Re: [PATCH 0/3] arm64: Open code .arch_extension

From: Catalin Marinas <catalin.marinas@arm.com>
To: Mark Brown <broonie@kernel.org>
Cc: Eric Biggers <ebiggers@google.com>, Will Deacon <will@kernel.org>,
	Ard Biesheuvel <ardb@kernel.org>,
	linux-arm-kernel@lists.infradead.org,
	linux-crypto@vger.kernel.org
Subject: Re: [PATCH 0/3] arm64: Open code .arch_extension
Date: Thu, 23 Apr 2020 12:59:05 +0100	[thread overview]
Message-ID: <20200423115905.GE4963@gaia> (raw)
In-Reply-To: <20200423111803.GG4808@sirena.org.uk>

On Thu, Apr 23, 2020 at 12:18:03PM +0100, Mark Brown wrote:
> On Wed, Apr 22, 2020 at 07:00:28PM +0100, Catalin Marinas wrote:
> > On Wed, Mar 25, 2020 at 11:50:38AM +0000, Mark Brown wrote:
> > > Since BTI is a mandatory feature of v8.5 there is no BTI arch_extension,
> > > you can only enable it by moving the base architecture to v8.5.  You'd
> > > need to use .arch and that feels likely to find us sharp edges to run
> > > into.
> 
> > For MTE, .arch armv8-a+memtag won't work since this is only available
> > with armv8.5-a. My preference would be to have the highest arch version
> > supported by the kernel in the assembler.h file, i.e. ".arch armv8.5-a"
> > followed by .arch_extension in each .S file, as needed.
> 
> I think we decided that .arch_extension was too new to be used for
> things like the crypto stuff where we still support older toolchains?

.arch_extension would be issued conditionally only for features like
CONFIG_ARM64_MTE which already have a dependency on a newer toolchain.

However, '.arch_extension memtag' is not sufficient for MTE, it needs a
prior '.arch armv8.5-a'.

> > Forcing .S files to armv8.5 would not cause any problems with
> > the base armv8.0 that the kernel image support since it shouldn't change
> > the opcodes gas generates. The .S files would use alternatives anyway
> > (or simply have code not called).
> 
> We do loose the checking that the assembler does that nobody used a
> newer feature by mistake but yeah, shouldn't affect the output.

We may need some push/pop_arch macros to contain the supported features.

The gas documentation says that .arch_extension may be used multiple
times to add or remove extensions. However, I couldn't find a way to
remove memtag after adding it (tried -memtag, !memtag, empty string). So
I may go with a '.arch armv8.0-a' as a base, followed by temporary
setting of '.arch armv8.5-a+memtag' (and hope we don't need combinations
of such extensions).

> > The inline asm is slightly more problematic, especially with the clang
> > builtin assembler which goes in a single pass. But we could do something
> > similar to what we did with the LSE atomics and raising the base of the
> > inline asm to armv8.5 (or 8.6 etc., whatever we need in the future).
> 
> FWIW I did something different to this for BTI so I wasn't using the
> instructions directly so I was going to abandon this series.

I can't work around this easily for MTE, there are more instructions
with register encoding. I'll see if the push/pop idea works or just
leave it to whoever does the next feature, figure out how it interacts
with MTE ;).

-- 
Catalin

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel