Linux-ARM-Kernel Archive on lore.kernel.org
 help / color / Atom feed
* [PATCH 1/2] arm64: dts: agilex: add NAND IP to base dts
@ 2019-11-08 16:33 Dinh Nguyen
  2019-11-08 16:33 ` [PATCH 2/2] arm64: dts: add NAND board files for Stratix10 and Agilex Dinh Nguyen
  0 siblings, 1 reply; 2+ messages in thread
From: Dinh Nguyen @ 2019-11-08 16:33 UTC (permalink / raw)
  To: devicetree; +Cc: mark.rutland, dinguyen, robh+dt, linux-arm-kernel

Add NAND entry to base DTSI.

Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
---
 arch/arm64/boot/dts/intel/socfpga_agilex.dtsi | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm64/boot/dts/intel/socfpga_agilex.dtsi b/arch/arm64/boot/dts/intel/socfpga_agilex.dtsi
index 94090c6fb946..f9565e76a9d1 100644
--- a/arch/arm64/boot/dts/intel/socfpga_agilex.dtsi
+++ b/arch/arm64/boot/dts/intel/socfpga_agilex.dtsi
@@ -249,6 +249,18 @@
 			status = "disabled";
 		};
 
+		nand: nand@ffb90000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "altr,socfpga-denali-nand";
+			reg = <0xffb90000 0x10000>,
+			      <0xffb80000 0x1000>;
+			reg-names = "nand_data", "denali_reg";
+			interrupts = <0 97 4>;
+			resets = <&rst NAND_RESET>, <&rst NAND_OCP_RESET>;
+			status = "disabled";
+		};
+
 		ocram: sram@ffe00000 {
 			compatible = "mmio-sram";
 			reg = <0xffe00000 0x40000>;
-- 
2.20.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 2+ messages in thread

* [PATCH 2/2] arm64: dts: add NAND board files for Stratix10 and Agilex
  2019-11-08 16:33 [PATCH 1/2] arm64: dts: agilex: add NAND IP to base dts Dinh Nguyen
@ 2019-11-08 16:33 ` Dinh Nguyen
  0 siblings, 0 replies; 2+ messages in thread
From: Dinh Nguyen @ 2019-11-08 16:33 UTC (permalink / raw)
  To: devicetree; +Cc: mark.rutland, dinguyen, robh+dt, Dinh Nguyen, linux-arm-kernel

From: Dinh Nguyen <dinh.nguyen@intel.com>

The Stratix10 and Agilex devkits support a separate NAND daughter card.
The NAND daughter card replaces the SDMMC slot that is on the default
daughter card thus requires a separate board dts file.

add socfpga_agilex_socdk_nand.dts

Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
---
 arch/arm64/boot/dts/altera/Makefile           |   3 +-
 .../altera/socfpga_stratix10_socdk_nand.dts   | 225 ++++++++++++++++++
 arch/arm64/boot/dts/intel/Makefile            |   3 +-
 .../dts/intel/socfpga_agilex_socdk_nand.dts   | 136 +++++++++++
 4 files changed, 365 insertions(+), 2 deletions(-)
 create mode 100644 arch/arm64/boot/dts/altera/socfpga_stratix10_socdk_nand.dts
 create mode 100644 arch/arm64/boot/dts/intel/socfpga_agilex_socdk_nand.dts

diff --git a/arch/arm64/boot/dts/altera/Makefile b/arch/arm64/boot/dts/altera/Makefile
index 27bb925adc8d..10119c7ab437 100644
--- a/arch/arm64/boot/dts/altera/Makefile
+++ b/arch/arm64/boot/dts/altera/Makefile
@@ -1,2 +1,3 @@
 # SPDX-License-Identifier: GPL-2.0-only
-dtb-$(CONFIG_ARCH_STRATIX10) += socfpga_stratix10_socdk.dtb
+dtb-$(CONFIG_ARCH_STRATIX10) += socfpga_stratix10_socdk.dtb \
+				socfpga_stratix10_socdk_nand.dtb
diff --git a/arch/arm64/boot/dts/altera/socfpga_stratix10_socdk_nand.dts b/arch/arm64/boot/dts/altera/socfpga_stratix10_socdk_nand.dts
new file mode 100644
index 000000000000..d18f894373b4
--- /dev/null
+++ b/arch/arm64/boot/dts/altera/socfpga_stratix10_socdk_nand.dts
@@ -0,0 +1,225 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright Altera Corporation (C) 2015. All rights reserved.
+ */
+
+#include "socfpga_stratix10.dtsi"
+
+/ {
+	model = "SoCFPGA Stratix 10 SoCDK";
+
+	aliases {
+		serial0 = &uart0;
+		ethernet0 = &gmac0;
+		ethernet1 = &gmac1;
+		ethernet2 = &gmac2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		hps0 {
+			label = "hps_led0";
+			gpios = <&portb 20 GPIO_ACTIVE_HIGH>;
+		};
+
+		hps1 {
+			label = "hps_led1";
+			gpios = <&portb 19 GPIO_ACTIVE_HIGH>;
+		};
+
+		hps2 {
+			label = "hps_led2";
+			gpios = <&portb 21 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		/* We expect the bootloader to fill in the reg */
+		reg = <0 0 0 0>;
+	};
+
+	ref_033v: 033-v-ref {
+		compatible = "regulator-fixed";
+		regulator-name = "0.33V";
+		regulator-min-microvolt = <330000>;
+		regulator-max-microvolt = <330000>;
+	};
+
+	soc {
+		clocks {
+			osc1 {
+				clock-frequency = <25000000>;
+			};
+		};
+
+		eccmgr {
+			sdmmca-ecc@ff8c8c00 {
+				compatible = "altr,socfpga-s10-sdmmc-ecc",
+					     "altr,socfpga-sdmmc-ecc";
+				reg = <0xff8c8c00 0x100>;
+				altr,ecc-parent = <&mmc>;
+				interrupts = <14 4>,
+					     <15 4>;
+			};
+		};
+	};
+};
+
+&gpio1 {
+	status = "okay";
+};
+
+&gmac0 {
+	status = "okay";
+	phy-mode = "rgmii";
+	phy-handle = <&phy0>;
+
+	max-frame-size = <9000>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy0: ethernet-phy@0 {
+			reg = <4>;
+
+			txd0-skew-ps = <0>; /* -420ps */
+			txd1-skew-ps = <0>; /* -420ps */
+			txd2-skew-ps = <0>; /* -420ps */
+			txd3-skew-ps = <0>; /* -420ps */
+			rxd0-skew-ps = <420>; /* 0ps */
+			rxd1-skew-ps = <420>; /* 0ps */
+			rxd2-skew-ps = <420>; /* 0ps */
+			rxd3-skew-ps = <420>; /* 0ps */
+			txen-skew-ps = <0>; /* -420ps */
+			txc-skew-ps = <900>; /* 0ps */
+			rxdv-skew-ps = <420>; /* 0ps */
+			rxc-skew-ps = <1680>; /* 780ps */
+		};
+	};
+};
+
+&nand {
+	status = "okay";
+	nand-bus-width = <16>;
+
+	flash@0 {
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "u-boot";
+				reg = <0 0x200000>;
+			};
+
+			partition@200000 {
+				label = "env";
+				reg = <0x200000 0x40000>;
+			};
+
+			partition@240000 {
+				label = "dtb";
+				reg = <0x240000 0x40000>;
+			};
+
+			partition@280000 {
+				label = "kernel";
+				reg = <0x280000 0x2000000>;
+			};
+
+			partition@2280000 {
+				label = "misc";
+				reg = <0x2280000 0x2000000>;
+			};
+
+			partition@4280000 {
+				label = "rootfs";
+				reg = <0x4280000 0x3bd0000>;
+			};
+		};
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+	disable-over-current;
+};
+
+&watchdog0 {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+	clock-frequency = <100000>;
+	i2c-sda-falling-time-ns = <890>;  /* hcnt */
+	i2c-sdl-falling-time-ns = <890>;  /* lcnt */
+
+	adc@14 {
+		compatible = "lltc,ltc2497";
+		reg = <0x14>;
+		vref-supply = <&ref_033v>;
+	};
+
+	temp@4c {
+		compatible = "maxim,max1619";
+		reg = <0x4c>;
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c32";
+		reg = <0x51>;
+		pagesize = <32>;
+	};
+
+	rtc@68 {
+		compatible = "dallas,ds1339";
+		reg = <0x68>;
+	};
+};
+
+&qspi {
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "n25q00a";
+		reg = <0>;
+		spi-max-frequency = <100000000>;
+
+		m25p,fast-read;
+		cdns,page-size = <256>;
+		cdns,block-size = <16>;
+		cdns,read-delay = <1>;
+		cdns,tshsl-ns = <50>;
+		cdns,tsd2d-ns = <50>;
+		cdns,tchsh-ns = <4>;
+		cdns,tslch-ns = <4>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			qspi_boot: partition@0 {
+				label = "Boot and fpga data";
+				reg = <0x0 0x034B0000>;
+			};
+
+			qspi_rootfs: partition@4000000 {
+				label = "Root Filesystem - JFFS2";
+				reg = <0x034B0000 0x0EB50000>;
+			};
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/intel/Makefile b/arch/arm64/boot/dts/intel/Makefile
index 1253af30da8e..40cb16e8c814 100644
--- a/arch/arm64/boot/dts/intel/Makefile
+++ b/arch/arm64/boot/dts/intel/Makefile
@@ -1,2 +1,3 @@
 # SPDX-License-Identifier: GPL-2.0-only
-dtb-$(CONFIG_ARCH_AGILEX) += socfpga_agilex_socdk.dtb
+dtb-$(CONFIG_ARCH_AGILEX) += socfpga_agilex_socdk.dtb \
+			     socfpga_agilex_socdk_nand.dtb
diff --git a/arch/arm64/boot/dts/intel/socfpga_agilex_socdk_nand.dts b/arch/arm64/boot/dts/intel/socfpga_agilex_socdk_nand.dts
new file mode 100644
index 000000000000..90618881854a
--- /dev/null
+++ b/arch/arm64/boot/dts/intel/socfpga_agilex_socdk_nand.dts
@@ -0,0 +1,136 @@
+// SPDX-License-Identifier:     GPL-2.0
+/*
+ * Copyright (C) 2019, Intel Corporation
+ */
+#include "socfpga_agilex.dtsi"
+
+/ {
+	model = "SoCFPGA Agilex SoCDK";
+
+	aliases {
+		serial0 = &uart0;
+		ethernet0 = &gmac0;
+		ethernet1 = &gmac1;
+		ethernet2 = &gmac2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		hps0 {
+			label = "hps_led0";
+			gpios = <&portb 20 GPIO_ACTIVE_HIGH>;
+		};
+
+		hps1 {
+			label = "hps_led1";
+			gpios = <&portb 19 GPIO_ACTIVE_HIGH>;
+		};
+
+		hps2 {
+			label = "hps_led2";
+			gpios = <&portb 21 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		/* We expect the bootloader to fill in the reg */
+		reg = <0 0 0 0>;
+	};
+
+	soc {
+		clocks {
+			osc1 {
+				clock-frequency = <25000000>;
+			};
+		};
+	};
+};
+
+&gpio1 {
+	status = "okay";
+};
+
+&gmac0 {
+	status = "okay";
+	phy-mode = "rgmii";
+	phy-handle = <&phy0>;
+
+	max-frame-size = <9000>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy0: ethernet-phy@0 {
+			reg = <4>;
+
+			txd0-skew-ps = <0>; /* -420ps */
+			txd1-skew-ps = <0>; /* -420ps */
+			txd2-skew-ps = <0>; /* -420ps */
+			txd3-skew-ps = <0>; /* -420ps */
+			rxd0-skew-ps = <420>; /* 0ps */
+			rxd1-skew-ps = <420>; /* 0ps */
+			rxd2-skew-ps = <420>; /* 0ps */
+			rxd3-skew-ps = <420>; /* 0ps */
+			txen-skew-ps = <0>; /* -420ps */
+			txc-skew-ps = <900>; /* 0ps */
+			rxdv-skew-ps = <420>; /* 0ps */
+			rxc-skew-ps = <1680>; /* 780ps */
+		};
+	};
+};
+
+&nand {
+	status = "okay";
+	nand-bus-width = <16>;
+
+	flash@0 {
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			partition@0 {
+				label = "u-boot";
+				reg = <0 0x200000>;
+			};
+			partition@200000 {
+				label = "env";
+				reg = <0x200000 0x40000>;
+			};
+			partition@240000 {
+				label = "dtb";
+				reg = <0x240000 0x40000>;
+			};
+			partition@280000 {
+				label = "kernel";
+				reg = <0x280000 0x2000000>;
+			};
+			partition@2280000 {
+				label = "misc";
+				reg = <0x2280000 0x2000000>;
+			};
+			partition@4280000 {
+				label = "rootfs";
+				reg = <0x4280000 0x3bd0000>;
+			};
+		};
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+	disable-over-current;
+};
+
+&watchdog0 {
+	status = "okay";
+};
-- 
2.20.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 2+ messages in thread

end of thread, back to index

Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-11-08 16:33 [PATCH 1/2] arm64: dts: agilex: add NAND IP to base dts Dinh Nguyen
2019-11-08 16:33 ` [PATCH 2/2] arm64: dts: add NAND board files for Stratix10 and Agilex Dinh Nguyen

Linux-ARM-Kernel Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-arm-kernel/0 linux-arm-kernel/git/0.git
	git clone --mirror https://lore.kernel.org/linux-arm-kernel/1 linux-arm-kernel/git/1.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-arm-kernel linux-arm-kernel/ https://lore.kernel.org/linux-arm-kernel \
		linux-arm-kernel@lists.infradead.org
	public-inbox-index linux-arm-kernel

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.infradead.lists.linux-arm-kernel


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git