+		CP11X_LABEL(spi0): spi@700600 {
+			compatible = "marvell,armada-380-spi";
+			reg = <0x700600 0x50>;
+			#address-cells = <0x1>;
+			#size-cells = <0x0>;
+			clock-names = "core", "axi";
+			clocks = <&CP11X_LABEL(clk) 1 21>,
+				 <&CP11X_LABEL(clk) 1 17>;
+			status = "disabled";
+		};
+
+		CP11X_LABEL(spi1): spi@700680 {
+			compatible = "marvell,armada-380-spi";
+			reg = <0x700680 0x50>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clock-names = "core", "axi";
+			clocks = <&CP11X_LABEL(clk) 1 21>,
+				 <&CP11X_LABEL(clk) 1 17>;
+			status = "disabled";
+		};
+
+		CP11X_LABEL(i2c0): i2c@701000 {
+			compatible = "marvell,mv78230-i2c";
+			reg = <0x701000 0x20>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <120 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "core", "reg";
+			clocks = <&CP11X_LABEL(clk) 1 21>,
+				 <&CP11X_LABEL(clk) 1 17>;
+			status = "disabled";
+		};
+
+		CP11X_LABEL(i2c1): i2c@701100 {
+			compatible = "marvell,mv78230-i2c";
+			reg = <0x701100 0x20>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <121 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "core", "reg";
+			clocks = <&CP11X_LABEL(clk) 1 21>,
+				 <&CP11X_LABEL(clk) 1 17>;
+			status = "disabled";
+		};
+
+		CP11X_LABEL(uart0): serial@702000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x702000 0x100>;
+			reg-shift = <2>;
+			interrupts = <122 IRQ_TYPE_LEVEL_HIGH>;
+			reg-io-width = <1>;
+			clock-names = "baudclk", "apb_pclk";
+			clocks = <&CP11X_LABEL(clk) 1 21>,
+				 <&CP11X_LABEL(clk) 1 17>;
+			status = "disabled";
+		};
+
+		CP11X_LABEL(uart1): serial@702100 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x702100 0x100>;
+			reg-shift = <2>;
+			interrupts = <123 IRQ_TYPE_LEVEL_HIGH>;
+			reg-io-width = <1>;
+			clock-names = "baudclk", "apb_pclk";
+			clocks = <&CP11X_LABEL(clk) 1 21>,
+				 <&CP11X_LABEL(clk) 1 17>;
+			status = "disabled";
+		};
+
+		CP11X_LABEL(uart2): serial@702200 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x702200 0x100>;
+			reg-shift = <2>;
+			interrupts = <124 IRQ_TYPE_LEVEL_HIGH>;
+			reg-io-width = <1>;
+			clock-names = "baudclk", "apb_pclk";
+			clocks = <&CP11X_LABEL(clk) 1 21>,
+				 <&CP11X_LABEL(clk) 1 17>;
+			status = "disabled";
+		};
+
+		CP11X_LABEL(uart3): serial@702300 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x702300 0x100>;
+			reg-shift = <2>;
+			interrupts = <125 IRQ_TYPE_LEVEL_HIGH>;
+			reg-io-width = <1>;
+			clock-names = "baudclk", "apb_pclk";
+			clocks = <&CP11X_LABEL(clk) 1 21>,
+				 <&CP11X_LABEL(clk) 1 17>;
+			status = "disabled";
+		};
+
+		CP11X_LABEL(nand_controller): nand@720000 {
+			/*
+			 * Due to the limitation of the pins available
+			 * this controller is only usable on the CPM
+			 * for A7K and on the CPS for A8K.
+			 */
+			compatible = "marvell,armada-8k-nand-controller",
+				"marvell,armada370-nand-controller";
+			reg = <0x720000 0x54>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <115 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "core", "reg";
+			clocks = <&CP11X_LABEL(clk) 1 2>,
+				 <&CP11X_LABEL(clk) 1 17>;
+			marvell,system-controller = <&CP11X_LABEL(syscon0)>;
+			status = "disabled";
+		};
+
+		CP11X_LABEL(trng): trng@760000 {
+			compatible = "marvell,armada-8k-rng",
+			"inside-secure,safexcel-eip76";
+			reg = <0x760000 0x7d>;
+			interrupts = <95 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "core", "reg";
+			clocks = <&CP11X_LABEL(clk) 1 25>,
+				 <&CP11X_LABEL(clk) 1 17>;
+			status = "okay";
+		};
+
+		CP11X_LABEL(sdhci0): sdhci@780000 {
+			compatible = "marvell,armada-cp110-sdhci";
+			reg = <0x780000 0x300>;
+			interrupts = <27 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "core", "axi";
+			clocks = <&CP11X_LABEL(clk) 1 4>, <&CP11X_LABEL(clk) 1 18>;
+			dma-coherent;
+			status = "disabled";
+		};
+
+		CP11X_LABEL(crypto): crypto@800000 {
+			compatible = "inside-secure,safexcel-eip197b";
+			reg = <0x800000 0x200000>;
+			interrupts = <87 IRQ_TYPE_LEVEL_HIGH>,
+				<88 IRQ_TYPE_LEVEL_HIGH>,
+				<89 IRQ_TYPE_LEVEL_HIGH>,
+				<90 IRQ_TYPE_LEVEL_HIGH>,
+				<91 IRQ_TYPE_LEVEL_HIGH>,
+				<92 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "mem", "ring0", "ring1",
+				"ring2", "ring3", "eip";
+			clock-names = "core", "reg";
+			clocks = <&CP11X_LABEL(clk) 1 26>,
+				 <&CP11X_LABEL(clk) 1 17>;
+			dma-coherent;
+		};
+	};
+
+	CP11X_LABEL(pcie0): pcie@CP11X_PCIE0_BASE {
+		compatible = "marvell,armada8k-pcie", "snps,dw-pcie";
+		reg = <0 ADDRESSIFY(CP11X_PCIE0_BASE) 0 0x10000>,
+		      <0 CP11X_PCIEx_CONF_BASE(0) 0 0x80000>;
+		reg-names = "ctrl", "config";
+		#address-cells = <3>;
+		#size-cells = <2>;
+		#interrupt-cells = <1>;
+		device_type = "pci";
+		dma-coherent;
+		msi-parent = <&gic_v2m0>;
+
+		bus-range = <0 0xff>;
+		ranges =
+		/* downstream I/O */
+		<0x81000000 0 CP11X_PCIEx_IO_BASE(0) 0  CP11X_PCIEx_IO_BASE(0) 0 0x10000
+		/* non-prefetchable memory */
+		0x82000000 0 CP11X_PCIEx_MEM_BASE(0) 0  CP11X_PCIEx_MEM_BASE(0) 0 0xf00000>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &CP11X_LABEL(icu_nsr) 22 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <22 IRQ_TYPE_LEVEL_HIGH>;
+		num-lanes = <1>;
+		clock-names = "core", "reg";
+		clocks = <&CP11X_LABEL(clk) 1 13>, <&CP11X_LABEL(clk) 1 14>;
+		status = "disabled";
+	};
+
+	CP11X_LABEL(pcie1): pcie@CP11X_PCIE1_BASE {
+		compatible = "marvell,armada8k-pcie", "snps,dw-pcie";
+		reg = <0 ADDRESSIFY(CP11X_PCIE1_BASE) 0 0x10000>,
+		      <0 CP11X_PCIEx_CONF_BASE(1) 0 0x80000>;
+		reg-names = "ctrl", "config";
+		#address-cells = <3>;
+		#size-cells = <2>;
+		#interrupt-cells = <1>;
+		device_type = "pci";
+		dma-coherent;
+		msi-parent = <&gic_v2m0>;
+
+		bus-range = <0 0xff>;
+		ranges =
+		/* downstream I/O */
+		<0x81000000 0 CP11X_PCIEx_IO_BASE(1) 0  CP11X_PCIEx_IO_BASE(1) 0 0x10000
+		/* non-prefetchable memory */
+		0x82000000 0 CP11X_PCIEx_MEM_BASE(1) 0  CP11X_PCIEx_MEM_BASE(1) 0 0xf00000>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &CP11X_LABEL(icu_nsr) 24 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <24 IRQ_TYPE_LEVEL_HIGH>;
+
+		num-lanes = <1>;
+		clock-names = "core", "reg";
+		clocks = <&CP11X_LABEL(clk) 1 11>, <&CP11X_LABEL(clk) 1 14>;
+		status = "disabled";
+	};
+
+	CP11X_LABEL(pcie2): pcie@CP11X_PCIE2_BASE {
+		compatible = "marvell,armada8k-pcie", "snps,dw-pcie";
+		reg = <0 ADDRESSIFY(CP11X_PCIE2_BASE) 0 0x10000>,
+		      <0 CP11X_PCIEx_CONF_BASE(2) 0 0x80000>;
+		reg-names = "ctrl", "config";
+		#address-cells = <3>;
+		#size-cells = <2>;
+		#interrupt-cells = <1>;
+		device_type = "pci";
+		dma-coherent;
+		msi-parent = <&gic_v2m0>;
+
+		bus-range = <0 0xff>;
+		ranges =
+		/* downstream I/O */
+		<0x81000000 0 CP11X_PCIEx_IO_BASE(2) 0  CP11X_PCIEx_IO_BASE(2) 0 0x10000
+		/* non-prefetchable memory */
+		0x82000000 0 CP11X_PCIEx_MEM_BASE(2) 0  CP11X_PCIEx_MEM_BASE(2) 0 0xf00000>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &CP11X_LABEL(icu_nsr) 23 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <23 IRQ_TYPE_LEVEL_HIGH>;
+
+		num-lanes = <1>;
+		clock-names = "core", "reg";
+		clocks = <&CP11X_LABEL(clk) 1 12>, <&CP11X_LABEL(clk) 1 14>;
+		status = "disabled";
+	};
+};
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 25+ messages in thread

* [PATCH 13/20] arm64: dts: marvell: Drop PCIe I/O ranges from CP11x file
  2019-08-06 14:54 [PATCH 00/20] Add new Marvell CN9130 SoC support Miquel Raynal
                   ` (11 preceding siblings ...)
  2019-08-06 14:54 ` [PATCH 12/20] arm64: dts: marvell: Prepare the introduction of CP115 Miquel Raynal
@ 2019-08-06 14:54 ` Miquel Raynal
  2019-08-06 14:54 ` [PATCH 14/20] arm64: dts: marvell: Externalize PCIe macros " Miquel Raynal
                   ` (6 subsequent siblings)
  19 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-08-06 14:54 UTC (permalink / raw)
  To: Rob Herring, Mark Rutland
  Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
	Gregory Clement, Maxime Chevallier, Nadav Haklai,
	Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
	linux-arm-kernel

As an example, Armada 70x0 and 80x0 SoC 0xf9000000 region points to
RUNIT/SPICS0 while it is referenced in the DT as PCIe I/O memory
range. This shows that I/O memory has never been used/working on the
old SoCs despite the region being advertised. As PCIe I/O ranges will
not be supported in newer SoCs using CP11x co-processors, let's
simply drop them. It is not harmful in any case as PCIe device drivers
can do it all with the regular mapped memory anyway.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 arch/arm64/boot/dts/marvell/armada-70x0.dtsi     |  2 --
 .../boot/dts/marvell/armada-8040-mcbin.dtsi      |  3 +--
 arch/arm64/boot/dts/marvell/armada-80x0.dtsi     |  4 ----
 arch/arm64/boot/dts/marvell/armada-cp11x.dtsi    | 16 +++-------------
 4 files changed, 4 insertions(+), 21 deletions(-)

diff --git a/arch/arm64/boot/dts/marvell/armada-70x0.dtsi b/arch/arm64/boot/dts/marvell/armada-70x0.dtsi
index 4e78ccd207b7..ac28903ea409 100644
--- a/arch/arm64/boot/dts/marvell/armada-70x0.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-70x0.dtsi
@@ -19,7 +19,6 @@
  */
 #define CP11X_NAME		cp0
 #define CP11X_BASE		f2000000
-#define CP11X_PCIE_IO_BASE	0xf9000000
 #define CP11X_PCIE_MEM_BASE	0xf6000000
 #define CP11X_PCIE0_BASE	f2600000
 #define CP11X_PCIE1_BASE	f2620000
@@ -29,7 +28,6 @@
 
 #undef CP11X_NAME
 #undef CP11X_BASE
-#undef CP11X_PCIE_IO_BASE
 #undef CP11X_PCIE_MEM_BASE
 #undef CP11X_PCIE0_BASE
 #undef CP11X_PCIE1_BASE
diff --git a/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtsi b/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtsi
index d250f4b2bfed..572e2610e0a3 100644
--- a/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtsi
@@ -179,8 +179,7 @@
 	num-lanes = <4>;
 	num-viewport = <8>;
 	reset-gpios = <&cp0_gpio2 20 GPIO_ACTIVE_LOW>;
-	ranges = <0x81000000 0x0 0xf9010000 0x0 0xf9010000 0x0 0x10000
-		  0x82000000 0x0 0xc0000000 0x0 0xc0000000 0x0 0x20000000>;
+	ranges = <0x82000000 0x0 0xc0000000 0x0 0xc0000000 0x0 0x20000000>;
 	phys = <&cp0_comphy0 0>, <&cp0_comphy1 0>,
 	       <&cp0_comphy2 0>, <&cp0_comphy3 0>;
 	phy-names = "cp0-pcie0-x4-lane0-phy", "cp0-pcie0-x4-lane1-phy",
diff --git a/arch/arm64/boot/dts/marvell/armada-80x0.dtsi b/arch/arm64/boot/dts/marvell/armada-80x0.dtsi
index ebb98836ec9c..902eed571bcc 100644
--- a/arch/arm64/boot/dts/marvell/armada-80x0.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-80x0.dtsi
@@ -21,7 +21,6 @@
  */
 #define CP11X_NAME		cp0
 #define CP11X_BASE		f2000000
-#define CP11X_PCIE_IO_BASE	0xf9000000
 #define CP11X_PCIE_MEM_BASE	0xf6000000
 #define CP11X_PCIE0_BASE	f2600000
 #define CP11X_PCIE1_BASE	f2620000
@@ -31,7 +30,6 @@
 
 #undef CP11X_NAME
 #undef CP11X_BASE
-#undef CP11X_PCIE_IO_BASE
 #undef CP11X_PCIE_MEM_BASE
 #undef CP11X_PCIE0_BASE
 #undef CP11X_PCIE1_BASE
@@ -42,7 +40,6 @@
  */
 #define CP11X_NAME		cp1
 #define CP11X_BASE		f4000000
-#define CP11X_PCIE_IO_BASE	0xfd000000
 #define CP11X_PCIE_MEM_BASE	0xfa000000
 #define CP11X_PCIE0_BASE	f4600000
 #define CP11X_PCIE1_BASE	f4620000
@@ -52,7 +49,6 @@
 
 #undef CP11X_NAME
 #undef CP11X_BASE
-#undef CP11X_PCIE_IO_BASE
 #undef CP11X_PCIE_MEM_BASE
 #undef CP11X_PCIE0_BASE
 #undef CP11X_PCIE1_BASE
diff --git a/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi b/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
index 3e77cf34604c..7d1ab097453d 100644
--- a/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
@@ -10,7 +10,6 @@
 
 #include "armada-common.dtsi"
 
-#define CP11X_PCIEx_IO_BASE(iface)	(CP11X_PCIE_IO_BASE + (iface *  0x10000))
 #define CP11X_PCIEx_MEM_BASE(iface)	(CP11X_PCIE_MEM_BASE + (iface *  0x1000000))
 #define CP11X_PCIEx_CONF_BASE(iface)	(CP11X_PCIEx_MEM_BASE(iface) + 0xf00000)
 
@@ -507,11 +506,8 @@
 		msi-parent = <&gic_v2m0>;
 
 		bus-range = <0 0xff>;
-		ranges =
-		/* downstream I/O */
-		<0x81000000 0 CP11X_PCIEx_IO_BASE(0) 0  CP11X_PCIEx_IO_BASE(0) 0 0x10000
 		/* non-prefetchable memory */
-		0x82000000 0 CP11X_PCIEx_MEM_BASE(0) 0  CP11X_PCIEx_MEM_BASE(0) 0 0xf00000>;
+		ranges = <0x82000000 0 CP11X_PCIEx_MEM_BASE(0) 0  CP11X_PCIEx_MEM_BASE(0) 0 0xf00000>;
 		interrupt-map-mask = <0 0 0 0>;
 		interrupt-map = <0 0 0 0 &CP11X_LABEL(icu_nsr) 22 IRQ_TYPE_LEVEL_HIGH>;
 		interrupts = <22 IRQ_TYPE_LEVEL_HIGH>;
@@ -534,11 +530,8 @@
 		msi-parent = <&gic_v2m0>;
 
 		bus-range = <0 0xff>;
-		ranges =
-		/* downstream I/O */
-		<0x81000000 0 CP11X_PCIEx_IO_BASE(1) 0  CP11X_PCIEx_IO_BASE(1) 0 0x10000
 		/* non-prefetchable memory */
-		0x82000000 0 CP11X_PCIEx_MEM_BASE(1) 0  CP11X_PCIEx_MEM_BASE(1) 0 0xf00000>;
+		ranges = <0x82000000 0 CP11X_PCIEx_MEM_BASE(1) 0  CP11X_PCIEx_MEM_BASE(1) 0 0xf00000>;
 		interrupt-map-mask = <0 0 0 0>;
 		interrupt-map = <0 0 0 0 &CP11X_LABEL(icu_nsr) 24 IRQ_TYPE_LEVEL_HIGH>;
 		interrupts = <24 IRQ_TYPE_LEVEL_HIGH>;
@@ -562,11 +555,8 @@
 		msi-parent = <&gic_v2m0>;
 
 		bus-range = <0 0xff>;
-		ranges =
-		/* downstream I/O */
-		<0x81000000 0 CP11X_PCIEx_IO_BASE(2) 0  CP11X_PCIEx_IO_BASE(2) 0 0x10000
 		/* non-prefetchable memory */
-		0x82000000 0 CP11X_PCIEx_MEM_BASE(2) 0  CP11X_PCIEx_MEM_BASE(2) 0 0xf00000>;
+		ranges = <0x82000000 0 CP11X_PCIEx_MEM_BASE(2) 0  CP11X_PCIEx_MEM_BASE(2) 0 0xf00000>;
 		interrupt-map-mask = <0 0 0 0>;
 		interrupt-map = <0 0 0 0 &CP11X_LABEL(icu_nsr) 23 IRQ_TYPE_LEVEL_HIGH>;
 		interrupts = <23 IRQ_TYPE_LEVEL_HIGH>;
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 25+ messages in thread

* [PATCH 14/20] arm64: dts: marvell: Externalize PCIe macros from CP11x file
  2019-08-06 14:54 [PATCH 00/20] Add new Marvell CN9130 SoC support Miquel Raynal
                   ` (12 preceding siblings ...)
  2019-08-06 14:54 ` [PATCH 13/20] arm64: dts: marvell: Drop PCIe I/O ranges from CP11x file Miquel Raynal
@ 2019-08-06 14:54 ` " Miquel Raynal
  2019-08-06 14:54 ` [PATCH 15/20] arm64: dts: marvell: Add support for CP115 Miquel Raynal
                   ` (5 subsequent siblings)
  19 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-08-06 14:54 UTC (permalink / raw)
  To: Rob Herring, Mark Rutland
  Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
	Gregory Clement, Maxime Chevallier, Nadav Haklai,
	Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
	linux-arm-kernel

PCIe macros are specific to CP110 and will not fit CP115
constraints. To keep the same way the files are organized, just move
some macros out of the CP11x generic file and define them directly in
SoC DTSI, instead of defining single addresses in the SoC DTSI and
reusing them in macros.

In the end:
* CP11X_PCIE_MEM_BASE SoC define is dropped
* CP11X_PCIEx_MEM_BASE is moved out of the generic DT to be put in the
  SoC files as it replaces the above definition.
* As the CP11X_PCIEx_MEM_SIZE macro is also subject to change with
  newer SoCs, we put it in the SoC files as well.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 arch/arm64/boot/dts/marvell/armada-70x0.dtsi  |  6 ++++--
 arch/arm64/boot/dts/marvell/armada-80x0.dtsi  | 12 ++++++++----
 arch/arm64/boot/dts/marvell/armada-cp11x.dtsi |  9 ++++-----
 3 files changed, 16 insertions(+), 11 deletions(-)

diff --git a/arch/arm64/boot/dts/marvell/armada-70x0.dtsi b/arch/arm64/boot/dts/marvell/armada-70x0.dtsi
index ac28903ea409..293403a1a333 100644
--- a/arch/arm64/boot/dts/marvell/armada-70x0.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-70x0.dtsi
@@ -19,7 +19,8 @@
  */
 #define CP11X_NAME		cp0
 #define CP11X_BASE		f2000000
-#define CP11X_PCIE_MEM_BASE	0xf6000000
+#define CP11X_PCIEx_MEM_BASE(iface) (0xf6000000 + (iface * 0x1000000))
+#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000
 #define CP11X_PCIE0_BASE	f2600000
 #define CP11X_PCIE1_BASE	f2620000
 #define CP11X_PCIE2_BASE	f2640000
@@ -28,7 +29,8 @@
 
 #undef CP11X_NAME
 #undef CP11X_BASE
-#undef CP11X_PCIE_MEM_BASE
+#undef CP11X_PCIEx_MEM_BASE
+#undef CP11X_PCIEx_MEM_SIZE
 #undef CP11X_PCIE0_BASE
 #undef CP11X_PCIE1_BASE
 #undef CP11X_PCIE2_BASE
diff --git a/arch/arm64/boot/dts/marvell/armada-80x0.dtsi b/arch/arm64/boot/dts/marvell/armada-80x0.dtsi
index 902eed571bcc..ee67c70bf02e 100644
--- a/arch/arm64/boot/dts/marvell/armada-80x0.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-80x0.dtsi
@@ -21,7 +21,8 @@
  */
 #define CP11X_NAME		cp0
 #define CP11X_BASE		f2000000
-#define CP11X_PCIE_MEM_BASE	0xf6000000
+#define CP11X_PCIEx_MEM_BASE(iface) (0xf6000000 + (iface * 0x1000000))
+#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000
 #define CP11X_PCIE0_BASE	f2600000
 #define CP11X_PCIE1_BASE	f2620000
 #define CP11X_PCIE2_BASE	f2640000
@@ -30,7 +31,8 @@
 
 #undef CP11X_NAME
 #undef CP11X_BASE
-#undef CP11X_PCIE_MEM_BASE
+#undef CP11X_PCIEx_MEM_BASE
+#undef CP11X_PCIEx_MEM_SIZE
 #undef CP11X_PCIE0_BASE
 #undef CP11X_PCIE1_BASE
 #undef CP11X_PCIE2_BASE
@@ -40,7 +42,8 @@
  */
 #define CP11X_NAME		cp1
 #define CP11X_BASE		f4000000
-#define CP11X_PCIE_MEM_BASE	0xfa000000
+#define CP11X_PCIEx_MEM_BASE(iface) (0xfa000000 + (iface * 0x1000000))
+#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000
 #define CP11X_PCIE0_BASE	f4600000
 #define CP11X_PCIE1_BASE	f4620000
 #define CP11X_PCIE2_BASE	f4640000
@@ -49,7 +52,8 @@
 
 #undef CP11X_NAME
 #undef CP11X_BASE
-#undef CP11X_PCIE_MEM_BASE
+#undef CP11X_PCIEx_MEM_BASE
+#undef CP11X_PCIEx_MEM_SIZE
 #undef CP11X_PCIE0_BASE
 #undef CP11X_PCIE1_BASE
 #undef CP11X_PCIE2_BASE
diff --git a/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi b/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
index 7d1ab097453d..9dcf16beabf5 100644
--- a/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
@@ -10,8 +10,7 @@
 
 #include "armada-common.dtsi"
 
-#define CP11X_PCIEx_MEM_BASE(iface)	(CP11X_PCIE_MEM_BASE + (iface *  0x1000000))
-#define CP11X_PCIEx_CONF_BASE(iface)	(CP11X_PCIEx_MEM_BASE(iface) + 0xf00000)
+#define CP11X_PCIEx_CONF_BASE(iface)	(CP11X_PCIEx_MEM_BASE(iface) + CP11X_PCIEx_MEM_SIZE(iface))
 
 / {
 	/*
@@ -507,7 +506,7 @@
 
 		bus-range = <0 0xff>;
 		/* non-prefetchable memory */
-		ranges = <0x82000000 0 CP11X_PCIEx_MEM_BASE(0) 0  CP11X_PCIEx_MEM_BASE(0) 0 0xf00000>;
+		ranges = <0x82000000 0 CP11X_PCIEx_MEM_BASE(0) 0  CP11X_PCIEx_MEM_BASE(0) 0 CP11X_PCIEx_MEM_SIZE(0)>;
 		interrupt-map-mask = <0 0 0 0>;
 		interrupt-map = <0 0 0 0 &CP11X_LABEL(icu_nsr) 22 IRQ_TYPE_LEVEL_HIGH>;
 		interrupts = <22 IRQ_TYPE_LEVEL_HIGH>;
@@ -531,7 +530,7 @@
 
 		bus-range = <0 0xff>;
 		/* non-prefetchable memory */
-		ranges = <0x82000000 0 CP11X_PCIEx_MEM_BASE(1) 0  CP11X_PCIEx_MEM_BASE(1) 0 0xf00000>;
+		ranges = <0x82000000 0 CP11X_PCIEx_MEM_BASE(1) 0  CP11X_PCIEx_MEM_BASE(1) 0 CP11X_PCIEx_MEM_SIZE(1)>;
 		interrupt-map-mask = <0 0 0 0>;
 		interrupt-map = <0 0 0 0 &CP11X_LABEL(icu_nsr) 24 IRQ_TYPE_LEVEL_HIGH>;
 		interrupts = <24 IRQ_TYPE_LEVEL_HIGH>;
@@ -556,7 +555,7 @@
 
 		bus-range = <0 0xff>;
 		/* non-prefetchable memory */
-		ranges = <0x82000000 0 CP11X_PCIEx_MEM_BASE(2) 0  CP11X_PCIEx_MEM_BASE(2) 0 0xf00000>;
+		ranges = <0x82000000 0 CP11X_PCIEx_MEM_BASE(2) 0  CP11X_PCIEx_MEM_BASE(2) 0 CP11X_PCIEx_MEM_SIZE(2)>;
 		interrupt-map-mask = <0 0 0 0>;
 		interrupt-map = <0 0 0 0 &CP11X_LABEL(icu_nsr) 23 IRQ_TYPE_LEVEL_HIGH>;
 		interrupts = <23 IRQ_TYPE_LEVEL_HIGH>;
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 25+ messages in thread

* [PATCH 15/20] arm64: dts: marvell: Add support for CP115
  2019-08-06 14:54 [PATCH 00/20] Add new Marvell CN9130 SoC support Miquel Raynal
                   ` (13 preceding siblings ...)
  2019-08-06 14:54 ` [PATCH 14/20] arm64: dts: marvell: Externalize PCIe macros " Miquel Raynal
@ 2019-08-06 14:54 ` Miquel Raynal
  2019-08-06 14:54 ` [PATCH 16/20] dt-bindings: marvell: Declare the CN913x SoC compatibles Miquel Raynal
                   ` (4 subsequent siblings)
  19 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-08-06 14:54 UTC (permalink / raw)
  To: Rob Herring, Mark Rutland
  Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
	Gregory Clement, Maxime Chevallier, Nadav Haklai,
	Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
	linux-arm-kernel

Create a DTSI file based on the CP11x one. Differences will be
described in the near future.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 arch/arm64/boot/dts/marvell/armada-cp115.dtsi | 12 ++++++++++++
 1 file changed, 12 insertions(+)
 create mode 100644 arch/arm64/boot/dts/marvell/armada-cp115.dtsi

diff --git a/arch/arm64/boot/dts/marvell/armada-cp115.dtsi b/arch/arm64/boot/dts/marvell/armada-cp115.dtsi
new file mode 100644
index 000000000000..1d0a9653e681
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/armada-cp115.dtsi
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Marvell Technology Group Ltd.
+ *
+ * Device Tree file for Marvell Armada CP115.
+ */
+
+#define CP11X_TYPE cp115
+
+#include "armada-cp11x.dtsi"
+
+#undef CP11X_TYPE
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 25+ messages in thread

* [PATCH 16/20] dt-bindings: marvell: Declare the CN913x SoC compatibles
  2019-08-06 14:54 [PATCH 00/20] Add new Marvell CN9130 SoC support Miquel Raynal
                   ` (14 preceding siblings ...)
  2019-08-06 14:54 ` [PATCH 15/20] arm64: dts: marvell: Add support for CP115 Miquel Raynal
@ 2019-08-06 14:54 ` Miquel Raynal
  2019-08-21 19:37   ` Rob Herring
  2019-08-06 14:54 ` [PATCH 17/20] arm64: dts: marvell: Add support for Marvell CN9130 SoC support Miquel Raynal
                   ` (3 subsequent siblings)
  19 siblings, 1 reply; 25+ messages in thread
From: Miquel Raynal @ 2019-08-06 14:54 UTC (permalink / raw)
  To: Rob Herring, Mark Rutland
  Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
	Gregory Clement, Maxime Chevallier, Nadav Haklai,
	Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
	linux-arm-kernel

From: Grzegorz Jaszczyk <jaz@semihalf.com>

Describe the compatible properties for the new Marvell SoCs:
* CN9130: 1x AP807-quad + 1x CP115 (1x embedded)
* CN9131: 1x AP807-quad + 2x CP115 (1x embedded + 1x modular)
* CN9132: 1x AP807-quad + 3x CP115 (1x embedded + 2x modular)

CP115 are similar to CP110 in terms of features.

There are three development boards based on these SoCs:
* CN9130-DB: comes as a single mother board (with the CP115 bundled)
* CN9131-DB: same as CN9130-DB with one additional modular CP115
* CN9132-DB: same as CN9130-DB with two additional modular CP115

Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 .../bindings/arm/marvell/armada-7k-8k.txt           | 13 ++++++++++++-
 1 file changed, 12 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.txt b/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.txt
index df98a9c82a8c..8eb34ca4c4f0 100644
--- a/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.txt
+++ b/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.txt
@@ -1,7 +1,7 @@
 Marvell Armada 7K/8K Platforms Device Tree Bindings
 ---------------------------------------------------
 
-Boards using a SoC of the Marvell Armada 7K or 8K families must carry
+Boards using a SoC of the Marvell Armada 7K/8K or CN913x families must carry
 the following root node property:
 
  - compatible, with one of the following values:
@@ -18,6 +18,17 @@ the following root node property:
    - "marvell,armada8040", "marvell,armada-ap806-quad", "marvell,armada-ap806"
       when the SoC being used is the Armada 8040
 
+   - "marvell,cn9130", "marvell,armada-ap807-quad", "marvell,armada-ap807"
+      when the SoC being used is the Armada CN9130 with no external CP.
+
+   - "marvell,cn9131", "marvell,cn9130",
+     "marvell,armada-ap807-quad", "marvell,armada-ap807"
+      when the SoC being used is the Armada CN9130 with one external CP.
+
+   - "marvell,cn9132", "marvell,cn9131", "marvell,cn9130",
+     "marvell,armada-ap807-quad", "marvell,armada-ap807"
+      when the SoC being used is the Armada CN9130 with two external CPs.
+
 Example:
 
 compatible = "marvell,armada7040-db", "marvell,armada7040",
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 25+ messages in thread

* [PATCH 17/20] arm64: dts: marvell: Add support for Marvell CN9130 SoC support
  2019-08-06 14:54 [PATCH 00/20] Add new Marvell CN9130 SoC support Miquel Raynal
                   ` (15 preceding siblings ...)
  2019-08-06 14:54 ` [PATCH 16/20] dt-bindings: marvell: Declare the CN913x SoC compatibles Miquel Raynal
@ 2019-08-06 14:54 ` Miquel Raynal
  2019-08-06 14:54 ` [PATCH 18/20] arm64: dts: marvell: Add support for Marvell CN9130-DB Miquel Raynal
                   ` (2 subsequent siblings)
  19 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-08-06 14:54 UTC (permalink / raw)
  To: Rob Herring, Mark Rutland
  Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
	Gregory Clement, Maxime Chevallier, Nadav Haklai,
	Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
	linux-arm-kernel

A CN9130 SoC has one AP807 and one internal CP115.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 arch/arm64/boot/dts/marvell/cn9130.dtsi | 37 +++++++++++++++++++++++++
 1 file changed, 37 insertions(+)
 create mode 100644 arch/arm64/boot/dts/marvell/cn9130.dtsi

diff --git a/arch/arm64/boot/dts/marvell/cn9130.dtsi b/arch/arm64/boot/dts/marvell/cn9130.dtsi
new file mode 100644
index 000000000000..a2b7e5ec979d
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/cn9130.dtsi
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Marvell International Ltd.
+ *
+ * Device tree for the CN9130 SoC.
+ */
+
+#include "armada-ap807-quad.dtsi"
+
+/ {
+	model = "Marvell Armada CN9130 SoC";
+	compatible = "marvell,cn9130", "marvell,armada-ap807-quad",
+		     "marvell,armada-ap807";
+};
+
+/*
+ * Instantiate the internal CP115
+ */
+
+#define CP11X_NAME		cp0
+#define CP11X_BASE		f2000000
+#define CP11X_PCIEx_MEM_BASE(iface) ((iface == 0) ? 0xc0000000 : \
+						    0xe0000000 + ((iface - 1) * 0x1000000))
+#define CP11X_PCIEx_MEM_SIZE(iface) ((iface == 0) ? 0x1ff00000 : 0xf00000)
+#define CP11X_PCIE0_BASE	f2600000
+#define CP11X_PCIE1_BASE	f2620000
+#define CP11X_PCIE2_BASE	f2640000
+
+#include "armada-cp115.dtsi"
+
+#undef CP11X_NAME
+#undef CP11X_BASE
+#undef CP11X_PCIEx_MEM_BASE
+#undef CP11X_PCIEx_MEM_SIZE
+#undef CP11X_PCIE0_BASE
+#undef CP11X_PCIE1_BASE
+#undef CP11X_PCIE2_BASE
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 25+ messages in thread

* [PATCH 18/20] arm64: dts: marvell: Add support for Marvell CN9130-DB
  2019-08-06 14:54 [PATCH 00/20] Add new Marvell CN9130 SoC support Miquel Raynal
                   ` (16 preceding siblings ...)
  2019-08-06 14:54 ` [PATCH 17/20] arm64: dts: marvell: Add support for Marvell CN9130 SoC support Miquel Raynal
@ 2019-08-06 14:54 ` Miquel Raynal
  2019-08-06 14:54 ` [PATCH 19/20] arm64: dts: marvell: Add support for Marvell CN9131-DB Miquel Raynal
  2019-08-06 14:55 ` [PATCH 20/20] arm64: dts: marvell: Add support for Marvell CN9132-DB Miquel Raynal
  19 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-08-06 14:54 UTC (permalink / raw)
  To: Rob Herring, Mark Rutland
  Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
	Gregory Clement, Maxime Chevallier, Nadav Haklai,
	Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
	linux-arm-kernel

From: Grzegorz Jaszczyk <jaz@semihalf.com>

Add basic support for the Marvell CN9130 modular development board. It
is based on a CN9130 SoC (one AP807 and one internal CP115), extended
via 2xMoCi interface to possibly add up to two more external CP115
(one located on the main board and the other on the board extension).

Available interfaces:
* AP UART
* AP eMMC
* AP SDHCI (disabled)
* CPO GPIO-0
* CPO GPIO-1
* CP0 CRYPTO-0 (disabled)
* CP0 I2C-0
* CP0 I2C-1
* CP0 SDHCI-0
* CP0 NAND-0
* CP0 SPI-1
* CP0 ETH-0 (SFI with SFP cage not working yet, disabled)
* CP0 ETH-1 (RGMII)
* CP0 ETH-2 (RGMII)
* CP0 SATA-0-1
* CP0 USB3-0 (High-speed only)
* CP0 USB3-1 (High-speed only)
* CP0 PCIe-0 x4

Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 arch/arm64/boot/dts/marvell/Makefile      |   1 +
 arch/arm64/boot/dts/marvell/cn9130-db.dts | 403 ++++++++++++++++++++++
 2 files changed, 404 insertions(+)
 create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db.dts

diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
index caed4334f27d..922910d05863 100644
--- a/arch/arm64/boot/dts/marvell/Makefile
+++ b/arch/arm64/boot/dts/marvell/Makefile
@@ -9,3 +9,4 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-db.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin-singleshot.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-8080-db.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += cn9130-db.dtb
diff --git a/arch/arm64/boot/dts/marvell/cn9130-db.dts b/arch/arm64/boot/dts/marvell/cn9130-db.dts
new file mode 100644
index 000000000000..ce49a70d88a0
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/cn9130-db.dts
@@ -0,0 +1,403 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Marvell International Ltd.
+ *
+ * Device tree for the CN9130-DB board.
+ */
+
+#include "cn9130.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Marvell Armada CN9130-DB";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	aliases {
+		gpio1 = &cp0_gpio1;
+		gpio2 = &cp0_gpio2;
+		i2c0 = &cp0_i2c0;
+		ethernet0 = &cp0_eth0;
+		ethernet1 = &cp0_eth1;
+		ethernet2 = &cp0_eth2;
+		spi1 = &cp0_spi0;
+		spi2 = &cp0_spi1;
+	};
+
+	memory@00000000 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+
+	ap0_reg_sd_vccq: ap0_sd_vccq@0 {
+		compatible = "regulator-gpio";
+		regulator-name = "ap0_sd_vccq";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&expander0 8 GPIO_ACTIVE_HIGH>;
+		states = <1800000 0x1 3300000 0x0>;
+	};
+
+	cp0_reg_usb3_vbus0: cp0_usb3_vbus@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "cp0-xhci0-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&expander0 0 GPIO_ACTIVE_HIGH>;
+	};
+
+	cp0_usb3_0_phy0: cp0_usb3_phy@0 {
+		compatible = "usb-nop-xceiv";
+		vcc-supply = <&cp0_reg_usb3_vbus0>;
+	};
+
+	cp0_reg_usb3_vbus1: cp0_usb3_vbus@1 {
+		compatible = "regulator-fixed";
+		regulator-name = "cp0-xhci1-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&expander0 1 GPIO_ACTIVE_HIGH>;
+	};
+
+	cp0_usb3_0_phy1: cp0_usb3_phy@1 {
+		compatible = "usb-nop-xceiv";
+		vcc-supply = <&cp0_reg_usb3_vbus1>;
+	};
+
+	cp0_reg_sd_vccq: cp0_sd_vccq@0 {
+		compatible = "regulator-gpio";
+		regulator-name = "cp0_sd_vccq";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&expander0 15 GPIO_ACTIVE_HIGH>;
+		states = <1800000 0x1
+			  3300000 0x0>;
+	};
+
+	cp0_reg_sd_vcc: cp0_sd_vcc@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "cp0_sd_vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&expander0 14 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	cp0_sfp_eth0: sfp-eth@0 {
+		compatible = "sff,sfp";
+		i2c-bus = <&cp0_sfpp0_i2c>;
+		los-gpio = <&cp0_module_expander1 11 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpio = <&cp0_module_expander1 10 GPIO_ACTIVE_LOW>;
+		tx-disable-gpio = <&cp0_module_expander1 9 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpio = <&cp0_module_expander1 8 GPIO_ACTIVE_HIGH>;
+		/*
+		 * SFP cages are unconnected on early PCBs because of an the I2C
+		 * lanes not being connected. Prevent the port for being
+		 * unusable by disabling the SFP node.
+		 */
+		status = "disabled";
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+/* on-board eMMC - U9 */
+&ap_sdhci0 {
+	pinctrl-names = "default";
+	bus-width = <8>;
+	vqmmc-supply = <&ap0_reg_sd_vccq>;
+	status = "okay";
+};
+
+&cp0_crypto {
+	status = "disabled";
+};
+
+&cp0_ethernet {
+	status = "okay";
+};
+
+/* SLM-1521-V2, CON9 */
+&cp0_eth0 {
+	status = "disabled";
+	phy-mode = "10gbase-kr";
+	/* Generic PHY, providing serdes lanes */
+	phys = <&cp0_comphy4 0>;
+	managed = "in-band-status";
+	sfp = <&cp0_sfp_eth0>;
+};
+
+/* CON56 */
+&cp0_eth1 {
+	status = "okay";
+	phy = <&phy0>;
+	phy-mode = "rgmii-id";
+};
+
+/* CON57 */
+&cp0_eth2 {
+	status = "okay";
+	phy = <&phy1>;
+	phy-mode = "rgmii-id";
+};
+
+&cp0_gpio1 {
+	status = "okay";
+};
+
+&cp0_gpio2 {
+	status = "okay";
+};
+
+&cp0_i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&cp0_i2c0_pins>;
+	clock-frequency = <100000>;
+
+	/* U36 */
+	expander0: pca953x@21 {
+		compatible = "nxp,pca9555";
+		pinctrl-names = "default";
+		gpio-controller;
+		#gpio-cells = <2>;
+		reg = <0x21>;
+		status = "okay";
+	};
+
+	/* U42 */
+	eeprom0: eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <0x20>;
+	};
+
+	/* U38 */
+	eeprom1: eeprom@57 {
+		compatible = "atmel,24c64";
+		reg = <0x57>;
+		pagesize = <0x20>;
+	};
+};
+
+&cp0_i2c1 {
+	status = "okay";
+	clock-frequency = <100000>;
+
+	/* SLM-1521-V2 - U3 */
+	i2c-mux@72 { /* verify address - depends on dpr */
+		compatible = "nxp,pca9544";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x72>;
+		cp0_sfpp0_i2c: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			/* U12 */
+			cp0_module_expander1: pca9555@21 {
+				compatible = "nxp,pca9555";
+				pinctrl-names = "default";
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x21>;
+			};
+
+		};
+	};
+};
+
+&cp0_mdio {
+	status = "okay";
+
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+	};
+
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+};
+
+/* U54 */
+&cp0_nand_controller {
+	pinctrl-names = "default";
+	pinctrl-0 = <&nand_pins &nand_rb>;
+
+	nand@0 {
+		reg = <0>;
+		label = "main-storage";
+		nand-rb = <0>;
+		nand-ecc-mode = "hw";
+		nand-on-flash-bbt;
+		nand-ecc-strength = <8>;
+		nand-ecc-step-size = <512>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "U-Boot";
+				reg = <0 0x200000>;
+			};
+			partition@200000 {
+				label = "Linux";
+				reg = <0x200000 0xd00000>;
+			};
+			partition@1000000 {
+				label = "Filesystem";
+				reg = <0x1000000 0x3f000000>;
+			};
+		};
+	};
+};
+
+/* SLM-1521-V2, CON6 */
+&cp0_pcie0 {
+	status = "okay";
+	num-lanes = <4>;
+	num-viewport = <8>;
+	/* Generic PHY, providing serdes lanes */
+	phys = <&cp0_comphy0 0
+		&cp0_comphy1 0
+		&cp0_comphy2 0
+		&cp0_comphy3 0>;
+};
+
+&cp0_sata0 {
+	status = "okay";
+
+	/* SLM-1521-V2, CON2 */
+	sata-port@1 {
+		status = "okay";
+		/* Generic PHY, providing serdes lanes */
+		phys = <&cp0_comphy5 1>;
+	};
+};
+
+/* CON 28 */
+&cp0_sdhci0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&cp0_sdhci_pins
+		     &cp0_sdhci_cd_pins>;
+	bus-width = <4>;
+	cd-gpios = <&cp0_gpio2 11 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	vqmmc-supply = <&cp0_reg_sd_vccq>;
+	vmmc-supply = <&cp0_reg_sd_vcc>;
+};
+
+/* U55 */
+&cp0_spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&cp0_spi0_pins>;
+	reg = <0x700680 0x50>;
+
+	spi-flash@0 {
+		#address-cells = <0x1>;
+		#size-cells = <0x1>;
+		compatible = "jedec,spi-nor";
+		reg = <0x0>;
+		/* On-board MUX does not allow higher frequencies */
+		spi-max-frequency = <40000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "U-Boot-0";
+				reg = <0x0 0x200000>;
+			};
+
+			partition@400000 {
+				label = "Filesystem-0";
+				reg = <0x200000 0xe00000>;
+			};
+		};
+	};
+};
+
+&cp0_syscon0 {
+	cp0_pinctrl: pinctrl {
+		compatible = "marvell,cp115-standalone-pinctrl";
+
+		cp0_i2c0_pins: cp0-i2c-pins-0 {
+			marvell,pins = "mpp37", "mpp38";
+			marvell,function = "i2c0";
+		};
+		cp0_i2c1_pins: cp0-i2c-pins-1 {
+			marvell,pins = "mpp35", "mpp36";
+			marvell,function = "i2c1";
+		};
+		cp0_ge1_rgmii_pins: cp0-ge-rgmii-pins-0 {
+			marvell,pins = "mpp0", "mpp1", "mpp2",
+				       "mpp3", "mpp4", "mpp5",
+				       "mpp6", "mpp7", "mpp8",
+				       "mpp9", "mpp10", "mpp11";
+			marvell,function = "ge0";
+		};
+		cp0_ge2_rgmii_pins: cp0-ge-rgmii-pins-1 {
+			marvell,pins = "mpp44", "mpp45", "mpp46",
+				       "mpp47", "mpp48", "mpp49",
+				       "mpp50", "mpp51", "mpp52",
+				       "mpp53", "mpp54", "mpp55";
+			marvell,function = "ge1";
+		};
+		cp0_sdhci_cd_pins: cp0-sdhci-cd-pins-0 {
+			marvell,pins = "mpp43";
+			marvell,function = "gpio";
+		};
+		cp0_sdhci_pins: cp0-sdhi-pins-0 {
+			marvell,pins = "mpp56", "mpp57", "mpp58",
+				       "mpp59", "mpp60", "mpp61";
+			marvell,function = "sdio";
+		};
+		cp0_spi0_pins: cp0-spi-pins-0 {
+			marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
+			marvell,function = "spi1";
+		};
+		nand_pins: nand-pins {
+			marvell,pins = "mpp15", "mpp16", "mpp17", "mpp18",
+				       "mpp19", "mpp20", "mpp21", "mpp22",
+				       "mpp23", "mpp24", "mpp25", "mpp26",
+				       "mpp27";
+			marvell,function = "dev";
+		};
+		nand_rb: nand-rb {
+			marvell,pins = "mpp13";
+			marvell,function = "nf";
+		};
+	};
+};
+
+&cp0_usb3_0 {
+	status = "okay";
+	usb-phy = <&cp0_usb3_0_phy0>;
+	phy-names = "usb";
+};
+
+&cp0_usb3_1 {
+	status = "okay";
+	usb-phy = <&cp0_usb3_0_phy1>;
+	phy-names = "usb";
+};
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 25+ messages in thread

* [PATCH 19/20] arm64: dts: marvell: Add support for Marvell CN9131-DB
  2019-08-06 14:54 [PATCH 00/20] Add new Marvell CN9130 SoC support Miquel Raynal
                   ` (17 preceding siblings ...)
  2019-08-06 14:54 ` [PATCH 18/20] arm64: dts: marvell: Add support for Marvell CN9130-DB Miquel Raynal
@ 2019-08-06 14:54 ` Miquel Raynal
  2019-08-06 14:55 ` [PATCH 20/20] arm64: dts: marvell: Add support for Marvell CN9132-DB Miquel Raynal
  19 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-08-06 14:54 UTC (permalink / raw)
  To: Rob Herring, Mark Rutland
  Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
	Gregory Clement, Maxime Chevallier, Nadav Haklai,
	Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
	linux-arm-kernel

From: Grzegorz Jaszczyk <jaz@semihalf.com>

Extend the support of the CN9130 by adding an external CP115.

The last number indicates how many external CP115 are used.

New available interfaces:
* CP1 CRYPTO-0 (disabled)
* CP1 ETH-0 (SFI, problem with the SFP cage, disabled)
* CP1 GPIO-1
* CP1 GPIO-2
* CP1 I2C-0
* CP1 PCIe-0 x2
* CP1 SPI-1
* CP1 SATA-0-1
* CP1 USB3-1

Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 arch/arm64/boot/dts/marvell/Makefile      |   1 +
 arch/arm64/boot/dts/marvell/cn9131-db.dts | 202 ++++++++++++++++++++++
 2 files changed, 203 insertions(+)
 create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db.dts

diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
index 922910d05863..92767d5be069 100644
--- a/arch/arm64/boot/dts/marvell/Makefile
+++ b/arch/arm64/boot/dts/marvell/Makefile
@@ -10,3 +10,4 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin-singleshot.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-8080-db.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += cn9130-db.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += cn9131-db.dtb
diff --git a/arch/arm64/boot/dts/marvell/cn9131-db.dts b/arch/arm64/boot/dts/marvell/cn9131-db.dts
new file mode 100644
index 000000000000..3c975f98b2a3
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/cn9131-db.dts
@@ -0,0 +1,202 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Marvell International Ltd.
+ *
+ * Device tree for the CN9131-DB board.
+ */
+
+#include "cn9130-db.dts"
+
+/ {
+	model = "Marvell Armada CN9131-DB";
+	compatible = "marvell,cn9131", "marvell,cn9130",
+		     "marvell,armada-ap807-quad", "marvell,armada-ap807";
+
+	aliases {
+		gpio3 = &cp1_gpio1;
+		gpio4 = &cp1_gpio2;
+		ethernet3 = &cp1_eth0;
+		ethernet4 = &cp1_eth1;
+	};
+
+	cp1_reg_usb3_vbus0: cp1_usb3_vbus@0 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&cp1_xhci0_vbus_pins>;
+		regulator-name = "cp1-xhci0-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&cp1_gpio1 3 GPIO_ACTIVE_HIGH>;
+	};
+
+	cp1_usb3_0_phy0: cp1_usb3_phy0 {
+		compatible = "usb-nop-xceiv";
+		vcc-supply = <&cp1_reg_usb3_vbus0>;
+	};
+
+	cp1_sfp_eth1: sfp-eth1 {
+		compatible = "sff,sfp";
+		i2c-bus = <&cp1_i2c0>;
+		los-gpio = <&cp1_gpio1 11 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpio = <&cp1_gpio1 10 GPIO_ACTIVE_LOW>;
+		tx-disable-gpio = <&cp1_gpio1 9 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpio = <&cp1_gpio1 8 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&cp1_sfp_pins>;
+		/*
+		 * SFP cages are unconnected on early PCBs because of an the I2C
+		 * lanes not being connected. Prevent the port for being
+		 * unusable by disabling the SFP node.
+		 */
+		status = "disabled";
+	};
+};
+
+/*
+ * Instantiate the first slave CP115
+ */
+
+#define CP11X_NAME		cp1
+#define CP11X_BASE		f4000000
+#define CP11X_PCIEx_MEM_BASE(iface) (0xe2000000 + (iface * 0x1000000))
+#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000
+#define CP11X_PCIE0_BASE	f4600000
+#define CP11X_PCIE1_BASE	f4620000
+#define CP11X_PCIE2_BASE	f4640000
+
+#include "armada-cp115.dtsi"
+
+#undef CP11X_NAME
+#undef CP11X_BASE
+#undef CP11X_PCIEx_MEM_BASE
+#undef CP11X_PCIEx_MEM_SIZE
+#undef CP11X_PCIE0_BASE
+#undef CP11X_PCIE1_BASE
+#undef CP11X_PCIE2_BASE
+
+&cp1_crypto {
+	status = "disabled";
+};
+
+&cp1_ethernet {
+	status = "okay";
+};
+
+/* CON50 */
+&cp1_eth0 {
+	status = "disabled";
+	phy-mode = "10gbase-kr";
+	/* Generic PHY, providing serdes lanes */
+	phys = <&cp1_comphy4 0>;
+	managed = "in-band-status";
+	sfp = <&cp1_sfp_eth1>;
+};
+
+&cp1_gpio1 {
+	status = "okay";
+};
+
+&cp1_gpio2 {
+	status = "okay";
+};
+
+&cp1_i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&cp1_i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+/* CON40 */
+&cp1_pcie0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&cp1_pcie_reset_pins>;
+	num-lanes = <2>;
+	num-viewport = <8>;
+	marvell,reset-gpio = <&cp1_gpio1 0 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+	/* Generic PHY, providing serdes lanes */
+	phys = <&cp1_comphy0 0
+		&cp1_comphy1 0>;
+};
+
+&cp1_sata0 {
+	status = "okay";
+
+	/* CON32 */
+	sata-port@1 {
+		/* Generic PHY, providing serdes lanes */
+		phys = <&cp1_comphy5 1>;
+	};
+};
+
+/* U24 */
+&cp1_spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&cp1_spi0_pins>;
+	reg = <0x700680 0x50>;
+
+	spi-flash@0 {
+		#address-cells = <0x1>;
+		#size-cells = <0x1>;
+		compatible = "jedec,spi-nor";
+		reg = <0x0>;
+		/* On-board MUX does not allow higher frequencies */
+		spi-max-frequency = <40000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "U-Boot-1";
+				reg = <0x0 0x200000>;
+			};
+
+			partition@400000 {
+				label = "Filesystem-1";
+				reg = <0x200000 0xe00000>;
+			};
+		};
+	};
+
+};
+
+&cp1_syscon0 {
+	cp1_pinctrl: pinctrl {
+		compatible = "marvell,cp115-standalone-pinctrl";
+
+		cp1_i2c0_pins: cp1-i2c-pins-0 {
+			marvell,pins = "mpp37", "mpp38";
+			marvell,function = "i2c0";
+		};
+		cp1_spi0_pins: cp1-spi-pins-0 {
+			marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
+			marvell,function = "spi1";
+		};
+		cp1_xhci0_vbus_pins: cp1-xhci0-vbus-pins {
+			marvell,pins = "mpp3";
+			marvell,function = "gpio";
+		};
+		cp1_sfp_pins: sfp-pins {
+			marvell,pins = "mpp8", "mpp9", "mpp10", "mpp11";
+			marvell,function = "gpio";
+		};
+		cp1_pcie_reset_pins: cp1-pcie-reset-pins {
+			marvell,pins = "mpp0";
+			marvell,function = "gpio";
+		};
+	};
+};
+
+/* CON58 */
+&cp1_usb3_1 {
+	status = "okay";
+	usb-phy = <&cp1_usb3_0_phy0>;
+	/* Generic PHY, providing serdes lanes */
+	phys = <&cp1_comphy3 1>;
+	phy-names = "usb";
+};
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 25+ messages in thread

* [PATCH 20/20] arm64: dts: marvell: Add support for Marvell CN9132-DB
  2019-08-06 14:54 [PATCH 00/20] Add new Marvell CN9130 SoC support Miquel Raynal
                   ` (18 preceding siblings ...)
  2019-08-06 14:54 ` [PATCH 19/20] arm64: dts: marvell: Add support for Marvell CN9131-DB Miquel Raynal
@ 2019-08-06 14:55 ` Miquel Raynal
  19 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-08-06 14:55 UTC (permalink / raw)
  To: Rob Herring, Mark Rutland
  Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
	Gregory Clement, Maxime Chevallier, Nadav Haklai,
	Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
	linux-arm-kernel

From: Grzegorz Jaszczyk <jaz@semihalf.com>

Extend the support of the CN9131 with yet another additional CP115.

The last number indicates how many external CP115 are used.

New available interfaces:
* CP2 CRYPTO-0 (disabled)
* CP2 ETH-0 (SFI, problem with the SFP cage, disabled)
* CP2 GPIO-1
* CP2 GPIO-2
* CP2 I2C-0
* CP2 PCIe-0 x2
* CP2 PCIe-2 x1 (disabled)
* CP2 SDHCI-0
* CP2 USB3-1 (High-speed)

Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 arch/arm64/boot/dts/marvell/Makefile      |   1 +
 arch/arm64/boot/dts/marvell/cn9132-db.dts | 221 ++++++++++++++++++++++
 2 files changed, 222 insertions(+)
 create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db.dts

diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
index 92767d5be069..2af91b78d645 100644
--- a/arch/arm64/boot/dts/marvell/Makefile
+++ b/arch/arm64/boot/dts/marvell/Makefile
@@ -11,3 +11,4 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin-singleshot.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-8080-db.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += cn9130-db.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += cn9131-db.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db.dtb
diff --git a/arch/arm64/boot/dts/marvell/cn9132-db.dts b/arch/arm64/boot/dts/marvell/cn9132-db.dts
new file mode 100644
index 000000000000..4ef0df3097ca
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/cn9132-db.dts
@@ -0,0 +1,221 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Marvell International Ltd.
+ *
+ * Device tree for the CN9132-DB board.
+ */
+
+#include "cn9131-db.dts"
+
+/ {
+	model = "Marvell Armada CN9132-DB";
+	compatible = "marvell,cn9132", "marvell,cn9131", "marvell,cn9130",
+		     "marvell,armada-ap807-quad", "marvell,armada-ap807";
+
+	aliases {
+		gpio5 = &cp2_gpio1;
+		gpio6 = &cp2_gpio2;
+		ethernet5 = &cp2_eth0;
+	};
+
+	cp2_reg_usb3_vbus0: cp2_usb3_vbus@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "cp2-xhci0-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&cp2_gpio1 2 GPIO_ACTIVE_HIGH>;
+	};
+
+	cp2_usb3_0_phy0: cp2_usb3_phy0 {
+		compatible = "usb-nop-xceiv";
+		vcc-supply = <&cp2_reg_usb3_vbus0>;
+	};
+
+	cp2_reg_usb3_vbus1: cp2_usb3_vbus@1 {
+		compatible = "regulator-fixed";
+		regulator-name = "cp2-xhci1-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&cp2_gpio1 3 GPIO_ACTIVE_HIGH>;
+	};
+
+	cp2_usb3_0_phy1: cp2_usb3_phy1 {
+		compatible = "usb-nop-xceiv";
+		vcc-supply = <&cp2_reg_usb3_vbus1>;
+	};
+
+	cp2_reg_sd_vccq: cp2_sd_vccq@0 {
+		compatible = "regulator-gpio";
+		regulator-name = "cp2_sd_vcc";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&cp2_gpio2 17 GPIO_ACTIVE_HIGH>;
+		states = <1800000 0x1 3300000 0x0>;
+	};
+
+	cp2_sfp_eth0: sfp-eth0 {
+		compatible = "sff,sfp";
+		i2c-bus = <&cp2_sfpp0_i2c>;
+		los-gpio = <&cp2_module_expander1 11 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpio = <&cp2_module_expander1 10 GPIO_ACTIVE_LOW>;
+		tx-disable-gpio = <&cp2_module_expander1 9 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpio = <&cp2_module_expander1 8 GPIO_ACTIVE_HIGH>;
+		/*
+		 * SFP cages are unconnected on early PCBs because of an the I2C
+		 * lanes not being connected. Prevent the port for being
+		 * unusable by disabling the SFP node.
+		 */
+		status = "disabled";
+	};
+};
+
+/*
+ * Instantiate the second slave CP115
+ */
+
+#define CP11X_NAME		cp2
+#define CP11X_BASE		f6000000
+#define CP11X_PCIEx_MEM_BASE(iface) (0xe5000000 + (iface * 0x1000000))
+#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000
+#define CP11X_PCIE0_BASE	f6600000
+#define CP11X_PCIE1_BASE	f6620000
+#define CP11X_PCIE2_BASE	f6640000
+
+#include "armada-cp115.dtsi"
+
+#undef CP11X_NAME
+#undef CP11X_BASE
+#undef CP11X_PCIEx_MEM_BASE
+#undef CP11X_PCIEx_MEM_SIZE
+#undef CP11X_PCIE0_BASE
+#undef CP11X_PCIE1_BASE
+#undef CP11X_PCIE2_BASE
+
+&cp2_crypto {
+	status = "disabled";
+};
+
+&cp2_ethernet {
+	status = "okay";
+};
+
+/* SLM-1521-V2, CON9 */
+&cp2_eth0 {
+	status = "disabled";
+	phy-mode = "10gbase-kr";
+	/* Generic PHY, providing serdes lanes */
+	phys = <&cp2_comphy4 0>;
+	managed = "in-band-status";
+	sfp = <&cp2_sfp_eth0>;
+};
+
+&cp2_gpio1 {
+	status = "okay";
+};
+
+&cp2_gpio2 {
+	status = "okay";
+};
+
+&cp2_i2c0 {
+	clock-frequency = <100000>;
+
+	/* SLM-1521-V2 - U3 */
+	i2c-mux@72 {
+		compatible = "nxp,pca9544";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x72>;
+		cp2_sfpp0_i2c: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			/* U12 */
+			cp2_module_expander1: pca9555@21 {
+				compatible = "nxp,pca9555";
+				pinctrl-names = "default";
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x21>;
+			};
+		};
+	};
+};
+
+/* SLM-1521-V2, CON6 */
+&cp2_pcie0 {
+	status = "okay";
+	num-lanes = <2>;
+	num-viewport = <8>;
+	/* Generic PHY, providing serdes lanes */
+	phys = <&cp2_comphy0 0
+		&cp2_comphy1 0>;
+};
+
+/* SLM-1521-V2, CON8 */
+&cp2_pcie2 {
+	status = "okay";
+	num-lanes = <1>;
+	num-viewport = <8>;
+	/* Generic PHY, providing serdes lanes */
+	phys = <&cp2_comphy5 2>;
+};
+
+&cp2_sata0 {
+	status = "okay";
+
+	/* SLM-1521-V2, CON4 */
+	sata-port@0 {
+		/* Generic PHY, providing serdes lanes */
+		phys = <&cp2_comphy2 0>;
+	};
+};
+
+/* CON 2 on SLM-1683 - microSD */
+&cp2_sdhci0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&cp2_sdhci_pins>;
+	bus-width = <4>;
+	cd-gpios = <&cp2_gpio2 23 GPIO_ACTIVE_LOW>;
+	vqmmc-supply = <&cp2_reg_sd_vccq>;
+};
+
+&cp2_syscon0 {
+	cp2_pinctrl: pinctrl {
+		compatible = "marvell,cp115-standalone-pinctrl";
+
+		cp2_i2c0_pins: cp2-i2c-pins-0 {
+			marvell,pins = "mpp37", "mpp38";
+			marvell,function = "i2c0";
+		};
+		cp2_sdhci_pins: cp2-sdhi-pins-0 {
+			marvell,pins = "mpp56", "mpp57", "mpp58",
+				       "mpp59", "mpp60", "mpp61";
+			marvell,function = "sdio";
+		};
+	};
+};
+
+&cp2_usb3_0 {
+	status = "okay";
+	usb-phy = <&cp2_usb3_0_phy0>;
+	phy-names = "usb";
+};
+
+/* SLM-1521-V2, CON11 */
+&cp2_usb3_1 {
+	status = "okay";
+	usb-phy = <&cp2_usb3_0_phy1>;
+	phy-names = "usb";
+	/* Generic PHY, providing serdes lanes */
+	phys = <&cp2_comphy3 1>;
+};
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 25+ messages in thread

* Re: [PATCH 03/20] dt-bindings: ap80x: replace AP806 with AP80x
  2019-08-06 14:54 ` [PATCH 03/20] dt-bindings: ap80x: replace AP806 with AP80x Miquel Raynal
@ 2019-08-21 19:32   ` Rob Herring
  0 siblings, 0 replies; 25+ messages in thread
From: Rob Herring @ 2019-08-21 19:32 UTC (permalink / raw)
  To: Miquel Raynal
  Cc: Mark Rutland, devicetree, Yan Markman, Antoine Tenart,
	Grzegorz Jaszczyk, Gregory Clement, Maxime Chevallier,
	Nadav Haklai, Thomas Petazzoni, Miquel Raynal, Stefan Chulski,
	Marcin Wojtas, Ben Peled, linux-arm-kernel

On Tue,  6 Aug 2019 16:54:43 +0200, Miquel Raynal wrote:
> From: Ben Peled <bpeled@marvell.com>
> 
> Rename the text file and update "AP806" into "AP806/AP807" where
> relevant.
> 
> Signed-off-by: Ben Peled <bpeled@marvell.com>
> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
> ---
>  ...-controller.txt => ap80x-system-controller.txt} | 14 +++++++-------
>  1 file changed, 7 insertions(+), 7 deletions(-)
>  rename Documentation/devicetree/bindings/arm/marvell/{ap806-system-controller.txt => ap80x-system-controller.txt} (91%)
> 

Reviewed-by: Rob Herring <robh@kernel.org>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 25+ messages in thread

* Re: [PATCH 16/20] dt-bindings: marvell: Declare the CN913x SoC compatibles
  2019-08-06 14:54 ` [PATCH 16/20] dt-bindings: marvell: Declare the CN913x SoC compatibles Miquel Raynal
@ 2019-08-21 19:37   ` Rob Herring
  2019-08-24 11:30     ` Miquel Raynal
  0 siblings, 1 reply; 25+ messages in thread
From: Rob Herring @ 2019-08-21 19:37 UTC (permalink / raw)
  To: Miquel Raynal
  Cc: Mark Rutland, devicetree, Yan Markman, Antoine Tenart,
	Grzegorz Jaszczyk, Gregory Clement, Maxime Chevallier,
	Nadav Haklai, Thomas Petazzoni, Stefan Chulski, Marcin Wojtas,
	linux-arm-kernel

On Tue, Aug 06, 2019 at 04:54:56PM +0200, Miquel Raynal wrote:
> From: Grzegorz Jaszczyk <jaz@semihalf.com>
> 
> Describe the compatible properties for the new Marvell SoCs:
> * CN9130: 1x AP807-quad + 1x CP115 (1x embedded)
> * CN9131: 1x AP807-quad + 2x CP115 (1x embedded + 1x modular)
> * CN9132: 1x AP807-quad + 3x CP115 (1x embedded + 2x modular)
> 
> CP115 are similar to CP110 in terms of features.
> 
> There are three development boards based on these SoCs:
> * CN9130-DB: comes as a single mother board (with the CP115 bundled)
> * CN9131-DB: same as CN9130-DB with one additional modular CP115
> * CN9132-DB: same as CN9130-DB with two additional modular CP115
> 
> Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
> ---
>  .../bindings/arm/marvell/armada-7k-8k.txt           | 13 ++++++++++++-
>  1 file changed, 12 insertions(+), 1 deletion(-)

Please convert this to DT schema first.

> 
> diff --git a/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.txt b/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.txt
> index df98a9c82a8c..8eb34ca4c4f0 100644
> --- a/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.txt
> +++ b/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.txt
> @@ -1,7 +1,7 @@
>  Marvell Armada 7K/8K Platforms Device Tree Bindings
>  ---------------------------------------------------
>  
> -Boards using a SoC of the Marvell Armada 7K or 8K families must carry
> +Boards using a SoC of the Marvell Armada 7K/8K or CN913x families must carry
>  the following root node property:
>  
>   - compatible, with one of the following values:
> @@ -18,6 +18,17 @@ the following root node property:
>     - "marvell,armada8040", "marvell,armada-ap806-quad", "marvell,armada-ap806"
>        when the SoC being used is the Armada 8040
>  
> +   - "marvell,cn9130", "marvell,armada-ap807-quad", "marvell,armada-ap807"
> +      when the SoC being used is the Armada CN9130 with no external CP.
> +
> +   - "marvell,cn9131", "marvell,cn9130",
> +     "marvell,armada-ap807-quad", "marvell,armada-ap807"
> +      when the SoC being used is the Armada CN9130 with one external CP.
> +
> +   - "marvell,cn9132", "marvell,cn9131", "marvell,cn9130",
> +     "marvell,armada-ap807-quad", "marvell,armada-ap807"

It's generally not all that useful to have all these compatibles.

> +      when the SoC being used is the Armada CN9130 with two external CPs.

Is the number of external CPs not discoverable somewhere else in the DT?

