From: Li Yang <leoyang.li@nxp.com>
To: shawnguo@kernel.org, linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org, Li Yang <leoyang.li@nxp.com>
Subject: [PATCH v2 14/15] arm64: defconfig: Enable PHY devices used on QorIQ boards
Date: Wed, 11 Mar 2020 17:53:16 -0500 [thread overview]
Message-ID: <20200311225317.11198-15-leoyang.li@nxp.com> (raw)
In-Reply-To: <20200311225317.11198-1-leoyang.li@nxp.com>
Enables various PHY device drivers and PHY MUX drivers used on QorIQ
reference boards supported in mainline kernel.
Enabled as built-in to boot from network without an initramfs.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
---
arch/arm64/configs/defconfig | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index b092adecf724..a6e9d046e65d 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -306,13 +306,17 @@ CONFIG_SNI_AVE=y
CONFIG_SNI_NETSEC=y
CONFIG_STMMAC_ETH=m
CONFIG_MDIO_BUS_MUX_MMIOREG=y
+CONFIG_MDIO_BUS_MUX_MULTIPLEXER=y
+CONFIG_AQUANTIA_PHY=y
CONFIG_MARVELL_PHY=m
CONFIG_MARVELL_10G_PHY=m
CONFIG_MESON_GXL_PHY=m
CONFIG_MICREL_PHY=y
+CONFIG_MICROSEMI_PHY=y
CONFIG_AT803X_PHY=y
CONFIG_REALTEK_PHY=m
CONFIG_ROCKCHIP_PHY=y
+CONFIG_VITESSE_PHY=y
CONFIG_USB_PEGASUS=m
CONFIG_USB_RTL8150=m
CONFIG_USB_RTL8152=m
@@ -880,6 +884,7 @@ CONFIG_FPGA_REGION=m
CONFIG_OF_FPGA_REGION=m
CONFIG_TEE=y
CONFIG_OPTEE=y
+CONFIG_MUX_MMIO=y
CONFIG_EXT2_FS=y
CONFIG_EXT3_FS=y
CONFIG_EXT4_FS_POSIX_ACL=y
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2020-03-11 22:58 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-03-11 22:53 [PATCH v2 00/15] Enable drivers for NXP/FSL QorIQ arm64 boards Li Yang
2020-03-11 22:53 ` [PATCH v2 01/15] arm64: defconfig: run through savedefconfig for ordering Li Yang
2020-03-11 22:53 ` [PATCH v2 02/15] arm64: defconfig: Enable NXP flexcan driver Li Yang
2020-03-11 22:53 ` [PATCH v2 03/15] arm64: defconfig: Enable QorIQ DPAA1 drivers Li Yang
2020-03-11 22:53 ` [PATCH v2 04/15] arm64: defconfig: Enable QorIQ DPAA2 drivers Li Yang
2020-03-11 22:53 ` [PATCH v2 05/15] arm64: defconfig: Enable ENETC Ethernet controller and FELIX switch Li Yang
2020-03-11 22:53 ` [PATCH v2 06/15] arm64: defconfig: Enable NXP/FSL SPI controller drivers Li Yang
2020-03-11 22:53 ` [PATCH v2 07/15] arm64: defconfig: Enable QorIQ cpufreq driver Li Yang
2020-03-11 22:53 ` [PATCH v2 08/15] arm64: defconfig: Enable ARM SBSA watchdog driver Li Yang
2020-03-11 22:53 ` [PATCH v2 09/15] arm64: defconfig: Enable QorIQ IFC NAND controller driver Li Yang
2020-03-11 22:53 ` [PATCH v2 10/15] arm64: defconfig: Enable QorIQ GPIO driver Li Yang
2020-03-11 22:53 ` [PATCH v2 11/15] arm64: defconfig: Enable ARM Mali display driver Li Yang
2020-03-11 22:53 ` [PATCH v2 12/15] arm64: defconfig: Enable flash device drivers for QorIQ boards Li Yang
2020-03-11 22:53 ` [PATCH v2 13/15] arm64: defconfig: Enable RTC devices " Li Yang
2020-03-11 22:53 ` Li Yang [this message]
2020-03-11 22:53 ` [PATCH v2 15/15] arm64: defconfig: Enable e1000 device Li Yang
2020-03-16 1:33 ` [PATCH v2 00/15] Enable drivers for NXP/FSL QorIQ arm64 boards Shawn Guo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200311225317.11198-15-leoyang.li@nxp.com \
--to=leoyang.li@nxp.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).