* [PATCH v2 0/2] Add mt8173 elm and hana board
@ 2020-01-10 7:37 Hsin-Yi Wang
2020-01-10 7:37 ` [PATCH v2 1/2] dt-bindings: arm64: dts: mediatek: Add mt8173 elm and hana Hsin-Yi Wang
2020-01-10 7:37 ` [PATCH v2 2/2] arm64: dts: mediatek: add mt8173 elm and hana board Hsin-Yi Wang
0 siblings, 2 replies; 14+ messages in thread
From: Hsin-Yi Wang @ 2020-01-10 7:37 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Mark Rutland, devicetree, Nicolas Boichat, linux-kernel,
Daniel Kurtz, Enric Balletbo i Serra, Rob Herring,
linux-mediatek, Matthias Brugger
This series adds devicetree and binding document for Acer Chromebook R13 (elm)
and Lenovo Chromebook (hana), which are using mt8173 as SoC.
Changes in v2:
- fix mediatek.yaml
- fixup some nodes and remove unused nodes in dts
Hsin-Yi Wang (2):
dt-bindings: arm64: dts: mediatek: Add mt8173 elm and hana
arm64: dts: mediatek: add mt8173 elm and hana board
.../devicetree/bindings/arm/mediatek.yaml | 27 +
arch/arm64/boot/dts/mediatek/Makefile | 3 +
.../dts/mediatek/mt8173-elm-hana-rev7.dts | 27 +
.../boot/dts/mediatek/mt8173-elm-hana.dts | 16 +
.../boot/dts/mediatek/mt8173-elm-hana.dtsi | 60 +
arch/arm64/boot/dts/mediatek/mt8173-elm.dts | 15 +
arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi | 1040 +++++++++++++++++
7 files changed, 1188 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dtsi
create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi
--
2.25.0.rc1.283.g88dfdc4193-goog
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v2 1/2] dt-bindings: arm64: dts: mediatek: Add mt8173 elm and hana
2020-01-10 7:37 [PATCH v2 0/2] Add mt8173 elm and hana board Hsin-Yi Wang
@ 2020-01-10 7:37 ` Hsin-Yi Wang
2020-01-10 11:38 ` Enric Balletbo i Serra
2020-01-15 14:52 ` Rob Herring
2020-01-10 7:37 ` [PATCH v2 2/2] arm64: dts: mediatek: add mt8173 elm and hana board Hsin-Yi Wang
1 sibling, 2 replies; 14+ messages in thread
From: Hsin-Yi Wang @ 2020-01-10 7:37 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Mark Rutland, devicetree, Nicolas Boichat, linux-kernel,
Daniel Kurtz, Enric Balletbo i Serra, Rob Herring,
linux-mediatek, Matthias Brugger
Elm is Acer Chromebook R13. Hana is Lenovo Chromebook. Both uses mt8173
SoC.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
---
Changes in v2:
- fix dtbs_check errors, use const instead of enum
---
.../devicetree/bindings/arm/mediatek.yaml | 27 +++++++++++++++++++
1 file changed, 27 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/mediatek.yaml b/Documentation/devicetree/bindings/arm/mediatek.yaml
index 4043c5046441..5272899b08fa 100644
--- a/Documentation/devicetree/bindings/arm/mediatek.yaml
+++ b/Documentation/devicetree/bindings/arm/mediatek.yaml
@@ -84,6 +84,33 @@ properties:
- enum:
- mediatek,mt8135-evbp1
- const: mediatek,mt8135
+ - description: Google Elm (Acer Chromebook R13)
+ items:
+ - const: google,elm-rev8
+ - const: google,elm-rev7
+ - const: google,elm-rev6
+ - const: google,elm-rev5
+ - const: google,elm-rev4
+ - const: google,elm-rev3
+ - const: google,elm-rev2
+ - const: google,elm-rev1
+ - const: google,elm
+ - const: mediatek,mt8173
+ - description: Google Hana (Lenovo Chromebook and more)
+ items:
+ - const: google,hana-rev6
+ - const: google,hana-rev5
+ - const: google,hana-rev4
+ - const: google,hana-rev3
+ - const: google,hana-rev2
+ - const: google,hana-rev1
+ - const: google,hana-rev0
+ - const: google,hana
+ - const: mediatek,mt8173
+ - description: Google Hana rev7 (Poin2 Chromebook 11C)
+ items:
+ - const: google,hana-rev7
+ - const: mediatek,mt8173
- items:
- enum:
- mediatek,mt8173-evb
--
2.25.0.rc1.283.g88dfdc4193-goog
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v2 2/2] arm64: dts: mediatek: add mt8173 elm and hana board
2020-01-10 7:37 [PATCH v2 0/2] Add mt8173 elm and hana board Hsin-Yi Wang
2020-01-10 7:37 ` [PATCH v2 1/2] dt-bindings: arm64: dts: mediatek: Add mt8173 elm and hana Hsin-Yi Wang
@ 2020-01-10 7:37 ` Hsin-Yi Wang
2020-01-10 8:52 ` Yingjoe Chen
` (2 more replies)
1 sibling, 3 replies; 14+ messages in thread
From: Hsin-Yi Wang @ 2020-01-10 7:37 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Mark Rutland, devicetree, Nicolas Boichat, linux-kernel,
Daniel Kurtz, Enric Balletbo i Serra, Rob Herring,
linux-mediatek, Matthias Brugger
Elm is Acer Chromebook R13. Hana is Lenovo Chromebook. Both uses mt8173
SoC.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
---
Changes in v2:
- remove downstream nodes and unused nodes
- use GPIO_ACTIVE_LOW for ps8640 gpios
- move trackpad to hana
---
arch/arm64/boot/dts/mediatek/Makefile | 3 +
.../dts/mediatek/mt8173-elm-hana-rev7.dts | 27 +
.../boot/dts/mediatek/mt8173-elm-hana.dts | 16 +
.../boot/dts/mediatek/mt8173-elm-hana.dtsi | 60 +
arch/arm64/boot/dts/mediatek/mt8173-elm.dts | 15 +
arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi | 1040 +++++++++++++++++
6 files changed, 1161 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dtsi
create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi
diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 458bbc422a94..b45a45a565a1 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -6,5 +6,8 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana-rev7.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-evb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-evb.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts
new file mode 100644
index 000000000000..a3616bc3d859
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts
@@ -0,0 +1,27 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2019 MediaTek Inc.
+ */
+
+/dts-v1/;
+#include "mt8173-elm-hana.dtsi"
+
+/ {
+ model = "Mediatek Hana rev7 board";
+ compatible = "google,hana-rev7", "mediatek,mt8173";
+};
+
+&cpu_thermal {
+ trips {
+ cpu_crit: cpu_crit@0 {
+ temperature = <100000>;
+ type = "critical";
+ };
+ };
+};
+
+&gpio_keys {
+ /delete-node/tablet_mode;
+ /delete-node/volume_down;
+ /delete-node/volume_up;
+};
\ No newline at end of file
diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts
new file mode 100644
index 000000000000..8cbcc75192e3
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2016 MediaTek Inc.
+ */
+
+/dts-v1/;
+#include "mt8173-elm-hana.dtsi"
+
+/ {
+ model = "Mediatek Hana rev0 board";
+ compatible = "google,hana-rev6",
+ "google,hana-rev5", "google,hana-rev4",
+ "google,hana-rev3", "google,hana-rev2",
+ "google,hana-rev1", "google,hana-rev0",
+ "google,hana", "mediatek,mt8173";
+};
\ No newline at end of file
diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dtsi b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dtsi
new file mode 100644
index 000000000000..35e12b290947
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dtsi
@@ -0,0 +1,60 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2016 MediaTek Inc.
+ */
+
+#include "mt8173-elm.dtsi"
+
+&i2c0 {
+ clock-frequency = <200000>;
+};
+
+&i2c3 {
+ touchscreen2: touchscreen@34 {
+ compatible = "melfas,mip4_ts";
+ reg = <0x34>;
+ interrupt-parent = <&pio>;
+ interrupts = <88 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ touchscreen3: touchscreen@20 {
+ compatible = "hid-over-i2c";
+ reg = <0x20>;
+ hid-descr-addr = <0x0020>;
+ interrupt-parent = <&pio>;
+ interrupts = <88 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&i2c4 {
+ trackpad2: trackpad@2c {
+ compatible = "hid-over-i2c";
+ interrupt-parent = <&pio>;
+ interrupts = <117 IRQ_TYPE_LEVEL_LOW>;
+ reg = <0x2c>;
+ hid-descr-addr = <0x0020>;
+ wakeup-source;
+ };
+};
+
+&mmc1 {
+ wp-gpios = <&pio 42 GPIO_ACTIVE_HIGH>;
+};
+
+&pio {
+ hdmi_mux_pins: hdmi_mux_pins {
+ pins2 {
+ pinmux = <MT8173_PIN_98_URTS1__FUNC_GPIO98>;
+ bias-pull-up;
+ output-high;
+ };
+ };
+
+ mmc1_pins_default: mmc1default {
+ pins_wp {
+ pinmux = <MT8173_PIN_42_DSI_TE__FUNC_GPIO42>;
+ input-enable;
+ bias-pull-up;
+ };
+ };
+};
\ No newline at end of file
diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm.dts b/arch/arm64/boot/dts/mediatek/mt8173-elm.dts
new file mode 100644
index 000000000000..e5da2355760e
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8173-elm.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2016 MediaTek Inc.
+ */
+
+/dts-v1/;
+#include "mt8173-elm.dtsi"
+
+/ {
+ model = "Mediatek Elm board";
+ compatible = "google,elm-rev8", "google,elm-rev7", "google,elm-rev6",
+ "google,elm-rev5", "google,elm-rev4", "google,elm-rev3",
+ "google,elm-rev2", "google,elm-rev1",
+ "google,elm", "mediatek,mt8173";
+};
\ No newline at end of file
diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi b/arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi
new file mode 100644
index 000000000000..2ac738bebe04
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi
@@ -0,0 +1,1040 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2016 MediaTek Inc.
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "mt8173.dtsi"
+
+/ {
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart1;
+ serial2 = &uart2;
+ serial3 = &uart3;
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ reg = <0 0x40000000 0 0x80000000>;
+ };
+
+ backlight_lcd: backlight_lcd {
+ compatible = "pwm-backlight";
+ pwms = <&pwm0 0 1000000>;
+ brightness-levels = <
+ 0 16 32 48 64 80 96 112
+ 128 144 160 176 192 208 224 240
+ 255
+ >;
+ default-brightness-level = <9>;
+ power-supply = <&bl_fixed_reg>;
+ enable-gpios = <&pio 95 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&disp_pwm0_pins>;
+ status = "okay";
+ };
+
+ bl_fixed_reg: fixedregulator@2 {
+ compatible = "regulator-fixed";
+ regulator-name = "bl_fixed";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ startup-delay-us = <1000>;
+ enable-active-high;
+ gpio = <&pio 32 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&bl_fixed_pins>;
+ };
+
+ chosen {
+ stdout-path = &uart0;
+ };
+
+ gpio_keys: gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_keys_pins>;
+
+ lid {
+ label = "Lid";
+ gpios = <&pio 69 GPIO_ACTIVE_LOW>;
+ linux,code = <0>; /* SW_LID */
+ linux,input-type = <5>; /* EV_SW */
+ gpio-key,wakeup;
+ };
+
+ power {
+ label = "Power";
+ gpios = <&pio 14 GPIO_ACTIVE_HIGH>;
+ linux,code = <KEY_POWER>;
+ debounce-interval = <30>;
+ gpio-key,wakeup;
+ };
+
+ tablet_mode {
+ label = "Tablet_mode";
+ gpios = <&pio 121 GPIO_ACTIVE_HIGH>;
+ linux,code = <1>; /* SW_TABLET_MODE */
+ linux,input-type = <5>; /* EV_SW */
+ gpio-key,wakeup;
+ };
+
+ volume_down {
+ label = "Volume_down";
+ gpios = <&pio 123 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEDOWN>;
+ };
+
+ volume_up {
+ label = "Volume_up";
+ gpios = <&pio 124 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEUP>;
+ };
+ };
+
+ panel: panel {
+ compatible = "lg,lp120up1";
+ power-supply = <&panel_fixed_3v3>;
+ ddc-i2c-bus = <&i2c0>;
+ backlight = <&backlight_lcd>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&ps8640_out>;
+ };
+ };
+ };
+
+ panel_fixed_3v3: regulator@1 {
+ compatible = "regulator-fixed";
+ regulator-name = "PANEL_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ gpio = <&pio 41 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&panel_fixed_pins>;
+ };
+
+ ps8640_fixed_1v2: regulator@2 {
+ compatible = "regulator-fixed";
+ regulator-name = "PS8640_1V2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-enable-ramp-delay = <2000>;
+ enable-active-high;
+ regulator-boot-on;
+ gpio = <&pio 30 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ps8640_fixed_pins>;
+ };
+
+ sdio_fixed_3v3: fixedregulator@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&pio 85 GPIO_ACTIVE_HIGH>;
+ };
+
+ sound: sound {
+ compatible = "mediatek,mt8173-rt5650";
+ mediatek,audio-codec = <&rt5650 &hdmi0>;
+ mediatek,platform = <&afe>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&aud_i2s2>;
+
+ mediatek,mclk = <1>;
+ codec-capture {
+ sound-dai = <&rt5650 1>;
+ };
+ };
+
+ hdmicon: connector {
+ compatible = "hdmi-connector";
+ label = "hdmi";
+ type = "a";
+ ddc-i2c-bus = <&hdmiddc0>;
+
+ port {
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&hdmi0_out>;
+ };
+ };
+ };
+};
+
+&cec {
+ status = "okay";
+};
+
+&cpu0 {
+ proc-supply = <&mt6397_vpca15_reg>;
+};
+
+&cpu1 {
+ proc-supply = <&mt6397_vpca15_reg>;
+};
+
+&cpu2 {
+ proc-supply = <&da9211_vcpu_reg>;
+ sram-supply = <&mt6397_vsramca7_reg>;
+};
+
+&cpu3 {
+ proc-supply = <&da9211_vcpu_reg>;
+ sram-supply = <&mt6397_vsramca7_reg>;
+};
+
+&cpu_thermal {
+ sustainable-power = <4500>; /* milliwatts */
+ trips {
+ threshold: trip-point@0 {
+ temperature = <60000>;
+ };
+
+ target: trip-point@1 {
+ temperature = <65000>;
+ };
+ };
+};
+
+&dsi0 {
+ status = "okay";
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@1 {
+ dsi0_out: endpoint {
+ remote-endpoint = <&ps8640_in>;
+ };
+ };
+ };
+};
+
+&dpi0 {
+ status = "okay";
+};
+
+&hdmi0 {
+ status = "okay";
+ ports {
+ port@1 {
+ reg = <1>;
+
+ hdmi0_out: endpoint {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+ };
+ };
+};
+
+&hdmi_phy {
+ status = "okay";
+ mediatek,ibias = <0xc>;
+};
+
+&i2c0 {
+ status = "okay";
+
+ rt5650: audio-codec@1a {
+ compatible = "realtek,rt5650";
+ reg = <0x1a>;
+ avdd-supply = <&mt6397_vgp1_reg>;
+ cpvdd-supply = <&mt6397_vcama_reg>;
+ interrupt-parent = <&pio>;
+ interrupts = <3 IRQ_TYPE_EDGE_BOTH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&rt5650_irq>;
+ #sound-dai-cells = <1>;
+ realtek,dmic1-data-pin = <2>;
+ realtek,jd-mode = <2>;
+ };
+
+ ps8640: edp-bridge@8 {
+ compatible = "parade,ps8640";
+ reg = <0x8>;
+ powerdown-gpios = <&pio 127 GPIO_ACTIVE_LOW>;
+ reset-gpios = <&pio 115 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ps8640_pins>;
+ vdd12-supply = <&ps8640_fixed_1v2>;
+ vdd33-supply = <&mt6397_vgp2_reg>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ ps8640_in: endpoint {
+ remote-endpoint = <&dsi0_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ ps8640_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+ };
+};
+
+&i2c1 {
+ clock-frequency = <1500000>;
+ status = "okay";
+
+ da9211: da9211@68 {
+ compatible = "dlg,da9211";
+ reg = <0x68>;
+
+ regulators {
+ da9211_vcpu_reg: BUCKA {
+ regulator-name = "VBUCKA";
+ regulator-min-microvolt = < 700000>;
+ regulator-max-microvolt = <1310000>;
+ regulator-min-microamp = <2000000>;
+ regulator-max-microamp = <4400000>;
+ regulator-ramp-delay = <10000>;
+ regulator-always-on;
+ regulator-allowed-modes = <0 1>;
+ };
+
+ da9211_vgpu_reg: BUCKB {
+ regulator-name = "VBUCKB";
+ regulator-min-microvolt = < 700000>;
+ regulator-max-microvolt = <1310000>;
+ regulator-min-microamp = <2000000>;
+ regulator-max-microamp = <3000000>;
+ regulator-ramp-delay = <10000>;
+ };
+ };
+ };
+};
+
+&i2c2 {
+ status = "okay";
+
+ tpm: tpm@20 {
+ compatible = "infineon,slb9645tt";
+ reg = <0x20>;
+ powered-while-suspended;
+ };
+};
+
+&i2c3 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ touchscreen: touchscreen@10 {
+ compatible = "elan,ekth3500";
+ reg = <0x10>;
+ interrupt-parent = <&pio>;
+ interrupts = <88 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&i2c4 {
+ clock-frequency = <400000>;
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&trackpad_irq>;
+
+ trackpad: trackpad@15 {
+ compatible = "elan,ekth3000";
+ interrupt-parent = <&pio>;
+ interrupts = <117 IRQ_TYPE_LEVEL_LOW>;
+ reg = <0x15>;
+ vcc-supply = <&mt6397_vgp6_reg>;
+ wakeup-source;
+ };
+};
+
+&mipi_tx0 {
+ status = "okay";
+};
+
+&mmc0 {
+ status = "okay";
+ pinctrl-names = "default", "state_uhs";
+ pinctrl-0 = <&mmc0_pins_default>;
+ pinctrl-1 = <&mmc0_pins_uhs>;
+ bus-width = <8>;
+ max-frequency = <200000000>;
+ cap-mmc-highspeed;
+ mmc-hs200-1_8v;
+ mmc-hs400-1_8v;
+ cap-mmc-hw-reset;
+ hs400-ds-delay = <0x14015>;
+ mediatek,hs200-cmd-int-delay=<30>;
+ mediatek,hs400-cmd-int-delay=<14>;
+ mediatek,hs400-cmd-resp-sel-rising;
+ vmmc-supply = <&mt6397_vemc_3v3_reg>;
+ vqmmc-supply = <&mt6397_vio18_reg>;
+ assigned-clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL_D2>;
+ non-removable;
+};
+
+&mmc1 {
+ status = "okay";
+ pinctrl-names = "default", "state_uhs";
+ pinctrl-0 = <&mmc1_pins_default>;
+ pinctrl-1 = <&mmc1_pins_uhs>;
+ bus-width = <4>;
+ max-frequency = <200000000>;
+ cap-sd-highspeed;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+ cd-gpios = <&pio 1 GPIO_ACTIVE_HIGH>;
+ vmmc-supply = <&mt6397_vmch_reg>;
+ vqmmc-supply = <&mt6397_vmc_reg>;
+};
+
+&mmc3 {
+ status = "okay";
+ pinctrl-names = "default", "state_uhs";
+ pinctrl-0 = <&mmc3_pins_default>;
+ pinctrl-1 = <&mmc3_pins_uhs>;
+ bus-width = <4>;
+ max-frequency = <200000000>;
+ cap-sd-highspeed;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+ sdr104-clk-delay = <5>;
+ keep-power-in-suspend;
+ enable-sdio-wakeup;
+ cap-sdio-irq;
+ vmmc-supply = <&sdio_fixed_3v3>;
+ vqmmc-supply = <&mt6397_vgp3_reg>;
+ non-removable;
+ cap-power-off-card;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ btmrvl: btmrvl@2 {
+ compatible = "marvell,sd8897-bt";
+ reg = <2>;
+ interrupt-parent = <&pio>;
+ interrupts = <119 IRQ_TYPE_LEVEL_LOW>;
+ marvell,wakeup-pin = /bits/ 16 <0x0d>;
+ marvell,wakeup-gap-ms = /bits/ 16 <0x64>;
+ };
+
+ mwifiex: mwifiex@1 {
+ compatible = "marvell,sd8897";
+ reg = <1>;
+ interrupt-parent = <&pio>;
+ interrupts = <38 IRQ_TYPE_LEVEL_LOW>;
+ marvell,wakeup-pin = <3>;
+ marvell,caldata_ed_mac = /bits/ 8 <
+0x01 0x00 0x07 0x00 0x14 0x00 0x01 0x00 0x00 0x00 0x12 0x00 0x02 0x00 0x01 0x00
+0x01 0x00 0x00 0x00 0x12 0x00 0x02 0x00 0x01 0x00
+ >;
+ };
+};
+
+&nor_flash {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&nor_gpio1_pins>;
+ bus-width = <8>;
+ max-frequency = <50000000>;
+ non-removable;
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ };
+};
+
+&pio {
+ aud_i2s2: aud_i2s2 {
+ pins1 {
+ pinmux = <MT8173_PIN_128_I2S0_LRCK__FUNC_I2S1_WS>,
+ <MT8173_PIN_129_I2S0_BCK__FUNC_I2S1_BCK>,
+ <MT8173_PIN_130_I2S0_MCK__FUNC_I2S1_MCK>,
+ <MT8173_PIN_131_I2S0_DATA0__FUNC_I2S1_DO_1>,
+ <MT8173_PIN_12_EINT12__FUNC_I2S2_WS>,
+ <MT8173_PIN_13_EINT13__FUNC_I2S2_BCK>,
+ <MT8173_PIN_132_I2S0_DATA1__FUNC_I2S2_DI_2>;
+ bias-pull-down;
+ };
+ };
+
+ bl_fixed_pins: bl_fixed_pins {
+ pins1 {
+ pinmux = <MT8173_PIN_32_UTXD2__FUNC_GPIO32>;
+ output-low;
+ };
+ };
+
+ bt_wake_pins: bt_wake_pins {
+ pins1 {
+ pinmux = <MT8173_PIN_119_KPROW0__FUNC_GPIO119>;
+ bias-pull-up;
+ };
+ };
+
+ disp_pwm0_pins: disp_pwm0_pins {
+ pins1 {
+ pinmux = <MT8173_PIN_87_DISP_PWM0__FUNC_DISP_PWM0>;
+ output-low;
+ };
+ };
+
+ gpio_keys_pins: gpio_keys_pins {
+ volume_pins {
+ pinmux = <MT8173_PIN_123_KPCOL1__FUNC_GPIO123>,
+ <MT8173_PIN_124_KPCOL2__FUNC_GPIO124>;
+ bias-pull-up;
+ };
+
+ tablet_mode_pins {
+ pinmux = <MT8173_PIN_121_KPROW2__FUNC_GPIO121>;
+ bias-pull-up;
+ };
+ };
+
+ hdmi_mux_pins: hdmi_mux_pins {
+ pins1 {
+ pinmux = <MT8173_PIN_36_DAISYNC__FUNC_GPIO36>;
+ };
+ };
+
+ mmc0_pins_default: mmc0default {
+ pins_cmd_dat {
+ pinmux = <MT8173_PIN_57_MSDC0_DAT0__FUNC_MSDC0_DAT0>,
+ <MT8173_PIN_58_MSDC0_DAT1__FUNC_MSDC0_DAT1>,
+ <MT8173_PIN_59_MSDC0_DAT2__FUNC_MSDC0_DAT2>,
+ <MT8173_PIN_60_MSDC0_DAT3__FUNC_MSDC0_DAT3>,
+ <MT8173_PIN_61_MSDC0_DAT4__FUNC_MSDC0_DAT4>,
+ <MT8173_PIN_62_MSDC0_DAT5__FUNC_MSDC0_DAT5>,
+ <MT8173_PIN_63_MSDC0_DAT6__FUNC_MSDC0_DAT6>,
+ <MT8173_PIN_64_MSDC0_DAT7__FUNC_MSDC0_DAT7>,
+ <MT8173_PIN_66_MSDC0_CMD__FUNC_MSDC0_CMD>;
+ bias-pull-up;
+ };
+
+ pins_clk {
+ pinmux = <MT8173_PIN_65_MSDC0_CLK__FUNC_MSDC0_CLK>;
+ bias-pull-down;
+ };
+
+ pins_rst {
+ pinmux = <MT8173_PIN_68_MSDC0_RST___FUNC_MSDC0_RSTB>;
+ bias-pull-up;
+ };
+ };
+
+ mmc1_pins_default: mmc1default {
+ pins_cmd_dat {
+ pinmux = <MT8173_PIN_73_MSDC1_DAT0__FUNC_MSDC1_DAT0>,
+ <MT8173_PIN_74_MSDC1_DAT1__FUNC_MSDC1_DAT1>,
+ <MT8173_PIN_75_MSDC1_DAT2__FUNC_MSDC1_DAT2>,
+ <MT8173_PIN_76_MSDC1_DAT3__FUNC_MSDC1_DAT3>,
+ <MT8173_PIN_78_MSDC1_CMD__FUNC_MSDC1_CMD>;
+ input-enable;
+ drive-strength = <MTK_DRIVE_4mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
+ };
+
+ pins_clk {
+ pinmux = <MT8173_PIN_77_MSDC1_CLK__FUNC_MSDC1_CLK>;
+ bias-pull-down;
+ drive-strength = <MTK_DRIVE_4mA>;
+ };
+
+ pins_insert {
+ pinmux = <MT8173_PIN_1_EINT1__FUNC_GPIO1>;
+ bias-pull-up;
+ };
+ };
+
+ mmc3_pins_default: mmc3default {
+ pins_dat {
+ pinmux = <MT8173_PIN_22_MSDC3_DAT0__FUNC_MSDC3_DAT0>,
+ <MT8173_PIN_23_MSDC3_DAT1__FUNC_MSDC3_DAT1>,
+ <MT8173_PIN_24_MSDC3_DAT2__FUNC_MSDC3_DAT2>,
+ <MT8173_PIN_25_MSDC3_DAT3__FUNC_MSDC3_DAT3>;
+ input-enable;
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
+ };
+
+ pins_cmd {
+ pinmux = <MT8173_PIN_27_MSDC3_CMD__FUNC_MSDC3_CMD>;
+ input-enable;
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
+ };
+
+ pins_clk {
+ pinmux = <MT8173_PIN_26_MSDC3_CLK__FUNC_MSDC3_CLK>;
+ bias-pull-down;
+ drive-strength = <MTK_DRIVE_8mA>;
+ };
+
+ pins_pdn {
+ pinmux = <MT8173_PIN_85_AUD_DAT_MOSI__FUNC_GPIO85>;
+ output-low;
+ };
+ };
+
+ mmc0_pins_uhs: mmc0 {
+ pins_cmd_dat {
+ pinmux = <MT8173_PIN_57_MSDC0_DAT0__FUNC_MSDC0_DAT0>,
+ <MT8173_PIN_58_MSDC0_DAT1__FUNC_MSDC0_DAT1>,
+ <MT8173_PIN_59_MSDC0_DAT2__FUNC_MSDC0_DAT2>,
+ <MT8173_PIN_60_MSDC0_DAT3__FUNC_MSDC0_DAT3>,
+ <MT8173_PIN_61_MSDC0_DAT4__FUNC_MSDC0_DAT4>,
+ <MT8173_PIN_62_MSDC0_DAT5__FUNC_MSDC0_DAT5>,
+ <MT8173_PIN_63_MSDC0_DAT6__FUNC_MSDC0_DAT6>,
+ <MT8173_PIN_64_MSDC0_DAT7__FUNC_MSDC0_DAT7>,
+ <MT8173_PIN_66_MSDC0_CMD__FUNC_MSDC0_CMD>;
+ input-enable;
+ drive-strength = <MTK_DRIVE_6mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+
+ pins_clk {
+ pinmux = <MT8173_PIN_65_MSDC0_CLK__FUNC_MSDC0_CLK>;
+ drive-strength = <MTK_DRIVE_6mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_01>;
+ };
+
+ pins_ds {
+ pinmux = <MT8173_PIN_67_MSDC0_DSL__FUNC_MSDC0_DSL>;
+ drive-strength = <MTK_DRIVE_10mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_01>;
+ };
+
+ pins_rst {
+ pinmux = <MT8173_PIN_68_MSDC0_RST___FUNC_MSDC0_RSTB>;
+ bias-pull-up;
+ };
+ };
+
+ mmc1_pins_uhs: mmc1 {
+ pins_cmd_dat {
+ pinmux = <MT8173_PIN_73_MSDC1_DAT0__FUNC_MSDC1_DAT0>,
+ <MT8173_PIN_74_MSDC1_DAT1__FUNC_MSDC1_DAT1>,
+ <MT8173_PIN_75_MSDC1_DAT2__FUNC_MSDC1_DAT2>,
+ <MT8173_PIN_76_MSDC1_DAT3__FUNC_MSDC1_DAT3>,
+ <MT8173_PIN_78_MSDC1_CMD__FUNC_MSDC1_CMD>;
+ input-enable;
+ drive-strength = <MTK_DRIVE_6mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
+ };
+
+ pins_clk {
+ pinmux = <MT8173_PIN_77_MSDC1_CLK__FUNC_MSDC1_CLK>;
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+ };
+ };
+
+ mmc3_pins_uhs: mmc3 {
+ pins_dat {
+ pinmux = <MT8173_PIN_22_MSDC3_DAT0__FUNC_MSDC3_DAT0>,
+ <MT8173_PIN_23_MSDC3_DAT1__FUNC_MSDC3_DAT1>,
+ <MT8173_PIN_24_MSDC3_DAT2__FUNC_MSDC3_DAT2>,
+ <MT8173_PIN_25_MSDC3_DAT3__FUNC_MSDC3_DAT3>;
+ input-enable;
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
+ };
+
+ pins_cmd {
+ pinmux = <MT8173_PIN_27_MSDC3_CMD__FUNC_MSDC3_CMD>;
+ input-enable;
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
+ };
+
+ pins_clk {
+ pinmux = <MT8173_PIN_26_MSDC3_CLK__FUNC_MSDC3_CLK>;
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+ };
+ };
+
+ nor_gpio1_pins: nor {
+ pins1 {
+ pinmux = <MT8173_PIN_6_EINT6__FUNC_SFCS0>,
+ <MT8173_PIN_7_EINT7__FUNC_SFHOLD>,
+ <MT8173_PIN_8_EINT8__FUNC_SFIN>;
+ input-enable;
+ drive-strength = <MTK_DRIVE_4mA>;
+ bias-pull-up;
+ };
+
+ pins2 {
+ pinmux = <MT8173_PIN_5_EINT5__FUNC_SFOUT>;
+ drive-strength = <MTK_DRIVE_4mA>;
+ bias-pull-up;
+ };
+
+ pins_clk {
+ pinmux = <MT8173_PIN_9_EINT9__FUNC_SFCK>;
+ input-enable;
+ drive-strength = <MTK_DRIVE_4mA>;
+ bias-pull-up;
+ };
+ };
+
+ panel_fixed_pins: panel_fixed_pins {
+ pins1 {
+ pinmux = <MT8173_PIN_41_CMMCLK__FUNC_GPIO41>;
+ };
+ };
+
+ ps8640_pins: ps8640_pins {
+ pins1 {
+ pinmux = <MT8173_PIN_92_PCM_CLK__FUNC_GPIO92>,
+ <MT8173_PIN_115_URTS0__FUNC_GPIO115>,
+ <MT8173_PIN_127_LCM_RST__FUNC_GPIO127>;
+ };
+ };
+
+ ps8640_fixed_pins: ps8640_fixed_pins {
+ pins1 {
+ pinmux = <MT8173_PIN_30_URTS2__FUNC_GPIO30>;
+ };
+ };
+
+ rt5650_irq: rt5650_irq {
+ pins1 {
+ pinmux = <MT8173_PIN_3_EINT3__FUNC_GPIO3>;
+ bias-pull-down;
+ };
+ };
+
+ spi_pins_a: spi1 {
+ pins1 {
+ pinmux = <MT8173_PIN_0_EINT0__FUNC_GPIO0>;
+ bias-pull-up;
+ };
+
+ pins_spi {
+ pinmux = <MT8173_PIN_102_MSDC2_DAT2__FUNC_SPI_CK_1_>,
+ <MT8173_PIN_103_MSDC2_DAT3__FUNC_SPI_MI_1_>,
+ <MT8173_PIN_104_MSDC2_CLK__FUNC_SPI_MO_1_>,
+ <MT8173_PIN_105_MSDC2_CMD__FUNC_SPI_CS_1_>;
+ bias-disable;
+ };
+ };
+
+ trackpad_irq: trackpad_irq {
+ pins1 {
+ pinmux = <MT8173_PIN_117_URXD3__FUNC_GPIO117>;
+ input-enable;
+ bias-pull-up;
+ };
+ };
+
+ usb_pins: usb@0 {
+ pins1 {
+ pinmux = <MT8173_PIN_101_MSDC2_DAT1__FUNC_GPIO101>;
+ output-high;
+ bias-disable;
+ };
+ };
+
+ wifi_wake_pins: wifi_wake_pins {
+ pins1 {
+ pinmux = <MT8173_PIN_38_CONN_RST__FUNC_GPIO38>;
+ bias-pull-up;
+ };
+ };
+};
+
+&pwm0 {
+ status = "okay";
+};
+
+&pwrap {
+ pmic: mt6397 {
+ compatible = "mediatek,mt6397";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ interrupt-parent = <&pio>;
+ interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ mt6397rtc: mt6397rtc {
+ compatible = "mediatek,mt6397-rtc";
+ };
+
+ syscfg_pctl_pmic: syscfg_pctl_pmic@c000 {
+ compatible = "mediatek,mt6397-pctl-pmic-syscfg",
+ "syscon";
+ reg = <0 0x0000c000 0 0x0108>;
+ };
+
+ pio6397: pinctrl@c000 {
+ compatible = "mediatek,mt6397-pinctrl";
+ pins-are-numbered;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ mt6397clock: mt6397clock {
+ compatible = "mediatek,mt6397-clk";
+ #clock-cells = <1>;
+ };
+
+ mt6397regulator: mt6397regulator {
+ compatible = "mediatek,mt6397-regulator";
+
+ mt6397_vpca15_reg: buck_vpca15 {
+ regulator-compatible = "buck_vpca15";
+ regulator-name = "vpca15";
+ regulator-min-microvolt = < 700000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <12500>;
+ regulator-always-on;
+ regulator-allowed-modes = <0 1>;
+ };
+
+ mt6397_vpca7_reg: buck_vpca7 {
+ regulator-compatible = "buck_vpca7";
+ regulator-name = "vpca7";
+ regulator-min-microvolt = < 700000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <12500>;
+ regulator-enable-ramp-delay = <115>;
+ regulator-always-on;
+ };
+
+ mt6397_vsramca15_reg: buck_vsramca15 {
+ regulator-compatible = "buck_vsramca15";
+ regulator-name = "vsramca15";
+ regulator-min-microvolt = < 700000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <12500>;
+ regulator-always-on;
+ };
+
+ mt6397_vsramca7_reg: buck_vsramca7 {
+ regulator-compatible = "buck_vsramca7";
+ regulator-name = "vsramca7";
+ regulator-min-microvolt = < 700000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <12500>;
+ regulator-always-on;
+ };
+
+ mt6397_vcore_reg: buck_vcore {
+ regulator-compatible = "buck_vcore";
+ regulator-name = "vcore";
+ regulator-min-microvolt = < 700000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <12500>;
+ regulator-always-on;
+ };
+
+ mt6397_vgpu_reg: buck_vgpu {
+ regulator-compatible = "buck_vgpu";
+ regulator-name = "vgpu";
+ regulator-min-microvolt = < 700000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <12500>;
+ regulator-enable-ramp-delay = <115>;
+ };
+
+ mt6397_vdrm_reg: buck_vdrm {
+ regulator-compatible = "buck_vdrm";
+ regulator-name = "vdrm";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-ramp-delay = <12500>;
+ regulator-always-on;
+ };
+
+ mt6397_vio18_reg: buck_vio18 {
+ regulator-compatible = "buck_vio18";
+ regulator-name = "vio18";
+ regulator-min-microvolt = <1620000>;
+ regulator-max-microvolt = <1980000>;
+ regulator-ramp-delay = <12500>;
+ regulator-always-on;
+ };
+
+ mt6397_vtcxo_reg: ldo_vtcxo {
+ regulator-compatible = "ldo_vtcxo";
+ regulator-name = "vtcxo";
+ regulator-always-on;
+ };
+
+ mt6397_va28_reg: ldo_va28 {
+ regulator-compatible = "ldo_va28";
+ regulator-name = "va28";
+ };
+
+ mt6397_vcama_reg: ldo_vcama {
+ regulator-compatible = "ldo_vcama";
+ regulator-name = "vcama";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-enable-ramp-delay = <218>;
+ };
+
+ mt6397_vio28_reg: ldo_vio28 {
+ regulator-compatible = "ldo_vio28";
+ regulator-name = "vio28";
+ regulator-always-on;
+ };
+
+ mt6397_vusb_reg: ldo_vusb {
+ regulator-compatible = "ldo_vusb";
+ regulator-name = "vusb";
+ };
+
+ mt6397_vmc_reg: ldo_vmc {
+ regulator-compatible = "ldo_vmc";
+ regulator-name = "vmc";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-enable-ramp-delay = <218>;
+ };
+
+ mt6397_vmch_reg: ldo_vmch {
+ regulator-compatible = "ldo_vmch";
+ regulator-name = "vmch";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-enable-ramp-delay = <218>;
+ };
+
+ mt6397_vemc_3v3_reg: ldo_vemc3v3 {
+ regulator-compatible = "ldo_vemc3v3";
+ regulator-name = "vemc_3v3";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-enable-ramp-delay = <218>;
+ };
+
+ mt6397_vgp1_reg: ldo_vgp1 {
+ regulator-compatible = "ldo_vgp1";
+ regulator-name = "vcamd";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-enable-ramp-delay = <240>;
+ };
+
+ mt6397_vgp2_reg: ldo_vgp2 {
+ regulator-compatible = "ldo_vgp2";
+ regulator-name = "vcamio";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-enable-ramp-delay = <218>;
+ };
+
+ mt6397_vgp3_reg: ldo_vgp3 {
+ regulator-compatible = "ldo_vgp3";
+ regulator-name = "vcamaf";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-enable-ramp-delay = <218>;
+ };
+
+ mt6397_vgp4_reg: ldo_vgp4 {
+ regulator-compatible = "ldo_vgp4";
+ regulator-name = "vgp4";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-enable-ramp-delay = <218>;
+ };
+
+ mt6397_vgp5_reg: ldo_vgp5 {
+ regulator-compatible = "ldo_vgp5";
+ regulator-name = "vgp5";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-enable-ramp-delay = <218>;
+ };
+
+ mt6397_vgp6_reg: ldo_vgp6 {
+ regulator-compatible = "ldo_vgp6";
+ regulator-name = "vgp6";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-enable-ramp-delay = <218>;
+ regulator-always-on;
+ };
+
+ mt6397_vibr_reg: ldo_vibr {
+ regulator-compatible = "ldo_vibr";
+ regulator-name = "vibr";
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-enable-ramp-delay = <218>;
+ };
+ };
+ };
+};
+
+&spi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi_pins_a>;
+ mediatek,pad-select = <1>;
+ status = "okay";
+ /* clients */
+ cros_ec: ec@0 {
+ compatible = "google,cros-ec-spi";
+ reg = <0x0>;
+ spi-max-frequency = <12000000>;
+ interrupt-parent = <&pio>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ google,cros-ec-spi-msg-delay = <500>;
+
+ i2c_tunnel: i2c-tunnel@0 {
+ compatible = "google,cros-ec-i2c-tunnel";
+ google,remote-bus = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ battery: sbs-battery@b {
+ compatible = "sbs,sbs-battery";
+ reg = <0xb>;
+ sbs,i2c-retry-count = <2>;
+ sbs,poll-retry-count = <1>;
+ };
+ };
+ };
+};
+
+&thermal {
+ bank0-supply = <&mt6397_vpca15_reg>;
+ bank1-supply = <&da9211_vcpu_reg>;
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&ssusb {
+ dr_mode = "host";
+ wakeup-source;
+ vusb33-supply = <&mt6397_vusb_reg>;
+ status = "okay";
+};
+
+&usb_host {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb_pins>;
+ vusb33-supply = <&mt6397_vusb_reg>;
+ status = "okay";
+};
+
+#include "../../../../arm/boot/dts/cros-ec-keyboard.dtsi"
\ No newline at end of file
--
2.25.0.rc1.283.g88dfdc4193-goog
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 14+ messages in thread
* Re: [PATCH v2 2/2] arm64: dts: mediatek: add mt8173 elm and hana board
2020-01-10 7:37 ` [PATCH v2 2/2] arm64: dts: mediatek: add mt8173 elm and hana board Hsin-Yi Wang
@ 2020-01-10 8:52 ` Yingjoe Chen
2020-01-10 13:42 ` Matthias Brugger
2020-01-13 9:29 ` Enric Balletbo i Serra
2 siblings, 0 replies; 14+ messages in thread
From: Yingjoe Chen @ 2020-01-10 8:52 UTC (permalink / raw)
To: Hsin-Yi Wang
Cc: Mark Rutland, devicetree, Nicolas Boichat, linux-kernel,
Matthias Brugger, Rob Herring, linux-mediatek,
Enric Balletbo i Serra, linux-arm-kernel
On Fri, 2020-01-10 at 15:37 +0800, Hsin-Yi Wang wrote:
> Elm is Acer Chromebook R13. Hana is Lenovo Chromebook. Both uses mt8173
> SoC.
>
> Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
> ---
> Changes in v2:
> - remove downstream nodes and unused nodes
> - use GPIO_ACTIVE_LOW for ps8640 gpios
> - move trackpad to hana
> ---
> arch/arm64/boot/dts/mediatek/Makefile | 3 +
> .../dts/mediatek/mt8173-elm-hana-rev7.dts | 27 +
> .../boot/dts/mediatek/mt8173-elm-hana.dts | 16 +
> .../boot/dts/mediatek/mt8173-elm-hana.dtsi | 60 +
> arch/arm64/boot/dts/mediatek/mt8173-elm.dts | 15 +
> arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi | 1040 +++++++++++++++++
> 6 files changed, 1161 insertions(+)
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dtsi
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm.dts
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi
>
> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> index 458bbc422a94..b45a45a565a1 100644
> --- a/arch/arm64/boot/dts/mediatek/Makefile
> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> @@ -6,5 +6,8 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana-rev7.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-evb.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-evb.dtb
> diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts
> new file mode 100644
> index 000000000000..a3616bc3d859
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts
> @@ -0,0 +1,27 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright 2019 MediaTek Inc.
> + */
> +
> +/dts-v1/;
> +#include "mt8173-elm-hana.dtsi"
> +
> +/ {
> + model = "Mediatek Hana rev7 board";
> + compatible = "google,hana-rev7", "mediatek,mt8173";
> +};
> +
> +&cpu_thermal {
> + trips {
> + cpu_crit: cpu_crit@0 {
> + temperature = <100000>;
> + type = "critical";
> + };
> + };
> +};
> +
> +&gpio_keys {
> + /delete-node/tablet_mode;
> + /delete-node/volume_down;
> + /delete-node/volume_up;
> +};
> \ No newline at end of file
nit: Please add a newline at end of file for all files in this patch.
> diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts
> new file mode 100644
> index 000000000000..8cbcc75192e3
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts
> @@ -0,0 +1,16 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright 2016 MediaTek Inc.
> + */
> +
> +/dts-v1/;
> +#include "mt8173-elm-hana.dtsi"
> +
> +/ {
> + model = "Mediatek Hana rev0 board";
> + compatible = "google,hana-rev6",
> + "google,hana-rev5", "google,hana-rev4",
> + "google,hana-rev3", "google,hana-rev2",
> + "google,hana-rev1", "google,hana-rev0",
> + "google,hana", "mediatek,mt8173";
> +};
> \ No newline at end of file
<...>
> +
> +&pwrap {
> + pmic: mt6397 {
> + compatible = "mediatek,mt6397";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + interrupt-parent = <&pio>;
> + interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> +
> + mt6397rtc: mt6397rtc {
> + compatible = "mediatek,mt6397-rtc";
> + };
> +
> + syscfg_pctl_pmic: syscfg_pctl_pmic@c000 {
> + compatible = "mediatek,mt6397-pctl-pmic-syscfg",
> + "syscon";
> + reg = <0 0x0000c000 0 0x0108>;
> + };
> +
> + pio6397: pinctrl@c000 {
> + compatible = "mediatek,mt6397-pinctrl";
> + pins-are-numbered;
> + gpio-controller;
> + #gpio-cells = <2>;
> + };
> +
> + mt6397clock: mt6397clock {
> + compatible = "mediatek,mt6397-clk";
> + #clock-cells = <1>;
> + };
> +
> + mt6397regulator: mt6397regulator {
> + compatible = "mediatek,mt6397-regulator";
> +
> + mt6397_vpca15_reg: buck_vpca15 {
> + regulator-compatible = "buck_vpca15";
> + regulator-name = "vpca15";
> + regulator-min-microvolt = < 700000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <12500>;
> + regulator-always-on;
> + regulator-allowed-modes = <0 1>;
> + };
> +
> + mt6397_vpca7_reg: buck_vpca7 {
> + regulator-compatible = "buck_vpca7";
> + regulator-name = "vpca7";
> + regulator-min-microvolt = < 700000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <12500>;
> + regulator-enable-ramp-delay = <115>;
> + regulator-always-on;
> + };
> +
> + mt6397_vsramca15_reg: buck_vsramca15 {
> + regulator-compatible = "buck_vsramca15";
> + regulator-name = "vsramca15";
> + regulator-min-microvolt = < 700000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <12500>;
> + regulator-always-on;
> + };
> +
> + mt6397_vsramca7_reg: buck_vsramca7 {
> + regulator-compatible = "buck_vsramca7";
> + regulator-name = "vsramca7";
> + regulator-min-microvolt = < 700000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <12500>;
> + regulator-always-on;
> + };
> +
> + mt6397_vcore_reg: buck_vcore {
> + regulator-compatible = "buck_vcore";
> + regulator-name = "vcore";
> + regulator-min-microvolt = < 700000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <12500>;
> + regulator-always-on;
> + };
> +
> + mt6397_vgpu_reg: buck_vgpu {
> + regulator-compatible = "buck_vgpu";
> + regulator-name = "vgpu";
> + regulator-min-microvolt = < 700000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <12500>;
> + regulator-enable-ramp-delay = <115>;
> + };
> +
> + mt6397_vdrm_reg: buck_vdrm {
> + regulator-compatible = "buck_vdrm";
> + regulator-name = "vdrm";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1400000>;
> + regulator-ramp-delay = <12500>;
> + regulator-always-on;
> + };
> +
> + mt6397_vio18_reg: buck_vio18 {
> + regulator-compatible = "buck_vio18";
> + regulator-name = "vio18";
> + regulator-min-microvolt = <1620000>;
> + regulator-max-microvolt = <1980000>;
> + regulator-ramp-delay = <12500>;
> + regulator-always-on;
> + };
> +
> + mt6397_vtcxo_reg: ldo_vtcxo {
> + regulator-compatible = "ldo_vtcxo";
> + regulator-name = "vtcxo";
> + regulator-always-on;
> + };
> +
> + mt6397_va28_reg: ldo_va28 {
> + regulator-compatible = "ldo_va28";
> + regulator-name = "va28";
> + };
> +
> + mt6397_vcama_reg: ldo_vcama {
> + regulator-compatible = "ldo_vcama";
> + regulator-name = "vcama";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-enable-ramp-delay = <218>;
> + };
> +
> + mt6397_vio28_reg: ldo_vio28 {
> + regulator-compatible = "ldo_vio28";
> + regulator-name = "vio28";
> + regulator-always-on;
> + };
> +
> + mt6397_vusb_reg: ldo_vusb {
> + regulator-compatible = "ldo_vusb";
> + regulator-name = "vusb";
> + };
> +
> + mt6397_vmc_reg: ldo_vmc {
> + regulator-compatible = "ldo_vmc";
> + regulator-name = "vmc";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-enable-ramp-delay = <218>;
> + };
> +
> + mt6397_vmch_reg: ldo_vmch {
> + regulator-compatible = "ldo_vmch";
> + regulator-name = "vmch";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-enable-ramp-delay = <218>;
> + };
> +
> + mt6397_vemc_3v3_reg: ldo_vemc3v3 {
> + regulator-compatible = "ldo_vemc3v3";
> + regulator-name = "vemc_3v3";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-enable-ramp-delay = <218>;
> + };
> +
> + mt6397_vgp1_reg: ldo_vgp1 {
> + regulator-compatible = "ldo_vgp1";
> + regulator-name = "vcamd";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-enable-ramp-delay = <240>;
> + };
> +
> + mt6397_vgp2_reg: ldo_vgp2 {
> + regulator-compatible = "ldo_vgp2";
> + regulator-name = "vcamio";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-enable-ramp-delay = <218>;
> + };
> +
> + mt6397_vgp3_reg: ldo_vgp3 {
> + regulator-compatible = "ldo_vgp3";
> + regulator-name = "vcamaf";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-enable-ramp-delay = <218>;
> + };
> +
> + mt6397_vgp4_reg: ldo_vgp4 {
> + regulator-compatible = "ldo_vgp4";
> + regulator-name = "vgp4";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-enable-ramp-delay = <218>;
> + };
> +
> + mt6397_vgp5_reg: ldo_vgp5 {
> + regulator-compatible = "ldo_vgp5";
> + regulator-name = "vgp5";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-enable-ramp-delay = <218>;
> + };
> +
> + mt6397_vgp6_reg: ldo_vgp6 {
> + regulator-compatible = "ldo_vgp6";
> + regulator-name = "vgp6";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-enable-ramp-delay = <218>;
> + regulator-always-on;
> + };
> +
> + mt6397_vibr_reg: ldo_vibr {
> + regulator-compatible = "ldo_vibr";
> + regulator-name = "vibr";
> + regulator-min-microvolt = <1300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-enable-ramp-delay = <218>;
> + };
> + };
> + };
> +};
> +
> +&spi {
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi_pins_a>;
> + mediatek,pad-select = <1>;
> + status = "okay";
> + /* clients */
> + cros_ec: ec@0 {
> + compatible = "google,cros-ec-spi";
> + reg = <0x0>;
> + spi-max-frequency = <12000000>;
> + interrupt-parent = <&pio>;
> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> + google,cros-ec-spi-msg-delay = <500>;
> +
> + i2c_tunnel: i2c-tunnel@0 {
> + compatible = "google,cros-ec-i2c-tunnel";
> + google,remote-bus = <0>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + battery: sbs-battery@b {
> + compatible = "sbs,sbs-battery";
> + reg = <0xb>;
> + sbs,i2c-retry-count = <2>;
> + sbs,poll-retry-count = <1>;
> + };
> + };
> + };
> +};
> +
> +&thermal {
> + bank0-supply = <&mt6397_vpca15_reg>;
> + bank1-supply = <&da9211_vcpu_reg>;
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&ssusb {
sorting according to name, please put this before thermal.
Joe.C
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH v2 1/2] dt-bindings: arm64: dts: mediatek: Add mt8173 elm and hana
2020-01-10 7:37 ` [PATCH v2 1/2] dt-bindings: arm64: dts: mediatek: Add mt8173 elm and hana Hsin-Yi Wang
@ 2020-01-10 11:38 ` Enric Balletbo i Serra
2020-01-15 14:52 ` Rob Herring
1 sibling, 0 replies; 14+ messages in thread
From: Enric Balletbo i Serra @ 2020-01-10 11:38 UTC (permalink / raw)
To: Hsin-Yi Wang, linux-arm-kernel
Cc: Mark Rutland, devicetree, Nicolas Boichat, linux-kernel,
Daniel Kurtz, Rob Herring, linux-mediatek, Matthias Brugger
Hi Hsin-Yi,
Just a nit that is most a decision of the maintainer ...
On 10/1/20 8:37, Hsin-Yi Wang wrote:
> Elm is Acer Chromebook R13. Hana is Lenovo Chromebook. Both uses mt8173
> SoC.
>
> Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Tested with patch 2 applied and saw that there is no errors with dtbs_check.
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
> ---
> Changes in v2:
> - fix dtbs_check errors, use const instead of enum
> ---
> .../devicetree/bindings/arm/mediatek.yaml | 27 +++++++++++++++++++
> 1 file changed, 27 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/arm/mediatek.yaml b/Documentation/devicetree/bindings/arm/mediatek.yaml
> index 4043c5046441..5272899b08fa 100644
> --- a/Documentation/devicetree/bindings/arm/mediatek.yaml
> +++ b/Documentation/devicetree/bindings/arm/mediatek.yaml
> @@ -84,6 +84,33 @@ properties:
> - enum:
> - mediatek,mt8135-evbp1
> - const: mediatek,mt8135
> + - description: Google Elm (Acer Chromebook R13)
> + items:
> + - const: google,elm-rev8
> + - const: google,elm-rev7
> + - const: google,elm-rev6
> + - const: google,elm-rev5
> + - const: google,elm-rev4
> + - const: google,elm-rev3
> + - const: google,elm-rev2
> + - const: google,elm-rev1
> + - const: google,elm
> + - const: mediatek,mt8173
> + - description: Google Hana (Lenovo Chromebook and more)
nit: and more? How many? I'd expect the commercial model names here
Lenovo Chromebook C330?
Thanks,
Enric
> + items:
> + - const: google,hana-rev6
> + - const: google,hana-rev5
> + - const: google,hana-rev4
> + - const: google,hana-rev3
> + - const: google,hana-rev2
> + - const: google,hana-rev1
> + - const: google,hana-rev0
> + - const: google,hana
> + - const: mediatek,mt8173
> + - description: Google Hana rev7 (Poin2 Chromebook 11C)
> + items:
> + - const: google,hana-rev7
> + - const: mediatek,mt8173
> - items:
> - enum:
> - mediatek,mt8173-evb
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH v2 2/2] arm64: dts: mediatek: add mt8173 elm and hana board
2020-01-10 7:37 ` [PATCH v2 2/2] arm64: dts: mediatek: add mt8173 elm and hana board Hsin-Yi Wang
2020-01-10 8:52 ` Yingjoe Chen
@ 2020-01-10 13:42 ` Matthias Brugger
2020-01-13 18:01 ` Hsin-Yi Wang
2020-01-13 9:29 ` Enric Balletbo i Serra
2 siblings, 1 reply; 14+ messages in thread
From: Matthias Brugger @ 2020-01-10 13:42 UTC (permalink / raw)
To: Hsin-Yi Wang, linux-arm-kernel
Cc: Mark Rutland, devicetree, Nicolas Boichat, linux-kernel,
Daniel Kurtz, Rob Herring, linux-mediatek,
Enric Balletbo i Serra
On 10/01/2020 08:37, Hsin-Yi Wang wrote:
> Elm is Acer Chromebook R13. Hana is Lenovo Chromebook. Both uses mt8173
> SoC.
>
> Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
> ---
> Changes in v2:
> - remove downstream nodes and unused nodes
> - use GPIO_ACTIVE_LOW for ps8640 gpios
> - move trackpad to hana
> ---
> arch/arm64/boot/dts/mediatek/Makefile | 3 +
> .../dts/mediatek/mt8173-elm-hana-rev7.dts | 27 +
> .../boot/dts/mediatek/mt8173-elm-hana.dts | 16 +
> .../boot/dts/mediatek/mt8173-elm-hana.dtsi | 60 +
> arch/arm64/boot/dts/mediatek/mt8173-elm.dts | 15 +
> arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi | 1040 +++++++++++++++++
> 6 files changed, 1161 insertions(+)
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dtsi
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm.dts
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi
>
> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> index 458bbc422a94..b45a45a565a1 100644
> --- a/arch/arm64/boot/dts/mediatek/Makefile
> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> @@ -6,5 +6,8 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana-rev7.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-evb.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-evb.dtb
> diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts
> new file mode 100644
> index 000000000000..a3616bc3d859
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts
> @@ -0,0 +1,27 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright 2019 MediaTek Inc.
> + */
> +
> +/dts-v1/;
> +#include "mt8173-elm-hana.dtsi"
> +
> +/ {
> + model = "Mediatek Hana rev7 board";
> + compatible = "google,hana-rev7", "mediatek,mt8173";
> +};
> +
> +&cpu_thermal {
> + trips {
> + cpu_crit: cpu_crit@0 {
> + temperature = <100000>;
> + type = "critical";
> + };
> + };
> +};
> +
> +&gpio_keys {
> + /delete-node/tablet_mode;
> + /delete-node/volume_down;
> + /delete-node/volume_up;
> +};
> \ No newline at end of file
> diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts
> new file mode 100644
> index 000000000000..8cbcc75192e3
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts
> @@ -0,0 +1,16 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright 2016 MediaTek Inc.
> + */
> +
> +/dts-v1/;
> +#include "mt8173-elm-hana.dtsi"
> +
> +/ {
> + model = "Mediatek Hana rev0 board";
> + compatible = "google,hana-rev6",
> + "google,hana-rev5", "google,hana-rev4",
> + "google,hana-rev3", "google,hana-rev2",
> + "google,hana-rev1", "google,hana-rev0",
> + "google,hana", "mediatek,mt8173";
> +};
I'm a bit confused about all this versions. Do you want to keep them for
internal use, as I suppose only rev6 is available to the general public,
correct? I'm fine with keeping the old revisions if that's of use for you,
otherwise I'd prefer to delete them.
Model name could be more verbose.
> \ No newline at end of file
> diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dtsi b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dtsi
> new file mode 100644
> index 000000000000..35e12b290947
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dtsi
> @@ -0,0 +1,60 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright 2016 MediaTek Inc.
> + */
> +
> +#include "mt8173-elm.dtsi"
> +
> +&i2c0 {
> + clock-frequency = <200000>;
> +};
> +
> +&i2c3 {
> + touchscreen2: touchscreen@34 {
> + compatible = "melfas,mip4_ts";
> + reg = <0x34>;
> + interrupt-parent = <&pio>;
> + interrupts = <88 IRQ_TYPE_LEVEL_LOW>;
> + };
> +
> + touchscreen3: touchscreen@20 {
> + compatible = "hid-over-i2c";
> + reg = <0x20>;
> + hid-descr-addr = <0x0020>;
> + interrupt-parent = <&pio>;
> + interrupts = <88 IRQ_TYPE_LEVEL_LOW>;
> + };
In v1 you mentioned:
"Partners wants to increase touchpad and touchscreen source (they choose
synaptics) for hana 300e, and synaptics uses hid-over-i2c driver."
So the partner uses the same compatible (google,hana-rev6?) for both devices?
> +};
> +
> +&i2c4 {
> + trackpad2: trackpad@2c {
> + compatible = "hid-over-i2c";
> + interrupt-parent = <&pio>;
> + interrupts = <117 IRQ_TYPE_LEVEL_LOW>;
> + reg = <0x2c>;
> + hid-descr-addr = <0x0020>;
> + wakeup-source;
> + };
> +};
> +
> +&mmc1 {
> + wp-gpios = <&pio 42 GPIO_ACTIVE_HIGH>;
> +};
> +
> +&pio {
> + hdmi_mux_pins: hdmi_mux_pins {
> + pins2 {
> + pinmux = <MT8173_PIN_98_URTS1__FUNC_GPIO98>;
> + bias-pull-up;
> + output-high;
> + };
> + };
> +
> + mmc1_pins_default: mmc1default {
> + pins_wp {
> + pinmux = <MT8173_PIN_42_DSI_TE__FUNC_GPIO42>;
> + input-enable;
> + bias-pull-up;
> + };
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm.dts b/arch/arm64/boot/dts/mediatek/mt8173-elm.dts
> new file mode 100644
> index 000000000000..e5da2355760e
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8173-elm.dts
> @@ -0,0 +1,15 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright 2016 MediaTek Inc.
> + */
> +
> +/dts-v1/;
> +#include "mt8173-elm.dtsi"
> +
> +/ {
> + model = "Mediatek Elm board";
> + compatible = "google,elm-rev8", "google,elm-rev7", "google,elm-rev6",
> + "google,elm-rev5", "google,elm-rev4", "google,elm-rev3",
> + "google,elm-rev2", "google,elm-rev1",
> + "google,elm", "mediatek,mt8173";
> +};
> \ No newline at end of file
> diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi b/arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi
> new file mode 100644
> index 000000000000..2ac738bebe04
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi
> @@ -0,0 +1,1040 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright 2016 MediaTek Inc.
> + */
> +
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/gpio/gpio.h>
> +#include "mt8173.dtsi"
> +
> +/ {
> + aliases {
> + serial0 = &uart0;
> + serial1 = &uart1;
> + serial2 = &uart2;
> + serial3 = &uart3;
> + };
> +
> + memory@40000000 {
> + device_type = "memory";
> + reg = <0 0x40000000 0 0x80000000>;
> + };
> +
> + backlight_lcd: backlight_lcd {
> + compatible = "pwm-backlight";
> + pwms = <&pwm0 0 1000000>;
> + brightness-levels = <
> + 0 16 32 48 64 80 96 112
> + 128 144 160 176 192 208 224 240
> + 255
> + >;
> + default-brightness-level = <9>;
> + power-supply = <&bl_fixed_reg>;
> + enable-gpios = <&pio 95 GPIO_ACTIVE_HIGH>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&disp_pwm0_pins>;
> + status = "okay";
> + };
> +
> + bl_fixed_reg: fixedregulator@2 {
> + compatible = "regulator-fixed";
> + regulator-name = "bl_fixed";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + startup-delay-us = <1000>;
> + enable-active-high;
> + gpio = <&pio 32 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&bl_fixed_pins>;
> + };
> +
> + chosen {
> + stdout-path = &uart0;
> + };
> +
> + gpio_keys: gpio-keys {
> + compatible = "gpio-keys";
> + pinctrl-names = "default";
> + pinctrl-0 = <&gpio_keys_pins>;
> +
> + lid {
> + label = "Lid";
> + gpios = <&pio 69 GPIO_ACTIVE_LOW>;
> + linux,code = <0>; /* SW_LID */
> + linux,input-type = <5>; /* EV_SW */
> + gpio-key,wakeup;
> + };
> +
> + power {
> + label = "Power";
> + gpios = <&pio 14 GPIO_ACTIVE_HIGH>;
> + linux,code = <KEY_POWER>;
> + debounce-interval = <30>;
> + gpio-key,wakeup;
> + };
> +
> + tablet_mode {
> + label = "Tablet_mode";
> + gpios = <&pio 121 GPIO_ACTIVE_HIGH>;
> + linux,code = <1>; /* SW_TABLET_MODE */
can't we use SW_TABLET_MODE fomr linux-event-codes.h?
> + linux,input-type = <5>; /* EV_SW */
same here.
> + gpio-key,wakeup;
> + };
> +
> + volume_down {
> + label = "Volume_down";
> + gpios = <&pio 123 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_VOLUMEDOWN>;
> + };
> +
> + volume_up {
> + label = "Volume_up";
> + gpios = <&pio 124 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_VOLUMEUP>;
> + };
> + };
> +
> + panel: panel {
> + compatible = "lg,lp120up1";
> + power-supply = <&panel_fixed_3v3>;
> + ddc-i2c-bus = <&i2c0>;
> + backlight = <&backlight_lcd>;
> +
> + port {
> + panel_in: endpoint {
> + remote-endpoint = <&ps8640_out>;
> + };
> + };
> + };
> +
> + panel_fixed_3v3: regulator@1 {
> + compatible = "regulator-fixed";
> + regulator-name = "PANEL_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + enable-active-high;
> + gpio = <&pio 41 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&panel_fixed_pins>;
> + };
> +
> + ps8640_fixed_1v2: regulator@2 {
> + compatible = "regulator-fixed";
> + regulator-name = "PS8640_1V2";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-enable-ramp-delay = <2000>;
> + enable-active-high;
> + regulator-boot-on;
> + gpio = <&pio 30 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&ps8640_fixed_pins>;
> + };
> +
> + sdio_fixed_3v3: fixedregulator@0 {
> + compatible = "regulator-fixed";
> + regulator-name = "3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&pio 85 GPIO_ACTIVE_HIGH>;
we don't need to set the pincontroller mux here?
> + };
> +
> + sound: sound {
> + compatible = "mediatek,mt8173-rt5650";
> + mediatek,audio-codec = <&rt5650 &hdmi0>;
> + mediatek,platform = <&afe>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&aud_i2s2>;
> +
> + mediatek,mclk = <1>;
> + codec-capture {
> + sound-dai = <&rt5650 1>;
> + };
> + };
> +
> + hdmicon: connector {
> + compatible = "hdmi-connector";
> + label = "hdmi";
> + type = "a";
> + ddc-i2c-bus = <&hdmiddc0>;
> +
> + port {
> + hdmi_connector_in: endpoint {
> + remote-endpoint = <&hdmi0_out>;
> + };
> + };
> + };
> +};
> +
> +&cec {
> + status = "okay";
> +};
> +
> +&cpu0 {
> + proc-supply = <&mt6397_vpca15_reg>;
> +};
> +
> +&cpu1 {
> + proc-supply = <&mt6397_vpca15_reg>;
> +};
> +
> +&cpu2 {
> + proc-supply = <&da9211_vcpu_reg>;
> + sram-supply = <&mt6397_vsramca7_reg>;
> +};
> +
> +&cpu3 {
> + proc-supply = <&da9211_vcpu_reg>;
> + sram-supply = <&mt6397_vsramca7_reg>;
> +};
> +
> +&cpu_thermal {
> + sustainable-power = <4500>; /* milliwatts */
> + trips {
> + threshold: trip-point@0 {
> + temperature = <60000>;
> + };
> +
> + target: trip-point@1 {
> + temperature = <65000>;
> + };
> + };
> +};
> +
> +&dsi0 {
> + status = "okay";
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@1 {
> + dsi0_out: endpoint {
> + remote-endpoint = <&ps8640_in>;
> + };
> + };
> + };
> +};
> +
> +&dpi0 {
> + status = "okay";
> +};
> +
> +&hdmi0 {
> + status = "okay";
> + ports {
> + port@1 {
> + reg = <1>;
> +
> + hdmi0_out: endpoint {
> + remote-endpoint = <&hdmi_connector_in>;
> + };
> + };
> + };
> +};
> +
> +&hdmi_phy {
> + status = "okay";
> + mediatek,ibias = <0xc>;
> +};
> +
> +&i2c0 {
> + status = "okay";
> +
> + rt5650: audio-codec@1a {
> + compatible = "realtek,rt5650";
> + reg = <0x1a>;
> + avdd-supply = <&mt6397_vgp1_reg>;
> + cpvdd-supply = <&mt6397_vcama_reg>;
Hm, only defined for "realtek,rt5663", I suppose that's an inconsistency in the
binding documentation. Can you please double check?
> + interrupt-parent = <&pio>;
> + interrupts = <3 IRQ_TYPE_EDGE_BOTH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&rt5650_irq>;
> + #sound-dai-cells = <1>;
> + realtek,dmic1-data-pin = <2>;
> + realtek,jd-mode = <2>;
> + };
> +
> + ps8640: edp-bridge@8 {
> + compatible = "parade,ps8640";
> + reg = <0x8>;
> + powerdown-gpios = <&pio 127 GPIO_ACTIVE_LOW>;
> + reset-gpios = <&pio 115 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&ps8640_pins>;
> + vdd12-supply = <&ps8640_fixed_1v2>;
> + vdd33-supply = <&mt6397_vgp2_reg>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + ps8640_in: endpoint {
> + remote-endpoint = <&dsi0_out>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + ps8640_out: endpoint {
> + remote-endpoint = <&panel_in>;
> + };
> + };
> + };
> + };
> +};
> +
> +&i2c1 {
> + clock-frequency = <1500000>;
> + status = "okay";
> +
> + da9211: da9211@68 {
> + compatible = "dlg,da9211";
> + reg = <0x68>;
> +
no interrupts? binding description have this stated as required. what happens
when the device raises an interrupt?
> + regulators {
> + da9211_vcpu_reg: BUCKA {
> + regulator-name = "VBUCKA";
> + regulator-min-microvolt = < 700000>;
> + regulator-max-microvolt = <1310000>;
> + regulator-min-microamp = <2000000>;
> + regulator-max-microamp = <4400000>;
> + regulator-ramp-delay = <10000>;
> + regulator-always-on;
> + regulator-allowed-modes = <0 1>;
> + };
> +
> + da9211_vgpu_reg: BUCKB {
> + regulator-name = "VBUCKB";
> + regulator-min-microvolt = < 700000>;
> + regulator-max-microvolt = <1310000>;
> + regulator-min-microamp = <2000000>;
> + regulator-max-microamp = <3000000>;
> + regulator-ramp-delay = <10000>;
> + };
> + };
> + };
> +};
> +
> +&i2c2 {
> + status = "okay";
> +
> + tpm: tpm@20 {
> + compatible = "infineon,slb9645tt";
> + reg = <0x20>;
> + powered-while-suspended;
> + };
> +};
> +
> +&i2c3 {
> + clock-frequency = <400000>;
> + status = "okay";
> +
> + touchscreen: touchscreen@10 {
> + compatible = "elan,ekth3500";
> + reg = <0x10>;
> + interrupt-parent = <&pio>;
> + interrupts = <88 IRQ_TYPE_LEVEL_LOW>;
> + };
> +};
> +
> +&i2c4 {
> + clock-frequency = <400000>;
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&trackpad_irq>;
Why not move the pinctrl properties into the trackpad node?
> +
> + trackpad: trackpad@15 {
> + compatible = "elan,ekth3000";
> + interrupt-parent = <&pio>;
> + interrupts = <117 IRQ_TYPE_LEVEL_LOW>;
> + reg = <0x15>;
> + vcc-supply = <&mt6397_vgp6_reg>;
> + wakeup-source;
> + };
> +};
> +
> +&mipi_tx0 {
> + status = "okay";
> +};
> +
> +&mmc0 {
> + status = "okay";
> + pinctrl-names = "default", "state_uhs";
> + pinctrl-0 = <&mmc0_pins_default>;
> + pinctrl-1 = <&mmc0_pins_uhs>;
> + bus-width = <8>;
> + max-frequency = <200000000>;
> + cap-mmc-highspeed;
> + mmc-hs200-1_8v;
> + mmc-hs400-1_8v;
> + cap-mmc-hw-reset;
> + hs400-ds-delay = <0x14015>;
> + mediatek,hs200-cmd-int-delay=<30>;
> + mediatek,hs400-cmd-int-delay=<14>;
> + mediatek,hs400-cmd-resp-sel-rising;
> + vmmc-supply = <&mt6397_vemc_3v3_reg>;
> + vqmmc-supply = <&mt6397_vio18_reg>;
> + assigned-clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>;
> + assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL_D2>;
> + non-removable;
> +};
> +
> +&mmc1 {
> + status = "okay";
> + pinctrl-names = "default", "state_uhs";
> + pinctrl-0 = <&mmc1_pins_default>;
> + pinctrl-1 = <&mmc1_pins_uhs>;
> + bus-width = <4>;
> + max-frequency = <200000000>;
> + cap-sd-highspeed;
> + sd-uhs-sdr50;
> + sd-uhs-sdr104;
> + cd-gpios = <&pio 1 GPIO_ACTIVE_HIGH>;
> + vmmc-supply = <&mt6397_vmch_reg>;
> + vqmmc-supply = <&mt6397_vmc_reg>;
> +};
> +
> +&mmc3 {
> + status = "okay";
> + pinctrl-names = "default", "state_uhs";
> + pinctrl-0 = <&mmc3_pins_default>;
> + pinctrl-1 = <&mmc3_pins_uhs>;
> + bus-width = <4>;
> + max-frequency = <200000000>;
> + cap-sd-highspeed;
> + sd-uhs-sdr50;
> + sd-uhs-sdr104;
> + sdr104-clk-delay = <5>;
Not an upstream property, please delete it.
> + keep-power-in-suspend;
> + enable-sdio-wakeup;
> + cap-sdio-irq;
> + vmmc-supply = <&sdio_fixed_3v3>;
> + vqmmc-supply = <&mt6397_vgp3_reg>;
> + non-removable;
> + cap-power-off-card;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + btmrvl: btmrvl@2 {
> + compatible = "marvell,sd8897-bt";
> + reg = <2>;
> + interrupt-parent = <&pio>;
> + interrupts = <119 IRQ_TYPE_LEVEL_LOW>;
> + marvell,wakeup-pin = /bits/ 16 <0x0d>;
> + marvell,wakeup-gap-ms = /bits/ 16 <0x64>;
> + };
> +
> + mwifiex: mwifiex@1 {
> + compatible = "marvell,sd8897";
> + reg = <1>;
> + interrupt-parent = <&pio>;
> + interrupts = <38 IRQ_TYPE_LEVEL_LOW>;
> + marvell,wakeup-pin = <3>;
> + marvell,caldata_ed_mac = /bits/ 8 <
> +0x01 0x00 0x07 0x00 0x14 0x00 0x01 0x00 0x00 0x00 0x12 0x00 0x02 0x00 0x01 0x00
> +0x01 0x00 0x00 0x00 0x12 0x00 0x02 0x00 0x01 0x00
> + >;
Not an upstream property, please delete.
> + };
> +};
> +
> +&nor_flash {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&nor_gpio1_pins>;
> + bus-width = <8>;
> + max-frequency = <50000000>;
> + non-removable;
> + flash@0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + };
> +};
> +
> +&pio {
> + aud_i2s2: aud_i2s2 {
> + pins1 {
> + pinmux = <MT8173_PIN_128_I2S0_LRCK__FUNC_I2S1_WS>,
> + <MT8173_PIN_129_I2S0_BCK__FUNC_I2S1_BCK>,
> + <MT8173_PIN_130_I2S0_MCK__FUNC_I2S1_MCK>,
> + <MT8173_PIN_131_I2S0_DATA0__FUNC_I2S1_DO_1>,
> + <MT8173_PIN_12_EINT12__FUNC_I2S2_WS>,
> + <MT8173_PIN_13_EINT13__FUNC_I2S2_BCK>,
> + <MT8173_PIN_132_I2S0_DATA1__FUNC_I2S2_DI_2>;
> + bias-pull-down;
> + };
> + };
> +
> + bl_fixed_pins: bl_fixed_pins {
> + pins1 {
> + pinmux = <MT8173_PIN_32_UTXD2__FUNC_GPIO32>;
> + output-low;
> + };
> + };
> +
> + bt_wake_pins: bt_wake_pins {
> + pins1 {
> + pinmux = <MT8173_PIN_119_KPROW0__FUNC_GPIO119>;
> + bias-pull-up;
> + };
> + };
> +
> + disp_pwm0_pins: disp_pwm0_pins {
> + pins1 {
> + pinmux = <MT8173_PIN_87_DISP_PWM0__FUNC_DISP_PWM0>;
> + output-low;
> + };
> + };
> +
> + gpio_keys_pins: gpio_keys_pins {
> + volume_pins {
> + pinmux = <MT8173_PIN_123_KPCOL1__FUNC_GPIO123>,
> + <MT8173_PIN_124_KPCOL2__FUNC_GPIO124>;
> + bias-pull-up;
> + };
> +
> + tablet_mode_pins {
> + pinmux = <MT8173_PIN_121_KPROW2__FUNC_GPIO121>;
> + bias-pull-up;
> + };
> + };
> +
> + hdmi_mux_pins: hdmi_mux_pins {
> + pins1 {
> + pinmux = <MT8173_PIN_36_DAISYNC__FUNC_GPIO36>;
> + };
> + };
> +
> + mmc0_pins_default: mmc0default {
> + pins_cmd_dat {
> + pinmux = <MT8173_PIN_57_MSDC0_DAT0__FUNC_MSDC0_DAT0>,
> + <MT8173_PIN_58_MSDC0_DAT1__FUNC_MSDC0_DAT1>,
> + <MT8173_PIN_59_MSDC0_DAT2__FUNC_MSDC0_DAT2>,
> + <MT8173_PIN_60_MSDC0_DAT3__FUNC_MSDC0_DAT3>,
> + <MT8173_PIN_61_MSDC0_DAT4__FUNC_MSDC0_DAT4>,
> + <MT8173_PIN_62_MSDC0_DAT5__FUNC_MSDC0_DAT5>,
> + <MT8173_PIN_63_MSDC0_DAT6__FUNC_MSDC0_DAT6>,
> + <MT8173_PIN_64_MSDC0_DAT7__FUNC_MSDC0_DAT7>,
> + <MT8173_PIN_66_MSDC0_CMD__FUNC_MSDC0_CMD>;
> + bias-pull-up;
> + };
> +
> + pins_clk {
> + pinmux = <MT8173_PIN_65_MSDC0_CLK__FUNC_MSDC0_CLK>;
> + bias-pull-down;
identation.
> + };
> +
> + pins_rst {
> + pinmux = <MT8173_PIN_68_MSDC0_RST___FUNC_MSDC0_RSTB>;
> + bias-pull-up;
> + };
> + };
> +
> + mmc1_pins_default: mmc1default {
> + pins_cmd_dat {
> + pinmux = <MT8173_PIN_73_MSDC1_DAT0__FUNC_MSDC1_DAT0>,
> + <MT8173_PIN_74_MSDC1_DAT1__FUNC_MSDC1_DAT1>,
> + <MT8173_PIN_75_MSDC1_DAT2__FUNC_MSDC1_DAT2>,
> + <MT8173_PIN_76_MSDC1_DAT3__FUNC_MSDC1_DAT3>,
> + <MT8173_PIN_78_MSDC1_CMD__FUNC_MSDC1_CMD>;
> + input-enable;
> + drive-strength = <MTK_DRIVE_4mA>;
> + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
> + };
> +
> + pins_clk {
> + pinmux = <MT8173_PIN_77_MSDC1_CLK__FUNC_MSDC1_CLK>;
> + bias-pull-down;
> + drive-strength = <MTK_DRIVE_4mA>;
> + };
> +
> + pins_insert {
> + pinmux = <MT8173_PIN_1_EINT1__FUNC_GPIO1>;
> + bias-pull-up;
> + };
> + };
> +
> + mmc3_pins_default: mmc3default {
> + pins_dat {
> + pinmux = <MT8173_PIN_22_MSDC3_DAT0__FUNC_MSDC3_DAT0>,
> + <MT8173_PIN_23_MSDC3_DAT1__FUNC_MSDC3_DAT1>,
> + <MT8173_PIN_24_MSDC3_DAT2__FUNC_MSDC3_DAT2>,
> + <MT8173_PIN_25_MSDC3_DAT3__FUNC_MSDC3_DAT3>;
> + input-enable;
> + drive-strength = <MTK_DRIVE_8mA>;
> + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
> + };
> +
> + pins_cmd {
> + pinmux = <MT8173_PIN_27_MSDC3_CMD__FUNC_MSDC3_CMD>;
> + input-enable;
> + drive-strength = <MTK_DRIVE_8mA>;
> + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
> + };
> +
> + pins_clk {
> + pinmux = <MT8173_PIN_26_MSDC3_CLK__FUNC_MSDC3_CLK>;
> + bias-pull-down;
> + drive-strength = <MTK_DRIVE_8mA>;
> + };
> +
> + pins_pdn {
> + pinmux = <MT8173_PIN_85_AUD_DAT_MOSI__FUNC_GPIO85>;
> + output-low;
> + };
> + };
> +
> + mmc0_pins_uhs: mmc0 {
> + pins_cmd_dat {
> + pinmux = <MT8173_PIN_57_MSDC0_DAT0__FUNC_MSDC0_DAT0>,
> + <MT8173_PIN_58_MSDC0_DAT1__FUNC_MSDC0_DAT1>,
> + <MT8173_PIN_59_MSDC0_DAT2__FUNC_MSDC0_DAT2>,
> + <MT8173_PIN_60_MSDC0_DAT3__FUNC_MSDC0_DAT3>,
> + <MT8173_PIN_61_MSDC0_DAT4__FUNC_MSDC0_DAT4>,
> + <MT8173_PIN_62_MSDC0_DAT5__FUNC_MSDC0_DAT5>,
> + <MT8173_PIN_63_MSDC0_DAT6__FUNC_MSDC0_DAT6>,
> + <MT8173_PIN_64_MSDC0_DAT7__FUNC_MSDC0_DAT7>,
> + <MT8173_PIN_66_MSDC0_CMD__FUNC_MSDC0_CMD>;
> + input-enable;
> + drive-strength = <MTK_DRIVE_6mA>;
> + bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
> + };
> +
> + pins_clk {
> + pinmux = <MT8173_PIN_65_MSDC0_CLK__FUNC_MSDC0_CLK>;
> + drive-strength = <MTK_DRIVE_6mA>;
> + bias-pull-down = <MTK_PUPD_SET_R1R0_01>;
> + };
> +
> + pins_ds {
> + pinmux = <MT8173_PIN_67_MSDC0_DSL__FUNC_MSDC0_DSL>;
> + drive-strength = <MTK_DRIVE_10mA>;
> + bias-pull-down = <MTK_PUPD_SET_R1R0_01>;
> + };
> +
> + pins_rst {
> + pinmux = <MT8173_PIN_68_MSDC0_RST___FUNC_MSDC0_RSTB>;
> + bias-pull-up;
> + };
> + };
> +
> + mmc1_pins_uhs: mmc1 {
> + pins_cmd_dat {
> + pinmux = <MT8173_PIN_73_MSDC1_DAT0__FUNC_MSDC1_DAT0>,
> + <MT8173_PIN_74_MSDC1_DAT1__FUNC_MSDC1_DAT1>,
> + <MT8173_PIN_75_MSDC1_DAT2__FUNC_MSDC1_DAT2>,
> + <MT8173_PIN_76_MSDC1_DAT3__FUNC_MSDC1_DAT3>,
> + <MT8173_PIN_78_MSDC1_CMD__FUNC_MSDC1_CMD>;
> + input-enable;
> + drive-strength = <MTK_DRIVE_6mA>;
> + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
> + };
> +
> + pins_clk {
> + pinmux = <MT8173_PIN_77_MSDC1_CLK__FUNC_MSDC1_CLK>;
> + drive-strength = <MTK_DRIVE_8mA>;
> + bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
> + };
> + };
> +
> + mmc3_pins_uhs: mmc3 {
> + pins_dat {
> + pinmux = <MT8173_PIN_22_MSDC3_DAT0__FUNC_MSDC3_DAT0>,
> + <MT8173_PIN_23_MSDC3_DAT1__FUNC_MSDC3_DAT1>,
> + <MT8173_PIN_24_MSDC3_DAT2__FUNC_MSDC3_DAT2>,
> + <MT8173_PIN_25_MSDC3_DAT3__FUNC_MSDC3_DAT3>;
> + input-enable;
> + drive-strength = <MTK_DRIVE_8mA>;
> + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
> + };
> +
> + pins_cmd {
> + pinmux = <MT8173_PIN_27_MSDC3_CMD__FUNC_MSDC3_CMD>;
> + input-enable;
> + drive-strength = <MTK_DRIVE_8mA>;
> + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
> + };
> +
> + pins_clk {
> + pinmux = <MT8173_PIN_26_MSDC3_CLK__FUNC_MSDC3_CLK>;
> + drive-strength = <MTK_DRIVE_8mA>;
> + bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
> + };
> + };
> +
> + nor_gpio1_pins: nor {
> + pins1 {
> + pinmux = <MT8173_PIN_6_EINT6__FUNC_SFCS0>,
> + <MT8173_PIN_7_EINT7__FUNC_SFHOLD>,
> + <MT8173_PIN_8_EINT8__FUNC_SFIN>;
> + input-enable;
> + drive-strength = <MTK_DRIVE_4mA>;
> + bias-pull-up;
> + };
> +
> + pins2 {
> + pinmux = <MT8173_PIN_5_EINT5__FUNC_SFOUT>;
> + drive-strength = <MTK_DRIVE_4mA>;
> + bias-pull-up;
> + };
> +
> + pins_clk {
> + pinmux = <MT8173_PIN_9_EINT9__FUNC_SFCK>;
> + input-enable;
> + drive-strength = <MTK_DRIVE_4mA>;
> + bias-pull-up;
> + };
> + };
> +
> + panel_fixed_pins: panel_fixed_pins {
> + pins1 {
> + pinmux = <MT8173_PIN_41_CMMCLK__FUNC_GPIO41>;
> + };
> + };
> +
> + ps8640_pins: ps8640_pins {
> + pins1 {
> + pinmux = <MT8173_PIN_92_PCM_CLK__FUNC_GPIO92>,
> + <MT8173_PIN_115_URTS0__FUNC_GPIO115>,
> + <MT8173_PIN_127_LCM_RST__FUNC_GPIO127>;
> + };
> + };
> +
> + ps8640_fixed_pins: ps8640_fixed_pins {
> + pins1 {
> + pinmux = <MT8173_PIN_30_URTS2__FUNC_GPIO30>;
> + };
> + };
> +
> + rt5650_irq: rt5650_irq {
> + pins1 {
> + pinmux = <MT8173_PIN_3_EINT3__FUNC_GPIO3>;
> + bias-pull-down;
> + };
> + };
> +
> + spi_pins_a: spi1 {
> + pins1 {
> + pinmux = <MT8173_PIN_0_EINT0__FUNC_GPIO0>;
> + bias-pull-up;
> + };
> +
> + pins_spi {
> + pinmux = <MT8173_PIN_102_MSDC2_DAT2__FUNC_SPI_CK_1_>,
> + <MT8173_PIN_103_MSDC2_DAT3__FUNC_SPI_MI_1_>,
> + <MT8173_PIN_104_MSDC2_CLK__FUNC_SPI_MO_1_>,
> + <MT8173_PIN_105_MSDC2_CMD__FUNC_SPI_CS_1_>;
> + bias-disable;
> + };
> + };
> +
> + trackpad_irq: trackpad_irq {
> + pins1 {
> + pinmux = <MT8173_PIN_117_URXD3__FUNC_GPIO117>;
> + input-enable;
> + bias-pull-up;
> + };
> + };
> +
> + usb_pins: usb@0 {
> + pins1 {
> + pinmux = <MT8173_PIN_101_MSDC2_DAT1__FUNC_GPIO101>;
> + output-high;
> + bias-disable;
> + };
> + };
> +
> + wifi_wake_pins: wifi_wake_pins {
> + pins1 {
> + pinmux = <MT8173_PIN_38_CONN_RST__FUNC_GPIO38>;
> + bias-pull-up;
> + };
> + };
> +};
> +
> +&pwm0 {
> + status = "okay";
> +};
> +
> +&pwrap {
> + pmic: mt6397 {
> + compatible = "mediatek,mt6397";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + interrupt-parent = <&pio>;
> + interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> +
> + mt6397rtc: mt6397rtc {
AFAIK this should be
rtc: mt6397rtc {
Please fix that for all subnodes.
> + compatible = "mediatek,mt6397-rtc";
> + };
> +
> + syscfg_pctl_pmic: syscfg_pctl_pmic@c000 {
> + compatible = "mediatek,mt6397-pctl-pmic-syscfg",
> + "syscon";
> + reg = <0 0x0000c000 0 0x0108>;
not an upstream compatible, please delete the node.
> + };
> +
> + pio6397: pinctrl@c000 {
> + compatible = "mediatek,mt6397-pinctrl";
> + pins-are-numbered;
> + gpio-controller;
> + #gpio-cells = <2>;
> + };
> +
> + mt6397clock: mt6397clock {
> + compatible = "mediatek,mt6397-clk";
> + #clock-cells = <1>;
> + };
> +
> + mt6397regulator: mt6397regulator {
> + compatible = "mediatek,mt6397-regulator";
> +
> + mt6397_vpca15_reg: buck_vpca15 {
> + regulator-compatible = "buck_vpca15";
> + regulator-name = "vpca15";
> + regulator-min-microvolt = < 700000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <12500>;
> + regulator-always-on;
> + regulator-allowed-modes = <0 1>;
> + };
> +
> + mt6397_vpca7_reg: buck_vpca7 {
> + regulator-compatible = "buck_vpca7";
> + regulator-name = "vpca7";
> + regulator-min-microvolt = < 700000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <12500>;
> + regulator-enable-ramp-delay = <115>;
> + regulator-always-on;
> + };
> +
> + mt6397_vsramca15_reg: buck_vsramca15 {
> + regulator-compatible = "buck_vsramca15";
> + regulator-name = "vsramca15";
> + regulator-min-microvolt = < 700000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <12500>;
> + regulator-always-on;
> + };
> +
> + mt6397_vsramca7_reg: buck_vsramca7 {
> + regulator-compatible = "buck_vsramca7";
> + regulator-name = "vsramca7";
> + regulator-min-microvolt = < 700000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <12500>;
> + regulator-always-on;
> + };
> +
> + mt6397_vcore_reg: buck_vcore {
> + regulator-compatible = "buck_vcore";
> + regulator-name = "vcore";
> + regulator-min-microvolt = < 700000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <12500>;
> + regulator-always-on;
> + };
> +
> + mt6397_vgpu_reg: buck_vgpu {
> + regulator-compatible = "buck_vgpu";
> + regulator-name = "vgpu";
> + regulator-min-microvolt = < 700000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <12500>;
> + regulator-enable-ramp-delay = <115>;
> + };
> +
> + mt6397_vdrm_reg: buck_vdrm {
> + regulator-compatible = "buck_vdrm";
> + regulator-name = "vdrm";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1400000>;
> + regulator-ramp-delay = <12500>;
> + regulator-always-on;
> + };
> +
> + mt6397_vio18_reg: buck_vio18 {
> + regulator-compatible = "buck_vio18";
> + regulator-name = "vio18";
> + regulator-min-microvolt = <1620000>;
> + regulator-max-microvolt = <1980000>;
> + regulator-ramp-delay = <12500>;
> + regulator-always-on;
> + };
> +
> + mt6397_vtcxo_reg: ldo_vtcxo {
> + regulator-compatible = "ldo_vtcxo";
> + regulator-name = "vtcxo";
> + regulator-always-on;
> + };
> +
> + mt6397_va28_reg: ldo_va28 {
> + regulator-compatible = "ldo_va28";
> + regulator-name = "va28";
> + };
> +
> + mt6397_vcama_reg: ldo_vcama {
> + regulator-compatible = "ldo_vcama";
> + regulator-name = "vcama";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-enable-ramp-delay = <218>;
> + };
> +
> + mt6397_vio28_reg: ldo_vio28 {
> + regulator-compatible = "ldo_vio28";
> + regulator-name = "vio28";
> + regulator-always-on;
> + };
> +
> + mt6397_vusb_reg: ldo_vusb {
> + regulator-compatible = "ldo_vusb";
> + regulator-name = "vusb";
> + };
> +
> + mt6397_vmc_reg: ldo_vmc {
> + regulator-compatible = "ldo_vmc";
> + regulator-name = "vmc";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-enable-ramp-delay = <218>;
> + };
> +
> + mt6397_vmch_reg: ldo_vmch {
> + regulator-compatible = "ldo_vmch";
> + regulator-name = "vmch";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-enable-ramp-delay = <218>;
> + };
> +
> + mt6397_vemc_3v3_reg: ldo_vemc3v3 {
> + regulator-compatible = "ldo_vemc3v3";
> + regulator-name = "vemc_3v3";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-enable-ramp-delay = <218>;
> + };
> +
> + mt6397_vgp1_reg: ldo_vgp1 {
> + regulator-compatible = "ldo_vgp1";
> + regulator-name = "vcamd";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-enable-ramp-delay = <240>;
> + };
> +
> + mt6397_vgp2_reg: ldo_vgp2 {
> + regulator-compatible = "ldo_vgp2";
> + regulator-name = "vcamio";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-enable-ramp-delay = <218>;
> + };
> +
> + mt6397_vgp3_reg: ldo_vgp3 {
> + regulator-compatible = "ldo_vgp3";
> + regulator-name = "vcamaf";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-enable-ramp-delay = <218>;
> + };
> +
> + mt6397_vgp4_reg: ldo_vgp4 {
> + regulator-compatible = "ldo_vgp4";
> + regulator-name = "vgp4";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-enable-ramp-delay = <218>;
> + };
> +
> + mt6397_vgp5_reg: ldo_vgp5 {
> + regulator-compatible = "ldo_vgp5";
> + regulator-name = "vgp5";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-enable-ramp-delay = <218>;
> + };
> +
> + mt6397_vgp6_reg: ldo_vgp6 {
> + regulator-compatible = "ldo_vgp6";
> + regulator-name = "vgp6";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-enable-ramp-delay = <218>;
> + regulator-always-on;
> + };
> +
> + mt6397_vibr_reg: ldo_vibr {
> + regulator-compatible = "ldo_vibr";
> + regulator-name = "vibr";
> + regulator-min-microvolt = <1300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-enable-ramp-delay = <218>;
> + };
> + };
> + };
> +};
> +
> +&spi {
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi_pins_a>;
> + mediatek,pad-select = <1>;
> + status = "okay";
> + /* clients */
> + cros_ec: ec@0 {
> + compatible = "google,cros-ec-spi";
> + reg = <0x0>;
> + spi-max-frequency = <12000000>;
> + interrupt-parent = <&pio>;
> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> + google,cros-ec-spi-msg-delay = <500>;
> +
> + i2c_tunnel: i2c-tunnel@0 {
> + compatible = "google,cros-ec-i2c-tunnel";
> + google,remote-bus = <0>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + battery: sbs-battery@b {
> + compatible = "sbs,sbs-battery";
> + reg = <0xb>;
> + sbs,i2c-retry-count = <2>;
> + sbs,poll-retry-count = <1>;
> + };
> + };
> + };
> +};
> +
> +&thermal {
> + bank0-supply = <&mt6397_vpca15_reg>;
> + bank1-supply = <&da9211_vcpu_reg>;
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&ssusb {
> + dr_mode = "host";
> + wakeup-source;
> + vusb33-supply = <&mt6397_vusb_reg>;
> + status = "okay";
> +};
> +
> +&usb_host {
> + pinctrl-names = "default";
> + pinctrl-0 = <&usb_pins>;
> + vusb33-supply = <&mt6397_vusb_reg>;
> + status = "okay";
> +};
> +
> +#include "../../../../arm/boot/dts/cros-ec-keyboard.dtsi"
Why don't we use
#include <arm/cros-ec-keyboard.dtsi> ?
> \ No newline at end of file
>
As Yingjoe already mentioned, please add a newline :)
Regards,
Matthias
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH v2 2/2] arm64: dts: mediatek: add mt8173 elm and hana board
2020-01-10 7:37 ` [PATCH v2 2/2] arm64: dts: mediatek: add mt8173 elm and hana board Hsin-Yi Wang
2020-01-10 8:52 ` Yingjoe Chen
2020-01-10 13:42 ` Matthias Brugger
@ 2020-01-13 9:29 ` Enric Balletbo i Serra
2020-01-13 18:18 ` Matthias Kaehlcke
2 siblings, 1 reply; 14+ messages in thread
From: Enric Balletbo i Serra @ 2020-01-13 9:29 UTC (permalink / raw)
To: Hsin-Yi Wang, linux-arm-kernel
Cc: Mark Rutland, devicetree, Nicolas Boichat, linux-kernel,
Daniel Kurtz, Doug Anderson, Rob Herring, linux-mediatek,
Matthias Brugger, Matthias Kaehlcke
Hi Hsin-Yi,
Apart from the maintainer comments, a few more comments ...
cc'ing Matthias and Doug who I know played a bit with the pwm-backlight for the
uprev of the veyron devices, and you might be interested in his feedback in general.
On 10/1/20 8:37, Hsin-Yi Wang wrote:
> Elm is Acer Chromebook R13. Hana is Lenovo Chromebook. Both uses mt8173
> SoC.
>
> Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
> ---
> Changes in v2:
> - remove downstream nodes and unused nodes
> - use GPIO_ACTIVE_LOW for ps8640 gpios
> - move trackpad to hana
> ---
> arch/arm64/boot/dts/mediatek/Makefile | 3 +
> .../dts/mediatek/mt8173-elm-hana-rev7.dts | 27 +
> .../boot/dts/mediatek/mt8173-elm-hana.dts | 16 +
> .../boot/dts/mediatek/mt8173-elm-hana.dtsi | 60 +
> arch/arm64/boot/dts/mediatek/mt8173-elm.dts | 15 +
> arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi | 1040 +++++++++++++++++
> 6 files changed, 1161 insertions(+)
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dtsi
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm.dts
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi
>
> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> index 458bbc422a94..b45a45a565a1 100644
> --- a/arch/arm64/boot/dts/mediatek/Makefile
> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> @@ -6,5 +6,8 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana-rev7.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-evb.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-evb.dtb
> diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts
> new file mode 100644
> index 000000000000..a3616bc3d859
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts
> @@ -0,0 +1,27 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright 2019 MediaTek Inc.
> + */
> +
> +/dts-v1/;
> +#include "mt8173-elm-hana.dtsi"
> +
> +/ {
> + model = "Mediatek Hana rev7 board";
> + compatible = "google,hana-rev7", "mediatek,mt8173";
> +};
> +
> +&cpu_thermal {
> + trips {
> + cpu_crit: cpu_crit@0 {
> + temperature = <100000>;
> + type = "critical";
> + };
> + };
> +};
> +
> +&gpio_keys {
> + /delete-node/tablet_mode;
> + /delete-node/volume_down;
> + /delete-node/volume_up;
> +};
> \ No newline at end of file
> diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts
> new file mode 100644
> index 000000000000..8cbcc75192e3
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts
> @@ -0,0 +1,16 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright 2016 MediaTek Inc.
> + */
> +
> +/dts-v1/;
> +#include "mt8173-elm-hana.dtsi"
> +
> +/ {
> + model = "Mediatek Hana rev0 board";
> + compatible = "google,hana-rev6",
> + "google,hana-rev5", "google,hana-rev4",
> + "google,hana-rev3", "google,hana-rev2",
> + "google,hana-rev1", "google,hana-rev0",
> + "google,hana", "mediatek,mt8173";
nit: Usually we try to keep all aligned
> +};
> \ No newline at end of file
> diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dtsi b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dtsi
> new file mode 100644
> index 000000000000..35e12b290947
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dtsi
> @@ -0,0 +1,60 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright 2016 MediaTek Inc.
> + */
> +
> +#include "mt8173-elm.dtsi"
> +
> +&i2c0 {
> + clock-frequency = <200000>;
> +};
> +
> +&i2c3 {
> + touchscreen2: touchscreen@34 {
> + compatible = "melfas,mip4_ts";
> + reg = <0x34>;
> + interrupt-parent = <&pio>;
> + interrupts = <88 IRQ_TYPE_LEVEL_LOW>;
> + };
> +
> + touchscreen3: touchscreen@20 {
> + compatible = "hid-over-i2c";
> + reg = <0x20>;
> + hid-descr-addr = <0x0020>;
> + interrupt-parent = <&pio>;
> + interrupts = <88 IRQ_TYPE_LEVEL_LOW>;
> + };
That still looks weird to me. I don't have the touchscreen working yet so I can
really comment though.
> +};
> +
> +&i2c4 {
> + trackpad2: trackpad@2c {
> + compatible = "hid-over-i2c";
> + interrupt-parent = <&pio>;
> + interrupts = <117 IRQ_TYPE_LEVEL_LOW>;
> + reg = <0x2c>;
> + hid-descr-addr = <0x0020>;
> + wakeup-source;
The same for trackpads, still not working for me. There is no different
compatible to distinguish between the boards that have one or the other trackpad?
> + };
> +};
> +
> +&mmc1 {
> + wp-gpios = <&pio 42 GPIO_ACTIVE_HIGH>;
> +};
> +
> +&pio {
> + hdmi_mux_pins: hdmi_mux_pins {
> + pins2 {
> + pinmux = <MT8173_PIN_98_URTS1__FUNC_GPIO98>;
> + bias-pull-up;
> + output-high;
> + };
> + };
> +
> + mmc1_pins_default: mmc1default {
> + pins_wp {
> + pinmux = <MT8173_PIN_42_DSI_TE__FUNC_GPIO42>;
> + input-enable;
> + bias-pull-up;
> + };
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm.dts b/arch/arm64/boot/dts/mediatek/mt8173-elm.dts
> new file mode 100644
> index 000000000000..e5da2355760e
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8173-elm.dts
> @@ -0,0 +1,15 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright 2016 MediaTek Inc.
> + */
> +
> +/dts-v1/;
> +#include "mt8173-elm.dtsi"
> +
> +/ {
> + model = "Mediatek Elm board";
> + compatible = "google,elm-rev8", "google,elm-rev7", "google,elm-rev6",
> + "google,elm-rev5", "google,elm-rev4", "google,elm-rev3",
> + "google,elm-rev2", "google,elm-rev1",
> + "google,elm", "mediatek,mt8173";
nit: keep it aligned.
> +};
> \ No newline at end of file
> diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi b/arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi
> new file mode 100644
> index 000000000000..2ac738bebe04
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi
> @@ -0,0 +1,1040 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright 2016 MediaTek Inc.
> + */
> +
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/gpio/gpio.h>
> +#include "mt8173.dtsi"
> +
> +/ {
> + aliases {
> + serial0 = &uart0;
> + serial1 = &uart1;
> + serial2 = &uart2;
> + serial3 = &uart3;
> + };
I think this should be in mt8173.dtsi?
> +
> + memory@40000000 {
> + device_type = "memory";
> + reg = <0 0x40000000 0 0x80000000>;
> + };
> +
> + backlight_lcd: backlight_lcd {
nit: Not sure if you need to change or not, but this node is usually called
backlight: backlight without the _lcd. Note that this imply a userspace change
but /sys/class/backlight/backlight is more aligned with other boards (I guess)
when you have only one backlight. See for example:
git grep backlight arch/arm64/boot/*
> + compatible = "pwm-backlight";
> + pwms = <&pwm0 0 1000000>;
> + brightness-levels = <
> + 0 16 32 48 64 80 96 112
> + 128 144 160 176 192 208 224 240
> + 255
> + >;
> + default-brightness-level = <9>;
The reason you see the display too dark is because userspace sets and remembers
the default value you have using the above configuration which is only 16
levels. So after removing the two above properties you should set a new
brightness from userspace.
AFAIK 16 levels is not enough to have fancy backlight effects on Chrome OS
userspace, at least is not enough for Rockchip devices so I suppose is the same
for Mediatek.
You have to options here.
A) Remove brightness-levels and default-brightness-level. This will end with a
non-linear brightness curve for the backlight up to 4095 levels.
# cat max_brightness
4095
B) Use the num-interpolated-steps and default-brightness-level properties. This
will end with a linear curve brightness. Similar to what is done for veyron
devices but in this case with more levels because the PWM to control the
backlight is 16-bits instead of 8-bits for veyron devices.
*
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/arch/arm/boot/dts/rk3288-veyron-edp.dtsi#n42
My guess is that you're interested on option B here to be coherent with other
Chromebooks.
> + power-supply = <&bl_fixed_reg>;
> + enable-gpios = <&pio 95 GPIO_ACTIVE_HIGH>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&disp_pwm0_pins>;
> + status = "okay";
> + };
> +
> + bl_fixed_reg: fixedregulator@2 {
> + compatible = "regulator-fixed";
> + regulator-name = "bl_fixed";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + startup-delay-us = <1000>;
> + enable-active-high;
> + gpio = <&pio 32 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&bl_fixed_pins>;
> + };
> +
> + chosen {
> + stdout-path = &uart0;
You probably want stdout-path = "serial0:115200n8";
That way you'll get serial without needing to specify the console in the kernel
command line. Otherwise doesn't work because baudrate is missing.
> + };
> +
> + gpio_keys: gpio-keys {
> + compatible = "gpio-keys";
> + pinctrl-names = "default";
> + pinctrl-0 = <&gpio_keys_pins>;
> +
> + lid {
> + label = "Lid";
> + gpios = <&pio 69 GPIO_ACTIVE_LOW>;
> + linux,code = <0>; /* SW_LID */
> + linux,input-type = <5>; /* EV_SW */
> + gpio-key,wakeup;
> + };
> +
> + power {
> + label = "Power";
> + gpios = <&pio 14 GPIO_ACTIVE_HIGH>;
> + linux,code = <KEY_POWER>;
> + debounce-interval = <30>;
> + gpio-key,wakeup;
> + };
> +
> + tablet_mode {
> + label = "Tablet_mode";
> + gpios = <&pio 121 GPIO_ACTIVE_HIGH>;
> + linux,code = <1>; /* SW_TABLET_MODE */
> + linux,input-type = <5>; /* EV_SW */
> + gpio-key,wakeup;
> + };
> +
> + volume_down {
> + label = "Volume_down";
> + gpios = <&pio 123 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_VOLUMEDOWN>;
> + };
> +
> + volume_up {
> + label = "Volume_up";
> + gpios = <&pio 124 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_VOLUMEUP>;
> + };
> + };
> +
> + panel: panel {
> + compatible = "lg,lp120up1";
> + power-supply = <&panel_fixed_3v3>;
> + ddc-i2c-bus = <&i2c0>;
> + backlight = <&backlight_lcd>;
> +
> + port {
> + panel_in: endpoint {
> + remote-endpoint = <&ps8640_out>;
> + };
> + };
> + };
> +
> + panel_fixed_3v3: regulator@1 {
> + compatible = "regulator-fixed";
> + regulator-name = "PANEL_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + enable-active-high;
> + gpio = <&pio 41 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&panel_fixed_pins>;
> + };
> +
> + ps8640_fixed_1v2: regulator@2 {
> + compatible = "regulator-fixed";
> + regulator-name = "PS8640_1V2";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-enable-ramp-delay = <2000>;
> + enable-active-high;
> + regulator-boot-on;
> + gpio = <&pio 30 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&ps8640_fixed_pins>;
> + };
> +
> + sdio_fixed_3v3: fixedregulator@0 {
> + compatible = "regulator-fixed";
> + regulator-name = "3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&pio 85 GPIO_ACTIVE_HIGH>;
> + };
> +
> + sound: sound {
> + compatible = "mediatek,mt8173-rt5650";
> + mediatek,audio-codec = <&rt5650 &hdmi0>;
> + mediatek,platform = <&afe>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&aud_i2s2>;
> +
> + mediatek,mclk = <1>;
> + codec-capture {
> + sound-dai = <&rt5650 1>;
> + };
> + };
> +
> + hdmicon: connector {
> + compatible = "hdmi-connector";
> + label = "hdmi";
> + type = "a";
> + ddc-i2c-bus = <&hdmiddc0>;
> +
> + port {
> + hdmi_connector_in: endpoint {
> + remote-endpoint = <&hdmi0_out>;
> + };
> + };
> + };
> +};
> +
> +&cec {
> + status = "okay";
> +};
> +
> +&cpu0 {
> + proc-supply = <&mt6397_vpca15_reg>;
> +};
> +
> +&cpu1 {
> + proc-supply = <&mt6397_vpca15_reg>;
> +};
> +
> +&cpu2 {
> + proc-supply = <&da9211_vcpu_reg>;
> + sram-supply = <&mt6397_vsramca7_reg>;
> +};
> +
> +&cpu3 {
> + proc-supply = <&da9211_vcpu_reg>;
> + sram-supply = <&mt6397_vsramca7_reg>;
> +};
> +
> +&cpu_thermal {
> + sustainable-power = <4500>; /* milliwatts */
> + trips {
> + threshold: trip-point@0 {
> + temperature = <60000>;
> + };
> +
> + target: trip-point@1 {
> + temperature = <65000>;
> + };
> + };
> +};
> +
> +&dsi0 {
> + status = "okay";
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@1 {
> + dsi0_out: endpoint {
> + remote-endpoint = <&ps8640_in>;
> + };
> + };
> + };
> +};
> +
> +&dpi0 {
> + status = "okay";
> +};
> +
> +&hdmi0 {
> + status = "okay";
> + ports {
> + port@1 {
> + reg = <1>;
> +
> + hdmi0_out: endpoint {
> + remote-endpoint = <&hdmi_connector_in>;
> + };
> + };
> + };
> +};
> +
> +&hdmi_phy {
> + status = "okay";
> + mediatek,ibias = <0xc>;
> +};
> +
> +&i2c0 {
> + status = "okay";
> +
> + rt5650: audio-codec@1a {
> + compatible = "realtek,rt5650";
> + reg = <0x1a>;
> + avdd-supply = <&mt6397_vgp1_reg>;
> + cpvdd-supply = <&mt6397_vcama_reg>;
> + interrupt-parent = <&pio>;
> + interrupts = <3 IRQ_TYPE_EDGE_BOTH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&rt5650_irq>;
> + #sound-dai-cells = <1>;
> + realtek,dmic1-data-pin = <2>;
> + realtek,jd-mode = <2>;
> + };
> +
> + ps8640: edp-bridge@8 {
> + compatible = "parade,ps8640";
> + reg = <0x8>;
> + powerdown-gpios = <&pio 127 GPIO_ACTIVE_LOW>;
> + reset-gpios = <&pio 115 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&ps8640_pins>;
> + vdd12-supply = <&ps8640_fixed_1v2>;
> + vdd33-supply = <&mt6397_vgp2_reg>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + ps8640_in: endpoint {
> + remote-endpoint = <&dsi0_out>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + ps8640_out: endpoint {
> + remote-endpoint = <&panel_in>;
> + };
> + };
> + };
> + };
> +};
> +
> +&i2c1 {
> + clock-frequency = <1500000>;
> + status = "okay";
> +
> + da9211: da9211@68 {
> + compatible = "dlg,da9211";
> + reg = <0x68>;
> +
> + regulators {
> + da9211_vcpu_reg: BUCKA {
> + regulator-name = "VBUCKA";
> + regulator-min-microvolt = < 700000>;
> + regulator-max-microvolt = <1310000>;
> + regulator-min-microamp = <2000000>;
> + regulator-max-microamp = <4400000>;
> + regulator-ramp-delay = <10000>;
> + regulator-always-on;
> + regulator-allowed-modes = <0 1>;
> + };
> +
> + da9211_vgpu_reg: BUCKB {
> + regulator-name = "VBUCKB";
> + regulator-min-microvolt = < 700000>;
> + regulator-max-microvolt = <1310000>;
> + regulator-min-microamp = <2000000>;
> + regulator-max-microamp = <3000000>;
> + regulator-ramp-delay = <10000>;
> + };
> + };
> + };
> +};
> +
> +&i2c2 {
> + status = "okay";
> +
> + tpm: tpm@20 {
> + compatible = "infineon,slb9645tt";
> + reg = <0x20>;
> + powered-while-suspended;
> + };
> +};
> +
> +&i2c3 {
> + clock-frequency = <400000>;
> + status = "okay";
> +
> + touchscreen: touchscreen@10 {
> + compatible = "elan,ekth3500";
> + reg = <0x10>;
> + interrupt-parent = <&pio>;
> + interrupts = <88 IRQ_TYPE_LEVEL_LOW>;
> + };
> +};
> +
> +&i2c4 {
> + clock-frequency = <400000>;
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&trackpad_irq>;
> +
> + trackpad: trackpad@15 {
> + compatible = "elan,ekth3000";
> + interrupt-parent = <&pio>;
> + interrupts = <117 IRQ_TYPE_LEVEL_LOW>;
> + reg = <0x15>;
> + vcc-supply = <&mt6397_vgp6_reg>;
> + wakeup-source;
> + };
> +};
> +
> +&mipi_tx0 {
> + status = "okay";
> +};
> +
> +&mmc0 {
> + status = "okay";
> + pinctrl-names = "default", "state_uhs";
> + pinctrl-0 = <&mmc0_pins_default>;
> + pinctrl-1 = <&mmc0_pins_uhs>;
> + bus-width = <8>;
> + max-frequency = <200000000>;
> + cap-mmc-highspeed;
> + mmc-hs200-1_8v;
> + mmc-hs400-1_8v;
> + cap-mmc-hw-reset;
> + hs400-ds-delay = <0x14015>;
> + mediatek,hs200-cmd-int-delay=<30>;
> + mediatek,hs400-cmd-int-delay=<14>;
> + mediatek,hs400-cmd-resp-sel-rising;
> + vmmc-supply = <&mt6397_vemc_3v3_reg>;
> + vqmmc-supply = <&mt6397_vio18_reg>;
> + assigned-clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>;
> + assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL_D2>;
> + non-removable;
> +};
> +
> +&mmc1 {
> + status = "okay";
> + pinctrl-names = "default", "state_uhs";
> + pinctrl-0 = <&mmc1_pins_default>;
> + pinctrl-1 = <&mmc1_pins_uhs>;
> + bus-width = <4>;
> + max-frequency = <200000000>;
> + cap-sd-highspeed;
> + sd-uhs-sdr50;
> + sd-uhs-sdr104;
> + cd-gpios = <&pio 1 GPIO_ACTIVE_HIGH>;
Is this really a GPIO_ACTIVE_HIGH?
I still have problems with this, I need to comment this line and add
non-removable as a workaround in order to boot from the SD-card.
I think that the problem is that is GPIO_ACTIVE_LOW (it works for me, but I
don't have the schematics to confirm)
> + vmmc-supply = <&mt6397_vmch_reg>;
> + vqmmc-supply = <&mt6397_vmc_reg>;
> +};
> +
> +&mmc3 {
> + status = "okay";
> + pinctrl-names = "default", "state_uhs";
> + pinctrl-0 = <&mmc3_pins_default>;
> + pinctrl-1 = <&mmc3_pins_uhs>;
> + bus-width = <4>;
> + max-frequency = <200000000>;
> + cap-sd-highspeed;
> + sd-uhs-sdr50;
> + sd-uhs-sdr104;
> + sdr104-clk-delay = <5>;
> + keep-power-in-suspend;
> + enable-sdio-wakeup;
> + cap-sdio-irq;
> + vmmc-supply = <&sdio_fixed_3v3>;
> + vqmmc-supply = <&mt6397_vgp3_reg>;
> + non-removable;
> + cap-power-off-card;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + btmrvl: btmrvl@2 {
> + compatible = "marvell,sd8897-bt";
> + reg = <2>;
> + interrupt-parent = <&pio>;
> + interrupts = <119 IRQ_TYPE_LEVEL_LOW>;
> + marvell,wakeup-pin = /bits/ 16 <0x0d>;
> + marvell,wakeup-gap-ms = /bits/ 16 <0x64>;
> + };
> +
> + mwifiex: mwifiex@1 {
> + compatible = "marvell,sd8897";
> + reg = <1>;
> + interrupt-parent = <&pio>;
> + interrupts = <38 IRQ_TYPE_LEVEL_LOW>;
> + marvell,wakeup-pin = <3>;
> + marvell,caldata_ed_mac = /bits/ 8 <
> +0x01 0x00 0x07 0x00 0x14 0x00 0x01 0x00 0x00 0x00 0x12 0x00 0x02 0x00 0x01 0x00
> +0x01 0x00 0x00 0x00 0x12 0x00 0x02 0x00 0x01 0x00
> + >;
> + };
> +};
> +
> +&nor_flash {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&nor_gpio1_pins>;
> + bus-width = <8>;
> + max-frequency = <50000000>;
> + non-removable;
> + flash@0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + };
> +};
> +
> +&pio {
> + aud_i2s2: aud_i2s2 {
> + pins1 {
> + pinmux = <MT8173_PIN_128_I2S0_LRCK__FUNC_I2S1_WS>,
> + <MT8173_PIN_129_I2S0_BCK__FUNC_I2S1_BCK>,
> + <MT8173_PIN_130_I2S0_MCK__FUNC_I2S1_MCK>,
> + <MT8173_PIN_131_I2S0_DATA0__FUNC_I2S1_DO_1>,
> + <MT8173_PIN_12_EINT12__FUNC_I2S2_WS>,
> + <MT8173_PIN_13_EINT13__FUNC_I2S2_BCK>,
> + <MT8173_PIN_132_I2S0_DATA1__FUNC_I2S2_DI_2>;
> + bias-pull-down;
> + };
> + };
> +
> + bl_fixed_pins: bl_fixed_pins {
> + pins1 {
> + pinmux = <MT8173_PIN_32_UTXD2__FUNC_GPIO32>;
> + output-low;
> + };
> + };
> +
> + bt_wake_pins: bt_wake_pins {
> + pins1 {
> + pinmux = <MT8173_PIN_119_KPROW0__FUNC_GPIO119>;
> + bias-pull-up;
> + };
> + };
> +
> + disp_pwm0_pins: disp_pwm0_pins {
> + pins1 {
> + pinmux = <MT8173_PIN_87_DISP_PWM0__FUNC_DISP_PWM0>;
> + output-low;
> + };
> + };
> +
> + gpio_keys_pins: gpio_keys_pins {
> + volume_pins {
> + pinmux = <MT8173_PIN_123_KPCOL1__FUNC_GPIO123>,
> + <MT8173_PIN_124_KPCOL2__FUNC_GPIO124>;
> + bias-pull-up;
> + };
> +
> + tablet_mode_pins {
> + pinmux = <MT8173_PIN_121_KPROW2__FUNC_GPIO121>;
> + bias-pull-up;
> + };
> + };
> +
> + hdmi_mux_pins: hdmi_mux_pins {
> + pins1 {
> + pinmux = <MT8173_PIN_36_DAISYNC__FUNC_GPIO36>;
> + };
> + };
> +
> + mmc0_pins_default: mmc0default {
> + pins_cmd_dat {
> + pinmux = <MT8173_PIN_57_MSDC0_DAT0__FUNC_MSDC0_DAT0>,
> + <MT8173_PIN_58_MSDC0_DAT1__FUNC_MSDC0_DAT1>,
> + <MT8173_PIN_59_MSDC0_DAT2__FUNC_MSDC0_DAT2>,
> + <MT8173_PIN_60_MSDC0_DAT3__FUNC_MSDC0_DAT3>,
> + <MT8173_PIN_61_MSDC0_DAT4__FUNC_MSDC0_DAT4>,
> + <MT8173_PIN_62_MSDC0_DAT5__FUNC_MSDC0_DAT5>,
> + <MT8173_PIN_63_MSDC0_DAT6__FUNC_MSDC0_DAT6>,
> + <MT8173_PIN_64_MSDC0_DAT7__FUNC_MSDC0_DAT7>,
> + <MT8173_PIN_66_MSDC0_CMD__FUNC_MSDC0_CMD>;
> + bias-pull-up;
> + };
> +
> + pins_clk {
> + pinmux = <MT8173_PIN_65_MSDC0_CLK__FUNC_MSDC0_CLK>;
> + bias-pull-down;
> + };
> +
> + pins_rst {
> + pinmux = <MT8173_PIN_68_MSDC0_RST___FUNC_MSDC0_RSTB>;
> + bias-pull-up;
> + };
> + };
> +
> + mmc1_pins_default: mmc1default {
> + pins_cmd_dat {
> + pinmux = <MT8173_PIN_73_MSDC1_DAT0__FUNC_MSDC1_DAT0>,
> + <MT8173_PIN_74_MSDC1_DAT1__FUNC_MSDC1_DAT1>,
> + <MT8173_PIN_75_MSDC1_DAT2__FUNC_MSDC1_DAT2>,
> + <MT8173_PIN_76_MSDC1_DAT3__FUNC_MSDC1_DAT3>,
> + <MT8173_PIN_78_MSDC1_CMD__FUNC_MSDC1_CMD>;
> + input-enable;
> + drive-strength = <MTK_DRIVE_4mA>;
> + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
> + };
> +
> + pins_clk {
> + pinmux = <MT8173_PIN_77_MSDC1_CLK__FUNC_MSDC1_CLK>;
> + bias-pull-down;
> + drive-strength = <MTK_DRIVE_4mA>;
> + };
> +
> + pins_insert {
> + pinmux = <MT8173_PIN_1_EINT1__FUNC_GPIO1>;
> + bias-pull-up;
> + };
> + };
> +
> + mmc3_pins_default: mmc3default {
> + pins_dat {
> + pinmux = <MT8173_PIN_22_MSDC3_DAT0__FUNC_MSDC3_DAT0>,
> + <MT8173_PIN_23_MSDC3_DAT1__FUNC_MSDC3_DAT1>,
> + <MT8173_PIN_24_MSDC3_DAT2__FUNC_MSDC3_DAT2>,
> + <MT8173_PIN_25_MSDC3_DAT3__FUNC_MSDC3_DAT3>;
> + input-enable;
> + drive-strength = <MTK_DRIVE_8mA>;
> + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
> + };
> +
> + pins_cmd {
> + pinmux = <MT8173_PIN_27_MSDC3_CMD__FUNC_MSDC3_CMD>;
> + input-enable;
> + drive-strength = <MTK_DRIVE_8mA>;
> + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
> + };
> +
> + pins_clk {
> + pinmux = <MT8173_PIN_26_MSDC3_CLK__FUNC_MSDC3_CLK>;
> + bias-pull-down;
> + drive-strength = <MTK_DRIVE_8mA>;
> + };
> +
> + pins_pdn {
> + pinmux = <MT8173_PIN_85_AUD_DAT_MOSI__FUNC_GPIO85>;
> + output-low;
> + };
> + };
> +
> + mmc0_pins_uhs: mmc0 {
> + pins_cmd_dat {
> + pinmux = <MT8173_PIN_57_MSDC0_DAT0__FUNC_MSDC0_DAT0>,
> + <MT8173_PIN_58_MSDC0_DAT1__FUNC_MSDC0_DAT1>,
> + <MT8173_PIN_59_MSDC0_DAT2__FUNC_MSDC0_DAT2>,
> + <MT8173_PIN_60_MSDC0_DAT3__FUNC_MSDC0_DAT3>,
> + <MT8173_PIN_61_MSDC0_DAT4__FUNC_MSDC0_DAT4>,
> + <MT8173_PIN_62_MSDC0_DAT5__FUNC_MSDC0_DAT5>,
> + <MT8173_PIN_63_MSDC0_DAT6__FUNC_MSDC0_DAT6>,
> + <MT8173_PIN_64_MSDC0_DAT7__FUNC_MSDC0_DAT7>,
> + <MT8173_PIN_66_MSDC0_CMD__FUNC_MSDC0_CMD>;
> + input-enable;
> + drive-strength = <MTK_DRIVE_6mA>;
> + bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
> + };
> +
> + pins_clk {
> + pinmux = <MT8173_PIN_65_MSDC0_CLK__FUNC_MSDC0_CLK>;
> + drive-strength = <MTK_DRIVE_6mA>;
> + bias-pull-down = <MTK_PUPD_SET_R1R0_01>;
> + };
> +
> + pins_ds {
> + pinmux = <MT8173_PIN_67_MSDC0_DSL__FUNC_MSDC0_DSL>;
> + drive-strength = <MTK_DRIVE_10mA>;
> + bias-pull-down = <MTK_PUPD_SET_R1R0_01>;
> + };
> +
> + pins_rst {
> + pinmux = <MT8173_PIN_68_MSDC0_RST___FUNC_MSDC0_RSTB>;
> + bias-pull-up;
> + };
> + };
> +
> + mmc1_pins_uhs: mmc1 {
> + pins_cmd_dat {
> + pinmux = <MT8173_PIN_73_MSDC1_DAT0__FUNC_MSDC1_DAT0>,
> + <MT8173_PIN_74_MSDC1_DAT1__FUNC_MSDC1_DAT1>,
> + <MT8173_PIN_75_MSDC1_DAT2__FUNC_MSDC1_DAT2>,
> + <MT8173_PIN_76_MSDC1_DAT3__FUNC_MSDC1_DAT3>,
> + <MT8173_PIN_78_MSDC1_CMD__FUNC_MSDC1_CMD>;
> + input-enable;
> + drive-strength = <MTK_DRIVE_6mA>;
> + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
> + };
> +
> + pins_clk {
> + pinmux = <MT8173_PIN_77_MSDC1_CLK__FUNC_MSDC1_CLK>;
> + drive-strength = <MTK_DRIVE_8mA>;
> + bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
> + };
> + };
> +
> + mmc3_pins_uhs: mmc3 {
> + pins_dat {
> + pinmux = <MT8173_PIN_22_MSDC3_DAT0__FUNC_MSDC3_DAT0>,
> + <MT8173_PIN_23_MSDC3_DAT1__FUNC_MSDC3_DAT1>,
> + <MT8173_PIN_24_MSDC3_DAT2__FUNC_MSDC3_DAT2>,
> + <MT8173_PIN_25_MSDC3_DAT3__FUNC_MSDC3_DAT3>;
> + input-enable;
> + drive-strength = <MTK_DRIVE_8mA>;
> + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
> + };
> +
> + pins_cmd {
> + pinmux = <MT8173_PIN_27_MSDC3_CMD__FUNC_MSDC3_CMD>;
> + input-enable;
> + drive-strength = <MTK_DRIVE_8mA>;
> + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
> + };
> +
> + pins_clk {
> + pinmux = <MT8173_PIN_26_MSDC3_CLK__FUNC_MSDC3_CLK>;
> + drive-strength = <MTK_DRIVE_8mA>;
> + bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
> + };
> + };
> +
> + nor_gpio1_pins: nor {
> + pins1 {
> + pinmux = <MT8173_PIN_6_EINT6__FUNC_SFCS0>,
> + <MT8173_PIN_7_EINT7__FUNC_SFHOLD>,
> + <MT8173_PIN_8_EINT8__FUNC_SFIN>;
> + input-enable;
> + drive-strength = <MTK_DRIVE_4mA>;
> + bias-pull-up;
> + };
> +
> + pins2 {
> + pinmux = <MT8173_PIN_5_EINT5__FUNC_SFOUT>;
> + drive-strength = <MTK_DRIVE_4mA>;
> + bias-pull-up;
> + };
> +
> + pins_clk {
> + pinmux = <MT8173_PIN_9_EINT9__FUNC_SFCK>;
> + input-enable;
> + drive-strength = <MTK_DRIVE_4mA>;
> + bias-pull-up;
> + };
> + };
> +
> + panel_fixed_pins: panel_fixed_pins {
> + pins1 {
> + pinmux = <MT8173_PIN_41_CMMCLK__FUNC_GPIO41>;
> + };
> + };
> +
> + ps8640_pins: ps8640_pins {
> + pins1 {
> + pinmux = <MT8173_PIN_92_PCM_CLK__FUNC_GPIO92>,
> + <MT8173_PIN_115_URTS0__FUNC_GPIO115>,
> + <MT8173_PIN_127_LCM_RST__FUNC_GPIO127>;
> + };
> + };
> +
> + ps8640_fixed_pins: ps8640_fixed_pins {
> + pins1 {
> + pinmux = <MT8173_PIN_30_URTS2__FUNC_GPIO30>;
> + };
> + };
> +
> + rt5650_irq: rt5650_irq {
> + pins1 {
> + pinmux = <MT8173_PIN_3_EINT3__FUNC_GPIO3>;
> + bias-pull-down;
> + };
> + };
> +
> + spi_pins_a: spi1 {
> + pins1 {
> + pinmux = <MT8173_PIN_0_EINT0__FUNC_GPIO0>;
> + bias-pull-up;
> + };
> +
> + pins_spi {
> + pinmux = <MT8173_PIN_102_MSDC2_DAT2__FUNC_SPI_CK_1_>,
> + <MT8173_PIN_103_MSDC2_DAT3__FUNC_SPI_MI_1_>,
> + <MT8173_PIN_104_MSDC2_CLK__FUNC_SPI_MO_1_>,
> + <MT8173_PIN_105_MSDC2_CMD__FUNC_SPI_CS_1_>;
> + bias-disable;
> + };
> + };
> +
> + trackpad_irq: trackpad_irq {
> + pins1 {
> + pinmux = <MT8173_PIN_117_URXD3__FUNC_GPIO117>;
> + input-enable;
> + bias-pull-up;
> + };
> + };
> +
> + usb_pins: usb@0 {
> + pins1 {
> + pinmux = <MT8173_PIN_101_MSDC2_DAT1__FUNC_GPIO101>;
> + output-high;
> + bias-disable;
> + };
> + };
> +
> + wifi_wake_pins: wifi_wake_pins {
> + pins1 {
> + pinmux = <MT8173_PIN_38_CONN_RST__FUNC_GPIO38>;
> + bias-pull-up;
> + };
> + };
> +};
> +
> +&pwm0 {
> + status = "okay";
> +};
> +
> +&pwrap {
> + pmic: mt6397 {
> + compatible = "mediatek,mt6397";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + interrupt-parent = <&pio>;
> + interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> +
> + mt6397rtc: mt6397rtc {
> + compatible = "mediatek,mt6397-rtc";
> + };
> +
> + syscfg_pctl_pmic: syscfg_pctl_pmic@c000 {
> + compatible = "mediatek,mt6397-pctl-pmic-syscfg",
> + "syscon";
> + reg = <0 0x0000c000 0 0x0108>;
> + };
> +
> + pio6397: pinctrl@c000 {
> + compatible = "mediatek,mt6397-pinctrl";
> + pins-are-numbered;
> + gpio-controller;
> + #gpio-cells = <2>;
> + };
> +
> + mt6397clock: mt6397clock {
> + compatible = "mediatek,mt6397-clk";
> + #clock-cells = <1>;
> + };
> +
> + mt6397regulator: mt6397regulator {
> + compatible = "mediatek,mt6397-regulator";
> +
> + mt6397_vpca15_reg: buck_vpca15 {
> + regulator-compatible = "buck_vpca15";
> + regulator-name = "vpca15";
> + regulator-min-microvolt = < 700000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <12500>;
> + regulator-always-on;
> + regulator-allowed-modes = <0 1>;
> + };
> +
> + mt6397_vpca7_reg: buck_vpca7 {
> + regulator-compatible = "buck_vpca7";
> + regulator-name = "vpca7";
> + regulator-min-microvolt = < 700000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <12500>;
> + regulator-enable-ramp-delay = <115>;
> + regulator-always-on;
> + };
> +
> + mt6397_vsramca15_reg: buck_vsramca15 {
> + regulator-compatible = "buck_vsramca15";
> + regulator-name = "vsramca15";
> + regulator-min-microvolt = < 700000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <12500>;
> + regulator-always-on;
> + };
> +
> + mt6397_vsramca7_reg: buck_vsramca7 {
> + regulator-compatible = "buck_vsramca7";
> + regulator-name = "vsramca7";
> + regulator-min-microvolt = < 700000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <12500>;
> + regulator-always-on;
> + };
> +
> + mt6397_vcore_reg: buck_vcore {
> + regulator-compatible = "buck_vcore";
> + regulator-name = "vcore";
> + regulator-min-microvolt = < 700000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <12500>;
> + regulator-always-on;
> + };
> +
> + mt6397_vgpu_reg: buck_vgpu {
> + regulator-compatible = "buck_vgpu";
> + regulator-name = "vgpu";
> + regulator-min-microvolt = < 700000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <12500>;
> + regulator-enable-ramp-delay = <115>;
> + };
> +
> + mt6397_vdrm_reg: buck_vdrm {
> + regulator-compatible = "buck_vdrm";
> + regulator-name = "vdrm";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1400000>;
> + regulator-ramp-delay = <12500>;
> + regulator-always-on;
> + };
> +
> + mt6397_vio18_reg: buck_vio18 {
> + regulator-compatible = "buck_vio18";
> + regulator-name = "vio18";
> + regulator-min-microvolt = <1620000>;
> + regulator-max-microvolt = <1980000>;
> + regulator-ramp-delay = <12500>;
> + regulator-always-on;
> + };
> +
> + mt6397_vtcxo_reg: ldo_vtcxo {
> + regulator-compatible = "ldo_vtcxo";
> + regulator-name = "vtcxo";
> + regulator-always-on;
> + };
> +
> + mt6397_va28_reg: ldo_va28 {
> + regulator-compatible = "ldo_va28";
> + regulator-name = "va28";
> + };
> +
> + mt6397_vcama_reg: ldo_vcama {
> + regulator-compatible = "ldo_vcama";
> + regulator-name = "vcama";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-enable-ramp-delay = <218>;
> + };
> +
> + mt6397_vio28_reg: ldo_vio28 {
> + regulator-compatible = "ldo_vio28";
> + regulator-name = "vio28";
> + regulator-always-on;
> + };
> +
> + mt6397_vusb_reg: ldo_vusb {
> + regulator-compatible = "ldo_vusb";
> + regulator-name = "vusb";
> + };
> +
> + mt6397_vmc_reg: ldo_vmc {
> + regulator-compatible = "ldo_vmc";
> + regulator-name = "vmc";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-enable-ramp-delay = <218>;
> + };
> +
> + mt6397_vmch_reg: ldo_vmch {
> + regulator-compatible = "ldo_vmch";
> + regulator-name = "vmch";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-enable-ramp-delay = <218>;
> + };
> +
> + mt6397_vemc_3v3_reg: ldo_vemc3v3 {
> + regulator-compatible = "ldo_vemc3v3";
> + regulator-name = "vemc_3v3";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-enable-ramp-delay = <218>;
> + };
> +
> + mt6397_vgp1_reg: ldo_vgp1 {
> + regulator-compatible = "ldo_vgp1";
> + regulator-name = "vcamd";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-enable-ramp-delay = <240>;
> + };
> +
> + mt6397_vgp2_reg: ldo_vgp2 {
> + regulator-compatible = "ldo_vgp2";
> + regulator-name = "vcamio";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-enable-ramp-delay = <218>;
> + };
> +
> + mt6397_vgp3_reg: ldo_vgp3 {
> + regulator-compatible = "ldo_vgp3";
> + regulator-name = "vcamaf";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-enable-ramp-delay = <218>;
> + };
> +
> + mt6397_vgp4_reg: ldo_vgp4 {
> + regulator-compatible = "ldo_vgp4";
> + regulator-name = "vgp4";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-enable-ramp-delay = <218>;
> + };
> +
> + mt6397_vgp5_reg: ldo_vgp5 {
> + regulator-compatible = "ldo_vgp5";
> + regulator-name = "vgp5";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-enable-ramp-delay = <218>;
> + };
> +
> + mt6397_vgp6_reg: ldo_vgp6 {
> + regulator-compatible = "ldo_vgp6";
> + regulator-name = "vgp6";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-enable-ramp-delay = <218>;
> + regulator-always-on;
> + };
> +
> + mt6397_vibr_reg: ldo_vibr {
> + regulator-compatible = "ldo_vibr";
> + regulator-name = "vibr";
> + regulator-min-microvolt = <1300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-enable-ramp-delay = <218>;
> + };
> + };
> + };
> +};
> +
> +&spi {
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi_pins_a>;
> + mediatek,pad-select = <1>;
> + status = "okay";
> + /* clients */
> + cros_ec: ec@0 {
> + compatible = "google,cros-ec-spi";
> + reg = <0x0>;
> + spi-max-frequency = <12000000>;
> + interrupt-parent = <&pio>;
> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> + google,cros-ec-spi-msg-delay = <500>;
> +
> + i2c_tunnel: i2c-tunnel@0 {
> + compatible = "google,cros-ec-i2c-tunnel";
> + google,remote-bus = <0>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + battery: sbs-battery@b {
> + compatible = "sbs,sbs-battery";
> + reg = <0xb>;
> + sbs,i2c-retry-count = <2>;
> + sbs,poll-retry-count = <1>;
> + };
> + };
> + };
> +};
> +
> +&thermal {
> + bank0-supply = <&mt6397_vpca15_reg>;
> + bank1-supply = <&da9211_vcpu_reg>;
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&ssusb {
> + dr_mode = "host";
> + wakeup-source;
> + vusb33-supply = <&mt6397_vusb_reg>;
> + status = "okay";
> +};
> +
> +&usb_host {
> + pinctrl-names = "default";
> + pinctrl-0 = <&usb_pins>;
> + vusb33-supply = <&mt6397_vusb_reg>;
> + status = "okay";
> +};
> +
> +#include "../../../../arm/boot/dts/cros-ec-keyboard.dtsi"
> \ No newline at end of file
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH v2 2/2] arm64: dts: mediatek: add mt8173 elm and hana board
2020-01-10 13:42 ` Matthias Brugger
@ 2020-01-13 18:01 ` Hsin-Yi Wang
2020-01-14 15:10 ` Matthias Brugger
0 siblings, 1 reply; 14+ messages in thread
From: Hsin-Yi Wang @ 2020-01-13 18:01 UTC (permalink / raw)
To: Matthias Brugger
Cc: Mark Rutland, Devicetree List, Nicolas Boichat, lkml,
Daniel Kurtz, Rob Herring, linux-mediatek,
Enric Balletbo i Serra,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE
On Fri, Jan 10, 2020 at 9:42 PM Matthias Brugger <matthias.bgg@gmail.com> wrote:
>
>
Thanks, I will address the comments and send next version
>
> On 10/01/2020 08:37, Hsin-Yi Wang wrote:
> > Elm is Acer Chromebook R13. Hana is Lenovo Chromebook. Both uses mt8173
> > SoC.
> >
> > Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
> > ---
> > Changes in v2:
> > - remove downstream nodes and unused nodes
> > - use GPIO_ACTIVE_LOW for ps8640 gpios
> > - move trackpad to hana
> > ---
> > arch/arm64/boot/dts/mediatek/Makefile | 3 +
> > .../dts/mediatek/mt8173-elm-hana-rev7.dts | 27 +
> > .../boot/dts/mediatek/mt8173-elm-hana.dts | 16 +
> > .../boot/dts/mediatek/mt8173-elm-hana.dtsi | 60 +
> > arch/arm64/boot/dts/mediatek/mt8173-elm.dts | 15 +
> > arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi | 1040 +++++++++++++++++
> > 6 files changed, 1161 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts
> > create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts
> > create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dtsi
> > create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm.dts
> > create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi
> >
> > diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> > index 458bbc422a94..b45a45a565a1 100644
> > --- a/arch/arm64/boot/dts/mediatek/Makefile
> > +++ b/arch/arm64/boot/dts/mediatek/Makefile
> > @@ -6,5 +6,8 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb
> > dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
> > dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
> > dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
> > +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm.dtb
> > +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana.dtb
> > +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana-rev7.dtb
> > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-evb.dtb
> > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-evb.dtb
> > diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts
> > new file mode 100644
> > index 000000000000..a3616bc3d859
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts
> > @@ -0,0 +1,27 @@
> > +// SPDX-License-Identifier: GPL-2.0-only
> > +/*
> > + * Copyright 2019 MediaTek Inc.
> > + */
> > +
> > +/dts-v1/;
> > +#include "mt8173-elm-hana.dtsi"
> > +
> > +/ {
> > + model = "Mediatek Hana rev7 board";
> > + compatible = "google,hana-rev7", "mediatek,mt8173";
> > +};
> > +
> > +&cpu_thermal {
> > + trips {
> > + cpu_crit: cpu_crit@0 {
> > + temperature = <100000>;
> > + type = "critical";
> > + };
> > + };
> > +};
> > +
> > +&gpio_keys {
> > + /delete-node/tablet_mode;
> > + /delete-node/volume_down;
> > + /delete-node/volume_up;
> > +};
> > \ No newline at end of file
> > diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts
> > new file mode 100644
> > index 000000000000..8cbcc75192e3
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts
> > @@ -0,0 +1,16 @@
> > +// SPDX-License-Identifier: GPL-2.0-only
> > +/*
> > + * Copyright 2016 MediaTek Inc.
> > + */
> > +
> > +/dts-v1/;
> > +#include "mt8173-elm-hana.dtsi"
> > +
> > +/ {
> > + model = "Mediatek Hana rev0 board";
> > + compatible = "google,hana-rev6",
> > + "google,hana-rev5", "google,hana-rev4",
> > + "google,hana-rev3", "google,hana-rev2",
> > + "google,hana-rev1", "google,hana-rev0",
> > + "google,hana", "mediatek,mt8173";
> > +};
>
> I'm a bit confused about all this versions. Do you want to keep them for
> internal use, as I suppose only rev6 is available to the general public,
> correct? I'm fine with keeping the old revisions if that's of use for you,
> otherwise I'd prefer to delete them.
According to internal feedback system, at least rev3, rev6, rev7 are
in general public. I can delete rev0~rev2, since they are earlier
version device.
>
> Model name could be more verbose.
>
> > \ No newline at end of file
> > diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dtsi b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dtsi
> > new file mode 100644
> > index 000000000000..35e12b290947
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dtsi
> > @@ -0,0 +1,60 @@
> > +// SPDX-License-Identifier: GPL-2.0-only
> > +/*
> > + * Copyright 2016 MediaTek Inc.
> > + */
> > +
> > +#include "mt8173-elm.dtsi"
> > +
> > +&i2c0 {
> > + clock-frequency = <200000>;
> > +};
> > +
> > +&i2c3 {
> > + touchscreen2: touchscreen@34 {
> > + compatible = "melfas,mip4_ts";
> > + reg = <0x34>;
> > + interrupt-parent = <&pio>;
> > + interrupts = <88 IRQ_TYPE_LEVEL_LOW>;
> > + };
> > +
> > + touchscreen3: touchscreen@20 {
> > + compatible = "hid-over-i2c";
> > + reg = <0x20>;
> > + hid-descr-addr = <0x0020>;
> > + interrupt-parent = <&pio>;
> > + interrupts = <88 IRQ_TYPE_LEVEL_LOW>;
> > + };
>
> In v1 you mentioned:
> "Partners wants to increase touchpad and touchscreen source (they choose
> synaptics) for hana 300e, and synaptics uses hid-over-i2c driver."
>
> So the partner uses the same compatible (google,hana-rev6?) for both devices?
>
Confirmed with others, second source devices share same compatible.
> > +};
> > +
> > +&i2c4 {
> > + trackpad2: trackpad@2c {
> > + compatible = "hid-over-i2c";
> > + interrupt-parent = <&pio>;
> > + interrupts = <117 IRQ_TYPE_LEVEL_LOW>;
> > + reg = <0x2c>;
> > + hid-descr-addr = <0x0020>;
> > + wakeup-source;
> > + };
> > +};
> > +
> > +&mmc1 {
> > + wp-gpios = <&pio 42 GPIO_ACTIVE_HIGH>;
> > +};
> > +
> > +&pio {
> > + hdmi_mux_pins: hdmi_mux_pins {
> > + pins2 {
> > + pinmux = <MT8173_PIN_98_URTS1__FUNC_GPIO98>;
> > + bias-pull-up;
> > + output-high;
> > + };
> > + };
> > +
> > + mmc1_pins_default: mmc1default {
> > + pins_wp {
> > + pinmux = <MT8173_PIN_42_DSI_TE__FUNC_GPIO42>;
> > + input-enable;
> > + bias-pull-up;
> > + };
> > + };
> > +};
> > \ No newline at end of file
> > diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm.dts b/arch/arm64/boot/dts/mediatek/mt8173-elm.dts
> > new file mode 100644
> > index 000000000000..e5da2355760e
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/mediatek/mt8173-elm.dts
> > @@ -0,0 +1,15 @@
> > +// SPDX-License-Identifier: GPL-2.0-only
> > +/*
> > + * Copyright 2016 MediaTek Inc.
> > + */
> > +
> > +/dts-v1/;
> > +#include "mt8173-elm.dtsi"
> > +
> > +/ {
> > + model = "Mediatek Elm board";
> > + compatible = "google,elm-rev8", "google,elm-rev7", "google,elm-rev6",
> > + "google,elm-rev5", "google,elm-rev4", "google,elm-rev3",
> > + "google,elm-rev2", "google,elm-rev1",
> > + "google,elm", "mediatek,mt8173";
> > +};
> > \ No newline at end of file
> > diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi b/arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi
> > new file mode 100644
> > index 000000000000..2ac738bebe04
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi
> > @@ -0,0 +1,1040 @@
> > +// SPDX-License-Identifier: GPL-2.0-only
> > +/*
> > + * Copyright 2016 MediaTek Inc.
> > + */
> > +
> > +#include <dt-bindings/input/input.h>
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include "mt8173.dtsi"
> > +
> > +/ {
> > + aliases {
> > + serial0 = &uart0;
> > + serial1 = &uart1;
> > + serial2 = &uart2;
> > + serial3 = &uart3;
> > + };
> > +
> > + memory@40000000 {
> > + device_type = "memory";
> > + reg = <0 0x40000000 0 0x80000000>;
> > + };
> > +
> > + backlight_lcd: backlight_lcd {
> > + compatible = "pwm-backlight";
> > + pwms = <&pwm0 0 1000000>;
> > + brightness-levels = <
> > + 0 16 32 48 64 80 96 112
> > + 128 144 160 176 192 208 224 240
> > + 255
> > + >;
> > + default-brightness-level = <9>;
> > + power-supply = <&bl_fixed_reg>;
> > + enable-gpios = <&pio 95 GPIO_ACTIVE_HIGH>;
> > +
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&disp_pwm0_pins>;
> > + status = "okay";
> > + };
> > +
> > + bl_fixed_reg: fixedregulator@2 {
> > + compatible = "regulator-fixed";
> > + regulator-name = "bl_fixed";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + startup-delay-us = <1000>;
> > + enable-active-high;
> > + gpio = <&pio 32 GPIO_ACTIVE_HIGH>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&bl_fixed_pins>;
> > + };
> > +
> > + chosen {
> > + stdout-path = &uart0;
> > + };
> > +
> > + gpio_keys: gpio-keys {
> > + compatible = "gpio-keys";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&gpio_keys_pins>;
> > +
> > + lid {
> > + label = "Lid";
> > + gpios = <&pio 69 GPIO_ACTIVE_LOW>;
> > + linux,code = <0>; /* SW_LID */
> > + linux,input-type = <5>; /* EV_SW */
> > + gpio-key,wakeup;
> > + };
> > +
> > + power {
> > + label = "Power";
> > + gpios = <&pio 14 GPIO_ACTIVE_HIGH>;
> > + linux,code = <KEY_POWER>;
> > + debounce-interval = <30>;
> > + gpio-key,wakeup;
> > + };
> > +
> > + tablet_mode {
> > + label = "Tablet_mode";
> > + gpios = <&pio 121 GPIO_ACTIVE_HIGH>;
> > + linux,code = <1>; /* SW_TABLET_MODE */
>
> can't we use SW_TABLET_MODE fomr linux-event-codes.h?
>
Will fix this.
> > + linux,input-type = <5>; /* EV_SW */
>
> same here.
>
> > + gpio-key,wakeup;
> > + };
> > +
> > + volume_down {
> > + label = "Volume_down";
> > + gpios = <&pio 123 GPIO_ACTIVE_LOW>;
> > + linux,code = <KEY_VOLUMEDOWN>;
> > + };
> > +
> > + volume_up {
> > + label = "Volume_up";
> > + gpios = <&pio 124 GPIO_ACTIVE_LOW>;
> > + linux,code = <KEY_VOLUMEUP>;
> > + };
> > + };
> > +
> > + panel: panel {
> > + compatible = "lg,lp120up1";
> > + power-supply = <&panel_fixed_3v3>;
> > + ddc-i2c-bus = <&i2c0>;
> > + backlight = <&backlight_lcd>;
> > +
> > + port {
> > + panel_in: endpoint {
> > + remote-endpoint = <&ps8640_out>;
> > + };
> > + };
> > + };
> > +
> > + panel_fixed_3v3: regulator@1 {
> > + compatible = "regulator-fixed";
> > + regulator-name = "PANEL_3V3";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + enable-active-high;
> > + gpio = <&pio 41 GPIO_ACTIVE_HIGH>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&panel_fixed_pins>;
> > + };
> > +
> > + ps8640_fixed_1v2: regulator@2 {
> > + compatible = "regulator-fixed";
> > + regulator-name = "PS8640_1V2";
> > + regulator-min-microvolt = <1200000>;
> > + regulator-max-microvolt = <1200000>;
> > + regulator-enable-ramp-delay = <2000>;
> > + enable-active-high;
> > + regulator-boot-on;
> > + gpio = <&pio 30 GPIO_ACTIVE_HIGH>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&ps8640_fixed_pins>;
> > + };
> > +
> > + sdio_fixed_3v3: fixedregulator@0 {
> > + compatible = "regulator-fixed";
> > + regulator-name = "3V3";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + gpio = <&pio 85 GPIO_ACTIVE_HIGH>;
>
> we don't need to set the pincontroller mux here?
>
Will double check on schematic and add it.
> > + };
> > +
> > + sound: sound {
> > + compatible = "mediatek,mt8173-rt5650";
> > + mediatek,audio-codec = <&rt5650 &hdmi0>;
> > + mediatek,platform = <&afe>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&aud_i2s2>;
> > +
> > + mediatek,mclk = <1>;
> > + codec-capture {
> > + sound-dai = <&rt5650 1>;
> > + };
> > + };
> > +
> > + hdmicon: connector {
> > + compatible = "hdmi-connector";
> > + label = "hdmi";
> > + type = "a";
> > + ddc-i2c-bus = <&hdmiddc0>;
> > +
> > + port {
> > + hdmi_connector_in: endpoint {
> > + remote-endpoint = <&hdmi0_out>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&cec {
> > + status = "okay";
> > +};
> > +
> > +&cpu0 {
> > + proc-supply = <&mt6397_vpca15_reg>;
> > +};
> > +
> > +&cpu1 {
> > + proc-supply = <&mt6397_vpca15_reg>;
> > +};
> > +
> > +&cpu2 {
> > + proc-supply = <&da9211_vcpu_reg>;
> > + sram-supply = <&mt6397_vsramca7_reg>;
> > +};
> > +
> > +&cpu3 {
> > + proc-supply = <&da9211_vcpu_reg>;
> > + sram-supply = <&mt6397_vsramca7_reg>;
> > +};
> > +
> > +&cpu_thermal {
> > + sustainable-power = <4500>; /* milliwatts */
> > + trips {
> > + threshold: trip-point@0 {
> > + temperature = <60000>;
> > + };
> > +
> > + target: trip-point@1 {
> > + temperature = <65000>;
> > + };
> > + };
> > +};
> > +
> > +&dsi0 {
> > + status = "okay";
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port@1 {
> > + dsi0_out: endpoint {
> > + remote-endpoint = <&ps8640_in>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&dpi0 {
> > + status = "okay";
> > +};
> > +
> > +&hdmi0 {
> > + status = "okay";
> > + ports {
> > + port@1 {
> > + reg = <1>;
> > +
> > + hdmi0_out: endpoint {
> > + remote-endpoint = <&hdmi_connector_in>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&hdmi_phy {
> > + status = "okay";
> > + mediatek,ibias = <0xc>;
> > +};
> > +
> > +&i2c0 {
> > + status = "okay";
> > +
> > + rt5650: audio-codec@1a {
> > + compatible = "realtek,rt5650";
> > + reg = <0x1a>;
> > + avdd-supply = <&mt6397_vgp1_reg>;
> > + cpvdd-supply = <&mt6397_vcama_reg>;
>
> Hm, only defined for "realtek,rt5663", I suppose that's an inconsistency in the
> binding documentation. Can you please double check?
>
This one? https://github.com/torvalds/linux/blob/master/sound/soc/codecs/rt5645.c#L3582
> > + interrupt-parent = <&pio>;
> > + interrupts = <3 IRQ_TYPE_EDGE_BOTH>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&rt5650_irq>;
> > + #sound-dai-cells = <1>;
> > + realtek,dmic1-data-pin = <2>;
> > + realtek,jd-mode = <2>;
> > + };
> > +
> > + ps8640: edp-bridge@8 {
> > + compatible = "parade,ps8640";
> > + reg = <0x8>;
> > + powerdown-gpios = <&pio 127 GPIO_ACTIVE_LOW>;
> > + reset-gpios = <&pio 115 GPIO_ACTIVE_LOW>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&ps8640_pins>;
> > + vdd12-supply = <&ps8640_fixed_1v2>;
> > + vdd33-supply = <&mt6397_vgp2_reg>;
> > +
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port@0 {
> > + reg = <0>;
> > +
> > + ps8640_in: endpoint {
> > + remote-endpoint = <&dsi0_out>;
> > + };
> > + };
> > +
> > + port@1 {
> > + reg = <1>;
> > +
> > + ps8640_out: endpoint {
> > + remote-endpoint = <&panel_in>;
> > + };
> > + };
> > + };
> > + };
> > +};
> > +
> > +&i2c1 {
> > + clock-frequency = <1500000>;
> > + status = "okay";
> > +
> > + da9211: da9211@68 {
> > + compatible = "dlg,da9211";
> > + reg = <0x68>;
> > +
>
> no interrupts? binding description have this stated as required. what happens
> when the device raises an interrupt?
Will double check on schematic and add it.
>
> > + regulators {
> > + da9211_vcpu_reg: BUCKA {
> > + regulator-name = "VBUCKA";
> > + regulator-min-microvolt = < 700000>;
> > + regulator-max-microvolt = <1310000>;
> > + regulator-min-microamp = <2000000>;
> > + regulator-max-microamp = <4400000>;
> > + regulator-ramp-delay = <10000>;
> > + regulator-always-on;
> > + regulator-allowed-modes = <0 1>;
> > + };
> > +
> > + da9211_vgpu_reg: BUCKB {
> > + regulator-name = "VBUCKB";
> > + regulator-min-microvolt = < 700000>;
> > + regulator-max-microvolt = <1310000>;
> > + regulator-min-microamp = <2000000>;
> > + regulator-max-microamp = <3000000>;
> > + regulator-ramp-delay = <10000>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&i2c2 {
> > + status = "okay";
> > +
> > + tpm: tpm@20 {
> > + compatible = "infineon,slb9645tt";
> > + reg = <0x20>;
> > + powered-while-suspended;
> > + };
> > +};
> > +
> > +&i2c3 {
> > + clock-frequency = <400000>;
> > + status = "okay";
> > +
> > + touchscreen: touchscreen@10 {
> > + compatible = "elan,ekth3500";
> > + reg = <0x10>;
> > + interrupt-parent = <&pio>;
> > + interrupts = <88 IRQ_TYPE_LEVEL_LOW>;
> > + };
> > +};
> > +
> > +&i2c4 {
> > + clock-frequency = <400000>;
> > + status = "okay";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&trackpad_irq>;
>
> Why not move the pinctrl properties into the trackpad node?
>
As second source trackpad device and original device shares same
compatible string (rev id), we need to add 2nd trackpad node here.
According to previous log (since I don't have a second source trackpad
device to test), adding pinctrl in each trackpad node, there would be
error:
[ 0.643501] mediatek-mt8173-pinctrl 1000b000.pinctrl: pin URXD3
already requested by 7-0015; cannot claim for 7-002c
[ 0.643525] mediatek-mt8173-pinctrl 1000b000.pinctrl: pin-117
(7-002c) status -22
[ 0.643548] mediatek-mt8173-pinctrl 1000b000.pinctrl: could not
request pin 117 (URXD3) from group URXD3 on device 1000b000.pinctrl
[ 0.643568] i2c_hid 7-002c: Error applying setting, reverse things back
[ 0.643867] i2c 7-002c: Driver i2c_hid requests probe deferral
> > +
> > + trackpad: trackpad@15 {
> > + compatible = "elan,ekth3000";
> > + interrupt-parent = <&pio>;
> > + interrupts = <117 IRQ_TYPE_LEVEL_LOW>;
> > + reg = <0x15>;
> > + vcc-supply = <&mt6397_vgp6_reg>;
> > + wakeup-source;
> > + };
> > +};
> > +
> > +&mipi_tx0 {
> > + status = "okay";
> > +};
> > +
> > +&mmc0 {
> > + status = "okay";
> > + pinctrl-names = "default", "state_uhs";
> > + pinctrl-0 = <&mmc0_pins_default>;
> > + pinctrl-1 = <&mmc0_pins_uhs>;
> > + bus-width = <8>;
> > + max-frequency = <200000000>;
> > + cap-mmc-highspeed;
> > + mmc-hs200-1_8v;
> > + mmc-hs400-1_8v;
> > + cap-mmc-hw-reset;
> > + hs400-ds-delay = <0x14015>;
> > + mediatek,hs200-cmd-int-delay=<30>;
> > + mediatek,hs400-cmd-int-delay=<14>;
> > + mediatek,hs400-cmd-resp-sel-rising;
> > + vmmc-supply = <&mt6397_vemc_3v3_reg>;
> > + vqmmc-supply = <&mt6397_vio18_reg>;
> > + assigned-clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>;
> > + assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL_D2>;
> > + non-removable;
> > +};
> > +
> > +&mmc1 {
> > + status = "okay";
> > + pinctrl-names = "default", "state_uhs";
> > + pinctrl-0 = <&mmc1_pins_default>;
> > + pinctrl-1 = <&mmc1_pins_uhs>;
> > + bus-width = <4>;
> > + max-frequency = <200000000>;
> > + cap-sd-highspeed;
> > + sd-uhs-sdr50;
> > + sd-uhs-sdr104;
> > + cd-gpios = <&pio 1 GPIO_ACTIVE_HIGH>;
> > + vmmc-supply = <&mt6397_vmch_reg>;
> > + vqmmc-supply = <&mt6397_vmc_reg>;
> > +};
> > +
> > +&mmc3 {
> > + status = "okay";
> > + pinctrl-names = "default", "state_uhs";
> > + pinctrl-0 = <&mmc3_pins_default>;
> > + pinctrl-1 = <&mmc3_pins_uhs>;
> > + bus-width = <4>;
> > + max-frequency = <200000000>;
> > + cap-sd-highspeed;
> > + sd-uhs-sdr50;
> > + sd-uhs-sdr104;
> > + sdr104-clk-delay = <5>;
>
> Not an upstream property, please delete it.
>
> > + keep-power-in-suspend;
> > + enable-sdio-wakeup;
> > + cap-sdio-irq;
> > + vmmc-supply = <&sdio_fixed_3v3>;
> > + vqmmc-supply = <&mt6397_vgp3_reg>;
> > + non-removable;
> > + cap-power-off-card;
> > +
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + btmrvl: btmrvl@2 {
> > + compatible = "marvell,sd8897-bt";
> > + reg = <2>;
> > + interrupt-parent = <&pio>;
> > + interrupts = <119 IRQ_TYPE_LEVEL_LOW>;
> > + marvell,wakeup-pin = /bits/ 16 <0x0d>;
> > + marvell,wakeup-gap-ms = /bits/ 16 <0x64>;
> > + };
> > +
> > + mwifiex: mwifiex@1 {
> > + compatible = "marvell,sd8897";
> > + reg = <1>;
> > + interrupt-parent = <&pio>;
> > + interrupts = <38 IRQ_TYPE_LEVEL_LOW>;
> > + marvell,wakeup-pin = <3>;
> > + marvell,caldata_ed_mac = /bits/ 8 <
> > +0x01 0x00 0x07 0x00 0x14 0x00 0x01 0x00 0x00 0x00 0x12 0x00 0x02 0x00 0x01 0x00
> > +0x01 0x00 0x00 0x00 0x12 0x00 0x02 0x00 0x01 0x00
> > + >;
>
> Not an upstream property, please delete.
>
> > + };
> > +};
> > +
> > +&nor_flash {
> > + status = "okay";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&nor_gpio1_pins>;
> > + bus-width = <8>;
> > + max-frequency = <50000000>;
> > + non-removable;
> > + flash@0 {
> > + compatible = "jedec,spi-nor";
> > + reg = <0>;
> > + };
> > +};
> > +
> > +&pio {
> > + aud_i2s2: aud_i2s2 {
> > + pins1 {
> > + pinmux = <MT8173_PIN_128_I2S0_LRCK__FUNC_I2S1_WS>,
> > + <MT8173_PIN_129_I2S0_BCK__FUNC_I2S1_BCK>,
> > + <MT8173_PIN_130_I2S0_MCK__FUNC_I2S1_MCK>,
> > + <MT8173_PIN_131_I2S0_DATA0__FUNC_I2S1_DO_1>,
> > + <MT8173_PIN_12_EINT12__FUNC_I2S2_WS>,
> > + <MT8173_PIN_13_EINT13__FUNC_I2S2_BCK>,
> > + <MT8173_PIN_132_I2S0_DATA1__FUNC_I2S2_DI_2>;
> > + bias-pull-down;
> > + };
> > + };
> > +
> > + bl_fixed_pins: bl_fixed_pins {
> > + pins1 {
> > + pinmux = <MT8173_PIN_32_UTXD2__FUNC_GPIO32>;
> > + output-low;
> > + };
> > + };
> > +
> > + bt_wake_pins: bt_wake_pins {
> > + pins1 {
> > + pinmux = <MT8173_PIN_119_KPROW0__FUNC_GPIO119>;
> > + bias-pull-up;
> > + };
> > + };
> > +
> > + disp_pwm0_pins: disp_pwm0_pins {
> > + pins1 {
> > + pinmux = <MT8173_PIN_87_DISP_PWM0__FUNC_DISP_PWM0>;
> > + output-low;
> > + };
> > + };
> > +
> > + gpio_keys_pins: gpio_keys_pins {
> > + volume_pins {
> > + pinmux = <MT8173_PIN_123_KPCOL1__FUNC_GPIO123>,
> > + <MT8173_PIN_124_KPCOL2__FUNC_GPIO124>;
> > + bias-pull-up;
> > + };
> > +
> > + tablet_mode_pins {
> > + pinmux = <MT8173_PIN_121_KPROW2__FUNC_GPIO121>;
> > + bias-pull-up;
> > + };
> > + };
> > +
> > + hdmi_mux_pins: hdmi_mux_pins {
> > + pins1 {
> > + pinmux = <MT8173_PIN_36_DAISYNC__FUNC_GPIO36>;
> > + };
> > + };
> > +
> > + mmc0_pins_default: mmc0default {
> > + pins_cmd_dat {
> > + pinmux = <MT8173_PIN_57_MSDC0_DAT0__FUNC_MSDC0_DAT0>,
> > + <MT8173_PIN_58_MSDC0_DAT1__FUNC_MSDC0_DAT1>,
> > + <MT8173_PIN_59_MSDC0_DAT2__FUNC_MSDC0_DAT2>,
> > + <MT8173_PIN_60_MSDC0_DAT3__FUNC_MSDC0_DAT3>,
> > + <MT8173_PIN_61_MSDC0_DAT4__FUNC_MSDC0_DAT4>,
> > + <MT8173_PIN_62_MSDC0_DAT5__FUNC_MSDC0_DAT5>,
> > + <MT8173_PIN_63_MSDC0_DAT6__FUNC_MSDC0_DAT6>,
> > + <MT8173_PIN_64_MSDC0_DAT7__FUNC_MSDC0_DAT7>,
> > + <MT8173_PIN_66_MSDC0_CMD__FUNC_MSDC0_CMD>;
> > + bias-pull-up;
> > + };
> > +
> > + pins_clk {
> > + pinmux = <MT8173_PIN_65_MSDC0_CLK__FUNC_MSDC0_CLK>;
> > + bias-pull-down;
>
> identation.
>
> > + };
> > +
> > + pins_rst {
> > + pinmux = <MT8173_PIN_68_MSDC0_RST___FUNC_MSDC0_RSTB>;
> > + bias-pull-up;
> > + };
> > + };
> > +
> > + mmc1_pins_default: mmc1default {
> > + pins_cmd_dat {
> > + pinmux = <MT8173_PIN_73_MSDC1_DAT0__FUNC_MSDC1_DAT0>,
> > + <MT8173_PIN_74_MSDC1_DAT1__FUNC_MSDC1_DAT1>,
> > + <MT8173_PIN_75_MSDC1_DAT2__FUNC_MSDC1_DAT2>,
> > + <MT8173_PIN_76_MSDC1_DAT3__FUNC_MSDC1_DAT3>,
> > + <MT8173_PIN_78_MSDC1_CMD__FUNC_MSDC1_CMD>;
> > + input-enable;
> > + drive-strength = <MTK_DRIVE_4mA>;
> > + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
> > + };
> > +
> > + pins_clk {
> > + pinmux = <MT8173_PIN_77_MSDC1_CLK__FUNC_MSDC1_CLK>;
> > + bias-pull-down;
> > + drive-strength = <MTK_DRIVE_4mA>;
> > + };
> > +
> > + pins_insert {
> > + pinmux = <MT8173_PIN_1_EINT1__FUNC_GPIO1>;
> > + bias-pull-up;
> > + };
> > + };
> > +
> > + mmc3_pins_default: mmc3default {
> > + pins_dat {
> > + pinmux = <MT8173_PIN_22_MSDC3_DAT0__FUNC_MSDC3_DAT0>,
> > + <MT8173_PIN_23_MSDC3_DAT1__FUNC_MSDC3_DAT1>,
> > + <MT8173_PIN_24_MSDC3_DAT2__FUNC_MSDC3_DAT2>,
> > + <MT8173_PIN_25_MSDC3_DAT3__FUNC_MSDC3_DAT3>;
> > + input-enable;
> > + drive-strength = <MTK_DRIVE_8mA>;
> > + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
> > + };
> > +
> > + pins_cmd {
> > + pinmux = <MT8173_PIN_27_MSDC3_CMD__FUNC_MSDC3_CMD>;
> > + input-enable;
> > + drive-strength = <MTK_DRIVE_8mA>;
> > + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
> > + };
> > +
> > + pins_clk {
> > + pinmux = <MT8173_PIN_26_MSDC3_CLK__FUNC_MSDC3_CLK>;
> > + bias-pull-down;
> > + drive-strength = <MTK_DRIVE_8mA>;
> > + };
> > +
> > + pins_pdn {
> > + pinmux = <MT8173_PIN_85_AUD_DAT_MOSI__FUNC_GPIO85>;
> > + output-low;
> > + };
> > + };
> > +
> > + mmc0_pins_uhs: mmc0 {
> > + pins_cmd_dat {
> > + pinmux = <MT8173_PIN_57_MSDC0_DAT0__FUNC_MSDC0_DAT0>,
> > + <MT8173_PIN_58_MSDC0_DAT1__FUNC_MSDC0_DAT1>,
> > + <MT8173_PIN_59_MSDC0_DAT2__FUNC_MSDC0_DAT2>,
> > + <MT8173_PIN_60_MSDC0_DAT3__FUNC_MSDC0_DAT3>,
> > + <MT8173_PIN_61_MSDC0_DAT4__FUNC_MSDC0_DAT4>,
> > + <MT8173_PIN_62_MSDC0_DAT5__FUNC_MSDC0_DAT5>,
> > + <MT8173_PIN_63_MSDC0_DAT6__FUNC_MSDC0_DAT6>,
> > + <MT8173_PIN_64_MSDC0_DAT7__FUNC_MSDC0_DAT7>,
> > + <MT8173_PIN_66_MSDC0_CMD__FUNC_MSDC0_CMD>;
> > + input-enable;
> > + drive-strength = <MTK_DRIVE_6mA>;
> > + bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
> > + };
> > +
> > + pins_clk {
> > + pinmux = <MT8173_PIN_65_MSDC0_CLK__FUNC_MSDC0_CLK>;
> > + drive-strength = <MTK_DRIVE_6mA>;
> > + bias-pull-down = <MTK_PUPD_SET_R1R0_01>;
> > + };
> > +
> > + pins_ds {
> > + pinmux = <MT8173_PIN_67_MSDC0_DSL__FUNC_MSDC0_DSL>;
> > + drive-strength = <MTK_DRIVE_10mA>;
> > + bias-pull-down = <MTK_PUPD_SET_R1R0_01>;
> > + };
> > +
> > + pins_rst {
> > + pinmux = <MT8173_PIN_68_MSDC0_RST___FUNC_MSDC0_RSTB>;
> > + bias-pull-up;
> > + };
> > + };
> > +
> > + mmc1_pins_uhs: mmc1 {
> > + pins_cmd_dat {
> > + pinmux = <MT8173_PIN_73_MSDC1_DAT0__FUNC_MSDC1_DAT0>,
> > + <MT8173_PIN_74_MSDC1_DAT1__FUNC_MSDC1_DAT1>,
> > + <MT8173_PIN_75_MSDC1_DAT2__FUNC_MSDC1_DAT2>,
> > + <MT8173_PIN_76_MSDC1_DAT3__FUNC_MSDC1_DAT3>,
> > + <MT8173_PIN_78_MSDC1_CMD__FUNC_MSDC1_CMD>;
> > + input-enable;
> > + drive-strength = <MTK_DRIVE_6mA>;
> > + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
> > + };
> > +
> > + pins_clk {
> > + pinmux = <MT8173_PIN_77_MSDC1_CLK__FUNC_MSDC1_CLK>;
> > + drive-strength = <MTK_DRIVE_8mA>;
> > + bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
> > + };
> > + };
> > +
> > + mmc3_pins_uhs: mmc3 {
> > + pins_dat {
> > + pinmux = <MT8173_PIN_22_MSDC3_DAT0__FUNC_MSDC3_DAT0>,
> > + <MT8173_PIN_23_MSDC3_DAT1__FUNC_MSDC3_DAT1>,
> > + <MT8173_PIN_24_MSDC3_DAT2__FUNC_MSDC3_DAT2>,
> > + <MT8173_PIN_25_MSDC3_DAT3__FUNC_MSDC3_DAT3>;
> > + input-enable;
> > + drive-strength = <MTK_DRIVE_8mA>;
> > + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
> > + };
> > +
> > + pins_cmd {
> > + pinmux = <MT8173_PIN_27_MSDC3_CMD__FUNC_MSDC3_CMD>;
> > + input-enable;
> > + drive-strength = <MTK_DRIVE_8mA>;
> > + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
> > + };
> > +
> > + pins_clk {
> > + pinmux = <MT8173_PIN_26_MSDC3_CLK__FUNC_MSDC3_CLK>;
> > + drive-strength = <MTK_DRIVE_8mA>;
> > + bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
> > + };
> > + };
> > +
> > + nor_gpio1_pins: nor {
> > + pins1 {
> > + pinmux = <MT8173_PIN_6_EINT6__FUNC_SFCS0>,
> > + <MT8173_PIN_7_EINT7__FUNC_SFHOLD>,
> > + <MT8173_PIN_8_EINT8__FUNC_SFIN>;
> > + input-enable;
> > + drive-strength = <MTK_DRIVE_4mA>;
> > + bias-pull-up;
> > + };
> > +
> > + pins2 {
> > + pinmux = <MT8173_PIN_5_EINT5__FUNC_SFOUT>;
> > + drive-strength = <MTK_DRIVE_4mA>;
> > + bias-pull-up;
> > + };
> > +
> > + pins_clk {
> > + pinmux = <MT8173_PIN_9_EINT9__FUNC_SFCK>;
> > + input-enable;
> > + drive-strength = <MTK_DRIVE_4mA>;
> > + bias-pull-up;
> > + };
> > + };
> > +
> > + panel_fixed_pins: panel_fixed_pins {
> > + pins1 {
> > + pinmux = <MT8173_PIN_41_CMMCLK__FUNC_GPIO41>;
> > + };
> > + };
> > +
> > + ps8640_pins: ps8640_pins {
> > + pins1 {
> > + pinmux = <MT8173_PIN_92_PCM_CLK__FUNC_GPIO92>,
> > + <MT8173_PIN_115_URTS0__FUNC_GPIO115>,
> > + <MT8173_PIN_127_LCM_RST__FUNC_GPIO127>;
> > + };
> > + };
> > +
> > + ps8640_fixed_pins: ps8640_fixed_pins {
> > + pins1 {
> > + pinmux = <MT8173_PIN_30_URTS2__FUNC_GPIO30>;
> > + };
> > + };
> > +
> > + rt5650_irq: rt5650_irq {
> > + pins1 {
> > + pinmux = <MT8173_PIN_3_EINT3__FUNC_GPIO3>;
> > + bias-pull-down;
> > + };
> > + };
> > +
> > + spi_pins_a: spi1 {
> > + pins1 {
> > + pinmux = <MT8173_PIN_0_EINT0__FUNC_GPIO0>;
> > + bias-pull-up;
> > + };
> > +
> > + pins_spi {
> > + pinmux = <MT8173_PIN_102_MSDC2_DAT2__FUNC_SPI_CK_1_>,
> > + <MT8173_PIN_103_MSDC2_DAT3__FUNC_SPI_MI_1_>,
> > + <MT8173_PIN_104_MSDC2_CLK__FUNC_SPI_MO_1_>,
> > + <MT8173_PIN_105_MSDC2_CMD__FUNC_SPI_CS_1_>;
> > + bias-disable;
> > + };
> > + };
> > +
> > + trackpad_irq: trackpad_irq {
> > + pins1 {
> > + pinmux = <MT8173_PIN_117_URXD3__FUNC_GPIO117>;
> > + input-enable;
> > + bias-pull-up;
> > + };
> > + };
> > +
> > + usb_pins: usb@0 {
> > + pins1 {
> > + pinmux = <MT8173_PIN_101_MSDC2_DAT1__FUNC_GPIO101>;
> > + output-high;
> > + bias-disable;
> > + };
> > + };
> > +
> > + wifi_wake_pins: wifi_wake_pins {
> > + pins1 {
> > + pinmux = <MT8173_PIN_38_CONN_RST__FUNC_GPIO38>;
> > + bias-pull-up;
> > + };
> > + };
> > +};
> > +
> > +&pwm0 {
> > + status = "okay";
> > +};
> > +
> > +&pwrap {
> > + pmic: mt6397 {
> > + compatible = "mediatek,mt6397";
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + interrupt-parent = <&pio>;
> > + interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > +
> > + mt6397rtc: mt6397rtc {
>
> AFAIK this should be
> rtc: mt6397rtc {
>
> Please fix that for all subnodes.
>
Will fix in next version
> > + compatible = "mediatek,mt6397-rtc";
> > + };
> > +
> > + syscfg_pctl_pmic: syscfg_pctl_pmic@c000 {
> > + compatible = "mediatek,mt6397-pctl-pmic-syscfg",
> > + "syscon";
> > + reg = <0 0x0000c000 0 0x0108>;
>
> not an upstream compatible, please delete the node.
>
> > + };
> > +
> > + pio6397: pinctrl@c000 {
> > + compatible = "mediatek,mt6397-pinctrl";
> > + pins-are-numbered;
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > + };
> > +
> > + mt6397clock: mt6397clock {
> > + compatible = "mediatek,mt6397-clk";
> > + #clock-cells = <1>;
> > + };
> > +
> > + mt6397regulator: mt6397regulator {
> > + compatible = "mediatek,mt6397-regulator";
> > +
> > + mt6397_vpca15_reg: buck_vpca15 {
> > + regulator-compatible = "buck_vpca15";
> > + regulator-name = "vpca15";
> > + regulator-min-microvolt = < 700000>;
> > + regulator-max-microvolt = <1350000>;
> > + regulator-ramp-delay = <12500>;
> > + regulator-always-on;
> > + regulator-allowed-modes = <0 1>;
> > + };
> > +
> > + mt6397_vpca7_reg: buck_vpca7 {
> > + regulator-compatible = "buck_vpca7";
> > + regulator-name = "vpca7";
> > + regulator-min-microvolt = < 700000>;
> > + regulator-max-microvolt = <1350000>;
> > + regulator-ramp-delay = <12500>;
> > + regulator-enable-ramp-delay = <115>;
> > + regulator-always-on;
> > + };
> > +
> > + mt6397_vsramca15_reg: buck_vsramca15 {
> > + regulator-compatible = "buck_vsramca15";
> > + regulator-name = "vsramca15";
> > + regulator-min-microvolt = < 700000>;
> > + regulator-max-microvolt = <1350000>;
> > + regulator-ramp-delay = <12500>;
> > + regulator-always-on;
> > + };
> > +
> > + mt6397_vsramca7_reg: buck_vsramca7 {
> > + regulator-compatible = "buck_vsramca7";
> > + regulator-name = "vsramca7";
> > + regulator-min-microvolt = < 700000>;
> > + regulator-max-microvolt = <1350000>;
> > + regulator-ramp-delay = <12500>;
> > + regulator-always-on;
> > + };
> > +
> > + mt6397_vcore_reg: buck_vcore {
> > + regulator-compatible = "buck_vcore";
> > + regulator-name = "vcore";
> > + regulator-min-microvolt = < 700000>;
> > + regulator-max-microvolt = <1350000>;
> > + regulator-ramp-delay = <12500>;
> > + regulator-always-on;
> > + };
> > +
> > + mt6397_vgpu_reg: buck_vgpu {
> > + regulator-compatible = "buck_vgpu";
> > + regulator-name = "vgpu";
> > + regulator-min-microvolt = < 700000>;
> > + regulator-max-microvolt = <1350000>;
> > + regulator-ramp-delay = <12500>;
> > + regulator-enable-ramp-delay = <115>;
> > + };
> > +
> > + mt6397_vdrm_reg: buck_vdrm {
> > + regulator-compatible = "buck_vdrm";
> > + regulator-name = "vdrm";
> > + regulator-min-microvolt = <1200000>;
> > + regulator-max-microvolt = <1400000>;
> > + regulator-ramp-delay = <12500>;
> > + regulator-always-on;
> > + };
> > +
> > + mt6397_vio18_reg: buck_vio18 {
> > + regulator-compatible = "buck_vio18";
> > + regulator-name = "vio18";
> > + regulator-min-microvolt = <1620000>;
> > + regulator-max-microvolt = <1980000>;
> > + regulator-ramp-delay = <12500>;
> > + regulator-always-on;
> > + };
> > +
> > + mt6397_vtcxo_reg: ldo_vtcxo {
> > + regulator-compatible = "ldo_vtcxo";
> > + regulator-name = "vtcxo";
> > + regulator-always-on;
> > + };
> > +
> > + mt6397_va28_reg: ldo_va28 {
> > + regulator-compatible = "ldo_va28";
> > + regulator-name = "va28";
> > + };
> > +
> > + mt6397_vcama_reg: ldo_vcama {
> > + regulator-compatible = "ldo_vcama";
> > + regulator-name = "vcama";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-enable-ramp-delay = <218>;
> > + };
> > +
> > + mt6397_vio28_reg: ldo_vio28 {
> > + regulator-compatible = "ldo_vio28";
> > + regulator-name = "vio28";
> > + regulator-always-on;
> > + };
> > +
> > + mt6397_vusb_reg: ldo_vusb {
> > + regulator-compatible = "ldo_vusb";
> > + regulator-name = "vusb";
> > + };
> > +
> > + mt6397_vmc_reg: ldo_vmc {
> > + regulator-compatible = "ldo_vmc";
> > + regulator-name = "vmc";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-enable-ramp-delay = <218>;
> > + };
> > +
> > + mt6397_vmch_reg: ldo_vmch {
> > + regulator-compatible = "ldo_vmch";
> > + regulator-name = "vmch";
> > + regulator-min-microvolt = <3000000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-enable-ramp-delay = <218>;
> > + };
> > +
> > + mt6397_vemc_3v3_reg: ldo_vemc3v3 {
> > + regulator-compatible = "ldo_vemc3v3";
> > + regulator-name = "vemc_3v3";
> > + regulator-min-microvolt = <3000000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-enable-ramp-delay = <218>;
> > + };
> > +
> > + mt6397_vgp1_reg: ldo_vgp1 {
> > + regulator-compatible = "ldo_vgp1";
> > + regulator-name = "vcamd";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-enable-ramp-delay = <240>;
> > + };
> > +
> > + mt6397_vgp2_reg: ldo_vgp2 {
> > + regulator-compatible = "ldo_vgp2";
> > + regulator-name = "vcamio";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-enable-ramp-delay = <218>;
> > + };
> > +
> > + mt6397_vgp3_reg: ldo_vgp3 {
> > + regulator-compatible = "ldo_vgp3";
> > + regulator-name = "vcamaf";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-enable-ramp-delay = <218>;
> > + };
> > +
> > + mt6397_vgp4_reg: ldo_vgp4 {
> > + regulator-compatible = "ldo_vgp4";
> > + regulator-name = "vgp4";
> > + regulator-min-microvolt = <1200000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-enable-ramp-delay = <218>;
> > + };
> > +
> > + mt6397_vgp5_reg: ldo_vgp5 {
> > + regulator-compatible = "ldo_vgp5";
> > + regulator-name = "vgp5";
> > + regulator-min-microvolt = <1200000>;
> > + regulator-max-microvolt = <3000000>;
> > + regulator-enable-ramp-delay = <218>;
> > + };
> > +
> > + mt6397_vgp6_reg: ldo_vgp6 {
> > + regulator-compatible = "ldo_vgp6";
> > + regulator-name = "vgp6";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-enable-ramp-delay = <218>;
> > + regulator-always-on;
> > + };
> > +
> > + mt6397_vibr_reg: ldo_vibr {
> > + regulator-compatible = "ldo_vibr";
> > + regulator-name = "vibr";
> > + regulator-min-microvolt = <1300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-enable-ramp-delay = <218>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&spi {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&spi_pins_a>;
> > + mediatek,pad-select = <1>;
> > + status = "okay";
> > + /* clients */
> > + cros_ec: ec@0 {
> > + compatible = "google,cros-ec-spi";
> > + reg = <0x0>;
> > + spi-max-frequency = <12000000>;
> > + interrupt-parent = <&pio>;
> > + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> > + google,cros-ec-spi-msg-delay = <500>;
> > +
> > + i2c_tunnel: i2c-tunnel@0 {
> > + compatible = "google,cros-ec-i2c-tunnel";
> > + google,remote-bus = <0>;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + battery: sbs-battery@b {
> > + compatible = "sbs,sbs-battery";
> > + reg = <0xb>;
> > + sbs,i2c-retry-count = <2>;
> > + sbs,poll-retry-count = <1>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&thermal {
> > + bank0-supply = <&mt6397_vpca15_reg>;
> > + bank1-supply = <&da9211_vcpu_reg>;
> > +};
> > +
> > +&uart0 {
> > + status = "okay";
> > +};
> > +
> > +&ssusb {
> > + dr_mode = "host";
> > + wakeup-source;
> > + vusb33-supply = <&mt6397_vusb_reg>;
> > + status = "okay";
> > +};
> > +
> > +&usb_host {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&usb_pins>;
> > + vusb33-supply = <&mt6397_vusb_reg>;
> > + status = "okay";
> > +};
> > +
> > +#include "../../../../arm/boot/dts/cros-ec-keyboard.dtsi"
> Why don't we use
> #include <arm/cros-ec-keyboard.dtsi> ?
>
Will fix in next version
> > \ No newline at end of file
> >
>
> As Yingjoe already mentioned, please add a newline :)
>
> Regards,
> Matthias
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH v2 2/2] arm64: dts: mediatek: add mt8173 elm and hana board
2020-01-13 9:29 ` Enric Balletbo i Serra
@ 2020-01-13 18:18 ` Matthias Kaehlcke
0 siblings, 0 replies; 14+ messages in thread
From: Matthias Kaehlcke @ 2020-01-13 18:18 UTC (permalink / raw)
To: Enric Balletbo i Serra
Cc: Mark Rutland, devicetree, Nicolas Boichat, linux-kernel,
Daniel Kurtz, Doug Anderson, Rob Herring, linux-mediatek,
Hsin-Yi Wang, Matthias Brugger, linux-arm-kernel
Hi,
On Mon, Jan 13, 2020 at 10:29:51AM +0100, Enric Balletbo i Serra wrote:
> Hi Hsin-Yi,
>
> Apart from the maintainer comments, a few more comments ...
>
> cc'ing Matthias and Doug who I know played a bit with the pwm-backlight for the
> uprev of the veyron devices, and you might be interested in his feedback in general.
>
> On 10/1/20 8:37, Hsin-Yi Wang wrote:
> > Elm is Acer Chromebook R13. Hana is Lenovo Chromebook. Both uses mt8173
> > SoC.
> >
> > Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
> > ---
> > Changes in v2:
> > - remove downstream nodes and unused nodes
> > - use GPIO_ACTIVE_LOW for ps8640 gpios
> > - move trackpad to hana
> > ---
> > arch/arm64/boot/dts/mediatek/Makefile | 3 +
> > .../dts/mediatek/mt8173-elm-hana-rev7.dts | 27 +
> > .../boot/dts/mediatek/mt8173-elm-hana.dts | 16 +
> > .../boot/dts/mediatek/mt8173-elm-hana.dtsi | 60 +
> > arch/arm64/boot/dts/mediatek/mt8173-elm.dts | 15 +
> > arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi | 1040 +++++++++++++++++
> > 6 files changed, 1161 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts
> > create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts
> > create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dtsi
> > create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm.dts
> > create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi
<snip>
> > diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi b/arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi
> > new file mode 100644
> > index 000000000000..2ac738bebe04
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi
> > @@ -0,0 +1,1040 @@
> > +// SPDX-License-Identifier: GPL-2.0-only
> > +/*
> > + * Copyright 2016 MediaTek Inc.
> > + */
> > +
> > +#include <dt-bindings/input/input.h>
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include "mt8173.dtsi"
> > +
> > +/ {
> > + aliases {
> > + serial0 = &uart0;
> > + serial1 = &uart1;
> > + serial2 = &uart2;
> > + serial3 = &uart3;
> > + };
>
> I think this should be in mt8173.dtsi?
>
> > +
> > + memory@40000000 {
> > + device_type = "memory";
> > + reg = <0 0x40000000 0 0x80000000>;
> > + };
> > +
> > + backlight_lcd: backlight_lcd {
>
> nit: Not sure if you need to change or not, but this node is usually called
> backlight: backlight without the _lcd. Note that this imply a userspace change
> but /sys/class/backlight/backlight is more aligned with other boards (I guess)
> when you have only one backlight. See for example:
>
> git grep backlight arch/arm64/boot/*
>
> > + compatible = "pwm-backlight";
> > + pwms = <&pwm0 0 1000000>;
> > + brightness-levels = <
> > + 0 16 32 48 64 80 96 112
> > + 128 144 160 176 192 208 224 240
> > + 255
> > + >;
> > + default-brightness-level = <9>;
>
> The reason you see the display too dark is because userspace sets and remembers
> the default value you have using the above configuration which is only 16
> levels. So after removing the two above properties you should set a new
> brightness from userspace.
>
> AFAIK 16 levels is not enough to have fancy backlight effects on Chrome OS
> userspace, at least is not enough for Rockchip devices so I suppose is the same
> for Mediatek.
>
> You have to options here.
>
> A) Remove brightness-levels and default-brightness-level. This will end with a
> non-linear brightness curve for the backlight up to 4095 levels.
>
> # cat max_brightness
> 4095
>
> B) Use the num-interpolated-steps and default-brightness-level properties. This
> will end with a linear curve brightness. Similar to what is done for veyron
> devices but in this case with more levels because the PWM to control the
> backlight is 16-bits instead of 8-bits for veyron devices.
>
> *
> https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/arch/arm/boot/dts/rk3288-veyron-edp.dtsi#n42
>
> My guess is that you're interested on option B here to be coherent with other
> Chromebooks.
You could evaluate either way. One of the reasons to chose the interpolated-steps
for veyron was that some veyron panels require a minimum backlight level to
work properly. This can be easily configured with the linear curve, but
currently not with the non-linear one. Another reason was to keep the backlight
curve of a released device unaltered, though I think that's not strictly
required as long as the behavior with the non-linear curve is close/good enough.
Chrome OS user space supports both types of curves, for a new device I would
probably start with a non-linear curve, and only change that if the resulting
behavior doesn't meet expectations for some reason.
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH v2 2/2] arm64: dts: mediatek: add mt8173 elm and hana board
2020-01-13 18:01 ` Hsin-Yi Wang
@ 2020-01-14 15:10 ` Matthias Brugger
2020-01-14 15:33 ` Hsin-Yi Wang
2020-01-15 8:53 ` Hsin-Yi Wang
0 siblings, 2 replies; 14+ messages in thread
From: Matthias Brugger @ 2020-01-14 15:10 UTC (permalink / raw)
To: Hsin-Yi Wang
Cc: Mark Rutland, Devicetree List, Nicolas Boichat, lkml,
Daniel Kurtz, Rob Herring, linux-mediatek,
Enric Balletbo i Serra,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE
On 13/01/2020 19:01, Hsin-Yi Wang wrote:
> On Fri, Jan 10, 2020 at 9:42 PM Matthias Brugger <matthias.bgg@gmail.com> wrote:
>>
>>
> Thanks, I will address the comments and send next version
>>
>> On 10/01/2020 08:37, Hsin-Yi Wang wrote:
>>> Elm is Acer Chromebook R13. Hana is Lenovo Chromebook. Both uses mt8173
>>> SoC.
>>>
>>> Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
>>> ---
>>> Changes in v2:
>>> - remove downstream nodes and unused nodes
>>> - use GPIO_ACTIVE_LOW for ps8640 gpios
>>> - move trackpad to hana
>>> ---
>>> arch/arm64/boot/dts/mediatek/Makefile | 3 +
>>> .../dts/mediatek/mt8173-elm-hana-rev7.dts | 27 +
>>> .../boot/dts/mediatek/mt8173-elm-hana.dts | 16 +
>>> .../boot/dts/mediatek/mt8173-elm-hana.dtsi | 60 +
>>> arch/arm64/boot/dts/mediatek/mt8173-elm.dts | 15 +
>>> arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi | 1040 +++++++++++++++++
>>> 6 files changed, 1161 insertions(+)
>>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts
>>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts
>>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dtsi
>>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm.dts
>>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi
>>>
>>> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
>>> index 458bbc422a94..b45a45a565a1 100644
>>> --- a/arch/arm64/boot/dts/mediatek/Makefile
>>> +++ b/arch/arm64/boot/dts/mediatek/Makefile
>>> @@ -6,5 +6,8 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb
>>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
>>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
>>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
>>> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm.dtb
>>> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana.dtb
>>> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana-rev7.dtb
>>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-evb.dtb
>>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-evb.dtb
>>> diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts
>>> new file mode 100644
>>> index 000000000000..a3616bc3d859
>>> --- /dev/null
>>> +++ b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts
>>> @@ -0,0 +1,27 @@
>>> +// SPDX-License-Identifier: GPL-2.0-only
>>> +/*
>>> + * Copyright 2019 MediaTek Inc.
>>> + */
>>> +
>>> +/dts-v1/;
>>> +#include "mt8173-elm-hana.dtsi"
>>> +
>>> +/ {
>>> + model = "Mediatek Hana rev7 board";
>>> + compatible = "google,hana-rev7", "mediatek,mt8173";
>>> +};
>>> +
>>> +&cpu_thermal {
>>> + trips {
>>> + cpu_crit: cpu_crit@0 {
>>> + temperature = <100000>;
>>> + type = "critical";
>>> + };
>>> + };
>>> +};
>>> +
>>> +&gpio_keys {
>>> + /delete-node/tablet_mode;
>>> + /delete-node/volume_down;
>>> + /delete-node/volume_up;
>>> +};
>>> \ No newline at end of file
>>> diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts
>>> new file mode 100644
>>> index 000000000000..8cbcc75192e3
>>> --- /dev/null
>>> +++ b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts
>>> @@ -0,0 +1,16 @@
>>> +// SPDX-License-Identifier: GPL-2.0-only
>>> +/*
>>> + * Copyright 2016 MediaTek Inc.
>>> + */
>>> +
>>> +/dts-v1/;
>>> +#include "mt8173-elm-hana.dtsi"
>>> +
>>> +/ {
>>> + model = "Mediatek Hana rev0 board";
If we can't make this more verbose, at least delete rev0, that's confusing.
Should the name not be "Google Hana"?
>>> + compatible = "google,hana-rev6",
>>> + "google,hana-rev5", "google,hana-rev4",
>>> + "google,hana-rev3", "google,hana-rev2",
>>> + "google,hana-rev1", "google,hana-rev0",
>>> + "google,hana", "mediatek,mt8173";
>>> +};
>>
>> I'm a bit confused about all this versions. Do you want to keep them for
>> internal use, as I suppose only rev6 is available to the general public,
>> correct? I'm fine with keeping the old revisions if that's of use for you,
>> otherwise I'd prefer to delete them.
> According to internal feedback system, at least rev3, rev6, rev7 are
> in general public. I can delete rev0~rev2, since they are earlier
> version device.
If you don't plan to use the rev0 to rev2 in-house, then we can delete them.
>>
>> Model name could be more verbose.
>>
>>> \ No newline at end of file
>>> diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dtsi b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dtsi
>>> new file mode 100644
>>> index 000000000000..35e12b290947
>>> --- /dev/null
>>> +++ b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dtsi
>>> @@ -0,0 +1,60 @@
>>> +// SPDX-License-Identifier: GPL-2.0-only
>>> +/*
>>> + * Copyright 2016 MediaTek Inc.
>>> + */
>>> +
>>> +#include "mt8173-elm.dtsi"
>>> +
>>> +&i2c0 {
>>> + clock-frequency = <200000>;
>>> +};
>>> +
>>> +&i2c3 {
>>> + touchscreen2: touchscreen@34 {
>>> + compatible = "melfas,mip4_ts";
>>> + reg = <0x34>;
>>> + interrupt-parent = <&pio>;
>>> + interrupts = <88 IRQ_TYPE_LEVEL_LOW>;
>>> + };
>>> +
>>> + touchscreen3: touchscreen@20 {
>>> + compatible = "hid-over-i2c";
>>> + reg = <0x20>;
>>> + hid-descr-addr = <0x0020>;
>>> + interrupt-parent = <&pio>;
>>> + interrupts = <88 IRQ_TYPE_LEVEL_LOW>;
>>> + };
>>
>> In v1 you mentioned:
>> "Partners wants to increase touchpad and touchscreen source (they choose
>> synaptics) for hana 300e, and synaptics uses hid-over-i2c driver."
>>
>> So the partner uses the same compatible (google,hana-rev6?) for both devices?
>>
> Confirmed with others, second source devices share same compatible.
We should create independent dts for the different boards. Like it is done for
gru-scarlett. Doesn't the FW provide the sku number in the compatible string?
>>> +};
>>> +
>>> +&i2c4 {
>>> + trackpad2: trackpad@2c {
>>> + compatible = "hid-over-i2c";
>>> + interrupt-parent = <&pio>;
>>> + interrupts = <117 IRQ_TYPE_LEVEL_LOW>;
>>> + reg = <0x2c>;
>>> + hid-descr-addr = <0x0020>;
>>> + wakeup-source;
>>> + };
>>> +};
>>> +
>>> +&mmc1 {
>>> + wp-gpios = <&pio 42 GPIO_ACTIVE_HIGH>;
>>> +};
>>> +
>>> +&pio {
>>> + hdmi_mux_pins: hdmi_mux_pins {
>>> + pins2 {
>>> + pinmux = <MT8173_PIN_98_URTS1__FUNC_GPIO98>;
>>> + bias-pull-up;
>>> + output-high;
>>> + };
>>> + };
>>> +
>>> + mmc1_pins_default: mmc1default {
>>> + pins_wp {
>>> + pinmux = <MT8173_PIN_42_DSI_TE__FUNC_GPIO42>;
>>> + input-enable;
>>> + bias-pull-up;
>>> + };
>>> + };
>>> +};
>>> \ No newline at end of file
>>> diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm.dts b/arch/arm64/boot/dts/mediatek/mt8173-elm.dts
>>> new file mode 100644
>>> index 000000000000..e5da2355760e
>>> --- /dev/null
>>> +++ b/arch/arm64/boot/dts/mediatek/mt8173-elm.dts
>>> @@ -0,0 +1,15 @@
>>> +// SPDX-License-Identifier: GPL-2.0-only
>>> +/*
>>> + * Copyright 2016 MediaTek Inc.
>>> + */
>>> +
>>> +/dts-v1/;
>>> +#include "mt8173-elm.dtsi"
>>> +
>>> +/ {
>>> + model = "Mediatek Elm board";
>>> + compatible = "google,elm-rev8", "google,elm-rev7", "google,elm-rev6",
>>> + "google,elm-rev5", "google,elm-rev4", "google,elm-rev3",
>>> + "google,elm-rev2", "google,elm-rev1",
>>> + "google,elm", "mediatek,mt8173";
>>> +};
>>> \ No newline at end of file
>>> diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi b/arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi
>>> new file mode 100644
>>> index 000000000000..2ac738bebe04
>>> --- /dev/null
>>> +++ b/arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi
>>> @@ -0,0 +1,1040 @@
>>> +// SPDX-License-Identifier: GPL-2.0-only
>>> +/*
>>> + * Copyright 2016 MediaTek Inc.
>>> + */
>>> +
>>> +#include <dt-bindings/input/input.h>
>>> +#include <dt-bindings/gpio/gpio.h>
>>> +#include "mt8173.dtsi"
>>> +
>>> +/ {
>>> + aliases {
>>> + serial0 = &uart0;
>>> + serial1 = &uart1;
>>> + serial2 = &uart2;
>>> + serial3 = &uart3;
>>> + };
>>> +
>>> + memory@40000000 {
>>> + device_type = "memory";
>>> + reg = <0 0x40000000 0 0x80000000>;
>>> + };
>>> +
>>> + backlight_lcd: backlight_lcd {
>>> + compatible = "pwm-backlight";
>>> + pwms = <&pwm0 0 1000000>;
>>> + brightness-levels = <
>>> + 0 16 32 48 64 80 96 112
>>> + 128 144 160 176 192 208 224 240
>>> + 255
>>> + >;
>>> + default-brightness-level = <9>;
>>> + power-supply = <&bl_fixed_reg>;
>>> + enable-gpios = <&pio 95 GPIO_ACTIVE_HIGH>;
>>> +
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&disp_pwm0_pins>;
>>> + status = "okay";
>>> + };
>>> +
>>> + bl_fixed_reg: fixedregulator@2 {
>>> + compatible = "regulator-fixed";
>>> + regulator-name = "bl_fixed";
>>> + regulator-min-microvolt = <1800000>;
>>> + regulator-max-microvolt = <1800000>;
>>> + startup-delay-us = <1000>;
>>> + enable-active-high;
>>> + gpio = <&pio 32 GPIO_ACTIVE_HIGH>;
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&bl_fixed_pins>;
>>> + };
>>> +
>>> + chosen {
>>> + stdout-path = &uart0;
>>> + };
>>> +
>>> + gpio_keys: gpio-keys {
>>> + compatible = "gpio-keys";
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&gpio_keys_pins>;
>>> +
>>> + lid {
>>> + label = "Lid";
>>> + gpios = <&pio 69 GPIO_ACTIVE_LOW>;
>>> + linux,code = <0>; /* SW_LID */
>>> + linux,input-type = <5>; /* EV_SW */
>>> + gpio-key,wakeup;
>>> + };
>>> +
>>> + power {
>>> + label = "Power";
>>> + gpios = <&pio 14 GPIO_ACTIVE_HIGH>;
>>> + linux,code = <KEY_POWER>;
>>> + debounce-interval = <30>;
>>> + gpio-key,wakeup;
>>> + };
>>> +
>>> + tablet_mode {
>>> + label = "Tablet_mode";
>>> + gpios = <&pio 121 GPIO_ACTIVE_HIGH>;
>>> + linux,code = <1>; /* SW_TABLET_MODE */
>>
>> can't we use SW_TABLET_MODE fomr linux-event-codes.h?
>>
> Will fix this.
>>> + linux,input-type = <5>; /* EV_SW */
>>
>> same here.
>>
>>> + gpio-key,wakeup;
>>> + };
>>> +
>>> + volume_down {
>>> + label = "Volume_down";
>>> + gpios = <&pio 123 GPIO_ACTIVE_LOW>;
>>> + linux,code = <KEY_VOLUMEDOWN>;
>>> + };
>>> +
>>> + volume_up {
>>> + label = "Volume_up";
>>> + gpios = <&pio 124 GPIO_ACTIVE_LOW>;
>>> + linux,code = <KEY_VOLUMEUP>;
>>> + };
>>> + };
>>> +
>>> + panel: panel {
>>> + compatible = "lg,lp120up1";
>>> + power-supply = <&panel_fixed_3v3>;
>>> + ddc-i2c-bus = <&i2c0>;
>>> + backlight = <&backlight_lcd>;
>>> +
>>> + port {
>>> + panel_in: endpoint {
>>> + remote-endpoint = <&ps8640_out>;
>>> + };
>>> + };
>>> + };
>>> +
>>> + panel_fixed_3v3: regulator@1 {
>>> + compatible = "regulator-fixed";
>>> + regulator-name = "PANEL_3V3";
>>> + regulator-min-microvolt = <3300000>;
>>> + regulator-max-microvolt = <3300000>;
>>> + enable-active-high;
>>> + gpio = <&pio 41 GPIO_ACTIVE_HIGH>;
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&panel_fixed_pins>;
>>> + };
>>> +
>>> + ps8640_fixed_1v2: regulator@2 {
>>> + compatible = "regulator-fixed";
>>> + regulator-name = "PS8640_1V2";
>>> + regulator-min-microvolt = <1200000>;
>>> + regulator-max-microvolt = <1200000>;
>>> + regulator-enable-ramp-delay = <2000>;
>>> + enable-active-high;
>>> + regulator-boot-on;
>>> + gpio = <&pio 30 GPIO_ACTIVE_HIGH>;
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&ps8640_fixed_pins>;
>>> + };
>>> +
>>> + sdio_fixed_3v3: fixedregulator@0 {
>>> + compatible = "regulator-fixed";
>>> + regulator-name = "3V3";
>>> + regulator-min-microvolt = <3300000>;
>>> + regulator-max-microvolt = <3300000>;
>>> + gpio = <&pio 85 GPIO_ACTIVE_HIGH>;
>>
>> we don't need to set the pincontroller mux here?
>>
> Will double check on schematic and add it.
>>> + };
>>> +
>>> + sound: sound {
>>> + compatible = "mediatek,mt8173-rt5650";
>>> + mediatek,audio-codec = <&rt5650 &hdmi0>;
>>> + mediatek,platform = <&afe>;
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&aud_i2s2>;
>>> +
>>> + mediatek,mclk = <1>;
>>> + codec-capture {
>>> + sound-dai = <&rt5650 1>;
>>> + };
>>> + };
>>> +
>>> + hdmicon: connector {
>>> + compatible = "hdmi-connector";
>>> + label = "hdmi";
>>> + type = "a";
>>> + ddc-i2c-bus = <&hdmiddc0>;
>>> +
>>> + port {
>>> + hdmi_connector_in: endpoint {
>>> + remote-endpoint = <&hdmi0_out>;
>>> + };
>>> + };
>>> + };
>>> +};
>>> +
>>> +&cec {
>>> + status = "okay";
>>> +};
>>> +
>>> +&cpu0 {
>>> + proc-supply = <&mt6397_vpca15_reg>;
>>> +};
>>> +
>>> +&cpu1 {
>>> + proc-supply = <&mt6397_vpca15_reg>;
>>> +};
>>> +
>>> +&cpu2 {
>>> + proc-supply = <&da9211_vcpu_reg>;
>>> + sram-supply = <&mt6397_vsramca7_reg>;
>>> +};
>>> +
>>> +&cpu3 {
>>> + proc-supply = <&da9211_vcpu_reg>;
>>> + sram-supply = <&mt6397_vsramca7_reg>;
>>> +};
>>> +
>>> +&cpu_thermal {
>>> + sustainable-power = <4500>; /* milliwatts */
>>> + trips {
>>> + threshold: trip-point@0 {
>>> + temperature = <60000>;
>>> + };
>>> +
>>> + target: trip-point@1 {
>>> + temperature = <65000>;
>>> + };
>>> + };
>>> +};
>>> +
>>> +&dsi0 {
>>> + status = "okay";
>>> + ports {
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> +
>>> + port@1 {
>>> + dsi0_out: endpoint {
>>> + remote-endpoint = <&ps8640_in>;
>>> + };
>>> + };
>>> + };
>>> +};
>>> +
>>> +&dpi0 {
>>> + status = "okay";
>>> +};
>>> +
>>> +&hdmi0 {
>>> + status = "okay";
>>> + ports {
>>> + port@1 {
>>> + reg = <1>;
>>> +
>>> + hdmi0_out: endpoint {
>>> + remote-endpoint = <&hdmi_connector_in>;
>>> + };
>>> + };
>>> + };
>>> +};
>>> +
>>> +&hdmi_phy {
>>> + status = "okay";
>>> + mediatek,ibias = <0xc>;
>>> +};
>>> +
>>> +&i2c0 {
>>> + status = "okay";
>>> +
>>> + rt5650: audio-codec@1a {
>>> + compatible = "realtek,rt5650";
>>> + reg = <0x1a>;
>>> + avdd-supply = <&mt6397_vgp1_reg>;
>>> + cpvdd-supply = <&mt6397_vcama_reg>;
>>
>> Hm, only defined for "realtek,rt5663", I suppose that's an inconsistency in the
>> binding documentation. Can you please double check?
>>
> This one? https://github.com/torvalds/linux/blob/master/sound/soc/codecs/rt5645.c#L3582
>
Yes, I checked myself and send a patch to fix the binding description, which was
missing the two suppliers.
>>> + interrupt-parent = <&pio>;
>>> + interrupts = <3 IRQ_TYPE_EDGE_BOTH>;
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&rt5650_irq>;
>>> + #sound-dai-cells = <1>;
>>> + realtek,dmic1-data-pin = <2>;
>>> + realtek,jd-mode = <2>;
>>> + };
>>> +
>>> + ps8640: edp-bridge@8 {
>>> + compatible = "parade,ps8640";
>>> + reg = <0x8>;
>>> + powerdown-gpios = <&pio 127 GPIO_ACTIVE_LOW>;
>>> + reset-gpios = <&pio 115 GPIO_ACTIVE_LOW>;
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&ps8640_pins>;
>>> + vdd12-supply = <&ps8640_fixed_1v2>;
>>> + vdd33-supply = <&mt6397_vgp2_reg>;
>>> +
>>> + ports {
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> +
>>> + port@0 {
>>> + reg = <0>;
>>> +
>>> + ps8640_in: endpoint {
>>> + remote-endpoint = <&dsi0_out>;
>>> + };
>>> + };
>>> +
>>> + port@1 {
>>> + reg = <1>;
>>> +
>>> + ps8640_out: endpoint {
>>> + remote-endpoint = <&panel_in>;
>>> + };
>>> + };
>>> + };
>>> + };
>>> +};
>>> +
>>> +&i2c1 {
>>> + clock-frequency = <1500000>;
>>> + status = "okay";
>>> +
>>> + da9211: da9211@68 {
>>> + compatible = "dlg,da9211";
>>> + reg = <0x68>;
>>> +
>>
>> no interrupts? binding description have this stated as required. what happens
>> when the device raises an interrupt?
> Will double check on schematic and add it.
>>
>>> + regulators {
>>> + da9211_vcpu_reg: BUCKA {
>>> + regulator-name = "VBUCKA";
>>> + regulator-min-microvolt = < 700000>;
>>> + regulator-max-microvolt = <1310000>;
>>> + regulator-min-microamp = <2000000>;
>>> + regulator-max-microamp = <4400000>;
>>> + regulator-ramp-delay = <10000>;
>>> + regulator-always-on;
>>> + regulator-allowed-modes = <0 1>;
>>> + };
>>> +
>>> + da9211_vgpu_reg: BUCKB {
>>> + regulator-name = "VBUCKB";
>>> + regulator-min-microvolt = < 700000>;
>>> + regulator-max-microvolt = <1310000>;
>>> + regulator-min-microamp = <2000000>;
>>> + regulator-max-microamp = <3000000>;
>>> + regulator-ramp-delay = <10000>;
>>> + };
>>> + };
>>> + };
>>> +};
>>> +
>>> +&i2c2 {
>>> + status = "okay";
>>> +
>>> + tpm: tpm@20 {
>>> + compatible = "infineon,slb9645tt";
>>> + reg = <0x20>;
>>> + powered-while-suspended;
>>> + };
>>> +};
>>> +
>>> +&i2c3 {
>>> + clock-frequency = <400000>;
>>> + status = "okay";
>>> +
>>> + touchscreen: touchscreen@10 {
>>> + compatible = "elan,ekth3500";
>>> + reg = <0x10>;
>>> + interrupt-parent = <&pio>;
>>> + interrupts = <88 IRQ_TYPE_LEVEL_LOW>;
>>> + };
>>> +};
>>> +
>>> +&i2c4 {
>>> + clock-frequency = <400000>;
>>> + status = "okay";
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&trackpad_irq>;
>>
>> Why not move the pinctrl properties into the trackpad node?
>>
> As second source trackpad device and original device shares same
> compatible string (rev id), we need to add 2nd trackpad node here.
> According to previous log (since I don't have a second source trackpad
> device to test), adding pinctrl in each trackpad node, there would be
> error:
> [ 0.643501] mediatek-mt8173-pinctrl 1000b000.pinctrl: pin URXD3
> already requested by 7-0015; cannot claim for 7-002c
> [ 0.643525] mediatek-mt8173-pinctrl 1000b000.pinctrl: pin-117
> (7-002c) status -22
> [ 0.643548] mediatek-mt8173-pinctrl 1000b000.pinctrl: could not
> request pin 117 (URXD3) from group URXD3 on device 1000b000.pinctrl
> [ 0.643568] i2c_hid 7-002c: Error applying setting, reverse things back
> [ 0.643867] i2c 7-002c: Driver i2c_hid requests probe deferral
>
>
I think we can fix this, if we create the aforementioned two board DTS files.
Correct?
>>> +
>>> + trackpad: trackpad@15 {
>>> + compatible = "elan,ekth3000";
>>> + interrupt-parent = <&pio>;
>>> + interrupts = <117 IRQ_TYPE_LEVEL_LOW>;
>>> + reg = <0x15>;
>>> + vcc-supply = <&mt6397_vgp6_reg>;
>>> + wakeup-source;
>>> + };
>>> +};
>>> +
>>> +&mipi_tx0 {
>>> + status = "okay";
>>> +};
>>> +
>>> +&mmc0 {
>>> + status = "okay";
>>> + pinctrl-names = "default", "state_uhs";
>>> + pinctrl-0 = <&mmc0_pins_default>;
>>> + pinctrl-1 = <&mmc0_pins_uhs>;
>>> + bus-width = <8>;
>>> + max-frequency = <200000000>;
>>> + cap-mmc-highspeed;
>>> + mmc-hs200-1_8v;
>>> + mmc-hs400-1_8v;
>>> + cap-mmc-hw-reset;
>>> + hs400-ds-delay = <0x14015>;
>>> + mediatek,hs200-cmd-int-delay=<30>;
>>> + mediatek,hs400-cmd-int-delay=<14>;
>>> + mediatek,hs400-cmd-resp-sel-rising;
>>> + vmmc-supply = <&mt6397_vemc_3v3_reg>;
>>> + vqmmc-supply = <&mt6397_vio18_reg>;
>>> + assigned-clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>;
>>> + assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL_D2>;
>>> + non-removable;
>>> +};
>>> +
>>> +&mmc1 {
>>> + status = "okay";
>>> + pinctrl-names = "default", "state_uhs";
>>> + pinctrl-0 = <&mmc1_pins_default>;
>>> + pinctrl-1 = <&mmc1_pins_uhs>;
>>> + bus-width = <4>;
>>> + max-frequency = <200000000>;
>>> + cap-sd-highspeed;
>>> + sd-uhs-sdr50;
>>> + sd-uhs-sdr104;
>>> + cd-gpios = <&pio 1 GPIO_ACTIVE_HIGH>;
>>> + vmmc-supply = <&mt6397_vmch_reg>;
>>> + vqmmc-supply = <&mt6397_vmc_reg>;
>>> +};
>>> +
>>> +&mmc3 {
>>> + status = "okay";
>>> + pinctrl-names = "default", "state_uhs";
>>> + pinctrl-0 = <&mmc3_pins_default>;
>>> + pinctrl-1 = <&mmc3_pins_uhs>;
>>> + bus-width = <4>;
>>> + max-frequency = <200000000>;
>>> + cap-sd-highspeed;
>>> + sd-uhs-sdr50;
>>> + sd-uhs-sdr104;
>>> + sdr104-clk-delay = <5>;
>>
>> Not an upstream property, please delete it.
>>
>>> + keep-power-in-suspend;
>>> + enable-sdio-wakeup;
>>> + cap-sdio-irq;
>>> + vmmc-supply = <&sdio_fixed_3v3>;
>>> + vqmmc-supply = <&mt6397_vgp3_reg>;
>>> + non-removable;
>>> + cap-power-off-card;
>>> +
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> +
>>> + btmrvl: btmrvl@2 {
>>> + compatible = "marvell,sd8897-bt";
>>> + reg = <2>;
>>> + interrupt-parent = <&pio>;
>>> + interrupts = <119 IRQ_TYPE_LEVEL_LOW>;
>>> + marvell,wakeup-pin = /bits/ 16 <0x0d>;
>>> + marvell,wakeup-gap-ms = /bits/ 16 <0x64>;
>>> + };
>>> +
>>> + mwifiex: mwifiex@1 {
>>> + compatible = "marvell,sd8897";
>>> + reg = <1>;
>>> + interrupt-parent = <&pio>;
>>> + interrupts = <38 IRQ_TYPE_LEVEL_LOW>;
>>> + marvell,wakeup-pin = <3>;
>>> + marvell,caldata_ed_mac = /bits/ 8 <
>>> +0x01 0x00 0x07 0x00 0x14 0x00 0x01 0x00 0x00 0x00 0x12 0x00 0x02 0x00 0x01 0x00
>>> +0x01 0x00 0x00 0x00 0x12 0x00 0x02 0x00 0x01 0x00
>>> + >;
>>
>> Not an upstream property, please delete.
>>
>>> + };
>>> +};
>>> +
>>> +&nor_flash {
>>> + status = "okay";
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&nor_gpio1_pins>;
>>> + bus-width = <8>;
>>> + max-frequency = <50000000>;
>>> + non-removable;
>>> + flash@0 {
>>> + compatible = "jedec,spi-nor";
>>> + reg = <0>;
>>> + };
>>> +};
>>> +
>>> +&pio {
>>> + aud_i2s2: aud_i2s2 {
>>> + pins1 {
>>> + pinmux = <MT8173_PIN_128_I2S0_LRCK__FUNC_I2S1_WS>,
>>> + <MT8173_PIN_129_I2S0_BCK__FUNC_I2S1_BCK>,
>>> + <MT8173_PIN_130_I2S0_MCK__FUNC_I2S1_MCK>,
>>> + <MT8173_PIN_131_I2S0_DATA0__FUNC_I2S1_DO_1>,
>>> + <MT8173_PIN_12_EINT12__FUNC_I2S2_WS>,
>>> + <MT8173_PIN_13_EINT13__FUNC_I2S2_BCK>,
>>> + <MT8173_PIN_132_I2S0_DATA1__FUNC_I2S2_DI_2>;
>>> + bias-pull-down;
>>> + };
>>> + };
>>> +
>>> + bl_fixed_pins: bl_fixed_pins {
>>> + pins1 {
>>> + pinmux = <MT8173_PIN_32_UTXD2__FUNC_GPIO32>;
>>> + output-low;
>>> + };
>>> + };
>>> +
>>> + bt_wake_pins: bt_wake_pins {
>>> + pins1 {
>>> + pinmux = <MT8173_PIN_119_KPROW0__FUNC_GPIO119>;
>>> + bias-pull-up;
>>> + };
>>> + };
>>> +
>>> + disp_pwm0_pins: disp_pwm0_pins {
>>> + pins1 {
>>> + pinmux = <MT8173_PIN_87_DISP_PWM0__FUNC_DISP_PWM0>;
>>> + output-low;
>>> + };
>>> + };
>>> +
>>> + gpio_keys_pins: gpio_keys_pins {
>>> + volume_pins {
>>> + pinmux = <MT8173_PIN_123_KPCOL1__FUNC_GPIO123>,
>>> + <MT8173_PIN_124_KPCOL2__FUNC_GPIO124>;
>>> + bias-pull-up;
>>> + };
>>> +
>>> + tablet_mode_pins {
>>> + pinmux = <MT8173_PIN_121_KPROW2__FUNC_GPIO121>;
>>> + bias-pull-up;
>>> + };
>>> + };
>>> +
>>> + hdmi_mux_pins: hdmi_mux_pins {
>>> + pins1 {
>>> + pinmux = <MT8173_PIN_36_DAISYNC__FUNC_GPIO36>;
>>> + };
>>> + };
>>> +
>>> + mmc0_pins_default: mmc0default {
>>> + pins_cmd_dat {
>>> + pinmux = <MT8173_PIN_57_MSDC0_DAT0__FUNC_MSDC0_DAT0>,
>>> + <MT8173_PIN_58_MSDC0_DAT1__FUNC_MSDC0_DAT1>,
>>> + <MT8173_PIN_59_MSDC0_DAT2__FUNC_MSDC0_DAT2>,
>>> + <MT8173_PIN_60_MSDC0_DAT3__FUNC_MSDC0_DAT3>,
>>> + <MT8173_PIN_61_MSDC0_DAT4__FUNC_MSDC0_DAT4>,
>>> + <MT8173_PIN_62_MSDC0_DAT5__FUNC_MSDC0_DAT5>,
>>> + <MT8173_PIN_63_MSDC0_DAT6__FUNC_MSDC0_DAT6>,
>>> + <MT8173_PIN_64_MSDC0_DAT7__FUNC_MSDC0_DAT7>,
>>> + <MT8173_PIN_66_MSDC0_CMD__FUNC_MSDC0_CMD>;
>>> + bias-pull-up;
>>> + };
>>> +
>>> + pins_clk {
>>> + pinmux = <MT8173_PIN_65_MSDC0_CLK__FUNC_MSDC0_CLK>;
>>> + bias-pull-down;
>>
>> identation.
>>
>>> + };
>>> +
>>> + pins_rst {
>>> + pinmux = <MT8173_PIN_68_MSDC0_RST___FUNC_MSDC0_RSTB>;
>>> + bias-pull-up;
>>> + };
>>> + };
>>> +
>>> + mmc1_pins_default: mmc1default {
>>> + pins_cmd_dat {
>>> + pinmux = <MT8173_PIN_73_MSDC1_DAT0__FUNC_MSDC1_DAT0>,
>>> + <MT8173_PIN_74_MSDC1_DAT1__FUNC_MSDC1_DAT1>,
>>> + <MT8173_PIN_75_MSDC1_DAT2__FUNC_MSDC1_DAT2>,
>>> + <MT8173_PIN_76_MSDC1_DAT3__FUNC_MSDC1_DAT3>,
>>> + <MT8173_PIN_78_MSDC1_CMD__FUNC_MSDC1_CMD>;
>>> + input-enable;
>>> + drive-strength = <MTK_DRIVE_4mA>;
>>> + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
>>> + };
>>> +
>>> + pins_clk {
>>> + pinmux = <MT8173_PIN_77_MSDC1_CLK__FUNC_MSDC1_CLK>;
>>> + bias-pull-down;
>>> + drive-strength = <MTK_DRIVE_4mA>;
>>> + };
>>> +
>>> + pins_insert {
>>> + pinmux = <MT8173_PIN_1_EINT1__FUNC_GPIO1>;
>>> + bias-pull-up;
>>> + };
>>> + };
>>> +
>>> + mmc3_pins_default: mmc3default {
>>> + pins_dat {
>>> + pinmux = <MT8173_PIN_22_MSDC3_DAT0__FUNC_MSDC3_DAT0>,
>>> + <MT8173_PIN_23_MSDC3_DAT1__FUNC_MSDC3_DAT1>,
>>> + <MT8173_PIN_24_MSDC3_DAT2__FUNC_MSDC3_DAT2>,
>>> + <MT8173_PIN_25_MSDC3_DAT3__FUNC_MSDC3_DAT3>;
>>> + input-enable;
>>> + drive-strength = <MTK_DRIVE_8mA>;
>>> + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
>>> + };
>>> +
>>> + pins_cmd {
>>> + pinmux = <MT8173_PIN_27_MSDC3_CMD__FUNC_MSDC3_CMD>;
>>> + input-enable;
>>> + drive-strength = <MTK_DRIVE_8mA>;
>>> + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
>>> + };
>>> +
>>> + pins_clk {
>>> + pinmux = <MT8173_PIN_26_MSDC3_CLK__FUNC_MSDC3_CLK>;
>>> + bias-pull-down;
>>> + drive-strength = <MTK_DRIVE_8mA>;
>>> + };
>>> +
>>> + pins_pdn {
>>> + pinmux = <MT8173_PIN_85_AUD_DAT_MOSI__FUNC_GPIO85>;
>>> + output-low;
>>> + };
>>> + };
>>> +
>>> + mmc0_pins_uhs: mmc0 {
>>> + pins_cmd_dat {
>>> + pinmux = <MT8173_PIN_57_MSDC0_DAT0__FUNC_MSDC0_DAT0>,
>>> + <MT8173_PIN_58_MSDC0_DAT1__FUNC_MSDC0_DAT1>,
>>> + <MT8173_PIN_59_MSDC0_DAT2__FUNC_MSDC0_DAT2>,
>>> + <MT8173_PIN_60_MSDC0_DAT3__FUNC_MSDC0_DAT3>,
>>> + <MT8173_PIN_61_MSDC0_DAT4__FUNC_MSDC0_DAT4>,
>>> + <MT8173_PIN_62_MSDC0_DAT5__FUNC_MSDC0_DAT5>,
>>> + <MT8173_PIN_63_MSDC0_DAT6__FUNC_MSDC0_DAT6>,
>>> + <MT8173_PIN_64_MSDC0_DAT7__FUNC_MSDC0_DAT7>,
>>> + <MT8173_PIN_66_MSDC0_CMD__FUNC_MSDC0_CMD>;
>>> + input-enable;
>>> + drive-strength = <MTK_DRIVE_6mA>;
>>> + bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
>>> + };
>>> +
>>> + pins_clk {
>>> + pinmux = <MT8173_PIN_65_MSDC0_CLK__FUNC_MSDC0_CLK>;
>>> + drive-strength = <MTK_DRIVE_6mA>;
>>> + bias-pull-down = <MTK_PUPD_SET_R1R0_01>;
>>> + };
>>> +
>>> + pins_ds {
>>> + pinmux = <MT8173_PIN_67_MSDC0_DSL__FUNC_MSDC0_DSL>;
>>> + drive-strength = <MTK_DRIVE_10mA>;
>>> + bias-pull-down = <MTK_PUPD_SET_R1R0_01>;
>>> + };
>>> +
>>> + pins_rst {
>>> + pinmux = <MT8173_PIN_68_MSDC0_RST___FUNC_MSDC0_RSTB>;
>>> + bias-pull-up;
>>> + };
>>> + };
>>> +
>>> + mmc1_pins_uhs: mmc1 {
>>> + pins_cmd_dat {
>>> + pinmux = <MT8173_PIN_73_MSDC1_DAT0__FUNC_MSDC1_DAT0>,
>>> + <MT8173_PIN_74_MSDC1_DAT1__FUNC_MSDC1_DAT1>,
>>> + <MT8173_PIN_75_MSDC1_DAT2__FUNC_MSDC1_DAT2>,
>>> + <MT8173_PIN_76_MSDC1_DAT3__FUNC_MSDC1_DAT3>,
>>> + <MT8173_PIN_78_MSDC1_CMD__FUNC_MSDC1_CMD>;
>>> + input-enable;
>>> + drive-strength = <MTK_DRIVE_6mA>;
>>> + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
>>> + };
>>> +
>>> + pins_clk {
>>> + pinmux = <MT8173_PIN_77_MSDC1_CLK__FUNC_MSDC1_CLK>;
>>> + drive-strength = <MTK_DRIVE_8mA>;
>>> + bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
>>> + };
>>> + };
>>> +
>>> + mmc3_pins_uhs: mmc3 {
>>> + pins_dat {
>>> + pinmux = <MT8173_PIN_22_MSDC3_DAT0__FUNC_MSDC3_DAT0>,
>>> + <MT8173_PIN_23_MSDC3_DAT1__FUNC_MSDC3_DAT1>,
>>> + <MT8173_PIN_24_MSDC3_DAT2__FUNC_MSDC3_DAT2>,
>>> + <MT8173_PIN_25_MSDC3_DAT3__FUNC_MSDC3_DAT3>;
>>> + input-enable;
>>> + drive-strength = <MTK_DRIVE_8mA>;
>>> + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
>>> + };
>>> +
>>> + pins_cmd {
>>> + pinmux = <MT8173_PIN_27_MSDC3_CMD__FUNC_MSDC3_CMD>;
>>> + input-enable;
>>> + drive-strength = <MTK_DRIVE_8mA>;
>>> + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
>>> + };
>>> +
>>> + pins_clk {
>>> + pinmux = <MT8173_PIN_26_MSDC3_CLK__FUNC_MSDC3_CLK>;
>>> + drive-strength = <MTK_DRIVE_8mA>;
>>> + bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
>>> + };
>>> + };
>>> +
>>> + nor_gpio1_pins: nor {
>>> + pins1 {
>>> + pinmux = <MT8173_PIN_6_EINT6__FUNC_SFCS0>,
>>> + <MT8173_PIN_7_EINT7__FUNC_SFHOLD>,
>>> + <MT8173_PIN_8_EINT8__FUNC_SFIN>;
>>> + input-enable;
>>> + drive-strength = <MTK_DRIVE_4mA>;
>>> + bias-pull-up;
>>> + };
>>> +
>>> + pins2 {
>>> + pinmux = <MT8173_PIN_5_EINT5__FUNC_SFOUT>;
>>> + drive-strength = <MTK_DRIVE_4mA>;
>>> + bias-pull-up;
>>> + };
>>> +
>>> + pins_clk {
>>> + pinmux = <MT8173_PIN_9_EINT9__FUNC_SFCK>;
>>> + input-enable;
>>> + drive-strength = <MTK_DRIVE_4mA>;
>>> + bias-pull-up;
>>> + };
>>> + };
>>> +
>>> + panel_fixed_pins: panel_fixed_pins {
>>> + pins1 {
>>> + pinmux = <MT8173_PIN_41_CMMCLK__FUNC_GPIO41>;
>>> + };
>>> + };
>>> +
>>> + ps8640_pins: ps8640_pins {
>>> + pins1 {
>>> + pinmux = <MT8173_PIN_92_PCM_CLK__FUNC_GPIO92>,
>>> + <MT8173_PIN_115_URTS0__FUNC_GPIO115>,
>>> + <MT8173_PIN_127_LCM_RST__FUNC_GPIO127>;
>>> + };
>>> + };
>>> +
>>> + ps8640_fixed_pins: ps8640_fixed_pins {
>>> + pins1 {
>>> + pinmux = <MT8173_PIN_30_URTS2__FUNC_GPIO30>;
>>> + };
>>> + };
>>> +
>>> + rt5650_irq: rt5650_irq {
>>> + pins1 {
>>> + pinmux = <MT8173_PIN_3_EINT3__FUNC_GPIO3>;
>>> + bias-pull-down;
>>> + };
>>> + };
>>> +
>>> + spi_pins_a: spi1 {
>>> + pins1 {
>>> + pinmux = <MT8173_PIN_0_EINT0__FUNC_GPIO0>;
>>> + bias-pull-up;
>>> + };
>>> +
>>> + pins_spi {
>>> + pinmux = <MT8173_PIN_102_MSDC2_DAT2__FUNC_SPI_CK_1_>,
>>> + <MT8173_PIN_103_MSDC2_DAT3__FUNC_SPI_MI_1_>,
>>> + <MT8173_PIN_104_MSDC2_CLK__FUNC_SPI_MO_1_>,
>>> + <MT8173_PIN_105_MSDC2_CMD__FUNC_SPI_CS_1_>;
>>> + bias-disable;
>>> + };
>>> + };
>>> +
>>> + trackpad_irq: trackpad_irq {
>>> + pins1 {
>>> + pinmux = <MT8173_PIN_117_URXD3__FUNC_GPIO117>;
>>> + input-enable;
>>> + bias-pull-up;
>>> + };
>>> + };
>>> +
>>> + usb_pins: usb@0 {
>>> + pins1 {
>>> + pinmux = <MT8173_PIN_101_MSDC2_DAT1__FUNC_GPIO101>;
>>> + output-high;
>>> + bias-disable;
>>> + };
>>> + };
>>> +
>>> + wifi_wake_pins: wifi_wake_pins {
>>> + pins1 {
>>> + pinmux = <MT8173_PIN_38_CONN_RST__FUNC_GPIO38>;
>>> + bias-pull-up;
>>> + };
>>> + };
>>> +};
>>> +
>>> +&pwm0 {
>>> + status = "okay";
>>> +};
>>> +
>>> +&pwrap {
>>> + pmic: mt6397 {
>>> + compatible = "mediatek,mt6397";
>>> + #address-cells = <1>;
>>> + #size-cells = <1>;
>>> + interrupt-parent = <&pio>;
>>> + interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
>>> + interrupt-controller;
>>> + #interrupt-cells = <2>;
>>> +
>>> + mt6397rtc: mt6397rtc {
>>
>> AFAIK this should be
>> rtc: mt6397rtc {
>>
>> Please fix that for all subnodes.
>>
> Will fix in next version
>>> + compatible = "mediatek,mt6397-rtc";
>>> + };
>>> +
>>> + syscfg_pctl_pmic: syscfg_pctl_pmic@c000 {
>>> + compatible = "mediatek,mt6397-pctl-pmic-syscfg",
>>> + "syscon";
>>> + reg = <0 0x0000c000 0 0x0108>;
>>
>> not an upstream compatible, please delete the node.
>>
I think my comment was not correct. I'll have to dig more to understand why we
have a compatible without a binding description.
Regards,
Matthias
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH v2 2/2] arm64: dts: mediatek: add mt8173 elm and hana board
2020-01-14 15:10 ` Matthias Brugger
@ 2020-01-14 15:33 ` Hsin-Yi Wang
2020-01-15 8:53 ` Hsin-Yi Wang
1 sibling, 0 replies; 14+ messages in thread
From: Hsin-Yi Wang @ 2020-01-14 15:33 UTC (permalink / raw)
To: Matthias Brugger
Cc: Mark Rutland, Devicetree List, Nicolas Boichat, lkml,
Daniel Kurtz, Rob Herring, linux-mediatek,
Enric Balletbo i Serra,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE
On Tue, Jan 14, 2020 at 11:10 PM Matthias Brugger
<matthias.bgg@gmail.com> wrote:
>
>
>
> On 13/01/2020 19:01, Hsin-Yi Wang wrote:
> > On Fri, Jan 10, 2020 at 9:42 PM Matthias Brugger <matthias.bgg@gmail.com> wrote:
> >>
> >>
> > Thanks, I will address the comments and send next version
> >>
> >> On 10/01/2020 08:37, Hsin-Yi Wang wrote:
> >>> Elm is Acer Chromebook R13. Hana is Lenovo Chromebook. Both uses mt8173
> >>> SoC.
> >>>
> >>> Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
> >>> ---
> >>> Changes in v2:
> >>> - remove downstream nodes and unused nodes
> >>> - use GPIO_ACTIVE_LOW for ps8640 gpios
> >>> - move trackpad to hana
> >>> ---
> >>> arch/arm64/boot/dts/mediatek/Makefile | 3 +
> >>> .../dts/mediatek/mt8173-elm-hana-rev7.dts | 27 +
> >>> .../boot/dts/mediatek/mt8173-elm-hana.dts | 16 +
> >>> .../boot/dts/mediatek/mt8173-elm-hana.dtsi | 60 +
> >>> arch/arm64/boot/dts/mediatek/mt8173-elm.dts | 15 +
> >>> arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi | 1040 +++++++++++++++++
> >>> 6 files changed, 1161 insertions(+)
> >>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts
> >>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts
> >>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dtsi
> >>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm.dts
> >>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi
> >>>
> >>> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> >>> index 458bbc422a94..b45a45a565a1 100644
> >>> --- a/arch/arm64/boot/dts/mediatek/Makefile
> >>> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> >>> @@ -6,5 +6,8 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb
> >>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
> >>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
> >>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
> >>> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm.dtb
> >>> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana.dtb
> >>> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana-rev7.dtb
> >>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-evb.dtb
> >>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-evb.dtb
> >>> diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts
> >>> new file mode 100644
> >>> index 000000000000..a3616bc3d859
> >>> --- /dev/null
> >>> +++ b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts
> >>> @@ -0,0 +1,27 @@
> >>> +// SPDX-License-Identifier: GPL-2.0-only
> >>> +/*
> >>> + * Copyright 2019 MediaTek Inc.
> >>> + */
> >>> +
> >>> +/dts-v1/;
> >>> +#include "mt8173-elm-hana.dtsi"
> >>> +
> >>> +/ {
> >>> + model = "Mediatek Hana rev7 board";
> >>> + compatible = "google,hana-rev7", "mediatek,mt8173";
> >>> +};
> >>> +
> >>> +&cpu_thermal {
> >>> + trips {
> >>> + cpu_crit: cpu_crit@0 {
> >>> + temperature = <100000>;
> >>> + type = "critical";
> >>> + };
> >>> + };
> >>> +};
> >>> +
> >>> +&gpio_keys {
> >>> + /delete-node/tablet_mode;
> >>> + /delete-node/volume_down;
> >>> + /delete-node/volume_up;
> >>> +};
> >>> \ No newline at end of file
> >>> diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts
> >>> new file mode 100644
> >>> index 000000000000..8cbcc75192e3
> >>> --- /dev/null
> >>> +++ b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts
> >>> @@ -0,0 +1,16 @@
> >>> +// SPDX-License-Identifier: GPL-2.0-only
> >>> +/*
> >>> + * Copyright 2016 MediaTek Inc.
> >>> + */
> >>> +
> >>> +/dts-v1/;
> >>> +#include "mt8173-elm-hana.dtsi"
> >>> +
> >>> +/ {
> >>> + model = "Mediatek Hana rev0 board";
>
> If we can't make this more verbose, at least delete rev0, that's confusing.
> Should the name not be "Google Hana"?
>
Sure, Google Hana makes sense.
> >>> + compatible = "google,hana-rev6",
> >>> + "google,hana-rev5", "google,hana-rev4",
> >>> + "google,hana-rev3", "google,hana-rev2",
> >>> + "google,hana-rev1", "google,hana-rev0",
> >>> + "google,hana", "mediatek,mt8173";
> >>> +};
> >>
> >> I'm a bit confused about all this versions. Do you want to keep them for
> >> internal use, as I suppose only rev6 is available to the general public,
> >> correct? I'm fine with keeping the old revisions if that's of use for you,
> >> otherwise I'd prefer to delete them.
> > According to internal feedback system, at least rev3, rev6, rev7 are
> > in general public. I can delete rev0~rev2, since they are earlier
> > version device.
>
> If you don't plan to use the rev0 to rev2 in-house, then we can delete them.
>
> >>
> >> Model name could be more verbose.
> >>
> >>> \ No newline at end of file
> >>> diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dtsi b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dtsi
> >>> new file mode 100644
> >>> index 000000000000..35e12b290947
> >>> --- /dev/null
> >>> +++ b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dtsi
> >>> @@ -0,0 +1,60 @@
> >>> +// SPDX-License-Identifier: GPL-2.0-only
> >>> +/*
> >>> + * Copyright 2016 MediaTek Inc.
> >>> + */
> >>> +
> >>> +#include "mt8173-elm.dtsi"
> >>> +
> >>> +&i2c0 {
> >>> + clock-frequency = <200000>;
> >>> +};
> >>> +
> >>> +&i2c3 {
> >>> + touchscreen2: touchscreen@34 {
> >>> + compatible = "melfas,mip4_ts";
> >>> + reg = <0x34>;
> >>> + interrupt-parent = <&pio>;
> >>> + interrupts = <88 IRQ_TYPE_LEVEL_LOW>;
> >>> + };
> >>> +
> >>> + touchscreen3: touchscreen@20 {
> >>> + compatible = "hid-over-i2c";
> >>> + reg = <0x20>;
> >>> + hid-descr-addr = <0x0020>;
> >>> + interrupt-parent = <&pio>;
> >>> + interrupts = <88 IRQ_TYPE_LEVEL_LOW>;
> >>> + };
> >>
> >> In v1 you mentioned:
> >> "Partners wants to increase touchpad and touchscreen source (they choose
> >> synaptics) for hana 300e, and synaptics uses hid-over-i2c driver."
> >>
> >> So the partner uses the same compatible (google,hana-rev6?) for both devices?
> >>
> > Confirmed with others, second source devices share same compatible.
>
> We should create independent dts for the different boards. Like it is done for
> gru-scarlett. Doesn't the FW provide the sku number in the compatible string?
>
Since I don't have a second source device to verify, I checked with
SIE, and he said the sku number(board id) are same for device using
original trackpad and second source trackpad in hana's case. So I
don't think we can split them to independent dts.
> >>> +};
> >>> +
> >>> +&i2c4 {
> >>> + trackpad2: trackpad@2c {
> >>> + compatible = "hid-over-i2c";
> >>> + interrupt-parent = <&pio>;
> >>> + interrupts = <117 IRQ_TYPE_LEVEL_LOW>;
> >>> + reg = <0x2c>;
> >>> + hid-descr-addr = <0x0020>;
> >>> + wakeup-source;
> >>> + };
> >>> +};
> >>> +
> >>> +&mmc1 {
> >>> + wp-gpios = <&pio 42 GPIO_ACTIVE_HIGH>;
> >>> +};
> >>> +
> >>> +&pio {
> >>> + hdmi_mux_pins: hdmi_mux_pins {
> >>> + pins2 {
> >>> + pinmux = <MT8173_PIN_98_URTS1__FUNC_GPIO98>;
> >>> + bias-pull-up;
> >>> + output-high;
> >>> + };
> >>> + };
> >>> +
> >>> + mmc1_pins_default: mmc1default {
> >>> + pins_wp {
> >>> + pinmux = <MT8173_PIN_42_DSI_TE__FUNC_GPIO42>;
> >>> + input-enable;
> >>> + bias-pull-up;
> >>> + };
> >>> + };
> >>> +};
> >>> \ No newline at end of file
> >>> diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm.dts b/arch/arm64/boot/dts/mediatek/mt8173-elm.dts
> >>> new file mode 100644
> >>> index 000000000000..e5da2355760e
> >>> --- /dev/null
> >>> +++ b/arch/arm64/boot/dts/mediatek/mt8173-elm.dts
> >>> @@ -0,0 +1,15 @@
> >>> +// SPDX-License-Identifier: GPL-2.0-only
> >>> +/*
> >>> + * Copyright 2016 MediaTek Inc.
> >>> + */
> >>> +
> >>> +/dts-v1/;
> >>> +#include "mt8173-elm.dtsi"
> >>> +
> >>> +/ {
> >>> + model = "Mediatek Elm board";
> >>> + compatible = "google,elm-rev8", "google,elm-rev7", "google,elm-rev6",
> >>> + "google,elm-rev5", "google,elm-rev4", "google,elm-rev3",
> >>> + "google,elm-rev2", "google,elm-rev1",
> >>> + "google,elm", "mediatek,mt8173";
> >>> +};
> >>> \ No newline at end of file
> >>> diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi b/arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi
> >>> new file mode 100644
> >>> index 000000000000..2ac738bebe04
> >>> --- /dev/null
> >>> +++ b/arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi
> >>> @@ -0,0 +1,1040 @@
> >>> +// SPDX-License-Identifier: GPL-2.0-only
> >>> +/*
> >>> + * Copyright 2016 MediaTek Inc.
> >>> + */
> >>> +
> >>> +#include <dt-bindings/input/input.h>
> >>> +#include <dt-bindings/gpio/gpio.h>
> >>> +#include "mt8173.dtsi"
> >>> +
> >>> +/ {
> >>> + aliases {
> >>> + serial0 = &uart0;
> >>> + serial1 = &uart1;
> >>> + serial2 = &uart2;
> >>> + serial3 = &uart3;
> >>> + };
> >>> +
> >>> + memory@40000000 {
> >>> + device_type = "memory";
> >>> + reg = <0 0x40000000 0 0x80000000>;
> >>> + };
> >>> +
> >>> + backlight_lcd: backlight_lcd {
> >>> + compatible = "pwm-backlight";
> >>> + pwms = <&pwm0 0 1000000>;
> >>> + brightness-levels = <
> >>> + 0 16 32 48 64 80 96 112
> >>> + 128 144 160 176 192 208 224 240
> >>> + 255
> >>> + >;
> >>> + default-brightness-level = <9>;
> >>> + power-supply = <&bl_fixed_reg>;
> >>> + enable-gpios = <&pio 95 GPIO_ACTIVE_HIGH>;
> >>> +
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 = <&disp_pwm0_pins>;
> >>> + status = "okay";
> >>> + };
> >>> +
> >>> + bl_fixed_reg: fixedregulator@2 {
> >>> + compatible = "regulator-fixed";
> >>> + regulator-name = "bl_fixed";
> >>> + regulator-min-microvolt = <1800000>;
> >>> + regulator-max-microvolt = <1800000>;
> >>> + startup-delay-us = <1000>;
> >>> + enable-active-high;
> >>> + gpio = <&pio 32 GPIO_ACTIVE_HIGH>;
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 = <&bl_fixed_pins>;
> >>> + };
> >>> +
> >>> + chosen {
> >>> + stdout-path = &uart0;
> >>> + };
> >>> +
> >>> + gpio_keys: gpio-keys {
> >>> + compatible = "gpio-keys";
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 = <&gpio_keys_pins>;
> >>> +
> >>> + lid {
> >>> + label = "Lid";
> >>> + gpios = <&pio 69 GPIO_ACTIVE_LOW>;
> >>> + linux,code = <0>; /* SW_LID */
> >>> + linux,input-type = <5>; /* EV_SW */
> >>> + gpio-key,wakeup;
> >>> + };
> >>> +
> >>> + power {
> >>> + label = "Power";
> >>> + gpios = <&pio 14 GPIO_ACTIVE_HIGH>;
> >>> + linux,code = <KEY_POWER>;
> >>> + debounce-interval = <30>;
> >>> + gpio-key,wakeup;
> >>> + };
> >>> +
> >>> + tablet_mode {
> >>> + label = "Tablet_mode";
> >>> + gpios = <&pio 121 GPIO_ACTIVE_HIGH>;
> >>> + linux,code = <1>; /* SW_TABLET_MODE */
> >>
> >> can't we use SW_TABLET_MODE fomr linux-event-codes.h?
> >>
> > Will fix this.
> >>> + linux,input-type = <5>; /* EV_SW */
> >>
> >> same here.
> >>
> >>> + gpio-key,wakeup;
> >>> + };
> >>> +
> >>> + volume_down {
> >>> + label = "Volume_down";
> >>> + gpios = <&pio 123 GPIO_ACTIVE_LOW>;
> >>> + linux,code = <KEY_VOLUMEDOWN>;
> >>> + };
> >>> +
> >>> + volume_up {
> >>> + label = "Volume_up";
> >>> + gpios = <&pio 124 GPIO_ACTIVE_LOW>;
> >>> + linux,code = <KEY_VOLUMEUP>;
> >>> + };
> >>> + };
> >>> +
> >>> + panel: panel {
> >>> + compatible = "lg,lp120up1";
> >>> + power-supply = <&panel_fixed_3v3>;
> >>> + ddc-i2c-bus = <&i2c0>;
> >>> + backlight = <&backlight_lcd>;
> >>> +
> >>> + port {
> >>> + panel_in: endpoint {
> >>> + remote-endpoint = <&ps8640_out>;
> >>> + };
> >>> + };
> >>> + };
> >>> +
> >>> + panel_fixed_3v3: regulator@1 {
> >>> + compatible = "regulator-fixed";
> >>> + regulator-name = "PANEL_3V3";
> >>> + regulator-min-microvolt = <3300000>;
> >>> + regulator-max-microvolt = <3300000>;
> >>> + enable-active-high;
> >>> + gpio = <&pio 41 GPIO_ACTIVE_HIGH>;
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 = <&panel_fixed_pins>;
> >>> + };
> >>> +
> >>> + ps8640_fixed_1v2: regulator@2 {
> >>> + compatible = "regulator-fixed";
> >>> + regulator-name = "PS8640_1V2";
> >>> + regulator-min-microvolt = <1200000>;
> >>> + regulator-max-microvolt = <1200000>;
> >>> + regulator-enable-ramp-delay = <2000>;
> >>> + enable-active-high;
> >>> + regulator-boot-on;
> >>> + gpio = <&pio 30 GPIO_ACTIVE_HIGH>;
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 = <&ps8640_fixed_pins>;
> >>> + };
> >>> +
> >>> + sdio_fixed_3v3: fixedregulator@0 {
> >>> + compatible = "regulator-fixed";
> >>> + regulator-name = "3V3";
> >>> + regulator-min-microvolt = <3300000>;
> >>> + regulator-max-microvolt = <3300000>;
> >>> + gpio = <&pio 85 GPIO_ACTIVE_HIGH>;
> >>
> >> we don't need to set the pincontroller mux here?
> >>
> > Will double check on schematic and add it.
> >>> + };
> >>> +
> >>> + sound: sound {
> >>> + compatible = "mediatek,mt8173-rt5650";
> >>> + mediatek,audio-codec = <&rt5650 &hdmi0>;
> >>> + mediatek,platform = <&afe>;
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 = <&aud_i2s2>;
> >>> +
> >>> + mediatek,mclk = <1>;
> >>> + codec-capture {
> >>> + sound-dai = <&rt5650 1>;
> >>> + };
> >>> + };
> >>> +
> >>> + hdmicon: connector {
> >>> + compatible = "hdmi-connector";
> >>> + label = "hdmi";
> >>> + type = "a";
> >>> + ddc-i2c-bus = <&hdmiddc0>;
> >>> +
> >>> + port {
> >>> + hdmi_connector_in: endpoint {
> >>> + remote-endpoint = <&hdmi0_out>;
> >>> + };
> >>> + };
> >>> + };
> >>> +};
> >>> +
> >>> +&cec {
> >>> + status = "okay";
> >>> +};
> >>> +
> >>> +&cpu0 {
> >>> + proc-supply = <&mt6397_vpca15_reg>;
> >>> +};
> >>> +
> >>> +&cpu1 {
> >>> + proc-supply = <&mt6397_vpca15_reg>;
> >>> +};
> >>> +
> >>> +&cpu2 {
> >>> + proc-supply = <&da9211_vcpu_reg>;
> >>> + sram-supply = <&mt6397_vsramca7_reg>;
> >>> +};
> >>> +
> >>> +&cpu3 {
> >>> + proc-supply = <&da9211_vcpu_reg>;
> >>> + sram-supply = <&mt6397_vsramca7_reg>;
> >>> +};
> >>> +
> >>> +&cpu_thermal {
> >>> + sustainable-power = <4500>; /* milliwatts */
> >>> + trips {
> >>> + threshold: trip-point@0 {
> >>> + temperature = <60000>;
> >>> + };
> >>> +
> >>> + target: trip-point@1 {
> >>> + temperature = <65000>;
> >>> + };
> >>> + };
> >>> +};
> >>> +
> >>> +&dsi0 {
> >>> + status = "okay";
> >>> + ports {
> >>> + #address-cells = <1>;
> >>> + #size-cells = <0>;
> >>> +
> >>> + port@1 {
> >>> + dsi0_out: endpoint {
> >>> + remote-endpoint = <&ps8640_in>;
> >>> + };
> >>> + };
> >>> + };
> >>> +};
> >>> +
> >>> +&dpi0 {
> >>> + status = "okay";
> >>> +};
> >>> +
> >>> +&hdmi0 {
> >>> + status = "okay";
> >>> + ports {
> >>> + port@1 {
> >>> + reg = <1>;
> >>> +
> >>> + hdmi0_out: endpoint {
> >>> + remote-endpoint = <&hdmi_connector_in>;
> >>> + };
> >>> + };
> >>> + };
> >>> +};
> >>> +
> >>> +&hdmi_phy {
> >>> + status = "okay";
> >>> + mediatek,ibias = <0xc>;
> >>> +};
> >>> +
> >>> +&i2c0 {
> >>> + status = "okay";
> >>> +
> >>> + rt5650: audio-codec@1a {
> >>> + compatible = "realtek,rt5650";
> >>> + reg = <0x1a>;
> >>> + avdd-supply = <&mt6397_vgp1_reg>;
> >>> + cpvdd-supply = <&mt6397_vcama_reg>;
> >>
> >> Hm, only defined for "realtek,rt5663", I suppose that's an inconsistency in the
> >> binding documentation. Can you please double check?
> >>
> > This one? https://github.com/torvalds/linux/blob/master/sound/soc/codecs/rt5645.c#L3582
> >
>
> Yes, I checked myself and send a patch to fix the binding description, which was
> missing the two suppliers.
>
>
> >>> + interrupt-parent = <&pio>;
> >>> + interrupts = <3 IRQ_TYPE_EDGE_BOTH>;
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 = <&rt5650_irq>;
> >>> + #sound-dai-cells = <1>;
> >>> + realtek,dmic1-data-pin = <2>;
> >>> + realtek,jd-mode = <2>;
> >>> + };
> >>> +
> >>> + ps8640: edp-bridge@8 {
> >>> + compatible = "parade,ps8640";
> >>> + reg = <0x8>;
> >>> + powerdown-gpios = <&pio 127 GPIO_ACTIVE_LOW>;
> >>> + reset-gpios = <&pio 115 GPIO_ACTIVE_LOW>;
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 = <&ps8640_pins>;
> >>> + vdd12-supply = <&ps8640_fixed_1v2>;
> >>> + vdd33-supply = <&mt6397_vgp2_reg>;
> >>> +
> >>> + ports {
> >>> + #address-cells = <1>;
> >>> + #size-cells = <0>;
> >>> +
> >>> + port@0 {
> >>> + reg = <0>;
> >>> +
> >>> + ps8640_in: endpoint {
> >>> + remote-endpoint = <&dsi0_out>;
> >>> + };
> >>> + };
> >>> +
> >>> + port@1 {
> >>> + reg = <1>;
> >>> +
> >>> + ps8640_out: endpoint {
> >>> + remote-endpoint = <&panel_in>;
> >>> + };
> >>> + };
> >>> + };
> >>> + };
> >>> +};
> >>> +
> >>> +&i2c1 {
> >>> + clock-frequency = <1500000>;
> >>> + status = "okay";
> >>> +
> >>> + da9211: da9211@68 {
> >>> + compatible = "dlg,da9211";
> >>> + reg = <0x68>;
> >>> +
> >>
> >> no interrupts? binding description have this stated as required. what happens
> >> when the device raises an interrupt?
> > Will double check on schematic and add it.
> >>
> >>> + regulators {
> >>> + da9211_vcpu_reg: BUCKA {
> >>> + regulator-name = "VBUCKA";
> >>> + regulator-min-microvolt = < 700000>;
> >>> + regulator-max-microvolt = <1310000>;
> >>> + regulator-min-microamp = <2000000>;
> >>> + regulator-max-microamp = <4400000>;
> >>> + regulator-ramp-delay = <10000>;
> >>> + regulator-always-on;
> >>> + regulator-allowed-modes = <0 1>;
> >>> + };
> >>> +
> >>> + da9211_vgpu_reg: BUCKB {
> >>> + regulator-name = "VBUCKB";
> >>> + regulator-min-microvolt = < 700000>;
> >>> + regulator-max-microvolt = <1310000>;
> >>> + regulator-min-microamp = <2000000>;
> >>> + regulator-max-microamp = <3000000>;
> >>> + regulator-ramp-delay = <10000>;
> >>> + };
> >>> + };
> >>> + };
> >>> +};
> >>> +
> >>> +&i2c2 {
> >>> + status = "okay";
> >>> +
> >>> + tpm: tpm@20 {
> >>> + compatible = "infineon,slb9645tt";
> >>> + reg = <0x20>;
> >>> + powered-while-suspended;
> >>> + };
> >>> +};
> >>> +
> >>> +&i2c3 {
> >>> + clock-frequency = <400000>;
> >>> + status = "okay";
> >>> +
> >>> + touchscreen: touchscreen@10 {
> >>> + compatible = "elan,ekth3500";
> >>> + reg = <0x10>;
> >>> + interrupt-parent = <&pio>;
> >>> + interrupts = <88 IRQ_TYPE_LEVEL_LOW>;
> >>> + };
> >>> +};
> >>> +
> >>> +&i2c4 {
> >>> + clock-frequency = <400000>;
> >>> + status = "okay";
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 = <&trackpad_irq>;
> >>
> >> Why not move the pinctrl properties into the trackpad node?
> >>
> > As second source trackpad device and original device shares same
> > compatible string (rev id), we need to add 2nd trackpad node here.
> > According to previous log (since I don't have a second source trackpad
> > device to test), adding pinctrl in each trackpad node, there would be
> > error:
> > [ 0.643501] mediatek-mt8173-pinctrl 1000b000.pinctrl: pin URXD3
> > already requested by 7-0015; cannot claim for 7-002c
> > [ 0.643525] mediatek-mt8173-pinctrl 1000b000.pinctrl: pin-117
> > (7-002c) status -22
> > [ 0.643548] mediatek-mt8173-pinctrl 1000b000.pinctrl: could not
> > request pin 117 (URXD3) from group URXD3 on device 1000b000.pinctrl
> > [ 0.643568] i2c_hid 7-002c: Error applying setting, reverse things back
> > [ 0.643867] i2c 7-002c: Driver i2c_hid requests probe deferral
> >
> >
>
> I think we can fix this, if we create the aforementioned two board DTS files.
> Correct?
>
> >>> +
> >>> + trackpad: trackpad@15 {
> >>> + compatible = "elan,ekth3000";
> >>> + interrupt-parent = <&pio>;
> >>> + interrupts = <117 IRQ_TYPE_LEVEL_LOW>;
> >>> + reg = <0x15>;
> >>> + vcc-supply = <&mt6397_vgp6_reg>;
> >>> + wakeup-source;
> >>> + };
> >>> +};
> >>> +
> >>> +&mipi_tx0 {
> >>> + status = "okay";
> >>> +};
> >>> +
> >>> +&mmc0 {
> >>> + status = "okay";
> >>> + pinctrl-names = "default", "state_uhs";
> >>> + pinctrl-0 = <&mmc0_pins_default>;
> >>> + pinctrl-1 = <&mmc0_pins_uhs>;
> >>> + bus-width = <8>;
> >>> + max-frequency = <200000000>;
> >>> + cap-mmc-highspeed;
> >>> + mmc-hs200-1_8v;
> >>> + mmc-hs400-1_8v;
> >>> + cap-mmc-hw-reset;
> >>> + hs400-ds-delay = <0x14015>;
> >>> + mediatek,hs200-cmd-int-delay=<30>;
> >>> + mediatek,hs400-cmd-int-delay=<14>;
> >>> + mediatek,hs400-cmd-resp-sel-rising;
> >>> + vmmc-supply = <&mt6397_vemc_3v3_reg>;
> >>> + vqmmc-supply = <&mt6397_vio18_reg>;
> >>> + assigned-clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>;
> >>> + assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL_D2>;
> >>> + non-removable;
> >>> +};
> >>> +
> >>> +&mmc1 {
> >>> + status = "okay";
> >>> + pinctrl-names = "default", "state_uhs";
> >>> + pinctrl-0 = <&mmc1_pins_default>;
> >>> + pinctrl-1 = <&mmc1_pins_uhs>;
> >>> + bus-width = <4>;
> >>> + max-frequency = <200000000>;
> >>> + cap-sd-highspeed;
> >>> + sd-uhs-sdr50;
> >>> + sd-uhs-sdr104;
> >>> + cd-gpios = <&pio 1 GPIO_ACTIVE_HIGH>;
> >>> + vmmc-supply = <&mt6397_vmch_reg>;
> >>> + vqmmc-supply = <&mt6397_vmc_reg>;
> >>> +};
> >>> +
> >>> +&mmc3 {
> >>> + status = "okay";
> >>> + pinctrl-names = "default", "state_uhs";
> >>> + pinctrl-0 = <&mmc3_pins_default>;
> >>> + pinctrl-1 = <&mmc3_pins_uhs>;
> >>> + bus-width = <4>;
> >>> + max-frequency = <200000000>;
> >>> + cap-sd-highspeed;
> >>> + sd-uhs-sdr50;
> >>> + sd-uhs-sdr104;
> >>> + sdr104-clk-delay = <5>;
> >>
> >> Not an upstream property, please delete it.
> >>
> >>> + keep-power-in-suspend;
> >>> + enable-sdio-wakeup;
> >>> + cap-sdio-irq;
> >>> + vmmc-supply = <&sdio_fixed_3v3>;
> >>> + vqmmc-supply = <&mt6397_vgp3_reg>;
> >>> + non-removable;
> >>> + cap-power-off-card;
> >>> +
> >>> + #address-cells = <1>;
> >>> + #size-cells = <0>;
> >>> +
> >>> + btmrvl: btmrvl@2 {
> >>> + compatible = "marvell,sd8897-bt";
> >>> + reg = <2>;
> >>> + interrupt-parent = <&pio>;
> >>> + interrupts = <119 IRQ_TYPE_LEVEL_LOW>;
> >>> + marvell,wakeup-pin = /bits/ 16 <0x0d>;
> >>> + marvell,wakeup-gap-ms = /bits/ 16 <0x64>;
> >>> + };
> >>> +
> >>> + mwifiex: mwifiex@1 {
> >>> + compatible = "marvell,sd8897";
> >>> + reg = <1>;
> >>> + interrupt-parent = <&pio>;
> >>> + interrupts = <38 IRQ_TYPE_LEVEL_LOW>;
> >>> + marvell,wakeup-pin = <3>;
> >>> + marvell,caldata_ed_mac = /bits/ 8 <
> >>> +0x01 0x00 0x07 0x00 0x14 0x00 0x01 0x00 0x00 0x00 0x12 0x00 0x02 0x00 0x01 0x00
> >>> +0x01 0x00 0x00 0x00 0x12 0x00 0x02 0x00 0x01 0x00
> >>> + >;
> >>
> >> Not an upstream property, please delete.
> >>
> >>> + };
> >>> +};
> >>> +
> >>> +&nor_flash {
> >>> + status = "okay";
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 = <&nor_gpio1_pins>;
> >>> + bus-width = <8>;
> >>> + max-frequency = <50000000>;
> >>> + non-removable;
> >>> + flash@0 {
> >>> + compatible = "jedec,spi-nor";
> >>> + reg = <0>;
> >>> + };
> >>> +};
> >>> +
> >>> +&pio {
> >>> + aud_i2s2: aud_i2s2 {
> >>> + pins1 {
> >>> + pinmux = <MT8173_PIN_128_I2S0_LRCK__FUNC_I2S1_WS>,
> >>> + <MT8173_PIN_129_I2S0_BCK__FUNC_I2S1_BCK>,
> >>> + <MT8173_PIN_130_I2S0_MCK__FUNC_I2S1_MCK>,
> >>> + <MT8173_PIN_131_I2S0_DATA0__FUNC_I2S1_DO_1>,
> >>> + <MT8173_PIN_12_EINT12__FUNC_I2S2_WS>,
> >>> + <MT8173_PIN_13_EINT13__FUNC_I2S2_BCK>,
> >>> + <MT8173_PIN_132_I2S0_DATA1__FUNC_I2S2_DI_2>;
> >>> + bias-pull-down;
> >>> + };
> >>> + };
> >>> +
> >>> + bl_fixed_pins: bl_fixed_pins {
> >>> + pins1 {
> >>> + pinmux = <MT8173_PIN_32_UTXD2__FUNC_GPIO32>;
> >>> + output-low;
> >>> + };
> >>> + };
> >>> +
> >>> + bt_wake_pins: bt_wake_pins {
> >>> + pins1 {
> >>> + pinmux = <MT8173_PIN_119_KPROW0__FUNC_GPIO119>;
> >>> + bias-pull-up;
> >>> + };
> >>> + };
> >>> +
> >>> + disp_pwm0_pins: disp_pwm0_pins {
> >>> + pins1 {
> >>> + pinmux = <MT8173_PIN_87_DISP_PWM0__FUNC_DISP_PWM0>;
> >>> + output-low;
> >>> + };
> >>> + };
> >>> +
> >>> + gpio_keys_pins: gpio_keys_pins {
> >>> + volume_pins {
> >>> + pinmux = <MT8173_PIN_123_KPCOL1__FUNC_GPIO123>,
> >>> + <MT8173_PIN_124_KPCOL2__FUNC_GPIO124>;
> >>> + bias-pull-up;
> >>> + };
> >>> +
> >>> + tablet_mode_pins {
> >>> + pinmux = <MT8173_PIN_121_KPROW2__FUNC_GPIO121>;
> >>> + bias-pull-up;
> >>> + };
> >>> + };
> >>> +
> >>> + hdmi_mux_pins: hdmi_mux_pins {
> >>> + pins1 {
> >>> + pinmux = <MT8173_PIN_36_DAISYNC__FUNC_GPIO36>;
> >>> + };
> >>> + };
> >>> +
> >>> + mmc0_pins_default: mmc0default {
> >>> + pins_cmd_dat {
> >>> + pinmux = <MT8173_PIN_57_MSDC0_DAT0__FUNC_MSDC0_DAT0>,
> >>> + <MT8173_PIN_58_MSDC0_DAT1__FUNC_MSDC0_DAT1>,
> >>> + <MT8173_PIN_59_MSDC0_DAT2__FUNC_MSDC0_DAT2>,
> >>> + <MT8173_PIN_60_MSDC0_DAT3__FUNC_MSDC0_DAT3>,
> >>> + <MT8173_PIN_61_MSDC0_DAT4__FUNC_MSDC0_DAT4>,
> >>> + <MT8173_PIN_62_MSDC0_DAT5__FUNC_MSDC0_DAT5>,
> >>> + <MT8173_PIN_63_MSDC0_DAT6__FUNC_MSDC0_DAT6>,
> >>> + <MT8173_PIN_64_MSDC0_DAT7__FUNC_MSDC0_DAT7>,
> >>> + <MT8173_PIN_66_MSDC0_CMD__FUNC_MSDC0_CMD>;
> >>> + bias-pull-up;
> >>> + };
> >>> +
> >>> + pins_clk {
> >>> + pinmux = <MT8173_PIN_65_MSDC0_CLK__FUNC_MSDC0_CLK>;
> >>> + bias-pull-down;
> >>
> >> identation.
> >>
> >>> + };
> >>> +
> >>> + pins_rst {
> >>> + pinmux = <MT8173_PIN_68_MSDC0_RST___FUNC_MSDC0_RSTB>;
> >>> + bias-pull-up;
> >>> + };
> >>> + };
> >>> +
> >>> + mmc1_pins_default: mmc1default {
> >>> + pins_cmd_dat {
> >>> + pinmux = <MT8173_PIN_73_MSDC1_DAT0__FUNC_MSDC1_DAT0>,
> >>> + <MT8173_PIN_74_MSDC1_DAT1__FUNC_MSDC1_DAT1>,
> >>> + <MT8173_PIN_75_MSDC1_DAT2__FUNC_MSDC1_DAT2>,
> >>> + <MT8173_PIN_76_MSDC1_DAT3__FUNC_MSDC1_DAT3>,
> >>> + <MT8173_PIN_78_MSDC1_CMD__FUNC_MSDC1_CMD>;
> >>> + input-enable;
> >>> + drive-strength = <MTK_DRIVE_4mA>;
> >>> + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
> >>> + };
> >>> +
> >>> + pins_clk {
> >>> + pinmux = <MT8173_PIN_77_MSDC1_CLK__FUNC_MSDC1_CLK>;
> >>> + bias-pull-down;
> >>> + drive-strength = <MTK_DRIVE_4mA>;
> >>> + };
> >>> +
> >>> + pins_insert {
> >>> + pinmux = <MT8173_PIN_1_EINT1__FUNC_GPIO1>;
> >>> + bias-pull-up;
> >>> + };
> >>> + };
> >>> +
> >>> + mmc3_pins_default: mmc3default {
> >>> + pins_dat {
> >>> + pinmux = <MT8173_PIN_22_MSDC3_DAT0__FUNC_MSDC3_DAT0>,
> >>> + <MT8173_PIN_23_MSDC3_DAT1__FUNC_MSDC3_DAT1>,
> >>> + <MT8173_PIN_24_MSDC3_DAT2__FUNC_MSDC3_DAT2>,
> >>> + <MT8173_PIN_25_MSDC3_DAT3__FUNC_MSDC3_DAT3>;
> >>> + input-enable;
> >>> + drive-strength = <MTK_DRIVE_8mA>;
> >>> + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
> >>> + };
> >>> +
> >>> + pins_cmd {
> >>> + pinmux = <MT8173_PIN_27_MSDC3_CMD__FUNC_MSDC3_CMD>;
> >>> + input-enable;
> >>> + drive-strength = <MTK_DRIVE_8mA>;
> >>> + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
> >>> + };
> >>> +
> >>> + pins_clk {
> >>> + pinmux = <MT8173_PIN_26_MSDC3_CLK__FUNC_MSDC3_CLK>;
> >>> + bias-pull-down;
> >>> + drive-strength = <MTK_DRIVE_8mA>;
> >>> + };
> >>> +
> >>> + pins_pdn {
> >>> + pinmux = <MT8173_PIN_85_AUD_DAT_MOSI__FUNC_GPIO85>;
> >>> + output-low;
> >>> + };
> >>> + };
> >>> +
> >>> + mmc0_pins_uhs: mmc0 {
> >>> + pins_cmd_dat {
> >>> + pinmux = <MT8173_PIN_57_MSDC0_DAT0__FUNC_MSDC0_DAT0>,
> >>> + <MT8173_PIN_58_MSDC0_DAT1__FUNC_MSDC0_DAT1>,
> >>> + <MT8173_PIN_59_MSDC0_DAT2__FUNC_MSDC0_DAT2>,
> >>> + <MT8173_PIN_60_MSDC0_DAT3__FUNC_MSDC0_DAT3>,
> >>> + <MT8173_PIN_61_MSDC0_DAT4__FUNC_MSDC0_DAT4>,
> >>> + <MT8173_PIN_62_MSDC0_DAT5__FUNC_MSDC0_DAT5>,
> >>> + <MT8173_PIN_63_MSDC0_DAT6__FUNC_MSDC0_DAT6>,
> >>> + <MT8173_PIN_64_MSDC0_DAT7__FUNC_MSDC0_DAT7>,
> >>> + <MT8173_PIN_66_MSDC0_CMD__FUNC_MSDC0_CMD>;
> >>> + input-enable;
> >>> + drive-strength = <MTK_DRIVE_6mA>;
> >>> + bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
> >>> + };
> >>> +
> >>> + pins_clk {
> >>> + pinmux = <MT8173_PIN_65_MSDC0_CLK__FUNC_MSDC0_CLK>;
> >>> + drive-strength = <MTK_DRIVE_6mA>;
> >>> + bias-pull-down = <MTK_PUPD_SET_R1R0_01>;
> >>> + };
> >>> +
> >>> + pins_ds {
> >>> + pinmux = <MT8173_PIN_67_MSDC0_DSL__FUNC_MSDC0_DSL>;
> >>> + drive-strength = <MTK_DRIVE_10mA>;
> >>> + bias-pull-down = <MTK_PUPD_SET_R1R0_01>;
> >>> + };
> >>> +
> >>> + pins_rst {
> >>> + pinmux = <MT8173_PIN_68_MSDC0_RST___FUNC_MSDC0_RSTB>;
> >>> + bias-pull-up;
> >>> + };
> >>> + };
> >>> +
> >>> + mmc1_pins_uhs: mmc1 {
> >>> + pins_cmd_dat {
> >>> + pinmux = <MT8173_PIN_73_MSDC1_DAT0__FUNC_MSDC1_DAT0>,
> >>> + <MT8173_PIN_74_MSDC1_DAT1__FUNC_MSDC1_DAT1>,
> >>> + <MT8173_PIN_75_MSDC1_DAT2__FUNC_MSDC1_DAT2>,
> >>> + <MT8173_PIN_76_MSDC1_DAT3__FUNC_MSDC1_DAT3>,
> >>> + <MT8173_PIN_78_MSDC1_CMD__FUNC_MSDC1_CMD>;
> >>> + input-enable;
> >>> + drive-strength = <MTK_DRIVE_6mA>;
> >>> + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
> >>> + };
> >>> +
> >>> + pins_clk {
> >>> + pinmux = <MT8173_PIN_77_MSDC1_CLK__FUNC_MSDC1_CLK>;
> >>> + drive-strength = <MTK_DRIVE_8mA>;
> >>> + bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
> >>> + };
> >>> + };
> >>> +
> >>> + mmc3_pins_uhs: mmc3 {
> >>> + pins_dat {
> >>> + pinmux = <MT8173_PIN_22_MSDC3_DAT0__FUNC_MSDC3_DAT0>,
> >>> + <MT8173_PIN_23_MSDC3_DAT1__FUNC_MSDC3_DAT1>,
> >>> + <MT8173_PIN_24_MSDC3_DAT2__FUNC_MSDC3_DAT2>,
> >>> + <MT8173_PIN_25_MSDC3_DAT3__FUNC_MSDC3_DAT3>;
> >>> + input-enable;
> >>> + drive-strength = <MTK_DRIVE_8mA>;
> >>> + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
> >>> + };
> >>> +
> >>> + pins_cmd {
> >>> + pinmux = <MT8173_PIN_27_MSDC3_CMD__FUNC_MSDC3_CMD>;
> >>> + input-enable;
> >>> + drive-strength = <MTK_DRIVE_8mA>;
> >>> + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
> >>> + };
> >>> +
> >>> + pins_clk {
> >>> + pinmux = <MT8173_PIN_26_MSDC3_CLK__FUNC_MSDC3_CLK>;
> >>> + drive-strength = <MTK_DRIVE_8mA>;
> >>> + bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
> >>> + };
> >>> + };
> >>> +
> >>> + nor_gpio1_pins: nor {
> >>> + pins1 {
> >>> + pinmux = <MT8173_PIN_6_EINT6__FUNC_SFCS0>,
> >>> + <MT8173_PIN_7_EINT7__FUNC_SFHOLD>,
> >>> + <MT8173_PIN_8_EINT8__FUNC_SFIN>;
> >>> + input-enable;
> >>> + drive-strength = <MTK_DRIVE_4mA>;
> >>> + bias-pull-up;
> >>> + };
> >>> +
> >>> + pins2 {
> >>> + pinmux = <MT8173_PIN_5_EINT5__FUNC_SFOUT>;
> >>> + drive-strength = <MTK_DRIVE_4mA>;
> >>> + bias-pull-up;
> >>> + };
> >>> +
> >>> + pins_clk {
> >>> + pinmux = <MT8173_PIN_9_EINT9__FUNC_SFCK>;
> >>> + input-enable;
> >>> + drive-strength = <MTK_DRIVE_4mA>;
> >>> + bias-pull-up;
> >>> + };
> >>> + };
> >>> +
> >>> + panel_fixed_pins: panel_fixed_pins {
> >>> + pins1 {
> >>> + pinmux = <MT8173_PIN_41_CMMCLK__FUNC_GPIO41>;
> >>> + };
> >>> + };
> >>> +
> >>> + ps8640_pins: ps8640_pins {
> >>> + pins1 {
> >>> + pinmux = <MT8173_PIN_92_PCM_CLK__FUNC_GPIO92>,
> >>> + <MT8173_PIN_115_URTS0__FUNC_GPIO115>,
> >>> + <MT8173_PIN_127_LCM_RST__FUNC_GPIO127>;
> >>> + };
> >>> + };
> >>> +
> >>> + ps8640_fixed_pins: ps8640_fixed_pins {
> >>> + pins1 {
> >>> + pinmux = <MT8173_PIN_30_URTS2__FUNC_GPIO30>;
> >>> + };
> >>> + };
> >>> +
> >>> + rt5650_irq: rt5650_irq {
> >>> + pins1 {
> >>> + pinmux = <MT8173_PIN_3_EINT3__FUNC_GPIO3>;
> >>> + bias-pull-down;
> >>> + };
> >>> + };
> >>> +
> >>> + spi_pins_a: spi1 {
> >>> + pins1 {
> >>> + pinmux = <MT8173_PIN_0_EINT0__FUNC_GPIO0>;
> >>> + bias-pull-up;
> >>> + };
> >>> +
> >>> + pins_spi {
> >>> + pinmux = <MT8173_PIN_102_MSDC2_DAT2__FUNC_SPI_CK_1_>,
> >>> + <MT8173_PIN_103_MSDC2_DAT3__FUNC_SPI_MI_1_>,
> >>> + <MT8173_PIN_104_MSDC2_CLK__FUNC_SPI_MO_1_>,
> >>> + <MT8173_PIN_105_MSDC2_CMD__FUNC_SPI_CS_1_>;
> >>> + bias-disable;
> >>> + };
> >>> + };
> >>> +
> >>> + trackpad_irq: trackpad_irq {
> >>> + pins1 {
> >>> + pinmux = <MT8173_PIN_117_URXD3__FUNC_GPIO117>;
> >>> + input-enable;
> >>> + bias-pull-up;
> >>> + };
> >>> + };
> >>> +
> >>> + usb_pins: usb@0 {
> >>> + pins1 {
> >>> + pinmux = <MT8173_PIN_101_MSDC2_DAT1__FUNC_GPIO101>;
> >>> + output-high;
> >>> + bias-disable;
> >>> + };
> >>> + };
> >>> +
> >>> + wifi_wake_pins: wifi_wake_pins {
> >>> + pins1 {
> >>> + pinmux = <MT8173_PIN_38_CONN_RST__FUNC_GPIO38>;
> >>> + bias-pull-up;
> >>> + };
> >>> + };
> >>> +};
> >>> +
> >>> +&pwm0 {
> >>> + status = "okay";
> >>> +};
> >>> +
> >>> +&pwrap {
> >>> + pmic: mt6397 {
> >>> + compatible = "mediatek,mt6397";
> >>> + #address-cells = <1>;
> >>> + #size-cells = <1>;
> >>> + interrupt-parent = <&pio>;
> >>> + interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
> >>> + interrupt-controller;
> >>> + #interrupt-cells = <2>;
> >>> +
> >>> + mt6397rtc: mt6397rtc {
> >>
> >> AFAIK this should be
> >> rtc: mt6397rtc {
> >>
> >> Please fix that for all subnodes.
> >>
> > Will fix in next version
> >>> + compatible = "mediatek,mt6397-rtc";
> >>> + };
> >>> +
> >>> + syscfg_pctl_pmic: syscfg_pctl_pmic@c000 {
> >>> + compatible = "mediatek,mt6397-pctl-pmic-syscfg",
> >>> + "syscon";
> >>> + reg = <0 0x0000c000 0 0x0108>;
> >>
> >> not an upstream compatible, please delete the node.
> >>
>
> I think my comment was not correct. I'll have to dig more to understand why we
> have a compatible without a binding description.
>
> Regards,
> Matthias
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH v2 2/2] arm64: dts: mediatek: add mt8173 elm and hana board
2020-01-14 15:10 ` Matthias Brugger
2020-01-14 15:33 ` Hsin-Yi Wang
@ 2020-01-15 8:53 ` Hsin-Yi Wang
2020-01-15 16:14 ` Matthias Brugger
1 sibling, 1 reply; 14+ messages in thread
From: Hsin-Yi Wang @ 2020-01-15 8:53 UTC (permalink / raw)
To: Matthias Brugger
Cc: Mark Rutland, Devicetree List, Nicolas Boichat, lkml,
Daniel Kurtz, Rob Herring, linux-mediatek,
Enric Balletbo i Serra,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE
On Tue, Jan 14, 2020 at 11:10 PM Matthias Brugger
<matthias.bgg@gmail.com> wrote:
>
>
>
> On 13/01/2020 19:01, Hsin-Yi Wang wrote:
> > On Fri, Jan 10, 2020 at 9:42 PM Matthias Brugger <matthias.bgg@gmail.com> wrote:
> >>
> >>
> > Thanks, I will address the comments and send next version
> >>
> >> On 10/01/2020 08:37, Hsin-Yi Wang wrote:
> >>> Elm is Acer Chromebook R13. Hana is Lenovo Chromebook. Both uses mt8173
> >>> SoC.
> >>>
> >>> Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
> >>> ---
> >>> Changes in v2:
> >>> - remove downstream nodes and unused nodes
> >>> - use GPIO_ACTIVE_LOW for ps8640 gpios
> >>> - move trackpad to hana
> >>> ---
> >>> arch/arm64/boot/dts/mediatek/Makefile | 3 +
> >>> .../dts/mediatek/mt8173-elm-hana-rev7.dts | 27 +
> >>> .../boot/dts/mediatek/mt8173-elm-hana.dts | 16 +
> >>> .../boot/dts/mediatek/mt8173-elm-hana.dtsi | 60 +
> >>> arch/arm64/boot/dts/mediatek/mt8173-elm.dts | 15 +
> >>> arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi | 1040 +++++++++++++++++
> >>> 6 files changed, 1161 insertions(+)
> >>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts
> >>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts
> >>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dtsi
> >>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm.dts
> >>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi
> >>>
> >>> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> >>> index 458bbc422a94..b45a45a565a1 100644
> >>> --- a/arch/arm64/boot/dts/mediatek/Makefile
> >>> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> >>> @@ -6,5 +6,8 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb
> >>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
> >>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
> >>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
> >>> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm.dtb
> >>> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana.dtb
> >>> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana-rev7.dtb
> >>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-evb.dtb
> >>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-evb.dtb
> >>> diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts
> >>> new file mode 100644
> >>> index 000000000000..a3616bc3d859
> >>> --- /dev/null
> >>> +++ b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts
> >>> @@ -0,0 +1,27 @@
> >>> +// SPDX-License-Identifier: GPL-2.0-only
> >>> +/*
> >>> + * Copyright 2019 MediaTek Inc.
> >>> + */
> >>> +
> >>> +/dts-v1/;
> >>> +#include "mt8173-elm-hana.dtsi"
> >>> +
> >>> +/ {
> >>> + model = "Mediatek Hana rev7 board";
> >>> + compatible = "google,hana-rev7", "mediatek,mt8173";
> >>> +};
> >>> +
> >>> +&cpu_thermal {
> >>> + trips {
> >>> + cpu_crit: cpu_crit@0 {
> >>> + temperature = <100000>;
> >>> + type = "critical";
> >>> + };
> >>> + };
> >>> +};
> >>> +
> >>> +&gpio_keys {
> >>> + /delete-node/tablet_mode;
> >>> + /delete-node/volume_down;
> >>> + /delete-node/volume_up;
> >>> +};
> >>> \ No newline at end of file
> >>> diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts
> >>> new file mode 100644
> >>> index 000000000000..8cbcc75192e3
> >>> --- /dev/null
> >>> +++ b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts
> >>> @@ -0,0 +1,16 @@
> >>> +// SPDX-License-Identifier: GPL-2.0-only
> >>> +/*
> >>> + * Copyright 2016 MediaTek Inc.
> >>> + */
> >>> +
> >>> +/dts-v1/;
> >>> +#include "mt8173-elm-hana.dtsi"
> >>> +
> >>> +/ {
> >>> + model = "Mediatek Hana rev0 board";
>
> If we can't make this more verbose, at least delete rev0, that's confusing.
> Should the name not be "Google Hana"?
>
> >>> + compatible = "google,hana-rev6",
> >>> + "google,hana-rev5", "google,hana-rev4",
> >>> + "google,hana-rev3", "google,hana-rev2",
> >>> + "google,hana-rev1", "google,hana-rev0",
> >>> + "google,hana", "mediatek,mt8173";
> >>> +};
> >>
> >> I'm a bit confused about all this versions. Do you want to keep them for
> >> internal use, as I suppose only rev6 is available to the general public,
> >> correct? I'm fine with keeping the old revisions if that's of use for you,
> >> otherwise I'd prefer to delete them.
> > According to internal feedback system, at least rev3, rev6, rev7 are
> > in general public. I can delete rev0~rev2, since they are earlier
> > version device.
>
> If you don't plan to use the rev0 to rev2 in-house, then we can delete them.
>
> >>
> >> Model name could be more verbose.
> >>
> >>> \ No newline at end of file
> >>> diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dtsi b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dtsi
> >>> new file mode 100644
> >>> index 000000000000..35e12b290947
> >>> --- /dev/null
> >>> +++ b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dtsi
> >>> @@ -0,0 +1,60 @@
> >>> +// SPDX-License-Identifier: GPL-2.0-only
> >>> +/*
> >>> + * Copyright 2016 MediaTek Inc.
> >>> + */
> >>> +
> >>> +#include "mt8173-elm.dtsi"
> >>> +
> >>> +&i2c0 {
> >>> + clock-frequency = <200000>;
> >>> +};
> >>> +
> >>> +&i2c3 {
> >>> + touchscreen2: touchscreen@34 {
> >>> + compatible = "melfas,mip4_ts";
> >>> + reg = <0x34>;
> >>> + interrupt-parent = <&pio>;
> >>> + interrupts = <88 IRQ_TYPE_LEVEL_LOW>;
> >>> + };
> >>> +
> >>> + touchscreen3: touchscreen@20 {
> >>> + compatible = "hid-over-i2c";
> >>> + reg = <0x20>;
> >>> + hid-descr-addr = <0x0020>;
> >>> + interrupt-parent = <&pio>;
> >>> + interrupts = <88 IRQ_TYPE_LEVEL_LOW>;
> >>> + };
> >>
> >> In v1 you mentioned:
> >> "Partners wants to increase touchpad and touchscreen source (they choose
> >> synaptics) for hana 300e, and synaptics uses hid-over-i2c driver."
> >>
> >> So the partner uses the same compatible (google,hana-rev6?) for both devices?
> >>
> > Confirmed with others, second source devices share same compatible.
>
> We should create independent dts for the different boards. Like it is done for
> gru-scarlett. Doesn't the FW provide the sku number in the compatible string?
>
> >>> +};
> >>> +
> >>> +&i2c4 {
> >>> + trackpad2: trackpad@2c {
> >>> + compatible = "hid-over-i2c";
> >>> + interrupt-parent = <&pio>;
> >>> + interrupts = <117 IRQ_TYPE_LEVEL_LOW>;
> >>> + reg = <0x2c>;
> >>> + hid-descr-addr = <0x0020>;
> >>> + wakeup-source;
> >>> + };
> >>> +};
> >>> +
> >>> +&mmc1 {
> >>> + wp-gpios = <&pio 42 GPIO_ACTIVE_HIGH>;
> >>> +};
> >>> +
> >>> +&pio {
> >>> + hdmi_mux_pins: hdmi_mux_pins {
> >>> + pins2 {
> >>> + pinmux = <MT8173_PIN_98_URTS1__FUNC_GPIO98>;
> >>> + bias-pull-up;
> >>> + output-high;
> >>> + };
> >>> + };
> >>> +
> >>> + mmc1_pins_default: mmc1default {
> >>> + pins_wp {
> >>> + pinmux = <MT8173_PIN_42_DSI_TE__FUNC_GPIO42>;
> >>> + input-enable;
> >>> + bias-pull-up;
> >>> + };
> >>> + };
> >>> +};
> >>> \ No newline at end of file
> >>> diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm.dts b/arch/arm64/boot/dts/mediatek/mt8173-elm.dts
> >>> new file mode 100644
> >>> index 000000000000..e5da2355760e
> >>> --- /dev/null
> >>> +++ b/arch/arm64/boot/dts/mediatek/mt8173-elm.dts
> >>> @@ -0,0 +1,15 @@
> >>> +// SPDX-License-Identifier: GPL-2.0-only
> >>> +/*
> >>> + * Copyright 2016 MediaTek Inc.
> >>> + */
> >>> +
> >>> +/dts-v1/;
> >>> +#include "mt8173-elm.dtsi"
> >>> +
> >>> +/ {
> >>> + model = "Mediatek Elm board";
> >>> + compatible = "google,elm-rev8", "google,elm-rev7", "google,elm-rev6",
> >>> + "google,elm-rev5", "google,elm-rev4", "google,elm-rev3",
> >>> + "google,elm-rev2", "google,elm-rev1",
> >>> + "google,elm", "mediatek,mt8173";
> >>> +};
> >>> \ No newline at end of file
> >>> diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi b/arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi
> >>> new file mode 100644
> >>> index 000000000000..2ac738bebe04
> >>> --- /dev/null
> >>> +++ b/arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi
> >>> @@ -0,0 +1,1040 @@
> >>> +// SPDX-License-Identifier: GPL-2.0-only
> >>> +/*
> >>> + * Copyright 2016 MediaTek Inc.
> >>> + */
> >>> +
> >>> +#include <dt-bindings/input/input.h>
> >>> +#include <dt-bindings/gpio/gpio.h>
> >>> +#include "mt8173.dtsi"
> >>> +
> >>> +/ {
> >>> + aliases {
> >>> + serial0 = &uart0;
> >>> + serial1 = &uart1;
> >>> + serial2 = &uart2;
> >>> + serial3 = &uart3;
> >>> + };
> >>> +
> >>> + memory@40000000 {
> >>> + device_type = "memory";
> >>> + reg = <0 0x40000000 0 0x80000000>;
> >>> + };
> >>> +
> >>> + backlight_lcd: backlight_lcd {
> >>> + compatible = "pwm-backlight";
> >>> + pwms = <&pwm0 0 1000000>;
> >>> + brightness-levels = <
> >>> + 0 16 32 48 64 80 96 112
> >>> + 128 144 160 176 192 208 224 240
> >>> + 255
> >>> + >;
> >>> + default-brightness-level = <9>;
> >>> + power-supply = <&bl_fixed_reg>;
> >>> + enable-gpios = <&pio 95 GPIO_ACTIVE_HIGH>;
> >>> +
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 = <&disp_pwm0_pins>;
> >>> + status = "okay";
> >>> + };
> >>> +
> >>> + bl_fixed_reg: fixedregulator@2 {
> >>> + compatible = "regulator-fixed";
> >>> + regulator-name = "bl_fixed";
> >>> + regulator-min-microvolt = <1800000>;
> >>> + regulator-max-microvolt = <1800000>;
> >>> + startup-delay-us = <1000>;
> >>> + enable-active-high;
> >>> + gpio = <&pio 32 GPIO_ACTIVE_HIGH>;
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 = <&bl_fixed_pins>;
> >>> + };
> >>> +
> >>> + chosen {
> >>> + stdout-path = &uart0;
> >>> + };
> >>> +
> >>> + gpio_keys: gpio-keys {
> >>> + compatible = "gpio-keys";
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 = <&gpio_keys_pins>;
> >>> +
> >>> + lid {
> >>> + label = "Lid";
> >>> + gpios = <&pio 69 GPIO_ACTIVE_LOW>;
> >>> + linux,code = <0>; /* SW_LID */
> >>> + linux,input-type = <5>; /* EV_SW */
> >>> + gpio-key,wakeup;
> >>> + };
> >>> +
> >>> + power {
> >>> + label = "Power";
> >>> + gpios = <&pio 14 GPIO_ACTIVE_HIGH>;
> >>> + linux,code = <KEY_POWER>;
> >>> + debounce-interval = <30>;
> >>> + gpio-key,wakeup;
> >>> + };
> >>> +
> >>> + tablet_mode {
> >>> + label = "Tablet_mode";
> >>> + gpios = <&pio 121 GPIO_ACTIVE_HIGH>;
> >>> + linux,code = <1>; /* SW_TABLET_MODE */
> >>
> >> can't we use SW_TABLET_MODE fomr linux-event-codes.h?
> >>
> > Will fix this.
> >>> + linux,input-type = <5>; /* EV_SW */
> >>
> >> same here.
> >>
> >>> + gpio-key,wakeup;
> >>> + };
> >>> +
> >>> + volume_down {
> >>> + label = "Volume_down";
> >>> + gpios = <&pio 123 GPIO_ACTIVE_LOW>;
> >>> + linux,code = <KEY_VOLUMEDOWN>;
> >>> + };
> >>> +
> >>> + volume_up {
> >>> + label = "Volume_up";
> >>> + gpios = <&pio 124 GPIO_ACTIVE_LOW>;
> >>> + linux,code = <KEY_VOLUMEUP>;
> >>> + };
> >>> + };
> >>> +
> >>> + panel: panel {
> >>> + compatible = "lg,lp120up1";
> >>> + power-supply = <&panel_fixed_3v3>;
> >>> + ddc-i2c-bus = <&i2c0>;
> >>> + backlight = <&backlight_lcd>;
> >>> +
> >>> + port {
> >>> + panel_in: endpoint {
> >>> + remote-endpoint = <&ps8640_out>;
> >>> + };
> >>> + };
> >>> + };
> >>> +
> >>> + panel_fixed_3v3: regulator@1 {
> >>> + compatible = "regulator-fixed";
> >>> + regulator-name = "PANEL_3V3";
> >>> + regulator-min-microvolt = <3300000>;
> >>> + regulator-max-microvolt = <3300000>;
> >>> + enable-active-high;
> >>> + gpio = <&pio 41 GPIO_ACTIVE_HIGH>;
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 = <&panel_fixed_pins>;
> >>> + };
> >>> +
> >>> + ps8640_fixed_1v2: regulator@2 {
> >>> + compatible = "regulator-fixed";
> >>> + regulator-name = "PS8640_1V2";
> >>> + regulator-min-microvolt = <1200000>;
> >>> + regulator-max-microvolt = <1200000>;
> >>> + regulator-enable-ramp-delay = <2000>;
> >>> + enable-active-high;
> >>> + regulator-boot-on;
> >>> + gpio = <&pio 30 GPIO_ACTIVE_HIGH>;
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 = <&ps8640_fixed_pins>;
> >>> + };
> >>> +
> >>> + sdio_fixed_3v3: fixedregulator@0 {
> >>> + compatible = "regulator-fixed";
> >>> + regulator-name = "3V3";
> >>> + regulator-min-microvolt = <3300000>;
> >>> + regulator-max-microvolt = <3300000>;
> >>> + gpio = <&pio 85 GPIO_ACTIVE_HIGH>;
> >>
> >> we don't need to set the pincontroller mux here?
> >>
> > Will double check on schematic and add it.
> >>> + };
> >>> +
> >>> + sound: sound {
> >>> + compatible = "mediatek,mt8173-rt5650";
> >>> + mediatek,audio-codec = <&rt5650 &hdmi0>;
> >>> + mediatek,platform = <&afe>;
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 = <&aud_i2s2>;
> >>> +
> >>> + mediatek,mclk = <1>;
> >>> + codec-capture {
> >>> + sound-dai = <&rt5650 1>;
> >>> + };
> >>> + };
> >>> +
> >>> + hdmicon: connector {
> >>> + compatible = "hdmi-connector";
> >>> + label = "hdmi";
> >>> + type = "a";
> >>> + ddc-i2c-bus = <&hdmiddc0>;
> >>> +
> >>> + port {
> >>> + hdmi_connector_in: endpoint {
> >>> + remote-endpoint = <&hdmi0_out>;
> >>> + };
> >>> + };
> >>> + };
> >>> +};
> >>> +
> >>> +&cec {
> >>> + status = "okay";
> >>> +};
> >>> +
> >>> +&cpu0 {
> >>> + proc-supply = <&mt6397_vpca15_reg>;
> >>> +};
> >>> +
> >>> +&cpu1 {
> >>> + proc-supply = <&mt6397_vpca15_reg>;
> >>> +};
> >>> +
> >>> +&cpu2 {
> >>> + proc-supply = <&da9211_vcpu_reg>;
> >>> + sram-supply = <&mt6397_vsramca7_reg>;
> >>> +};
> >>> +
> >>> +&cpu3 {
> >>> + proc-supply = <&da9211_vcpu_reg>;
> >>> + sram-supply = <&mt6397_vsramca7_reg>;
> >>> +};
> >>> +
> >>> +&cpu_thermal {
> >>> + sustainable-power = <4500>; /* milliwatts */
> >>> + trips {
> >>> + threshold: trip-point@0 {
> >>> + temperature = <60000>;
> >>> + };
> >>> +
> >>> + target: trip-point@1 {
> >>> + temperature = <65000>;
> >>> + };
> >>> + };
> >>> +};
> >>> +
> >>> +&dsi0 {
> >>> + status = "okay";
> >>> + ports {
> >>> + #address-cells = <1>;
> >>> + #size-cells = <0>;
> >>> +
> >>> + port@1 {
> >>> + dsi0_out: endpoint {
> >>> + remote-endpoint = <&ps8640_in>;
> >>> + };
> >>> + };
> >>> + };
> >>> +};
> >>> +
> >>> +&dpi0 {
> >>> + status = "okay";
> >>> +};
> >>> +
> >>> +&hdmi0 {
> >>> + status = "okay";
> >>> + ports {
> >>> + port@1 {
> >>> + reg = <1>;
> >>> +
> >>> + hdmi0_out: endpoint {
> >>> + remote-endpoint = <&hdmi_connector_in>;
> >>> + };
> >>> + };
> >>> + };
> >>> +};
> >>> +
> >>> +&hdmi_phy {
> >>> + status = "okay";
> >>> + mediatek,ibias = <0xc>;
> >>> +};
> >>> +
> >>> +&i2c0 {
> >>> + status = "okay";
> >>> +
> >>> + rt5650: audio-codec@1a {
> >>> + compatible = "realtek,rt5650";
> >>> + reg = <0x1a>;
> >>> + avdd-supply = <&mt6397_vgp1_reg>;
> >>> + cpvdd-supply = <&mt6397_vcama_reg>;
> >>
> >> Hm, only defined for "realtek,rt5663", I suppose that's an inconsistency in the
> >> binding documentation. Can you please double check?
> >>
> > This one? https://github.com/torvalds/linux/blob/master/sound/soc/codecs/rt5645.c#L3582
> >
>
> Yes, I checked myself and send a patch to fix the binding description, which was
> missing the two suppliers.
>
>
> >>> + interrupt-parent = <&pio>;
> >>> + interrupts = <3 IRQ_TYPE_EDGE_BOTH>;
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 = <&rt5650_irq>;
> >>> + #sound-dai-cells = <1>;
> >>> + realtek,dmic1-data-pin = <2>;
> >>> + realtek,jd-mode = <2>;
> >>> + };
> >>> +
> >>> + ps8640: edp-bridge@8 {
> >>> + compatible = "parade,ps8640";
> >>> + reg = <0x8>;
> >>> + powerdown-gpios = <&pio 127 GPIO_ACTIVE_LOW>;
> >>> + reset-gpios = <&pio 115 GPIO_ACTIVE_LOW>;
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 = <&ps8640_pins>;
> >>> + vdd12-supply = <&ps8640_fixed_1v2>;
> >>> + vdd33-supply = <&mt6397_vgp2_reg>;
> >>> +
> >>> + ports {
> >>> + #address-cells = <1>;
> >>> + #size-cells = <0>;
> >>> +
> >>> + port@0 {
> >>> + reg = <0>;
> >>> +
> >>> + ps8640_in: endpoint {
> >>> + remote-endpoint = <&dsi0_out>;
> >>> + };
> >>> + };
> >>> +
> >>> + port@1 {
> >>> + reg = <1>;
> >>> +
> >>> + ps8640_out: endpoint {
> >>> + remote-endpoint = <&panel_in>;
> >>> + };
> >>> + };
> >>> + };
> >>> + };
> >>> +};
> >>> +
> >>> +&i2c1 {
> >>> + clock-frequency = <1500000>;
> >>> + status = "okay";
> >>> +
> >>> + da9211: da9211@68 {
> >>> + compatible = "dlg,da9211";
> >>> + reg = <0x68>;
> >>> +
> >>
> >> no interrupts? binding description have this stated as required. what happens
> >> when the device raises an interrupt?
> > Will double check on schematic and add it.
> >>
> >>> + regulators {
> >>> + da9211_vcpu_reg: BUCKA {
> >>> + regulator-name = "VBUCKA";
> >>> + regulator-min-microvolt = < 700000>;
> >>> + regulator-max-microvolt = <1310000>;
> >>> + regulator-min-microamp = <2000000>;
> >>> + regulator-max-microamp = <4400000>;
> >>> + regulator-ramp-delay = <10000>;
> >>> + regulator-always-on;
> >>> + regulator-allowed-modes = <0 1>;
> >>> + };
> >>> +
> >>> + da9211_vgpu_reg: BUCKB {
> >>> + regulator-name = "VBUCKB";
> >>> + regulator-min-microvolt = < 700000>;
> >>> + regulator-max-microvolt = <1310000>;
> >>> + regulator-min-microamp = <2000000>;
> >>> + regulator-max-microamp = <3000000>;
> >>> + regulator-ramp-delay = <10000>;
> >>> + };
> >>> + };
> >>> + };
> >>> +};
> >>> +
> >>> +&i2c2 {
> >>> + status = "okay";
> >>> +
> >>> + tpm: tpm@20 {
> >>> + compatible = "infineon,slb9645tt";
> >>> + reg = <0x20>;
> >>> + powered-while-suspended;
> >>> + };
> >>> +};
> >>> +
> >>> +&i2c3 {
> >>> + clock-frequency = <400000>;
> >>> + status = "okay";
> >>> +
> >>> + touchscreen: touchscreen@10 {
> >>> + compatible = "elan,ekth3500";
> >>> + reg = <0x10>;
> >>> + interrupt-parent = <&pio>;
> >>> + interrupts = <88 IRQ_TYPE_LEVEL_LOW>;
> >>> + };
> >>> +};
> >>> +
> >>> +&i2c4 {
> >>> + clock-frequency = <400000>;
> >>> + status = "okay";
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 = <&trackpad_irq>;
> >>
> >> Why not move the pinctrl properties into the trackpad node?
> >>
> > As second source trackpad device and original device shares same
> > compatible string (rev id), we need to add 2nd trackpad node here.
> > According to previous log (since I don't have a second source trackpad
> > device to test), adding pinctrl in each trackpad node, there would be
> > error:
> > [ 0.643501] mediatek-mt8173-pinctrl 1000b000.pinctrl: pin URXD3
> > already requested by 7-0015; cannot claim for 7-002c
> > [ 0.643525] mediatek-mt8173-pinctrl 1000b000.pinctrl: pin-117
> > (7-002c) status -22
> > [ 0.643548] mediatek-mt8173-pinctrl 1000b000.pinctrl: could not
> > request pin 117 (URXD3) from group URXD3 on device 1000b000.pinctrl
> > [ 0.643568] i2c_hid 7-002c: Error applying setting, reverse things back
> > [ 0.643867] i2c 7-002c: Driver i2c_hid requests probe deferral
> >
> >
>
> I think we can fix this, if we create the aforementioned two board DTS files.
> Correct?
>
> >>> +
> >>> + trackpad: trackpad@15 {
> >>> + compatible = "elan,ekth3000";
> >>> + interrupt-parent = <&pio>;
> >>> + interrupts = <117 IRQ_TYPE_LEVEL_LOW>;
> >>> + reg = <0x15>;
> >>> + vcc-supply = <&mt6397_vgp6_reg>;
> >>> + wakeup-source;
> >>> + };
> >>> +};
> >>> +
> >>> +&mipi_tx0 {
> >>> + status = "okay";
> >>> +};
> >>> +
> >>> +&mmc0 {
> >>> + status = "okay";
> >>> + pinctrl-names = "default", "state_uhs";
> >>> + pinctrl-0 = <&mmc0_pins_default>;
> >>> + pinctrl-1 = <&mmc0_pins_uhs>;
> >>> + bus-width = <8>;
> >>> + max-frequency = <200000000>;
> >>> + cap-mmc-highspeed;
> >>> + mmc-hs200-1_8v;
> >>> + mmc-hs400-1_8v;
> >>> + cap-mmc-hw-reset;
> >>> + hs400-ds-delay = <0x14015>;
> >>> + mediatek,hs200-cmd-int-delay=<30>;
> >>> + mediatek,hs400-cmd-int-delay=<14>;
> >>> + mediatek,hs400-cmd-resp-sel-rising;
> >>> + vmmc-supply = <&mt6397_vemc_3v3_reg>;
> >>> + vqmmc-supply = <&mt6397_vio18_reg>;
> >>> + assigned-clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>;
> >>> + assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL_D2>;
> >>> + non-removable;
> >>> +};
> >>> +
> >>> +&mmc1 {
> >>> + status = "okay";
> >>> + pinctrl-names = "default", "state_uhs";
> >>> + pinctrl-0 = <&mmc1_pins_default>;
> >>> + pinctrl-1 = <&mmc1_pins_uhs>;
> >>> + bus-width = <4>;
> >>> + max-frequency = <200000000>;
> >>> + cap-sd-highspeed;
> >>> + sd-uhs-sdr50;
> >>> + sd-uhs-sdr104;
> >>> + cd-gpios = <&pio 1 GPIO_ACTIVE_HIGH>;
> >>> + vmmc-supply = <&mt6397_vmch_reg>;
> >>> + vqmmc-supply = <&mt6397_vmc_reg>;
> >>> +};
> >>> +
> >>> +&mmc3 {
> >>> + status = "okay";
> >>> + pinctrl-names = "default", "state_uhs";
> >>> + pinctrl-0 = <&mmc3_pins_default>;
> >>> + pinctrl-1 = <&mmc3_pins_uhs>;
> >>> + bus-width = <4>;
> >>> + max-frequency = <200000000>;
> >>> + cap-sd-highspeed;
> >>> + sd-uhs-sdr50;
> >>> + sd-uhs-sdr104;
> >>> + sdr104-clk-delay = <5>;
> >>
> >> Not an upstream property, please delete it.
> >>
> >>> + keep-power-in-suspend;
> >>> + enable-sdio-wakeup;
> >>> + cap-sdio-irq;
> >>> + vmmc-supply = <&sdio_fixed_3v3>;
> >>> + vqmmc-supply = <&mt6397_vgp3_reg>;
> >>> + non-removable;
> >>> + cap-power-off-card;
> >>> +
> >>> + #address-cells = <1>;
> >>> + #size-cells = <0>;
> >>> +
> >>> + btmrvl: btmrvl@2 {
> >>> + compatible = "marvell,sd8897-bt";
> >>> + reg = <2>;
> >>> + interrupt-parent = <&pio>;
> >>> + interrupts = <119 IRQ_TYPE_LEVEL_LOW>;
> >>> + marvell,wakeup-pin = /bits/ 16 <0x0d>;
> >>> + marvell,wakeup-gap-ms = /bits/ 16 <0x64>;
> >>> + };
> >>> +
> >>> + mwifiex: mwifiex@1 {
> >>> + compatible = "marvell,sd8897";
> >>> + reg = <1>;
> >>> + interrupt-parent = <&pio>;
> >>> + interrupts = <38 IRQ_TYPE_LEVEL_LOW>;
> >>> + marvell,wakeup-pin = <3>;
> >>> + marvell,caldata_ed_mac = /bits/ 8 <
> >>> +0x01 0x00 0x07 0x00 0x14 0x00 0x01 0x00 0x00 0x00 0x12 0x00 0x02 0x00 0x01 0x00
> >>> +0x01 0x00 0x00 0x00 0x12 0x00 0x02 0x00 0x01 0x00
> >>> + >;
> >>
> >> Not an upstream property, please delete.
> >>
> >>> + };
> >>> +};
> >>> +
> >>> +&nor_flash {
> >>> + status = "okay";
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 = <&nor_gpio1_pins>;
> >>> + bus-width = <8>;
> >>> + max-frequency = <50000000>;
> >>> + non-removable;
> >>> + flash@0 {
> >>> + compatible = "jedec,spi-nor";
> >>> + reg = <0>;
> >>> + };
> >>> +};
> >>> +
> >>> +&pio {
> >>> + aud_i2s2: aud_i2s2 {
> >>> + pins1 {
> >>> + pinmux = <MT8173_PIN_128_I2S0_LRCK__FUNC_I2S1_WS>,
> >>> + <MT8173_PIN_129_I2S0_BCK__FUNC_I2S1_BCK>,
> >>> + <MT8173_PIN_130_I2S0_MCK__FUNC_I2S1_MCK>,
> >>> + <MT8173_PIN_131_I2S0_DATA0__FUNC_I2S1_DO_1>,
> >>> + <MT8173_PIN_12_EINT12__FUNC_I2S2_WS>,
> >>> + <MT8173_PIN_13_EINT13__FUNC_I2S2_BCK>,
> >>> + <MT8173_PIN_132_I2S0_DATA1__FUNC_I2S2_DI_2>;
> >>> + bias-pull-down;
> >>> + };
> >>> + };
> >>> +
> >>> + bl_fixed_pins: bl_fixed_pins {
> >>> + pins1 {
> >>> + pinmux = <MT8173_PIN_32_UTXD2__FUNC_GPIO32>;
> >>> + output-low;
> >>> + };
> >>> + };
> >>> +
> >>> + bt_wake_pins: bt_wake_pins {
> >>> + pins1 {
> >>> + pinmux = <MT8173_PIN_119_KPROW0__FUNC_GPIO119>;
> >>> + bias-pull-up;
> >>> + };
> >>> + };
> >>> +
> >>> + disp_pwm0_pins: disp_pwm0_pins {
> >>> + pins1 {
> >>> + pinmux = <MT8173_PIN_87_DISP_PWM0__FUNC_DISP_PWM0>;
> >>> + output-low;
> >>> + };
> >>> + };
> >>> +
> >>> + gpio_keys_pins: gpio_keys_pins {
> >>> + volume_pins {
> >>> + pinmux = <MT8173_PIN_123_KPCOL1__FUNC_GPIO123>,
> >>> + <MT8173_PIN_124_KPCOL2__FUNC_GPIO124>;
> >>> + bias-pull-up;
> >>> + };
> >>> +
> >>> + tablet_mode_pins {
> >>> + pinmux = <MT8173_PIN_121_KPROW2__FUNC_GPIO121>;
> >>> + bias-pull-up;
> >>> + };
> >>> + };
> >>> +
> >>> + hdmi_mux_pins: hdmi_mux_pins {
> >>> + pins1 {
> >>> + pinmux = <MT8173_PIN_36_DAISYNC__FUNC_GPIO36>;
> >>> + };
> >>> + };
> >>> +
> >>> + mmc0_pins_default: mmc0default {
> >>> + pins_cmd_dat {
> >>> + pinmux = <MT8173_PIN_57_MSDC0_DAT0__FUNC_MSDC0_DAT0>,
> >>> + <MT8173_PIN_58_MSDC0_DAT1__FUNC_MSDC0_DAT1>,
> >>> + <MT8173_PIN_59_MSDC0_DAT2__FUNC_MSDC0_DAT2>,
> >>> + <MT8173_PIN_60_MSDC0_DAT3__FUNC_MSDC0_DAT3>,
> >>> + <MT8173_PIN_61_MSDC0_DAT4__FUNC_MSDC0_DAT4>,
> >>> + <MT8173_PIN_62_MSDC0_DAT5__FUNC_MSDC0_DAT5>,
> >>> + <MT8173_PIN_63_MSDC0_DAT6__FUNC_MSDC0_DAT6>,
> >>> + <MT8173_PIN_64_MSDC0_DAT7__FUNC_MSDC0_DAT7>,
> >>> + <MT8173_PIN_66_MSDC0_CMD__FUNC_MSDC0_CMD>;
> >>> + bias-pull-up;
> >>> + };
> >>> +
> >>> + pins_clk {
> >>> + pinmux = <MT8173_PIN_65_MSDC0_CLK__FUNC_MSDC0_CLK>;
> >>> + bias-pull-down;
> >>
> >> identation.
> >>
> >>> + };
> >>> +
> >>> + pins_rst {
> >>> + pinmux = <MT8173_PIN_68_MSDC0_RST___FUNC_MSDC0_RSTB>;
> >>> + bias-pull-up;
> >>> + };
> >>> + };
> >>> +
> >>> + mmc1_pins_default: mmc1default {
> >>> + pins_cmd_dat {
> >>> + pinmux = <MT8173_PIN_73_MSDC1_DAT0__FUNC_MSDC1_DAT0>,
> >>> + <MT8173_PIN_74_MSDC1_DAT1__FUNC_MSDC1_DAT1>,
> >>> + <MT8173_PIN_75_MSDC1_DAT2__FUNC_MSDC1_DAT2>,
> >>> + <MT8173_PIN_76_MSDC1_DAT3__FUNC_MSDC1_DAT3>,
> >>> + <MT8173_PIN_78_MSDC1_CMD__FUNC_MSDC1_CMD>;
> >>> + input-enable;
> >>> + drive-strength = <MTK_DRIVE_4mA>;
> >>> + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
> >>> + };
> >>> +
> >>> + pins_clk {
> >>> + pinmux = <MT8173_PIN_77_MSDC1_CLK__FUNC_MSDC1_CLK>;
> >>> + bias-pull-down;
> >>> + drive-strength = <MTK_DRIVE_4mA>;
> >>> + };
> >>> +
> >>> + pins_insert {
> >>> + pinmux = <MT8173_PIN_1_EINT1__FUNC_GPIO1>;
> >>> + bias-pull-up;
> >>> + };
> >>> + };
> >>> +
> >>> + mmc3_pins_default: mmc3default {
> >>> + pins_dat {
> >>> + pinmux = <MT8173_PIN_22_MSDC3_DAT0__FUNC_MSDC3_DAT0>,
> >>> + <MT8173_PIN_23_MSDC3_DAT1__FUNC_MSDC3_DAT1>,
> >>> + <MT8173_PIN_24_MSDC3_DAT2__FUNC_MSDC3_DAT2>,
> >>> + <MT8173_PIN_25_MSDC3_DAT3__FUNC_MSDC3_DAT3>;
> >>> + input-enable;
> >>> + drive-strength = <MTK_DRIVE_8mA>;
> >>> + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
> >>> + };
> >>> +
> >>> + pins_cmd {
> >>> + pinmux = <MT8173_PIN_27_MSDC3_CMD__FUNC_MSDC3_CMD>;
> >>> + input-enable;
> >>> + drive-strength = <MTK_DRIVE_8mA>;
> >>> + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
> >>> + };
> >>> +
> >>> + pins_clk {
> >>> + pinmux = <MT8173_PIN_26_MSDC3_CLK__FUNC_MSDC3_CLK>;
> >>> + bias-pull-down;
> >>> + drive-strength = <MTK_DRIVE_8mA>;
> >>> + };
> >>> +
> >>> + pins_pdn {
> >>> + pinmux = <MT8173_PIN_85_AUD_DAT_MOSI__FUNC_GPIO85>;
> >>> + output-low;
> >>> + };
> >>> + };
> >>> +
> >>> + mmc0_pins_uhs: mmc0 {
> >>> + pins_cmd_dat {
> >>> + pinmux = <MT8173_PIN_57_MSDC0_DAT0__FUNC_MSDC0_DAT0>,
> >>> + <MT8173_PIN_58_MSDC0_DAT1__FUNC_MSDC0_DAT1>,
> >>> + <MT8173_PIN_59_MSDC0_DAT2__FUNC_MSDC0_DAT2>,
> >>> + <MT8173_PIN_60_MSDC0_DAT3__FUNC_MSDC0_DAT3>,
> >>> + <MT8173_PIN_61_MSDC0_DAT4__FUNC_MSDC0_DAT4>,
> >>> + <MT8173_PIN_62_MSDC0_DAT5__FUNC_MSDC0_DAT5>,
> >>> + <MT8173_PIN_63_MSDC0_DAT6__FUNC_MSDC0_DAT6>,
> >>> + <MT8173_PIN_64_MSDC0_DAT7__FUNC_MSDC0_DAT7>,
> >>> + <MT8173_PIN_66_MSDC0_CMD__FUNC_MSDC0_CMD>;
> >>> + input-enable;
> >>> + drive-strength = <MTK_DRIVE_6mA>;
> >>> + bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
> >>> + };
> >>> +
> >>> + pins_clk {
> >>> + pinmux = <MT8173_PIN_65_MSDC0_CLK__FUNC_MSDC0_CLK>;
> >>> + drive-strength = <MTK_DRIVE_6mA>;
> >>> + bias-pull-down = <MTK_PUPD_SET_R1R0_01>;
> >>> + };
> >>> +
> >>> + pins_ds {
> >>> + pinmux = <MT8173_PIN_67_MSDC0_DSL__FUNC_MSDC0_DSL>;
> >>> + drive-strength = <MTK_DRIVE_10mA>;
> >>> + bias-pull-down = <MTK_PUPD_SET_R1R0_01>;
> >>> + };
> >>> +
> >>> + pins_rst {
> >>> + pinmux = <MT8173_PIN_68_MSDC0_RST___FUNC_MSDC0_RSTB>;
> >>> + bias-pull-up;
> >>> + };
> >>> + };
> >>> +
> >>> + mmc1_pins_uhs: mmc1 {
> >>> + pins_cmd_dat {
> >>> + pinmux = <MT8173_PIN_73_MSDC1_DAT0__FUNC_MSDC1_DAT0>,
> >>> + <MT8173_PIN_74_MSDC1_DAT1__FUNC_MSDC1_DAT1>,
> >>> + <MT8173_PIN_75_MSDC1_DAT2__FUNC_MSDC1_DAT2>,
> >>> + <MT8173_PIN_76_MSDC1_DAT3__FUNC_MSDC1_DAT3>,
> >>> + <MT8173_PIN_78_MSDC1_CMD__FUNC_MSDC1_CMD>;
> >>> + input-enable;
> >>> + drive-strength = <MTK_DRIVE_6mA>;
> >>> + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
> >>> + };
> >>> +
> >>> + pins_clk {
> >>> + pinmux = <MT8173_PIN_77_MSDC1_CLK__FUNC_MSDC1_CLK>;
> >>> + drive-strength = <MTK_DRIVE_8mA>;
> >>> + bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
> >>> + };
> >>> + };
> >>> +
> >>> + mmc3_pins_uhs: mmc3 {
> >>> + pins_dat {
> >>> + pinmux = <MT8173_PIN_22_MSDC3_DAT0__FUNC_MSDC3_DAT0>,
> >>> + <MT8173_PIN_23_MSDC3_DAT1__FUNC_MSDC3_DAT1>,
> >>> + <MT8173_PIN_24_MSDC3_DAT2__FUNC_MSDC3_DAT2>,
> >>> + <MT8173_PIN_25_MSDC3_DAT3__FUNC_MSDC3_DAT3>;
> >>> + input-enable;
> >>> + drive-strength = <MTK_DRIVE_8mA>;
> >>> + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
> >>> + };
> >>> +
> >>> + pins_cmd {
> >>> + pinmux = <MT8173_PIN_27_MSDC3_CMD__FUNC_MSDC3_CMD>;
> >>> + input-enable;
> >>> + drive-strength = <MTK_DRIVE_8mA>;
> >>> + bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
> >>> + };
> >>> +
> >>> + pins_clk {
> >>> + pinmux = <MT8173_PIN_26_MSDC3_CLK__FUNC_MSDC3_CLK>;
> >>> + drive-strength = <MTK_DRIVE_8mA>;
> >>> + bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
> >>> + };
> >>> + };
> >>> +
> >>> + nor_gpio1_pins: nor {
> >>> + pins1 {
> >>> + pinmux = <MT8173_PIN_6_EINT6__FUNC_SFCS0>,
> >>> + <MT8173_PIN_7_EINT7__FUNC_SFHOLD>,
> >>> + <MT8173_PIN_8_EINT8__FUNC_SFIN>;
> >>> + input-enable;
> >>> + drive-strength = <MTK_DRIVE_4mA>;
> >>> + bias-pull-up;
> >>> + };
> >>> +
> >>> + pins2 {
> >>> + pinmux = <MT8173_PIN_5_EINT5__FUNC_SFOUT>;
> >>> + drive-strength = <MTK_DRIVE_4mA>;
> >>> + bias-pull-up;
> >>> + };
> >>> +
> >>> + pins_clk {
> >>> + pinmux = <MT8173_PIN_9_EINT9__FUNC_SFCK>;
> >>> + input-enable;
> >>> + drive-strength = <MTK_DRIVE_4mA>;
> >>> + bias-pull-up;
> >>> + };
> >>> + };
> >>> +
> >>> + panel_fixed_pins: panel_fixed_pins {
> >>> + pins1 {
> >>> + pinmux = <MT8173_PIN_41_CMMCLK__FUNC_GPIO41>;
> >>> + };
> >>> + };
> >>> +
> >>> + ps8640_pins: ps8640_pins {
> >>> + pins1 {
> >>> + pinmux = <MT8173_PIN_92_PCM_CLK__FUNC_GPIO92>,
> >>> + <MT8173_PIN_115_URTS0__FUNC_GPIO115>,
> >>> + <MT8173_PIN_127_LCM_RST__FUNC_GPIO127>;
> >>> + };
> >>> + };
> >>> +
> >>> + ps8640_fixed_pins: ps8640_fixed_pins {
> >>> + pins1 {
> >>> + pinmux = <MT8173_PIN_30_URTS2__FUNC_GPIO30>;
> >>> + };
> >>> + };
> >>> +
> >>> + rt5650_irq: rt5650_irq {
> >>> + pins1 {
> >>> + pinmux = <MT8173_PIN_3_EINT3__FUNC_GPIO3>;
> >>> + bias-pull-down;
> >>> + };
> >>> + };
> >>> +
> >>> + spi_pins_a: spi1 {
> >>> + pins1 {
> >>> + pinmux = <MT8173_PIN_0_EINT0__FUNC_GPIO0>;
> >>> + bias-pull-up;
> >>> + };
> >>> +
> >>> + pins_spi {
> >>> + pinmux = <MT8173_PIN_102_MSDC2_DAT2__FUNC_SPI_CK_1_>,
> >>> + <MT8173_PIN_103_MSDC2_DAT3__FUNC_SPI_MI_1_>,
> >>> + <MT8173_PIN_104_MSDC2_CLK__FUNC_SPI_MO_1_>,
> >>> + <MT8173_PIN_105_MSDC2_CMD__FUNC_SPI_CS_1_>;
> >>> + bias-disable;
> >>> + };
> >>> + };
> >>> +
> >>> + trackpad_irq: trackpad_irq {
> >>> + pins1 {
> >>> + pinmux = <MT8173_PIN_117_URXD3__FUNC_GPIO117>;
> >>> + input-enable;
> >>> + bias-pull-up;
> >>> + };
> >>> + };
> >>> +
> >>> + usb_pins: usb@0 {
> >>> + pins1 {
> >>> + pinmux = <MT8173_PIN_101_MSDC2_DAT1__FUNC_GPIO101>;
> >>> + output-high;
> >>> + bias-disable;
> >>> + };
> >>> + };
> >>> +
> >>> + wifi_wake_pins: wifi_wake_pins {
> >>> + pins1 {
> >>> + pinmux = <MT8173_PIN_38_CONN_RST__FUNC_GPIO38>;
> >>> + bias-pull-up;
> >>> + };
> >>> + };
> >>> +};
> >>> +
> >>> +&pwm0 {
> >>> + status = "okay";
> >>> +};
> >>> +
> >>> +&pwrap {
> >>> + pmic: mt6397 {
> >>> + compatible = "mediatek,mt6397";
> >>> + #address-cells = <1>;
> >>> + #size-cells = <1>;
> >>> + interrupt-parent = <&pio>;
> >>> + interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
> >>> + interrupt-controller;
> >>> + #interrupt-cells = <2>;
> >>> +
> >>> + mt6397rtc: mt6397rtc {
> >>
> >> AFAIK this should be
> >> rtc: mt6397rtc {
> >>
> >> Please fix that for all subnodes.
> >>
> > Will fix in next version
> >>> + compatible = "mediatek,mt6397-rtc";
> >>> + };
> >>> +
> >>> + syscfg_pctl_pmic: syscfg_pctl_pmic@c000 {
> >>> + compatible = "mediatek,mt6397-pctl-pmic-syscfg",
> >>> + "syscon";
> >>> + reg = <0 0x0000c000 0 0x0108>;
> >>
> >> not an upstream compatible, please delete the node.
> >>
>
> I think my comment was not correct. I'll have to dig more to understand why we
> have a compatible without a binding description.
>
Here's a similar syscon node that is in a binding document's example:
syscfg_pctl_a: syscfg-pctl-a@10005000 {
compatible = "mediatek,mt8135-pctl-a-syscfg", "syscon";
reg = <0 0x10005000 0 0x1000>;
};
https://elixir.bootlin.com/linux/latest/source/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt#L81
> Regards,
> Matthias
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH v2 1/2] dt-bindings: arm64: dts: mediatek: Add mt8173 elm and hana
2020-01-10 7:37 ` [PATCH v2 1/2] dt-bindings: arm64: dts: mediatek: Add mt8173 elm and hana Hsin-Yi Wang
2020-01-10 11:38 ` Enric Balletbo i Serra
@ 2020-01-15 14:52 ` Rob Herring
1 sibling, 0 replies; 14+ messages in thread
From: Rob Herring @ 2020-01-15 14:52 UTC (permalink / raw)
To: Hsin-Yi Wang
Cc: Mark Rutland, devicetree, Nicolas Boichat, linux-kernel,
Daniel Kurtz, Enric Balletbo i Serra, linux-mediatek,
Matthias Brugger, linux-arm-kernel
On Fri, 10 Jan 2020 15:37:29 +0800, Hsin-Yi Wang wrote:
> Elm is Acer Chromebook R13. Hana is Lenovo Chromebook. Both uses mt8173
> SoC.
>
> Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
> ---
> Changes in v2:
> - fix dtbs_check errors, use const instead of enum
> ---
> .../devicetree/bindings/arm/mediatek.yaml | 27 +++++++++++++++++++
> 1 file changed, 27 insertions(+)
>
Reviewed-by: Rob Herring <robh@kernel.org>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH v2 2/2] arm64: dts: mediatek: add mt8173 elm and hana board
2020-01-15 8:53 ` Hsin-Yi Wang
@ 2020-01-15 16:14 ` Matthias Brugger
0 siblings, 0 replies; 14+ messages in thread
From: Matthias Brugger @ 2020-01-15 16:14 UTC (permalink / raw)
To: Hsin-Yi Wang
Cc: Mark Rutland, Devicetree List, Nicolas Boichat, lkml,
Daniel Kurtz, Rob Herring, linux-mediatek,
Enric Balletbo i Serra,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE
On 15/01/2020 09:53, Hsin-Yi Wang wrote:
> On Tue, Jan 14, 2020 at 11:10 PM Matthias Brugger
> <matthias.bgg@gmail.com> wrote:
>>
>>
>>
>> On 13/01/2020 19:01, Hsin-Yi Wang wrote:
>>> On Fri, Jan 10, 2020 at 9:42 PM Matthias Brugger <matthias.bgg@gmail.com> wrote:
>>>>
>>>>
>>> Thanks, I will address the comments and send next version
>>>>
>>>> On 10/01/2020 08:37, Hsin-Yi Wang wrote:
>>>>> Elm is Acer Chromebook R13. Hana is Lenovo Chromebook. Both uses mt8173
>>>>> SoC.
>>>>>
>>>>> Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
>>>>> ---
>>>>> Changes in v2:
>>>>> - remove downstream nodes and unused nodes
>>>>> - use GPIO_ACTIVE_LOW for ps8640 gpios
>>>>> - move trackpad to hana
>>>>> ---
>>>>> arch/arm64/boot/dts/mediatek/Makefile | 3 +
>>>>> .../dts/mediatek/mt8173-elm-hana-rev7.dts | 27 +
>>>>> .../boot/dts/mediatek/mt8173-elm-hana.dts | 16 +
>>>>> .../boot/dts/mediatek/mt8173-elm-hana.dtsi | 60 +
>>>>> arch/arm64/boot/dts/mediatek/mt8173-elm.dts | 15 +
>>>>> arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi | 1040 +++++++++++++++++
>>>>> 6 files changed, 1161 insertions(+)
>>>>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts
>>>>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dts
>>>>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm-hana.dtsi
>>>>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm.dts
>>>>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi
>>>>>
[...]
>>>>> + compatible = "mediatek,mt6397-rtc";
>>>>> + };
>>>>> +
>>>>> + syscfg_pctl_pmic: syscfg_pctl_pmic@c000 {
>>>>> + compatible = "mediatek,mt6397-pctl-pmic-syscfg",
>>>>> + "syscon";
>>>>> + reg = <0 0x0000c000 0 0x0108>;
>>>>
>>>> not an upstream compatible, please delete the node.
>>>>
>>
>> I think my comment was not correct. I'll have to dig more to understand why we
>> have a compatible without a binding description.
>>
> Here's a similar syscon node that is in a binding document's example:
>
> syscfg_pctl_a: syscfg-pctl-a@10005000 {
> compatible = "mediatek,mt8135-pctl-a-syscfg", "syscon";
> reg = <0 0x10005000 0 0x1000>;
> };
>
> https://elixir.bootlin.com/linux/latest/source/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt#L81
>
Yes I know, that's why I said that my first comment was not correct. Just leave
it in.
Regards,
Matthias
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 14+ messages in thread
end of thread, other threads:[~2020-01-15 16:14 UTC | newest]
Thread overview: 14+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-01-10 7:37 [PATCH v2 0/2] Add mt8173 elm and hana board Hsin-Yi Wang
2020-01-10 7:37 ` [PATCH v2 1/2] dt-bindings: arm64: dts: mediatek: Add mt8173 elm and hana Hsin-Yi Wang
2020-01-10 11:38 ` Enric Balletbo i Serra
2020-01-15 14:52 ` Rob Herring
2020-01-10 7:37 ` [PATCH v2 2/2] arm64: dts: mediatek: add mt8173 elm and hana board Hsin-Yi Wang
2020-01-10 8:52 ` Yingjoe Chen
2020-01-10 13:42 ` Matthias Brugger
2020-01-13 18:01 ` Hsin-Yi Wang
2020-01-14 15:10 ` Matthias Brugger
2020-01-14 15:33 ` Hsin-Yi Wang
2020-01-15 8:53 ` Hsin-Yi Wang
2020-01-15 16:14 ` Matthias Brugger
2020-01-13 9:29 ` Enric Balletbo i Serra
2020-01-13 18:18 ` Matthias Kaehlcke
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).