From: Sasha Levin <sashal@kernel.org>
To: linux-kernel@vger.kernel.org, stable@vger.kernel.org
Cc: Sasha Levin <sashal@kernel.org>,
devicetree@vger.kernel.org,
Alexandre Belloni <alexandre.belloni@bootlin.com>,
Peter Rosin <peda@axentia.se>,
linux-arm-kernel@lists.infradead.org
Subject: [PATCH AUTOSEL 4.19 002/671] ARM: dts: at91: nattis: set the PRLUD and HIPOW signals low
Date: Thu, 16 Jan 2020 11:43:53 -0500 [thread overview]
Message-ID: <20200116165502.8838-2-sashal@kernel.org> (raw)
In-Reply-To: <20200116165502.8838-1-sashal@kernel.org>
From: Peter Rosin <peda@axentia.se>
[ Upstream commit 29feb2c960ab32fc24249443d4434194ce96f083 ]
AT91_PINCTRL_OUTPUT_VAL(0) without AT91_PINCTRL_OUTPUT is a no-op, so
make sure the pins really output a zero.
Fixes: 0e4323899973 ("ARM: dts: at91: add devicetree for the Axentia Nattis with Natte power")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
arch/arm/boot/dts/at91-nattis-2-natte-2.dts | 6 ++++--
1 file changed, 4 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/at91-nattis-2-natte-2.dts b/arch/arm/boot/dts/at91-nattis-2-natte-2.dts
index af9f38456d04..bfa5815a0721 100644
--- a/arch/arm/boot/dts/at91-nattis-2-natte-2.dts
+++ b/arch/arm/boot/dts/at91-nattis-2-natte-2.dts
@@ -38,14 +38,16 @@
atmel,pins =
<AT91_PIOA 21
AT91_PERIPH_GPIO
- AT91_PINCTRL_OUTPUT_VAL(0)>;
+ (AT91_PINCTRL_OUTPUT |
+ AT91_PINCTRL_OUTPUT_VAL(0))>;
};
pinctrl_lcd_hipow0: lcd_hipow0 {
atmel,pins =
<AT91_PIOA 23
AT91_PERIPH_GPIO
- AT91_PINCTRL_OUTPUT_VAL(0)>;
+ (AT91_PINCTRL_OUTPUT |
+ AT91_PINCTRL_OUTPUT_VAL(0))>;
};
};
};
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next parent reply other threads:[~2020-01-16 17:00 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <20200116165502.8838-1-sashal@kernel.org>
2020-01-16 16:43 ` Sasha Levin [this message]
2020-01-16 16:43 ` [PATCH AUTOSEL 4.19 003/671] ARM: dts: at91: nattis: make the SD-card slot work Sasha Levin
2020-01-16 16:44 ` [PATCH AUTOSEL 4.19 010/671] ARM: qcom_defconfig: Enable MAILBOX Sasha Levin
2020-01-16 16:44 ` [PATCH AUTOSEL 4.19 012/671] PCI: iproc: Remove PAXC slot check to allow VF support Sasha Levin
2020-01-16 16:44 ` [PATCH AUTOSEL 4.19 018/671] mailbox: mediatek: Add check for possible failure of kzalloc Sasha Levin
2020-01-16 16:44 ` [PATCH AUTOSEL 4.19 041/671] drm/sun4i: hdmi: Fix double flag assignation Sasha Levin
2020-01-16 16:44 ` [PATCH AUTOSEL 4.19 047/671] ARM: dts: bcm283x: Correct mailbox register sizes Sasha Levin
2020-01-16 16:44 ` [PATCH AUTOSEL 4.19 049/671] ASoC: sun8i-codec: add missing route for ADC Sasha Levin
2020-01-16 16:44 ` [PATCH AUTOSEL 4.19 050/671] pinctrl: meson-gxl: remove invalid GPIOX tsin_a pins Sasha Levin
2020-01-16 16:44 ` [PATCH AUTOSEL 4.19 057/671] arm64: dts: meson-gx: Add hdmi_5v regulator as hdmi tx supply Sasha Levin
2020-01-16 16:44 ` [PATCH AUTOSEL 4.19 064/671] staging: bcm2835-camera: Abort probe if there is no camera Sasha Levin
2020-01-16 16:44 ` [PATCH AUTOSEL 4.19 065/671] staging: bcm2835-camera: fix module autoloading Sasha Levin
2020-01-16 16:45 ` [PATCH AUTOSEL 4.19 088/671] clk: samsung: exynos4: fix refcount leak in exynos4_get_xom() Sasha Levin
2020-01-16 16:45 ` [PATCH AUTOSEL 4.19 089/671] clk: imx6q: fix refcount leak in imx6q_clocks_init() Sasha Levin
2020-01-16 16:45 ` [PATCH AUTOSEL 4.19 090/671] clk: imx6sx: fix refcount leak in imx6sx_clocks_init() Sasha Levin
2020-01-16 16:45 ` [PATCH AUTOSEL 4.19 091/671] clk: imx7d: fix refcount leak in imx7d_clocks_init() Sasha Levin
2020-01-16 16:45 ` [PATCH AUTOSEL 4.19 092/671] clk: vf610: fix refcount leak in vf610_clocks_init() Sasha Levin
2020-01-16 16:45 ` [PATCH AUTOSEL 4.19 098/671] MIPS: BCM63XX: drop unused and broken DSP platform device Sasha Levin
2020-01-16 16:45 ` [PATCH AUTOSEL 4.19 099/671] arm64: defconfig: Re-enable bcm2835-thermal driver Sasha Levin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200116165502.8838-2-sashal@kernel.org \
--to=sashal@kernel.org \
--cc=alexandre.belloni@bootlin.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=peda@axentia.se \
--cc=stable@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).