Re: [PATCH v6 1/2] dt-bindings: display/bridge: Add binding for NWL mipi dsi host controller

["Guido Günther" <agx@sigxcpu.org>]

Hi,
On Mon, Sep 23, 2019 at 10:59:34AM +0200, Andrzej Hajda wrote:
> On 22.09.2019 18:47, Guido Günther wrote:
> > The Northwest Logic MIPI DSI IP core can be found in NXPs i.MX8 SoCs.
> >
> > Signed-off-by: Guido Günther <agx@sigxcpu.org>
> > Tested-by: Robert Chiras <robert.chiras@nxp.com>
> > Reviewed-by: Rob Herring <robh@kernel.org>
> > ---
> >  .../bindings/display/bridge/nwl-dsi.yaml      | 176 ++++++++++++++++++
> >  1 file changed, 176 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/display/bridge/nwl-dsi.yaml
> >
> > diff --git a/Documentation/devicetree/bindings/display/bridge/nwl-dsi.yaml b/Documentation/devicetree/bindings/display/bridge/nwl-dsi.yaml
> > new file mode 100644
> > index 000000000000..31119c7885ff
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/display/bridge/nwl-dsi.yaml
> > @@ -0,0 +1,176 @@
> > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +%YAML 1.2
> > +---
> > +$id: https://protect2.fireeye.com/url?k=7c9397fbdbbe3fd5.7c921cb4-87fc4542b5f41502&u=http://devicetree.org/schemas/display/bridge/nwl-dsi.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: Northwest Logic MIPI-DSI controller on i.MX SoCs
> > +
> > +maintainers:
> > +  - Guido Gúnther <agx@sigxcpu.org>
> > +  - Robert Chiras <robert.chiras@nxp.com>
> > +
> > +description: |
> > +  NWL MIPI-DSI host controller found on i.MX8 platforms. This is a dsi bridge for
> > +  the SOCs NWL MIPI-DSI host controller.
> > +
> > +properties:
> > +  compatible:
> > +    const: fsl,imx8mq-nwl-dsi
> > +
> > +  reg:
> > +    maxItems: 1
> > +
> > +  interrupts:
> > +    maxItems: 1
> > +
> > +  '#address-cells':
> > +    const: 1
> > +
> > +  '#size-cells':
> > +    const: 0
> > +
> > +  clocks:
> > +    items:
> > +      - description: DSI core clock
> > +      - description: RX_ESC clock (used in escape mode)
> > +      - description: TX_ESC clock (used in escape mode)
> > +      - description: PHY_REF clock
> > +
> > +  clock-names:
> > +    items:
> > +      - const: core
> > +      - const: rx_esc
> > +      - const: tx_esc
> > +      - const: phy_ref
> > +
> > +  mux-controls:
> > +    description:
> > +      mux controller node to use for operating the input mux
> > +
> > +  phys:
> > +    maxItems: 1
> > +    description:
> > +      A phandle to the phy module representing the DPHY
> > +
> > +  phy-names:
> > +    items:
> > +      - const: dphy
> > +
> > +  power-domains:
> > +    maxItems: 1
> > +
> > +  resets:
> > +    items:
> > +      - description: dsi byte reset line
> > +      - description: dsi dpi reset line
> > +      - description: dsi esc reset line
> > +      - description: dsi pclk reset line
> > +
> > +  reset-names:
> > +    items:
> > +      - const: byte
> > +      - const: dpi
> > +      - const: esc
> > +      - const: pclk
> > +
> > +  ports:
> > +    type: object
> > +    description:
> > +      A node containing DSI input & output port nodes with endpoint
> > +      definitions as documented in
> > +      Documentation/devicetree/bindings/graph.txt.
> > +    properties:
> > +      port@0:
> > +        type: object
> > +        description:
> > +          Input port node to receive pixel data from the
> > +          display controller
> > +
> > +      port@1:
> > +        type: object
> > +        description:
> > +          DSI output port node to the panel or the next bridge
> > +          in the chain
> > +
> > +      '#address-cells':
> > +        const: 1
> > +
> > +      '#size-cells':
> > +        const: 0
> > +
> > +    required:
> > +      - '#address-cells'
> > +      - '#size-cells'
> > +      - port@0
> > +      - port@1
> > +
> > +    additionalProperties: false
> > +
> > +patternProperties:
> > +  "^panel@[0-9]+$":
> > +    type: object
> > +
> > +required:
> > +  - '#address-cells'
> > +  - '#size-cells'
> > +  - clock-names
> > +  - clocks
> > +  - compatible
> > +  - interrupts
> > +  - mux-controls
> 
> 
> As I understand mux is not a part of the device, so maybe would be safer
> to make it optional.

I had mux-sel required for imx8mq *only* but Rob suggested to make things
required in general until we add other SoCs:

    https://lore.kernel.org/linux-arm-kernel/CAL_JsqK-5=WMZgNuJDTJ3Dm3YOJNw_9QCrPOOSe7MQzMV26pHw@mail.gmail.com/

Cheers,
 -- Guido

> 
> 
> Regards
> 
> Andrzej
> 
> 
> > +  - phy-names
> > +  - phys
> > +  - ports
> > +  - reg
> > +  - reset-names
> > +  - resets
> > +
> > +additionalProperties: false
> > +
> > +examples:
> > + - |
> > +
> > +   mipi_dsi: mipi_dsi@30a00000 {
> > +              #address-cells = <1>;
> > +              #size-cells = <0>;
> > +              compatible = "fsl,imx8mq-nwl-dsi";
> > +              reg = <0x30A00000 0x300>;
> > +              clocks = <&clk 163>, <&clk 244>, <&clk 245>, <&clk 164>;
> > +              clock-names = "core", "rx_esc", "tx_esc", "phy_ref";
> > +              interrupts = <0 34 4>;
> > +              mux-controls = <&mux 0>;
> > +              power-domains = <&pgc_mipi>;
> > +              resets = <&src 0>, <&src 1>, <&src 2>, <&src 3>;
> > +              reset-names = "byte", "dpi", "esc", "pclk";
> > +              phys = <&dphy>;
> > +              phy-names = "dphy";
> > +
> > +              panel@0 {
> > +                      compatible = "rocktech,jh057n00900";
> > +                      reg = <0>;
> > +                      port@0 {
> > +                           panel_in: endpoint {
> > +                                     remote-endpoint = <&mipi_dsi_out>;
> > +                           };
> > +                      };
> > +              };
> > +
> > +              ports {
> > +                    #address-cells = <1>;
> > +                    #size-cells = <0>;
> > +
> > +                    port@0 {
> > +                           reg = <0>;
> > +                           mipi_dsi_in: endpoint {
> > +                                        remote-endpoint = <&lcdif_mipi_dsi>;
> > +                           };
> > +                    };
> > +                    port@1 {
> > +                           reg = <1>;
> > +                           mipi_dsi_out: endpoint {
> > +                                         remote-endpoint = <&panel_in>;
> > +                           };
> > +                    };
> > +              };
> > +      };
> 
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel