From: megous@megous.com
To: linux-sunxi@googlegroups.com,
Kishon Vijay Abraham I <kishon@ti.com>,
Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
Maxime Ripard <mripard@kernel.org>, Chen-Yu Tsai <wens@csie.org>,
Icenowy Zheng <icenowy@aosc.io>,
Thomas Gleixner <tglx@linutronix.de>,
Arnd Bergmann <arnd@arndb.de>
Cc: Ondrej Jirman <megous@megous.com>,
devicetree@vger.kernel.org,
Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
linux-kernel@vger.kernel.org,
Paul Kocialkowski <paul.kocialkowski@bootlin.com>,
linux-arm-kernel@lists.infradead.org
Subject: [PATCH 3/4] arm64: dts: allwinner: h6: add USB3 device nodes
Date: Sun, 20 Oct 2019 15:42:28 +0200 [thread overview]
Message-ID: <20191020134229.1216351-4-megous@megous.com> (raw)
In-Reply-To: <20191020134229.1216351-1-megous@megous.com>
From: Icenowy Zheng <icenowy@aosc.io>
Allwinner H6 SoC features USB3 functionality, with a DWC3 controller and
a custom PHY.
Add device tree nodes for them.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
---
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 32 ++++++++++++++++++++
1 file changed, 32 insertions(+)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
index 0d5ea19336a1..80233db478e6 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
@@ -537,6 +537,38 @@
status = "disabled";
};
+ dwc3: dwc3@5200000 {
+ compatible = "snps,dwc3";
+ reg = <0x05200000 0x10000>;
+ interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_XHCI>,
+ <&ccu CLK_BUS_XHCI>,
+ <&rtc 0>;
+ clock-names = "ref", "bus_early", "suspend";
+ resets = <&ccu RST_BUS_XHCI>;
+ /*
+ * The datasheet of the chip doesn't declare the
+ * peripheral function, and there's no boards known
+ * to have a USB Type-B port routed to the port.
+ * In addition, no one has tested the peripheral
+ * function yet.
+ * So set the dr_mode to "host" in the DTSI file.
+ */
+ dr_mode = "host";
+ phys = <&usb3phy>;
+ phy-names = "usb3-phy";
+ status = "disabled";
+ };
+
+ usb3phy: phy@5210000 {
+ compatible = "allwinner,sun50i-h6-usb3-phy";
+ reg = <0x5210000 0x10000>;
+ clocks = <&ccu CLK_USB_PHY1>;
+ resets = <&ccu RST_USB_PHY1>;
+ #phy-cells = <0>;
+ status = "disabled";
+ };
+
ehci3: usb@5311000 {
compatible = "allwinner,sun50i-h6-ehci", "generic-ehci";
reg = <0x05311000 0x100>;
--
2.23.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2019-10-20 13:42 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-10-20 13:42 [PATCH 0/4] Add USB 3 support for H6 and Orange Pi 3 megous
2019-10-20 13:42 ` [PATCH 1/4] dt-bindings: Add bindings for USB3 phy on Allwinner H6 megous
2019-10-21 11:06 ` Maxime Ripard
2019-10-20 13:42 ` [PATCH 2/4] phy: allwinner: add phy driver for USB3 PHY on Allwinner H6 SoC megous
2019-10-21 11:08 ` Maxime Ripard
2019-11-07 20:46 ` [PATCH] phy: allwinner: Fix GENMASK misuse Rikard Falkeborn
2019-11-07 21:45 ` Ondřej Jirman
2019-11-08 11:29 ` Icenowy Zheng
2019-11-08 11:41 ` Ondřej Jirman
2019-11-08 11:43 ` Ondřej Jirman
2019-11-07 23:39 ` Russell King - ARM Linux admin
2019-11-08 1:46 ` Joe Perches
2019-11-08 8:29 ` Paul Kocialkowski
2019-11-10 12:43 ` [PATCH v2] " Rikard Falkeborn
2019-11-24 22:10 ` Rikard Falkeborn
2019-12-09 20:18 ` Rikard Falkeborn
2020-02-22 23:41 ` [PATCH v2 RESEND] " Ondrej Jirman
2020-02-23 3:23 ` [linux-sunxi] " Chen-Yu Tsai
2020-02-24 9:18 ` Maxime Ripard
2019-10-20 13:42 ` megous [this message]
2019-10-20 13:42 ` [PATCH 4/4] arm64: dts: allwinner: orange-pi-3: Enable USB 3.0 host support megous
2019-10-21 11:09 ` Maxime Ripard
2019-11-04 12:16 ` Ondřej Jirman
2019-11-05 10:45 ` Maxime Ripard
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20191020134229.1216351-4-megous@megous.com \
--to=megous@megous.com \
--cc=arnd@arndb.de \
--cc=devicetree@vger.kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=icenowy@aosc.io \
--cc=kishon@ti.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-sunxi@googlegroups.com \
--cc=mark.rutland@arm.com \
--cc=mripard@kernel.org \
--cc=paul.kocialkowski@bootlin.com \
--cc=robh+dt@kernel.org \
--cc=tglx@linutronix.de \
--cc=wens@csie.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).