[PATCH 2/2] ARM: dts: ux500: Update thermal zone

[Linus Walleij <linus.walleij@linaro.org>]

After moving the DB8500 thermal driver to use device tree
we define the default thermal zone for the Ux500 in the
device tree replacing the oldstyle hardcoded trigger
points.

This default thermal zone utilizes the cpufreq driver
(using the generic OF cpufreq back-end) as a passive
cooling device, and defines a critical trip point when
the temperature goes above 85 degrees celsius which will
(hopefully) make the system shut down if the temperature
cannot be controlled.

This default policy can later be augmented for specific
subdevices if these have tighter temperature conditions.

After this patch we get:

/sys/class/thermal/thermal_zone0 (CPU thermal zone)
This reports the rough temperature and trip points
from the thermal zone in the device tree.

By executing two yes > /dev/null & jobs fully utilizing
the two CPU cores we can notice the temperature climbing
in the thermal zone in response and falling when we kill
the jobs.

/syc/class/thermal/cooling_device0 (cpufreq cooling)
this reports all 4 available cpufreq frequencies as
states.

Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
 arch/arm/boot/dts/ste-dbx5x0.dtsi | 57 +++++++++++++++++++------------
 1 file changed, 36 insertions(+), 21 deletions(-)

diff --git a/arch/arm/boot/dts/ste-dbx5x0.dtsi b/arch/arm/boot/dts/ste-dbx5x0.dtsi
index 7953eea7c486..9ee50f339e7a 100644
--- a/arch/arm/boot/dts/ste-dbx5x0.dtsi
+++ b/arch/arm/boot/dts/ste-dbx5x0.dtsi
@@ -44,6 +44,7 @@
 			clocks = <&prcmu_clk PRCMU_ARMSS>;
 			clock-names = "cpu";
 			clock-latency = <20000>;
+			#cooling-cells = <2>;
 		};
 		CPU1: cpu@301 {
 			device_type = "cpu";
@@ -52,6 +53,39 @@
 		};
 	};
 
+	thermal-zones {
+		/*
+		 * Thermal zone for the SoC, using the thermal sensor in the
+		 * PRCMU for temperature and the cpufreq driver for passive
+		 * cooling.
+		 */
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&thermal>;
+
+			trips {
+				cpu_alert: cpu-alert {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu-crit {
+					temperature = <85000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				trip = <&cpu_alert>;
+				cooling-device = <&CPU0 0 2>;
+				contribution = <100>;
+			};
+		};
+	};
+
 	soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -502,33 +536,14 @@
 				reg = <0x80157450 0xC>;
 			};
 
-			thermal@801573c0 {
+			thermal: thermal@801573c0 {
 				compatible = "stericsson,db8500-thermal";
 				reg = <0x801573c0 0x40>;
 				interrupt-parent = <&prcmu>;
 				interrupts = <21 IRQ_TYPE_LEVEL_HIGH>,
 					     <22 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-names = "IRQ_HOTMON_LOW", "IRQ_HOTMON_HIGH";
-				num-trips = <4>;
-
-				trip0-temp = <70000>;
-				trip0-type = "active";
-				trip0-cdev-num = <1>;
-				trip0-cdev-name0 = "thermal-cpufreq-0";
-
-				trip1-temp = <75000>;
-				trip1-type = "active";
-				trip1-cdev-num = <1>;
-				trip1-cdev-name0 = "thermal-cpufreq-0";
-
-				trip2-temp = <80000>;
-				trip2-type = "active";
-				trip2-cdev-num = <1>;
-				trip2-cdev-name0 = "thermal-cpufreq-0";
-
-				trip3-temp = <85000>;
-				trip3-type = "critical";
-				trip3-cdev-num = <0>;
+				#thermal-sensor-cells = <0>;
 			};
 
 			db8500-prcmu-regulators {
-- 
2.21.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel