[PATCH v2 1/3] dt-bindings: ARM: rockchip: Add Beelink A1

[PATCH v2 1/3] dt-bindings: ARM: rockchip: Add Beelink A1

[Robin Murphy]

Add a binding for the RK3328-based Beelink A1 TV box.

Signed-off-by: Robin Murphy <robin.murphy@arm.com>
---
 Documentation/devicetree/bindings/arm/rockchip.yaml | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
index c82c5e57d44c..f27f7805f57e 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@@ -40,6 +40,11 @@ properties:
           - const: asus,rk3288-tinker-s
           - const: rockchip,rk3288
 
+      - description: Beelink A1
+        items:
+          - const: azw,beelink-a1
+          - const: rockchip,rk3328
+
       - description: bq Curie 2 tablet
         items:
           - const: mundoreader,bq-curie2
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 2/3] arm64: dts: rockchip: Add RK3328 audio pipelines

[Robin Murphy]

The audio pipelines for HDMI and the analog codec are internal to the
SoC, so it makes sense to describe them at that level such that boards
need only enable the respective nodes for outputs they implement.

Signed-off-by: Robin Murphy <robin.murphy@arm.com>
---
 arch/arm64/boot/dts/rockchip/rk3328.dtsi | 32 ++++++++++++++++++++++++
 1 file changed, 32 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3328.dtsi b/arch/arm64/boot/dts/rockchip/rk3328.dtsi
index 31cc1541f1f5..91306ebed4da 100644
--- a/arch/arm64/boot/dts/rockchip/rk3328.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3328.dtsi
@@ -142,6 +142,22 @@
 		};
 	};
 
+	analog_sound: analog-sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,mclk-fs = <256>;
+		simple-audio-card,name = "Analog";
+		status = "disabled";
+
+		simple-audio-card,cpu {
+			sound-dai = <&i2s1>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&codec>;
+		};
+	};
+
 	arm-pmu {
 		compatible = "arm,cortex-a53-pmu";
 		interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
@@ -156,6 +172,22 @@
 		ports = <&vop_out>;
 	};
 
+	hdmi_sound: hdmi-sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,mclk-fs = <128>;
+		simple-audio-card,name = "HDMI";
+		status = "disabled";
+
+		simple-audio-card,cpu {
+			sound-dai = <&i2s0>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&hdmi>;
+		};
+	};
+
 	psci {
 		compatible = "arm,psci-1.0", "arm,psci-0.2";
 		method = "smc";
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 3/3] arm64: dts: rockchip: Add Beelink A1

[Robin Murphy]

Beelink A1 is a TV box implementing the higher-end options of the
RK3328 reference design - the DTB from the stock Android firmware is
clearly the "rk3328-box-plus" variant from the Rockchip 3.10 BSP with
minor modifications to accommodate the USB WiFi module and additional
VFD-style LED driver. It features:

- 4GB of 32-bit LPDDR3
- 16GB of HS200 eMMC (newer models with 32GB also exist)
- Realtek RTL8211F phy for gigabit ethernet
- Fn-Link 6221E-UUC module (RealTek RTL8821CU) for 11ac WiFi and Bluetooth 4.2
- HDMI and analog A/V
- 1x USB 3.0 type A host, 1x USB 2.0 type A OTG, 1x micro SD
- IR receiver and a neat little LED clock display.

Signed-off-by: Robin Murphy <robin.murphy@arm.com>
---
 arch/arm64/boot/dts/rockchip/Makefile      |   1 +
 arch/arm64/boot/dts/rockchip/rk3328-a1.dts | 359 +++++++++++++++++++++
 2 files changed, 360 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3328-a1.dts

diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 1f18a9392d15..a6f250e7cde2 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -1,5 +1,6 @@
 # SPDX-License-Identifier: GPL-2.0
 dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-evb.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-a1.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock64.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-roc-cc.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3328-a1.dts b/arch/arm64/boot/dts/rockchip/rk3328-a1.dts
new file mode 100644
index 000000000000..76b49f573101
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3328-a1.dts
@@ -0,0 +1,359 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+// Copyright (c) 2017-2019 Arm Ltd.
+
+/dts-v1/;
+#include "rk3328.dtsi"
+
+/ {
+	model = "Beelink A1";
+	compatible = "azw,beelink-a1", "rockchip,rk3328";
+
+	/*
+	 * UART pins, as viewed with bottom of case removed:
+	 *
+	 *           Front
+	 *        /-------
+	 *  L    / o <- Gnd
+	 *  e   / o <-- Rx
+	 *  f  / o <--- Tx
+	 *  t / o <---- +3.3v
+	 *    |
+	 */
+	chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	gmac_clkin: external-gmac-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "gmac_clkin";
+		#clock-cells = <0>;
+	};
+
+	vcc_host_5v: usb3-current-switch {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PA0 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb30_host_drv>;
+		regulator-name = "vcc_host_5v";
+		vin-supply = <&vcc_sys>;
+	};
+
+	vcc_sys: vcc-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	ir-receiver {
+		compatible = "gpio-ir-receiver";
+		gpios = <&gpio2 RK_PA2 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&analog_sound {
+	simple-audio-card,name = "Analog A/V";
+	status = "okay";
+};
+
+&codec {
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_arm>;
+};
+
+&cpu1 {
+	cpu-supply = <&vdd_arm>;
+};
+
+&cpu2 {
+	cpu-supply = <&vdd_arm>;
+};
+
+&cpu3 {
+	cpu-supply = <&vdd_arm>;
+};
+
+&emmc {
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	no-sd;
+	no-sdio;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
+	vmmc-supply = <&vcc_io>;
+	vqmmc-supply = <&vcc18_emmc>;
+	status = "okay";
+};
+
+&gmac2io {
+	assigned-clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_EXT>;
+	assigned-clock-parents = <&gmac_clkin>, <&gmac_clkin>;
+	clock_in_out = "input";
+	phy-handle = <&rtl8211f>;
+	phy-mode = "rgmii";
+	phy-supply = <&vcc_io>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmiim1_pins>;
+	snps,aal;
+	snps,pbl = <0x4>;
+	tx_delay = <0x26>;
+	rx_delay = <0x11>;
+	status = "okay";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rtl8211f: phy@0 {
+			reg = <0>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <30000>;
+			reset-gpios = <&gpio2 RK_PC1 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&gpu {
+	mali-supply = <&vdd_logic>;
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmiphy {
+	status = "okay";
+};
+
+&hdmi_sound {
+	status = "okay";
+};
+
+&i2c1 {
+	clock-frequency = <1000000>;
+	i2c-scl-falling-time-ns = <5>;
+	i2c-scl-rising-time-ns = <83>;
+	status = "okay";
+
+	pmic@18 {
+		compatible = "rockchip,rk805";
+		reg = <0x18>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <RK_PA6 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int_l>;
+		rockchip,system-power-controller;
+		wakeup-source;
+
+		vcc1-supply = <&vcc_sys>;
+		vcc2-supply = <&vcc_sys>;
+		vcc3-supply = <&vcc_sys>;
+		vcc4-supply = <&vcc_sys>;
+		vcc5-supply = <&vcc_io>;
+		vcc6-supply = <&vcc_io>;
+
+		regulators {
+			vdd_logic: DCDC_REG1 {
+				regulator-name = "vdd_logic";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vdd_arm: DCDC_REG2 {
+				regulator-name = "vdd_arm";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <950000>;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_io: DCDC_REG4 {
+				regulator-name = "vcc_io";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vdd_18: LDO_REG1 {
+				regulator-name = "vdd_18";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc18_emmc: LDO_REG2 {
+				regulator-name = "vcc_18emmc";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vdd_11: LDO_REG3 {
+				regulator-name = "vdd_11";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1100000>;
+				};
+			};
+		};
+	};
+};
+
+&i2s0 {
+	status = "okay";
+};
+
+&i2s1 {
+	status = "okay";
+};
+
+&io_domains {
+	vccio1-supply = <&vcc_io>;
+	vccio2-supply = <&vcc18_emmc>;
+	vccio3-supply = <&vcc_io>;
+	vccio4-supply = <&vdd_18>;
+	vccio5-supply = <&vcc_io>;
+	vccio6-supply = <&vdd_18>;
+	pmuio-supply = <&vcc_io>;
+	status = "okay";
+};
+
+&pinctrl {
+	pmic {
+		pmic_int_l: pmic-int-l {
+			rockchip,pins = <2 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	usb3 {
+		usb30_host_drv: usb30-host-drv {
+			rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	wifi {
+		bt_dis: bt-dis {
+			rockchip,pins = <2 RK_PC5 RK_FUNC_GPIO &pcfg_output_low>;
+		};
+
+		bt_wake_host: bt-wake-host {
+			rockchip,pins = <2 RK_PC0 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		chip_en: chip-en {
+			rockchip,pins = <2 RK_PC3 RK_FUNC_GPIO &pcfg_output_low>;
+		};
+
+		host_wake_bt: host-wake-bt {
+			rockchip,pins = <2 RK_PB7 RK_FUNC_GPIO &pcfg_output_high>;
+		};
+
+		wl_dis: wl-dis {
+			rockchip,pins = <3 RK_PB0 RK_FUNC_GPIO &pcfg_output_low>;
+		};
+
+		wl_wake_host: wl-wake-host {
+			rockchip,pins = <3 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	disable-wp;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_dectn &sdmmc0_bus4>;
+	vmmc-supply = <&vcc_io>;
+	vqmmc-supply = <&vcc_io>;
+	status = "okay";
+};
+
+&tsadc {
+	rockchip,hw-tshut-mode = <0>;
+	rockchip,hw-tshut-polarity = <0>;
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&u2phy {
+	status = "okay";
+};
+
+&u2phy_host {
+	status = "okay";
+};
+
+&u2phy_otg {
+	status = "okay";
+};
+
+&usb20_otg {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	pinctrl-names = "default";
+	pinctrl-0 = <&bt_dis &bt_wake_host &chip_en &host_wake_bt &wl_dis &wl_wake_host>;
+	status = "okay";
+};
+
+&vop {
+	status = "okay";
+};
+
+&vop_mmu {
+	status = "okay";
+};
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 1/3] dt-bindings: ARM: rockchip: Add Beelink A1

[Rob Herring]

On Mon, 14 Oct 2019 23:19:04 +0100, Robin Murphy wrote:
> Add a binding for the RK3328-based Beelink A1 TV box.
> 
> Signed-off-by: Robin Murphy <robin.murphy@arm.com>
> ---
>  Documentation/devicetree/bindings/arm/rockchip.yaml | 5 +++++
>  1 file changed, 5 insertions(+)
> 

Reviewed-by: Rob Herring <robh@kernel.org>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 1/3] dt-bindings: ARM: rockchip: Add Beelink A1

[Heiko Stübner]

Am Dienstag, 15. Oktober 2019, 00:19:04 CET schrieb Robin Murphy:
> Add a binding for the RK3328-based Beelink A1 TV box.
> 
> Signed-off-by: Robin Murphy <robin.murphy@arm.com>

applied all 3 for 5.5

Thanks
Heiko



_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel