From: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
To: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>, olof@lixom.net
Cc: Mark Rutland <mark.rutland@arm.com>,
devicetree@vger.kernel.org, mbrugger@suse.com, maz@kernel.org,
f.fainelli@gmail.com, phil@raspberrypi.org,
linux-kernel@vger.kernel.org, jeremy.linton@arm.com,
Rob Herring <robh+dt@kernel.org>,
bcm-kernel-feedback-list@broadcom.com, wahrenst@gmx.net,
james.quinlan@broadcom.com, linux-pci@vger.kernel.org,
andrew.murray@arm.com, linux-arm-kernel@lists.infradead.org,
linux-rpi-kernel@lists.infradead.org
Subject: Re: [PATCH v5 2/6] ARM: dts: bcm2711: Enable PCIe controller
Date: Tue, 14 Jan 2020 18:11:59 +0000 [thread overview]
Message-ID: <20200114181159.GB11177@e121166-lin.cambridge.arm.com> (raw)
In-Reply-To: <20191216110113.30436-3-nsaenzjulienne@suse.de>
On Mon, Dec 16, 2019 at 12:01:08PM +0100, Nicolas Saenz Julienne wrote:
> This enables bcm2711's PCIe bus, which is hardwired to a VIA
> Technologies XHCI USB 3.0 controller.
>
> Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
>
> ---
>
> Changes since v4:
> - Rebase commit taking into account genet support series
>
> Changes since v3:
> - Remove unwarranted comment
>
> Changes since v2:
> - Remove unused interrupt-map
> - correct dma-ranges to it's full size, non power of 2 bus DMA
> constraints now supported in linux-next[1]
> - add device_type
> - rename alias from pcie_0 to pcie0
>
> Changes since v1:
> - remove linux,pci-domain
>
> [1] https://lkml.org/lkml/2019/11/21/235
>
> arch/arm/boot/dts/bcm2711.dtsi | 31 ++++++++++++++++++++++++++++++-
> 1 file changed, 30 insertions(+), 1 deletion(-)
Olof as we discussed previously, I will not merge this dts change and
drop it from the series - Nicolas should redirect it to arm-soc, please
let me know if my understanding is correct.
Thanks,
Lorenzo
> diff --git a/arch/arm/boot/dts/bcm2711.dtsi b/arch/arm/boot/dts/bcm2711.dtsi
> index e2f6ffb00aa9..b56388ce1216 100644
> --- a/arch/arm/boot/dts/bcm2711.dtsi
> +++ b/arch/arm/boot/dts/bcm2711.dtsi
> @@ -331,7 +331,36 @@ scb {
> #address-cells = <2>;
> #size-cells = <1>;
>
> - ranges = <0x0 0x7c000000 0x0 0xfc000000 0x03800000>;
> + ranges = <0x0 0x7c000000 0x0 0xfc000000 0x03800000>,
> + <0x6 0x00000000 0x6 0x00000000 0x40000000>;
> +
> + pcie0: pcie@7d500000 {
> + compatible = "brcm,bcm2711-pcie";
> + reg = <0x0 0x7d500000 0x9310>;
> + device_type = "pci";
> + #address-cells = <3>;
> + #interrupt-cells = <1>;
> + #size-cells = <2>;
> + interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "pcie", "msi";
> + interrupt-map-mask = <0x0 0x0 0x0 0x7>;
> + interrupt-map = <0 0 0 1 &gicv2 GIC_SPI 143
> + IRQ_TYPE_LEVEL_HIGH>;
> + msi-controller;
> + msi-parent = <&pcie0>;
> +
> + ranges = <0x02000000 0x0 0xf8000000 0x6 0x00000000
> + 0x0 0x04000000>;
> + /*
> + * The wrapper around the PCIe block has a bug
> + * preventing it from accessing beyond the first 3GB of
> + * memory.
> + */
> + dma-ranges = <0x02000000 0x0 0x00000000 0x0 0x00000000
> + 0x0 0xc0000000>;
> + brcm,enable-ssc;
> + };
>
> genet: ethernet@7d580000 {
> compatible = "brcm,bcm2711-genet-v5";
> --
> 2.24.0
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2020-01-14 18:12 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-12-16 11:01 [PATCH v5 0/6] Raspberry Pi 4 PCIe support Nicolas Saenz Julienne
2019-12-16 11:01 ` [PATCH v5 1/6] dt-bindings: PCI: Add bindings for brcmstb's PCIe device Nicolas Saenz Julienne
2019-12-16 11:14 ` Matthias Brugger
2019-12-16 11:18 ` Nicolas Saenz Julienne
2019-12-16 11:01 ` [PATCH v5 2/6] ARM: dts: bcm2711: Enable PCIe controller Nicolas Saenz Julienne
2020-01-14 18:11 ` Lorenzo Pieralisi [this message]
2020-01-14 18:15 ` Florian Fainelli
2020-01-15 23:41 ` Florian Fainelli
2019-12-16 11:01 ` [PATCH v5 3/6] PCI: brcmstb: Add Broadcom STB PCIe host controller driver Nicolas Saenz Julienne
2020-01-14 17:11 ` Lorenzo Pieralisi
2020-01-14 18:18 ` Nicolas Saenz Julienne
2020-01-15 10:00 ` Lorenzo Pieralisi
2020-01-15 11:29 ` Nicolas Saenz Julienne
2019-12-16 11:01 ` [PATCH v5 4/6] PCI: brcmstb: Add MSI support Nicolas Saenz Julienne
2019-12-16 11:01 ` [PATCH v5 6/6] arm64: defconfig: Enable Broadcom's STB PCIe controller Nicolas Saenz Julienne
2020-01-16 17:21 ` Florian Fainelli
2019-12-16 11:36 ` [PATCH v5 0/6] Raspberry Pi 4 PCIe support Andrew Murray
2019-12-16 11:45 ` Nicolas Saenz Julienne
2020-01-15 12:02 ` Lorenzo Pieralisi
2020-01-15 12:45 ` Nicolas Saenz Julienne
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200114181159.GB11177@e121166-lin.cambridge.arm.com \
--to=lorenzo.pieralisi@arm.com \
--cc=andrew.murray@arm.com \
--cc=bcm-kernel-feedback-list@broadcom.com \
--cc=devicetree@vger.kernel.org \
--cc=f.fainelli@gmail.com \
--cc=james.quinlan@broadcom.com \
--cc=jeremy.linton@arm.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pci@vger.kernel.org \
--cc=linux-rpi-kernel@lists.infradead.org \
--cc=mark.rutland@arm.com \
--cc=maz@kernel.org \
--cc=mbrugger@suse.com \
--cc=nsaenzjulienne@suse.de \
--cc=olof@lixom.net \
--cc=phil@raspberrypi.org \
--cc=robh+dt@kernel.org \
--cc=wahrenst@gmx.net \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).