> +
>  Example:
>  
>  compatible = "marvell,armada7040-db", "marvell,armada7040",
> -- 
> 2.20.1
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 25+ messages in thread

* Re: [PATCH 16/20] dt-bindings: marvell: Declare the CN913x SoC compatibles
  2019-08-21 19:37   ` Rob Herring
@ 2019-08-24 11:30     ` Miquel Raynal
  0 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-08-24 11:30 UTC (permalink / raw)
  To: Rob Herring
  Cc: Mark Rutland, devicetree, Yan Markman, Antoine Tenart,
	Grzegorz Jaszczyk, Gregory Clement, Maxime Chevallier,
	Nadav Haklai, Thomas Petazzoni, Stefan Chulski, Marcin Wojtas,
	linux-arm-kernel

Hi Rob,

Rob Herring <robh@kernel.org> wrote on Wed, 21 Aug 2019 14:37:26 -0500:

> On Tue, Aug 06, 2019 at 04:54:56PM +0200, Miquel Raynal wrote:
> > From: Grzegorz Jaszczyk <jaz@semihalf.com>
> > 
> > Describe the compatible properties for the new Marvell SoCs:
> > * CN9130: 1x AP807-quad + 1x CP115 (1x embedded)
> > * CN9131: 1x AP807-quad + 2x CP115 (1x embedded + 1x modular)
> > * CN9132: 1x AP807-quad + 3x CP115 (1x embedded + 2x modular)
> > 
> > CP115 are similar to CP110 in terms of features.
> > 
> > There are three development boards based on these SoCs:
> > * CN9130-DB: comes as a single mother board (with the CP115 bundled)
> > * CN9131-DB: same as CN9130-DB with one additional modular CP115
> > * CN9132-DB: same as CN9130-DB with two additional modular CP115
> > 
> > Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
> > Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
> > ---
> >  .../bindings/arm/marvell/armada-7k-8k.txt           | 13 ++++++++++++-
> >  1 file changed, 12 insertions(+), 1 deletion(-)  
> 
> Please convert this to DT schema first.

As you wish.

> 
> > 
> > diff --git a/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.txt b/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.txt
> > index df98a9c82a8c..8eb34ca4c4f0 100644
> > --- a/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.txt
> > +++ b/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.txt
> > @@ -1,7 +1,7 @@
> >  Marvell Armada 7K/8K Platforms Device Tree Bindings
> >  ---------------------------------------------------
> >  
> > -Boards using a SoC of the Marvell Armada 7K or 8K families must carry
> > +Boards using a SoC of the Marvell Armada 7K/8K or CN913x families must carry
> >  the following root node property:
> >  
> >   - compatible, with one of the following values:
> > @@ -18,6 +18,17 @@ the following root node property:
> >     - "marvell,armada8040", "marvell,armada-ap806-quad", "marvell,armada-ap806"
> >        when the SoC being used is the Armada 8040
> >  
> > +   - "marvell,cn9130", "marvell,armada-ap807-quad", "marvell,armada-ap807"
> > +      when the SoC being used is the Armada CN9130 with no external CP.
> > +
> > +   - "marvell,cn9131", "marvell,cn9130",
> > +     "marvell,armada-ap807-quad", "marvell,armada-ap807"
> > +      when the SoC being used is the Armada CN9130 with one external CP.
> > +
> > +   - "marvell,cn9132", "marvell,cn9131", "marvell,cn9130",
> > +     "marvell,armada-ap807-quad", "marvell,armada-ap807"  
> 
> It's generally not all that useful to have all these compatibles.
> 
> > +      when the SoC being used is the Armada CN9130 with two external CPs.  
> 
> Is the number of external CPs not discoverable somewhere else in the DT?

I don't think so.

What do you suggest? Keep only the marvell,cn9130 compatible? I am not
sure having the three compatibles is actually useful but for the reader
I find it more friendly. Of course the model name will reflect the
number of external CP but from a computational point of view that's
hard to parse if needed.

> 
> > +
> >  Example:
> >  
> >  compatible = "marvell,armada7040-db", "marvell,armada7040",
> > -- 
> > 2.20.1
> >   

Thanks,
Miquèl

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 25+ messages in thread

* Re: [PATCH 05/20] arm64: dts: marvell: Prepare the introduction of AP807 based SoCs
  2019-08-06 14:54 ` [PATCH 05/20] arm64: dts: marvell: Prepare the introduction of AP807 based SoCs Miquel Raynal
@ 2019-08-27 15:20   ` Gregory CLEMENT
  0 siblings, 0 replies; 25+ messages in thread
From: Gregory CLEMENT @ 2019-08-27 15:20 UTC (permalink / raw)
  To: Miquel Raynal, Rob Herring, Mark Rutland
  Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
	Maxime Chevallier, Nadav Haklai, Thomas Petazzoni, Miquel Raynal,
	Konstantin Porotchkin, Stefan Chulski, Marcin Wojtas,
	linux-arm-kernel

Hi Miquel,

> From: Konstantin Porotchkin <kostap@marvell.com>
>
> Prepare the support for Marvell AP807 die. This die is very similar to
> AP806 but uses different DDR PHY. AP807 is a major component of CN9130
> SoC series.
>
> Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
> ---
>  arch/arm64/boot/dts/marvell/armada-ap806.dtsi | 448 +----------------
>  arch/arm64/boot/dts/marvell/armada-ap80x.dtsi | 456 ++++++++++++++++++
>  2 files changed, 458 insertions(+), 446 deletions(-)
>  create mode 100644 arch/arm64/boot/dts/marvell/armada-ap80x.dtsi
>
> diff --git a/arch/arm64/boot/dts/marvell/armada-ap806.dtsi b/arch/arm64/boot/dts/marvell/armada-ap806.dtsi
> index a23ddd46efc5..cdadb28f287e 100644
> --- a/arch/arm64/boot/dts/marvell/armada-ap806.dtsi
> +++ b/arch/arm64/boot/dts/marvell/armada-ap806.dtsi
> @@ -5,454 +5,10 @@
>   * Device Tree file for Marvell Armada AP806.
>   */
>  
> -#include <dt-bindings/interrupt-controller/arm-gic.h>
> -#include <dt-bindings/thermal/thermal.h>
> -
> -/dts-v1/;
> +#define AP_NAME		ap806

I didn't find where AP_NAME is used.

> +#include "armada-ap80x.dtsi"
[...]

> diff --git a/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi b/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi
> new file mode 100644
> index 000000000000..c44cd7c64bf6
> --- /dev/null
> +++ b/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi

[...]


> +	ap806 {

This file will be used for ap806 and for ap807 but the ap name will be
the same for both varirant?

Shouldn't you use the AP_NAME here?

Gregory

-- 
Gregory Clement, Bootlin
Embedded Linux and Kernel engineering
http://bootlin.com

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 25+ messages in thread

end of thread, back to index

Thread overview: 25+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-08-06 14:54 [PATCH 00/20] Add new Marvell CN9130 SoC support Miquel Raynal
2019-08-06 14:54 ` [PATCH 01/20] arm64: dts: marvell: Enumerate the first AP806 syscon Miquel Raynal
2019-08-06 14:54 ` [PATCH 02/20] arm64: dts: marvell: Add AP806-dual missing CPU clocks Miquel Raynal
2019-08-06 14:54 ` [PATCH 03/20] dt-bindings: ap80x: replace AP806 with AP80x Miquel Raynal
2019-08-21 19:32   ` Rob Herring
2019-08-06 14:54 ` [PATCH 04/20] MAINTAINERS: Add new Marvell CN9130-based files to track Miquel Raynal
2019-08-06 14:54 ` [PATCH 05/20] arm64: dts: marvell: Prepare the introduction of AP807 based SoCs Miquel Raynal
2019-08-27 15:20   ` Gregory CLEMENT
2019-08-06 14:54 ` [PATCH 06/20] arm64: dts: marvell: Move clocks to AP806 specific file Miquel Raynal
2019-08-06 14:54 ` [PATCH 07/20] arm64: dts: marvell: Add support for AP807/AP807-quad Miquel Raynal
2019-08-06 14:54 ` [PATCH 08/20] arm64: dts: marvell: Add AP806-dual cache description Miquel Raynal
2019-08-06 14:54 ` [PATCH 09/20] arm64: dts: marvell: Add AP806-quad " Miquel Raynal
2019-08-06 14:54 ` [PATCH 10/20] arm64: dts: marvell: Add AP807-quad " Miquel Raynal
2019-08-06 14:54 ` [PATCH 11/20] arm64: dts: marvell: Fix CP110 NAND controller node multi-line comment alignment Miquel Raynal
2019-08-06 14:54 ` [PATCH 12/20] arm64: dts: marvell: Prepare the introduction of CP115 Miquel Raynal
2019-08-06 14:54 ` [PATCH 13/20] arm64: dts: marvell: Drop PCIe I/O ranges from CP11x file Miquel Raynal
2019-08-06 14:54 ` [PATCH 14/20] arm64: dts: marvell: Externalize PCIe macros " Miquel Raynal
2019-08-06 14:54 ` [PATCH 15/20] arm64: dts: marvell: Add support for CP115 Miquel Raynal
2019-08-06 14:54 ` [PATCH 16/20] dt-bindings: marvell: Declare the CN913x SoC compatibles Miquel Raynal
2019-08-21 19:37   ` Rob Herring
2019-08-24 11:30     ` Miquel Raynal
2019-08-06 14:54 ` [PATCH 17/20] arm64: dts: marvell: Add support for Marvell CN9130 SoC support Miquel Raynal
2019-08-06 14:54 ` [PATCH 18/20] arm64: dts: marvell: Add support for Marvell CN9130-DB Miquel Raynal
2019-08-06 14:54 ` [PATCH 19/20] arm64: dts: marvell: Add support for Marvell CN9131-DB Miquel Raynal
2019-08-06 14:55 ` [PATCH 20/20] arm64: dts: marvell: Add support for Marvell CN9132-DB Miquel Raynal

Linux-ARM-Kernel Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-arm-kernel/0 linux-arm-kernel/git/0.git
	git clone --mirror https://lore.kernel.org/linux-arm-kernel/1 linux-arm-kernel/git/1.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-arm-kernel linux-arm-kernel/ https://lore.kernel.org/linux-arm-kernel \
		linux-arm-kernel@lists.infradead.org infradead-linux-arm-kernel@archiver.kernel.org
	public-inbox-index linux-arm-kernel


Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.infradead.lists.linux-arm-kernel


AGPL code for this site: git clone https://public-inbox.org/ public-inbox