From: Lee Jones <lee.jones@linaro.org>
To: Michael Walle <michael@walle.cc>
Cc: devicetree@vger.kernel.org, arnd@arndb.de,
gregkh@linuxfoundation.org, linus.walleij@linaro.org,
linux-kernel@vger.kernel.org, robh+dt@kernel.org,
bgolaszewski@baylibre.com, broonie@kernel.org,
andriy.shevchenko@linux.intel.com,
linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH v4 1/1] mfd: Add I2C based System Configuaration (SYSCON) access
Date: Thu, 2 Jul 2020 08:14:02 +0100 [thread overview]
Message-ID: <20200702071402.GP1179328@dell> (raw)
In-Reply-To: <e436fd60bf0ebb6d72a76034d0fc35de@walle.cc>
On Tue, 30 Jun 2020, Michael Walle wrote:
> Hi Lee,
>
> I'm just trying to use this for my sl28 driver. Some remarks, see below.
>
> Am 2020-06-22 09:51, schrieb Lee Jones:
> > The existing SYSCON implementation only supports MMIO (memory mapped)
> > accesses, facilitated by Regmap. This extends support for registers
> > held behind I2C busses.
> >
> > Signed-off-by: Lee Jones <lee.jones@linaro.org>
> > ---
> > Changelog:
> >
> > v3 => v4
> > - Add ability to provide a non-default Regmap configuration
> >
> > v2 => v3
> > - Change 'is CONFIG' present check to include loadable modules
> > - s/#ifdef CONFIG_MFD_SYSCON_I2C/#if
> > IS_ENABLED(CONFIG_MFD_SYSCON_I2C)/
> >
> > v1 => v2
> > - Remove legacy references to OF
> > - Allow building as a module (fixes h8300 0-day issue)
> >
> > drivers/mfd/Kconfig | 7 +++
> > drivers/mfd/Makefile | 1 +
> > drivers/mfd/syscon-i2c.c | 104 +++++++++++++++++++++++++++++++++
> > include/linux/mfd/syscon-i2c.h | 36 ++++++++++++
> > 4 files changed, 148 insertions(+)
> > create mode 100644 drivers/mfd/syscon-i2c.c
> > create mode 100644 include/linux/mfd/syscon-i2c.h
> >
>
> [..]
>
> > +static struct regmap *syscon_i2c_get_regmap(struct i2c_client *client,
> > + struct regmap_config *regmap_config)
> > +{
> > + struct device *dev = &client->dev;
> > + struct syscon *entry, *syscon = NULL;
> > +
> > + spin_lock(&syscon_i2c_list_slock);
> > +
> > + list_for_each_entry(entry, &syscon_i2c_list, list)
> > + if (entry->dev == dev) {
> > + syscon = entry;
> > + break;
> > + }
> > +
> > + spin_unlock(&syscon_i2c_list_slock);
> > +
> > + if (!syscon)
> > + syscon = syscon_i2c_register(client, regmap_config);
> > +
> > + if (IS_ERR(syscon))
> > + return ERR_CAST(syscon);
> > +
> > + return syscon->regmap;
> > +}
> > +
> > +struct regmap *syscon_i2c_to_regmap_config(struct i2c_client *client,
> > + struct regmap_config *regmap_config)
> > +{
> > + return syscon_i2c_get_regmap(client, regmap_config);
> > +}
> > +EXPORT_SYMBOL_GPL(syscon_i2c_to_regmap_config);
> > +
> > +struct regmap *syscon_i2c_to_regmap(struct i2c_client *client)
> > +{
> > + return syscon_i2c_get_regmap(client, &syscon_i2c_regmap_config);
> > +}
> > +EXPORT_SYMBOL_GPL(syscon_i2c_to_regmap);
>
> What do you think about
>
> struct regmap *syscon_i2c_to_regmap(struct device *dev)
> {
> struct i2c_client *client = i2c_verify_client(dev);
>
> if (!client)
> return ERR_PTR(-EINVAL);
>
> return syscon_i2c_get_regmap(client, &syscon_i2c_regmap_config);
> }
>
> Or even move it to syscon_i2c_get_regmap().
>
> This way, (a) a driver doesn't have to use "#include <linux/i2c.h>" just
> to call to_i2c_client() (or i2c_verify_client()) and (b) you won't do it
> all over again in all sub drivers.
What is your use-case? This is set-up for based I2C drivers to call
into. 'client' is given to them as their .probe() arg.
> So you could just do a
> regmap = syscon_i2c_to_regmap(pdev->dev.parent);
>
> I've also noticed that the mmio syscon uses device_node as parameter. What
> was the reason to divert from that? Just curious.
This is a helper for I2C clients. There aren't any OF helpers in here
(yet). If you think they would be helpful we can add them. How do
you see them being used?
--
Lee Jones [李琼斯]
Senior Technical Lead - Developer Services
Linaro.org │ Open source software for Arm SoCs
Follow Linaro: Facebook | Twitter | Blog
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2020-07-02 7:15 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <20200622075145.1464020-1-lee.jones@linaro.org>
2020-06-30 9:16 ` [PATCH v4 1/1] mfd: Add I2C based System Configuaration (SYSCON) access Michael Walle
2020-06-30 22:32 ` Michael Walle
2020-07-01 7:04 ` Lee Jones
2020-07-01 21:01 ` Michael Walle
2020-07-02 6:54 ` Lee Jones
2020-07-02 7:02 ` Michael Walle
2020-07-02 8:18 ` Lee Jones
2020-07-02 9:12 ` Michael Walle
2020-07-02 7:14 ` Lee Jones [this message]
2020-07-02 7:21 ` Michael Walle
2020-07-05 13:10 ` kernel test robot
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200702071402.GP1179328@dell \
--to=lee.jones@linaro.org \
--cc=andriy.shevchenko@linux.intel.com \
--cc=arnd@arndb.de \
--cc=bgolaszewski@baylibre.com \
--cc=broonie@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=michael@walle.cc \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).