From: Dinh Nguyen <dinguyen@kernel.org>
To: devicetree@vger.kernel.org
Cc: mark.rutland@arm.com, dinguyen@kernel.org, robh+dt@kernel.org,
Dinh Nguyen <dinh.nguyen@intel.com>,
linux-arm-kernel@lists.infradead.org
Subject: [PATCH 2/2] arm64: dts: add NAND board files for Stratix10 and Agilex
Date: Fri, 8 Nov 2019 10:33:27 -0600 [thread overview]
Message-ID: <20191108163327.2917-2-dinguyen@kernel.org> (raw)
In-Reply-To: <20191108163327.2917-1-dinguyen@kernel.org>
From: Dinh Nguyen <dinh.nguyen@intel.com>
The Stratix10 and Agilex devkits support a separate NAND daughter card.
The NAND daughter card replaces the SDMMC slot that is on the default
daughter card thus requires a separate board dts file.
add socfpga_agilex_socdk_nand.dts
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
---
arch/arm64/boot/dts/altera/Makefile | 3 +-
.../altera/socfpga_stratix10_socdk_nand.dts | 225 ++++++++++++++++++
arch/arm64/boot/dts/intel/Makefile | 3 +-
.../dts/intel/socfpga_agilex_socdk_nand.dts | 136 +++++++++++
4 files changed, 365 insertions(+), 2 deletions(-)
create mode 100644 arch/arm64/boot/dts/altera/socfpga_stratix10_socdk_nand.dts
create mode 100644 arch/arm64/boot/dts/intel/socfpga_agilex_socdk_nand.dts
diff --git a/arch/arm64/boot/dts/altera/Makefile b/arch/arm64/boot/dts/altera/Makefile
index 27bb925adc8d..10119c7ab437 100644
--- a/arch/arm64/boot/dts/altera/Makefile
+++ b/arch/arm64/boot/dts/altera/Makefile
@@ -1,2 +1,3 @@
# SPDX-License-Identifier: GPL-2.0-only
-dtb-$(CONFIG_ARCH_STRATIX10) += socfpga_stratix10_socdk.dtb
+dtb-$(CONFIG_ARCH_STRATIX10) += socfpga_stratix10_socdk.dtb \
+ socfpga_stratix10_socdk_nand.dtb
diff --git a/arch/arm64/boot/dts/altera/socfpga_stratix10_socdk_nand.dts b/arch/arm64/boot/dts/altera/socfpga_stratix10_socdk_nand.dts
new file mode 100644
index 000000000000..d18f894373b4
--- /dev/null
+++ b/arch/arm64/boot/dts/altera/socfpga_stratix10_socdk_nand.dts
@@ -0,0 +1,225 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright Altera Corporation (C) 2015. All rights reserved.
+ */
+
+#include "socfpga_stratix10.dtsi"
+
+/ {
+ model = "SoCFPGA Stratix 10 SoCDK";
+
+ aliases {
+ serial0 = &uart0;
+ ethernet0 = &gmac0;
+ ethernet1 = &gmac1;
+ ethernet2 = &gmac2;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ hps0 {
+ label = "hps_led0";
+ gpios = <&portb 20 GPIO_ACTIVE_HIGH>;
+ };
+
+ hps1 {
+ label = "hps_led1";
+ gpios = <&portb 19 GPIO_ACTIVE_HIGH>;
+ };
+
+ hps2 {
+ label = "hps_led2";
+ gpios = <&portb 21 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ /* We expect the bootloader to fill in the reg */
+ reg = <0 0 0 0>;
+ };
+
+ ref_033v: 033-v-ref {
+ compatible = "regulator-fixed";
+ regulator-name = "0.33V";
+ regulator-min-microvolt = <330000>;
+ regulator-max-microvolt = <330000>;
+ };
+
+ soc {
+ clocks {
+ osc1 {
+ clock-frequency = <25000000>;
+ };
+ };
+
+ eccmgr {
+ sdmmca-ecc@ff8c8c00 {
+ compatible = "altr,socfpga-s10-sdmmc-ecc",
+ "altr,socfpga-sdmmc-ecc";
+ reg = <0xff8c8c00 0x100>;
+ altr,ecc-parent = <&mmc>;
+ interrupts = <14 4>,
+ <15 4>;
+ };
+ };
+ };
+};
+
+&gpio1 {
+ status = "okay";
+};
+
+&gmac0 {
+ status = "okay";
+ phy-mode = "rgmii";
+ phy-handle = <&phy0>;
+
+ max-frame-size = <9000>;
+
+ mdio0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "snps,dwmac-mdio";
+ phy0: ethernet-phy@0 {
+ reg = <4>;
+
+ txd0-skew-ps = <0>; /* -420ps */
+ txd1-skew-ps = <0>; /* -420ps */
+ txd2-skew-ps = <0>; /* -420ps */
+ txd3-skew-ps = <0>; /* -420ps */
+ rxd0-skew-ps = <420>; /* 0ps */
+ rxd1-skew-ps = <420>; /* 0ps */
+ rxd2-skew-ps = <420>; /* 0ps */
+ rxd3-skew-ps = <420>; /* 0ps */
+ txen-skew-ps = <0>; /* -420ps */
+ txc-skew-ps = <900>; /* 0ps */
+ rxdv-skew-ps = <420>; /* 0ps */
+ rxc-skew-ps = <1680>; /* 780ps */
+ };
+ };
+};
+
+&nand {
+ status = "okay";
+ nand-bus-width = <16>;
+
+ flash@0 {
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0 0x200000>;
+ };
+
+ partition@200000 {
+ label = "env";
+ reg = <0x200000 0x40000>;
+ };
+
+ partition@240000 {
+ label = "dtb";
+ reg = <0x240000 0x40000>;
+ };
+
+ partition@280000 {
+ label = "kernel";
+ reg = <0x280000 0x2000000>;
+ };
+
+ partition@2280000 {
+ label = "misc";
+ reg = <0x2280000 0x2000000>;
+ };
+
+ partition@4280000 {
+ label = "rootfs";
+ reg = <0x4280000 0x3bd0000>;
+ };
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+ disable-over-current;
+};
+
+&watchdog0 {
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+ clock-frequency = <100000>;
+ i2c-sda-falling-time-ns = <890>; /* hcnt */
+ i2c-sdl-falling-time-ns = <890>; /* lcnt */
+
+ adc@14 {
+ compatible = "lltc,ltc2497";
+ reg = <0x14>;
+ vref-supply = <&ref_033v>;
+ };
+
+ temp@4c {
+ compatible = "maxim,max1619";
+ reg = <0x4c>;
+ };
+
+ eeprom@51 {
+ compatible = "atmel,24c32";
+ reg = <0x51>;
+ pagesize = <32>;
+ };
+
+ rtc@68 {
+ compatible = "dallas,ds1339";
+ reg = <0x68>;
+ };
+};
+
+&qspi {
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "n25q00a";
+ reg = <0>;
+ spi-max-frequency = <100000000>;
+
+ m25p,fast-read;
+ cdns,page-size = <256>;
+ cdns,block-size = <16>;
+ cdns,read-delay = <1>;
+ cdns,tshsl-ns = <50>;
+ cdns,tsd2d-ns = <50>;
+ cdns,tchsh-ns = <4>;
+ cdns,tslch-ns = <4>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ qspi_boot: partition@0 {
+ label = "Boot and fpga data";
+ reg = <0x0 0x034B0000>;
+ };
+
+ qspi_rootfs: partition@4000000 {
+ label = "Root Filesystem - JFFS2";
+ reg = <0x034B0000 0x0EB50000>;
+ };
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/intel/Makefile b/arch/arm64/boot/dts/intel/Makefile
index 1253af30da8e..40cb16e8c814 100644
--- a/arch/arm64/boot/dts/intel/Makefile
+++ b/arch/arm64/boot/dts/intel/Makefile
@@ -1,2 +1,3 @@
# SPDX-License-Identifier: GPL-2.0-only
-dtb-$(CONFIG_ARCH_AGILEX) += socfpga_agilex_socdk.dtb
+dtb-$(CONFIG_ARCH_AGILEX) += socfpga_agilex_socdk.dtb \
+ socfpga_agilex_socdk_nand.dtb
diff --git a/arch/arm64/boot/dts/intel/socfpga_agilex_socdk_nand.dts b/arch/arm64/boot/dts/intel/socfpga_agilex_socdk_nand.dts
new file mode 100644
index 000000000000..90618881854a
--- /dev/null
+++ b/arch/arm64/boot/dts/intel/socfpga_agilex_socdk_nand.dts
@@ -0,0 +1,136 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2019, Intel Corporation
+ */
+#include "socfpga_agilex.dtsi"
+
+/ {
+ model = "SoCFPGA Agilex SoCDK";
+
+ aliases {
+ serial0 = &uart0;
+ ethernet0 = &gmac0;
+ ethernet1 = &gmac1;
+ ethernet2 = &gmac2;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ hps0 {
+ label = "hps_led0";
+ gpios = <&portb 20 GPIO_ACTIVE_HIGH>;
+ };
+
+ hps1 {
+ label = "hps_led1";
+ gpios = <&portb 19 GPIO_ACTIVE_HIGH>;
+ };
+
+ hps2 {
+ label = "hps_led2";
+ gpios = <&portb 21 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ /* We expect the bootloader to fill in the reg */
+ reg = <0 0 0 0>;
+ };
+
+ soc {
+ clocks {
+ osc1 {
+ clock-frequency = <25000000>;
+ };
+ };
+ };
+};
+
+&gpio1 {
+ status = "okay";
+};
+
+&gmac0 {
+ status = "okay";
+ phy-mode = "rgmii";
+ phy-handle = <&phy0>;
+
+ max-frame-size = <9000>;
+
+ mdio0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "snps,dwmac-mdio";
+ phy0: ethernet-phy@0 {
+ reg = <4>;
+
+ txd0-skew-ps = <0>; /* -420ps */
+ txd1-skew-ps = <0>; /* -420ps */
+ txd2-skew-ps = <0>; /* -420ps */
+ txd3-skew-ps = <0>; /* -420ps */
+ rxd0-skew-ps = <420>; /* 0ps */
+ rxd1-skew-ps = <420>; /* 0ps */
+ rxd2-skew-ps = <420>; /* 0ps */
+ rxd3-skew-ps = <420>; /* 0ps */
+ txen-skew-ps = <0>; /* -420ps */
+ txc-skew-ps = <900>; /* 0ps */
+ rxdv-skew-ps = <420>; /* 0ps */
+ rxc-skew-ps = <1680>; /* 780ps */
+ };
+ };
+};
+
+&nand {
+ status = "okay";
+ nand-bus-width = <16>;
+
+ flash@0 {
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ partition@0 {
+ label = "u-boot";
+ reg = <0 0x200000>;
+ };
+ partition@200000 {
+ label = "env";
+ reg = <0x200000 0x40000>;
+ };
+ partition@240000 {
+ label = "dtb";
+ reg = <0x240000 0x40000>;
+ };
+ partition@280000 {
+ label = "kernel";
+ reg = <0x280000 0x2000000>;
+ };
+ partition@2280000 {
+ label = "misc";
+ reg = <0x2280000 0x2000000>;
+ };
+ partition@4280000 {
+ label = "rootfs";
+ reg = <0x4280000 0x3bd0000>;
+ };
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+ disable-over-current;
+};
+
+&watchdog0 {
+ status = "okay";
+};
--
2.20.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
prev parent reply other threads:[~2019-11-08 16:34 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-11-08 16:33 [PATCH 1/2] arm64: dts: agilex: add NAND IP to base dts Dinh Nguyen
2019-11-08 16:33 ` Dinh Nguyen [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20191108163327.2917-2-dinguyen@kernel.org \
--to=dinguyen@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=dinh.nguyen@intel.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).